RESUMEN
We report the observation of sub-Doppler cooling of lithium using an irregular-tetrahedral laser beam arrangement, which is produced by a nanofabricated diffraction grating. We are able to capture 11(2)% of the lithium atoms from a grating magneto-optical trap into Λ-enhanced D1 gray molasses. The molasses cools the captured atoms to a radial temperature of 60(9) µK and an axial temperature of 23(3) µK. In contrast to results from conventional counterpropagating beam configurations, we do not observe cooling when our optical fields are detuned from Raman resonance. An optical Bloch equation simulation of the cooling dynamics agrees with our data. Our results show that grating magneto-optical traps can serve as a robust source of cold atoms for tweezer-array and atom-chip experiments, even when the atomic species is not amenable to sub-Doppler cooling in bright optical molasses.
RESUMEN
We demonstrate operation of a constant-pressure flowmeter capable of generating and accurately measuring flows as low as 2 × 10-13 mol/s. Generation of such small flows is accomplished by