Breast tomosynthesis using the multiple projection algorithm adapted for stationary detectors.

OBJECTIVE: The aim of this study is to investigate the validity of using the Multiple Projection Algorithm (MPA) for Breast Tomosynthesis (BT) using real projection images acquired with phantoms at a clinical setting. METHODS: The CIRS-BR3D phantom with ranging thicknesses between 3 cm and 6 cm was used for all image quality evaluations. Five sets of measurements were acquired, each comprised of a 2D mammographic image followed by a set of 25 projections within an arc length of 50°. A reconstruction algorithm based on the MPA was adapted for partial isocentric rotation using a stationary detector. For reference purposes, a Back Projection (BP) algorithm was also developed for this geometry. The performance of the algorithms was evaluated, in combination with pre-filtering of the projections, in comparative studies that involved also a comparison between tomosynthesis slices and 2D mammograms. RESULTS: Evaluation of tomosynthesis slices reconstructed with BP and MPA showed close performance for the two algorithms with no considerable differences in feature detection, size and appearance of the background tissue with the MPA running faster the overall process. Pre-filtering of the projections, led to better BT images compared to non-filtering. Increased thickness resulted in limited detection of the features of interest, especially the smaller sized ones. In these cases, the filtered BT slices allowed improved visualization due to removed superimposed tissue compared to the 2D images. The different breast-like slab arrangements in phantoms of the same thickness demonstrated a slight influence on the quality of reconstructed features. CONCLUSIONS: The MPA which had been applied previously to reconstruct tomograms from projections acquired at synchrotron facilities, is a time efficient algorithm, and is fully compliant with and can be successfully used in BT clinical systems. Compared to 2D mammography, BT shows advantage in visualizing features of small size and for increased phantom thickness or features within a dense background with superimposed structures.

Image quality evaluation of breast tomosynthesis with synchrotron radiation.

PURPOSE: This study investigates the image quality of tomosynthesis slices obtained from several acquisition sets with synchrotron radiation using a breast phantom incorporating details that mimic various breast lesions, in a heterogeneous background. METHODS: A complex Breast phantom (MAMMAX) with a heterogeneous background and thickness that corresponds to 4.5 cm compressed breast with an average composition of 50% adipose and 50% glandular tissue was assembled using two commercial phantoms. Projection images using acquisition arcs of 24°, 32°, 40°, 48°, and 56° at incident energy of 17 keV were obtained from the phantom with the synchrotron radiation for medical physics beamline at ELETTRA Synchrotron Light Laboratory. The total mean glandular dose was set equal to 2.5 mGy. Tomograms were reconstructed with simple multiple projection algorithm (MPA) and filtered MPA. In the latter case, a median filter, a sinc filter, and a combination of those two filters were applied on the experimental data prior to MPA reconstruction. Visual inspection, contrast to noise ratio, contrast, and artifact spread function were the figures of merit used in the evaluation of the visualisation and detection of low- and high-contrast breast features, as a function of the reconstruction algorithm and acquisition arc. To study the benefits of using monochromatic beams, single projection images at incident energies ranging from 14 to 27 keV were acquired with the same phantom and weighted to synthesize polychromatic images at a typical incident x-ray spectrum with W target. RESULTS: Filters were optimised to reconstruct features with different attenuation characteristics and dimensions. In the case of 6 mm low-contrast details, improved visual appearance as well as higher contrast to noise ratio and contrast values were observed for the two filtered MPA algorithms that exploit the sinc filter. These features are better visualized at extended arc length, as the acquisition arc of 56° with 15 projection images demonstrates the highest image reconstruction quality. For microcalcifications, filtered MPA implemented with a combination of median and sinc filters indicates better feature appearance due to efficient suppression of background tissue. The image quality of these features is less sensitive to the acquisition arc. Calcifications with size ranging from 170 to 500 µm, like the ones presently studied, are well identified and visualized for all arcs used. The comparison of single projection images obtained under different beam conditions showed that the use of monochromatic beam can produce an image with higher contrast and contrast to noise ratio compared to an image corresponding to a polychromatic beam even when the latter is acquired with double incident exposure. CONCLUSIONS: Filter optimization in respect to the type of feature characteristics is important before the reconstruction. The MPA combined with median and sinc filters results in improved reconstruction of microcalcifications and low-contrast features. The latter are better visualized at extended arc length, while microcalcifications are less sensitive to this acquisition parameter. Use of monochromatic beams may result in tomographic images with higher contrast acquired at lower incident exposures.

Evaluation of an improved algorithm for producing realistic 3D breast software phantoms: application for mammography.

PURPOSE: This work presents an improved algorithm for the generation of 3D breast software phantoms and its evaluation for mammography. METHODS: The improved methodology has evolved from a previously presented 3D noncompressed breast modeling method used for the creation of breast models of different size, shape, and composition. The breast phantom is composed of breast surface, duct system and terminal ductal lobular units, Cooper's ligaments, lymphatic and blood vessel systems, pectoral muscle, skin, 3D mammographic background texture, and breast abnormalities. The key improvement is the development of a new algorithm for 3D mammographic texture generation. Simulated images of the enhanced 3D breast model without lesions were produced by simulating mammographic image acquisition and were evaluated subjectively and quantitatively. For evaluation purposes, a database with regions of interest taken from simulated and real mammograms was created. Four experienced radiologists participated in a visual subjective evaluation trial, as they judged the quality of the simulated mammograms, using the new algorithm compared to mammograms, obtained with the old modeling approach. In addition, extensive quantitative evaluation included power spectral analysis and calculation of fractal dimension, skewness, and kurtosis of simulated and real mammograms from the database. RESULTS: The results from the subjective evaluation strongly suggest that the new methodology for mammographic breast texture creates improved breast models compared to the old approach. Calculated parameters on simulated images such as beta exponent deducted from the power law spectral analysis and fractal dimension are similar to those calculated on real mammograms. The results for the kurtosis and skewness are also in good coincidence with those calculated from clinical images. Comparison with similar calculations published in the literature showed good agreement in the majority of cases. CONCLUSIONS: The improved methodology generated breast models with increased realism compared to the older model as shown in evaluations of simulated images by experienced radiologists. It is anticipated that the realism will be further improved using an advanced image simulator so that simulated images may be used in feasibility studies in mammography.

Evaluation of digital breast tomosynthesis reconstruction algorithms using synchrotron radiation in standard geometry.

PURPOSE: In this article, the image quality of reconstructed volumes by four algorithms for digital tomosynthesis, applied in the case of breast, is investigated using synchrotron radiation. METHODS: An angular data set of 21 images of a complex phantom with heterogeneous tissue-mimicking background was obtained using the SYRMEP beamline at ELETTRA Synchrotron Light Laboratory, Trieste, Italy. The irradiated part was reconstructed using the multiple projection algorithm (MPA) and the filtered backprojection with ramp followed by hamming windows (FBR-RH) and filtered backprojection with ramp (FBP-R). Additionally, an algorithm for reducing the noise in reconstructed planes based on noise mask subtraction from the planes of the originally reconstructed volume using MPA (MPA-NM) has been further developed. The reconstruction techniques were evaluated in terms of calculations and comparison of the contrast-to-noise ratio (CNR) and artifact spread function. RESULTS: It was found that the MPA-NM resulted in higher CNR, comparable with the CNR of FBP-RH for high contrast details. Low contrast objects are well visualized and characterized by high CNR using the simple MPA and the MPA-NM. In addition, the image quality of the reconstructed features in terms of CNR and visual appearance as a function of the initial number of projection images and the reconstruction arc was carried out. Slices reconstructed with more input projection images result in less reconstruction artifacts and higher detail CNR, while those reconstructed from projection images acquired in reduced angular range causes pronounced streak artifacts. CONCLUSIONS: Of the reconstruction algorithms implemented, the MPA-NM and MPA are a good choice for detecting low contrast objects, while the FBP-RH, FBP-R, and MPA-NM provide high CNR and well outlined edges in case of microcalcifications.

Health Technology Assessment and Biomedical Engineering: Global trends, gaps and opportunities.

The diffusion of medical devices is expanding at an astonishing rate. The increasing number of novel patents per year suggests this growth will continue. In contrast to drugs, medical devices are intrinsically dependent on the environment in which they are used and how they are maintained. This created an unprecedented global need for well-trained biomedical engineers who can help healthcare systems to assess them. The International Federation for Medical and Biological Engineering (IFMBE) is the global scientific society of biomedical engineers in official relations with the United Nations World Health Organisation (WHO) and has been very active in promoting the role of the biomedical engineer in Health Technology Assessment (HTA). The IFMBE Health Technology Assessment Division (HTAD) is the IFMBE operative branch in this field, promoting studies, projects and activities to foster the growth of this specific and very important science sector, including summer schools, training material, an HTA eLearning platform, HTA guidelines, awards and more. This article describes the vision, the mission and the strategy of the HTAD, with a focus on the results achieved and the impact this is having on global policymaking.

Simulation studies of field shaping in rotational radiation therapy.

This article presents simulation studies of field shaping in rotational radiation therapy by means of two categories of beam modifying devices: protectors and shapers. The protectors used are diminished copies of the organs at risk (OARs) and stay parallel to them during gantry rotation. Thus, each protector always keeps the corresponding OAR in its shadow, significantly reducing the irradiation. The shapers are used in order to obtain a more uniform dose distribution in the planning target volume (PTV) while preserving their initial orientation during gantry rotation. Thus, the use of beam modifying devices allows modulation of the beam intensity, to better fit irradiation requirements, at every gantry position. A software tool for calculations of geometrical position and dimensions of the beam modifying devices, using information about the shape, size, and position of the protected organ or area at risk as input, was developed. This tool was integrated into the in-house-developed Monte Carlo radiation therapy simulator (MCRTS), used to simulate the particle transport through the designed system. The verification of the software tool showed good agreement between experimental and simulation data, with discrepancies of less than 3%. Dose distributions in solid-geometry and voxel-based neck models were evaluated. Furthermore, the effectiveness of the shapers to modify the dose distribution outside the protected area was studied. Results demonstrated that the use of the shapers effectively improves dose uniformity. Studies using shapers of different materials were also carried out and resulted in similar dose distributions. The results of the simulation studies with a voxel-based model showed that rotational therapy with beam modifying devices offers adequate protection of the OAR and a uniform dose distribution outside the protected region.

Dual-energy mammography: simulation studies.

This paper presents a mammography simulator and demonstrates its applicability in feasibility studies in dual-energy (DE) subtraction mammography. This mammography simulator is an evolution of a previously presented x-ray imaging simulation system, which has been extended with new functionalities that are specific for DE simulations. The new features include incident exposure and dose calculations, the implementation of a DE subtraction algorithm as well as amendments to the detector and source modelling. The system was then verified by simulating experiments and comparing their results against published data. The simulator was used to carry out a feasibility study of the applicability of DE techniques in mammography, and more precisely to examine whether this modality could result in better visualization and detection of microcalcifications. Investigations were carried out using a 3D breast software phantom of average thickness, monoenergetic and polyenergetic beam spectra and various detector configurations. Dual-shot techniques were simulated. Results showed the advantage of using monoenergetic in comparison with polyenergetic beams. Optimization studies with monochromatic sources were carried out to obtain the optimal low and high incident energies, based on the assessment of the figure of merit of the simulated microcalcifications in the subtracted images. The results of the simulation study with the optimal energies demonstrated that the use of the DE technique can improve visualization and increase detectability, allowing identification of microcalcifications of sizes as small as 200 microm. The quantitative results are also verified by means of a visual inspection of the synthetic images.

Evaluation of the effect of silicone breast inserts on X-ray mammography and breast tomosynthesis images: A Monte Carlo simulation study.

PURPOSE: Breast augmentation is one of the most popular cosmetic surgeries worldwide. The aim of this study is to investigate the effect of breast implant insertion on the detectability and visibility of lesions on mammography and breast tomosynthesis (BT) images. MATERIALS AND METHODS: Three software phantoms, composed of a homogeneous background with embedded silicone gel structures, and two types of breast abnormalities, microcalcifications (µCs) and masses, were generated. Two X-ray breast imaging modalities were simulated: mammography and BT with six incident monochromatic X-ray beams with energies in the interval between 20 and 30 keV. Projection images were generated using an in-house developed Monte Carlo simulator. The detectability of mammographic findings adjacent to the implant material and the influence of the incident beam energy and implant thickness on the feature detection were studied. RESULTS: It was found that implants thicker than 26 mm for the case of mammography and 14 mm for the case of BT obscured the visibility of underlying structures. Although BT demonstrated a lack of contrast, this modality was able to visualize µCs under considerable depths of implant. Increasing the incident beam energy led to better visualization of small µCs, while in the case of breast masses, their detectability was limited. CONCLUSIONS: Silicone gel implants introduce a limitation in the image quality of mammograms resulting in low detectability of features. In addition, silicone gel implants obscure partially or totally parts of the image, depending on the size and the thickness of the implant as well the energy of the X-rays used.

Utilization of oral sucrose load during exercise in humans. Effect of the alpha-glucosidase inhibitor acarbose.

We investigated the hormonal and metabolic response to a 100-g sucrose load given 15 min after adaptation to moderate-intensity (50% VmaxO2) long-duration (4-h) exercise in healthy volunteers. The effect of a 100-mg dose of the alpha-glucosidase inhibitor Acarbose ingested with the sucrose load was also investigated. "Naturally labeled [13C] sucrose" was used to follow the conversion to expired-air CO2 of the sugar ingested by isotope-ratio mass spectrometry. Circulating hormone and metabolite data were obtained in nine subjects, and indirect calorimetry and stable isotope methodology were applied to six of them. Under placebo, 93 +/- 4 g sucrose were entirely oxidized during the 4 h of exercise, total carbohydrate utilization was 235 +/- 14 g, endogenous carbohydrate utilization was 142 +/- 13 g, and total lipid oxidation was 121 +/- 7 g. A single oral dose of 100 mg Acarbose ingested with the sucrose load did not significantly modify total carbohydrate (239 +/- 2 g/4 h) or lipid (122 +/- 6 g/4 h) oxidation. In contrast, sucrose oxidation was reduced to 53 +/- 6 g/4 h and endogenous carbohydrate utilization increased to 186 +/- 7 g/4 h. Reduction of the rises in blood glucose and fructose and of the increases in plasma insulin and C peptide under Acarbose confirmed these effects, whereas lower circulating levels of alanine suggested a higher rate of gluconeogenesis. These data show that a 100-g glucose load ingested soon after initiation of exercise is a perfect available metabolic substrate.(ABSTRACT TRUNCATED AT 250 WORDS)

Development and evaluation of an ODL course on Medical Image Processing.

Recent developments in the field of Biomedical Engineering have led to considerable improvement in health care delivery, but also impose continuous change and improvement in education and training schemes of its professionals, in order to assure appropriate front-line knowledge, competencies and skills. Open and distance learning provides a very effective means for continuous education and training purposes. Image processing may be used as an attractive case for exploring the Collaborative Learning Model (CLM) paradigm in Open Distance Learning (ODL). An on-line course on Medical Image Processing, following the principles of collaborative learning, has been developed and evaluated. Each concept of the course is available in three levels of complexity. The first level shows only a very general description, actually the main idea. If the user is interested to continue, a second level is accessible, where the concept is explained in a more detailed manner. Moreover, for some concepts requiring complicated mathematical proofs, a third level is available. The course has been used at the European Course on Biomedical Engineering organized by the Department of Medical Physics, University of Patras, Greece, and was positively evaluated by the students.

Glucose oxidation in relation to the size of the oral glucose loading dose.

Using "naturally labeled 13C-glucose" the conversion to expired air CO2 of 100, 66 and 33 g oral glucose loads was evaluated, during 7 hr, in 6 male healthy volunteers. The total amounts of exogenous glucose converted to expired air CO2 were proportional to the loading doses and averaged, in g/7 hr, 14.6 +/- 2.1 for 33 g, 20.8 +/- 2.1 for 66 g and 31.2 +/- 1.6 for 100 g. In contrast total glucose oxidation, evaluated by indirect calorimetry, was similar in the three groups and was not correlated with the dose of glucose given. The plasma insulin response was significantly correlated with the load of glucose (r = 0.86; p less than 0.001) whereas such correlation was not observed with the blood glucose response. Comparison with data available in the literature on the influence of the size of the oral glucose load on endogenous glucose production and on splanchnic glucose output suggests that the greater oxidation of exogenous glucose seen when the oral load of glucose is increased essentially results from a greater enrichment of the systemic glucose pool with exogenous glucose.

Remarkable metabolic availability of oral glucose during long-duration exercise in humans.

It was reported previously that glucose ingestion prior to or at the beginning of muscular exercise was a readily available metabolic substrate. The aim of this study was to see what percentage of carbohydrate utilization can be covered by glucose ingested regularly during exercise. Male healthy volunteers exercised for 285 min at approximately 45% of their individual maximal O2 uptake on a 10% uphill treadmill. After 15 min adaptation to exercise they received either 200 g (group G 200) or 400 g (group G 400) glucose (0.25 g X ml H2O-1) orally in eight equal doses repeated every 30 min (G 200 = 8 X 25 g, n = 4; G 400 = 8 X 50 g, n = 4). Indirect calorimetry was used to evaluate carbohydrate and lipid oxidation. Naturally labeled [13C]glucose was used to follow the oxidation of the exogenous glucose. Total carbohydrate oxidation was 341 +/- 22 and 332 +/- 32 g, lipid oxidation was 119 +/- 8 and 105 +/- 5 g, and exogenous glucose oxidation was 137 +/- 4 and 227 +/- 13 g (P less than 0.005) in groups G 200 and G 400, respectively. Endogenous glucose oxidation was about half in G 400 of what it was in G 200: 106 +/- 27 vs. 204 +/- 24 g (P less than 0.02). During the last hour of exercise, exogenous oxidation represented 55.3 and 87.5% of total carbohydrate oxidation for groups G 200 and G 400, respectively.(ABSTRACT TRUNCATED AT 250 WORDS)

Fructose utilization during exercise in men: rapid conversion of ingested fructose to circulating glucose.

The aim of the present study was to compare the metabolic fate of repeated doses of fructose or glucose ingested every 30 min during long-duration moderate-intensity exercise in men. Healthy volunteers exercised for 3 h on a treadmill at 45% of their maximal oxygen consumption rate. "Naturally labeled" [13C]glucose or [13C]fructose was given orally at 25-g doses every 30 min (total feeding: 150 g; n = 6 in each group). Substrate utilization was evaluated by indirect calorimetry, and exogenous sugar oxidation was measured by isotope ratio mass spectrometry on expired CO2. Results were corrected for baseline drift in 13C/12C ratio in expired air due to exercise alone. Fructose conversion to plasma glucose was measured combining gas chromatography and isotope ratio mass spectrometry. Most of the ingested glucose was oxidized: 81 +/- 4 vs. 57 +/- 2 g/3 h for fructose (2P < 0.005). Exogenous glucose covered 20.8 +/- 1.4% of the total energy need (+/- 6.7 MJ) compared with 14.0 +/- 0.6% for fructose (2P < 0.005). The contribution of total carbohydrates was significantly higher and that of lipids significantly lower with glucose than with fructose. The blood glucose response was similar in both protocols. From 90 to 180 min, 55-60% of circulating glucose was derived from ingested fructose. In conclusion, when ingested repeatedly during moderate-intensity prolonged exercise, fructose is metabolically less available than glucose, despite a high rate of conversion to circulating glucose.

A method for selective removal of out-of-plane structures in digital tomosynthesis.

The quality of the reconstructed images in Digital Tomosynthesis is often limited by the presence of artifacts due to blur from planes other than the fulcrum plane. A technique has been developed for the separation and subsequent removal of unrelated structures from the reconstructed plane. The method involves the reconstruction of the blur originating in user-selected "noisy" planes as it appears on the plane of interest. This is achieved by projecting the reconstructed images of the selected plane on the image formation plane for all viewing angles, and subsequently, synthesizing its blurred image on the plane of interest. There are no restrictions as to the identity of the planes to be removed. Reproduction of the noise is performed using the tomosynthesis algorithm itself, thus the technique can be modified to suit any reconstruction algorithm. The proposed technique was implemented on the Multiple Projection Algorithm and was experimentally evaluated using a radiotherapy simulator unit.

A multiple projection method for digital tomosynthesis.

A new method of optimized efficiency for the retrospective reconstruction of tomograms is presented. The method has been developed for use with isocentric fluoroscopic units and is capable of performing digital tomosynthesis of anatomical planes of user selected orientation and distance from the isocenter. Optimization of efficiency has been achieved by segmenting the reconstruction process into discrete transformations that are specific to groups of pixels, rather than performing pixel by pixel operations. These involve a number of projections of the acquired image matrices as well as parallel translations and summing. Application of this method has resulted in a significant reduction of computing time. The proposed algorithm has been experimentally tested on a radiotherapy simulator unit with the use of a phantom and the obtained results are reported and discussed.

A three-dimensional breast software phantom for mammography simulation.

This paper presents a methodology for three-dimensional (3D) computer modelling of the breast, using a combination of 3D geometrical primitives and voxel matrices that can be further subjected to simulated x-ray imaging, to produce synthetic mammograms. The breast phantom is a composite model of the breast and includes the breast surface, the duct system and terminal ductal lobular units. Cooper's ligaments, the pectoral muscle, the 3D mammographic background and breast abnormalities. A second analytical x-ray matter interaction modelling module is used to generate synthetic images from monoenergetic fan beams. Mammographic images of various synthesized breast models differing in size, shape and composition were produced. A preliminary qualitative assessment performed by three radiologists and a quantitative evaluation study using fractal and grey-level histogram analysis were conducted. A comparative study of extracted features with published data has also been performed. The evaluation results indicated good correlation of characteristics between synthetic and actual radiographs. Applications foreseen are not only in the area of breast imaging experimentation but also in education and training.

Radiographic skills learning: procedure simulation using adaptive hypermedia.

The design and development of a simulation tool supporting learning of radiographic skills is reported. This tool has by textual, graphical and iconic resources, organized according to a building-block, adaptive hypermedia approach, which is described and supported by an image base of radiographs. It offers interactive user-controlled simulation of radiographic imaging procedures. The development is based on a commercially available environment (Toolbook 3.0, Asymetrix Corporation). The core of the system is an attributed precedence (priority) graph, which represents a task outline (concept and resources structure), which is dynamically adjusted to selected procedures. The user interface imitates a conventional radiography system, i.e. operating console, tube, table, patient and cassette. System parameters, such as patient positioning, focus-to-patient distance, magnification, field dimensions, tube voltage and mAs are under user control. Their effects on image quality are presented, by means of an image base acquired under controlled exposure conditions. Innovative use of hypermedia, computer based learning and simulation principles and technology in the development of this tool resulted in an enhanced interactive environment providing radiographic parameter control and visualization of parameter effects on image quality.

A software data generator for radiographic imaging investigations.

A software data generation tool, intended to be used in radiographic applications, has been developed. The application integrates a phantom design module and an imaging simulator. Phantoms can be described as a set of either geometrical objects or voxels, or contours drawn on multiple tomographic slices. Radiographic projections of the phantoms are formed on the basis of a simulated irradiation process, with selectable imaging parameters. Comparison between actual projection images from a physical and a simulated phantom shows good correspondence. The application was used for digital tomosynthesis (DTS) investigations and has proven to be a useful tool in the study of tomographic noise. Further development is expected to expand the use of the application to more areas of radiological imaging research.

In-house development of test equipment for quality control and training. Case study: a prototype ECG simulator-tester.

The support services for biomedical technology address a variety of technical and administrative issues, concerning the safe and efficient operation of medical equipment over the period of its intended use and the training of hospital personnel in issues concerning safety and quality. Clinical Engineering Departments undertake the responsibility of developing and operating training programs in medical equipment utilisation apart from the traditional role of training and supervising technicians involved in testing, calibration and preventive/corrective maintenance of electromedical equipment. In view of the above, the Institute of Biomedical Technology and the Centre of Biomedical Engineering collaborated for the design and development of a prototype digital ECG and arrhythmia simulator. In the absence of internationally accepted inspection protocols for ECG simulators, the verification phase of the project involved mainly the inspection of the device's conformity to its initial technical specifications. The results demonstrated that this tester. due to simplicity in construction and easiness of use could be a practical, reliable and economical solution for electrocardiograph and ECG monitor testing and waveform recognition training.

Three-dimensional localisation based on projectional and tomographic image correlation: an application for digital tomosynthesis.

Accurate three-dimensional tumor localisation in Radiotherapy, is critical to the treatment outcome, particularly when high dose gradients are present. A number of techniques have been proposed for the localisation of anatomical structures or markers. The present study proposes an approach to a concurrent maximisation of localisation accuracy and efficiency by correlation of tomographic and projectional images. The method introduces an element of direct verification and interactive optimisation of the process. Tomographic images are used for the identification of a point of interest. Its position is computed within the treatment co-ordinate system and verification of this position is achieved by obtaining the beam's eye view of the identified point on two projection radiographs. The key element of the approach is that all images used should be part of one single image data set. The implementation of this localisation method, as part of the functionality of a Digital Tomosynthesis prototype, has provided an integrated facility for localisation, of optimised accuracy and precision, while easy and efficient to use. The considerations are general and apply in principle to any imaging system that can augment tomographic images with projections.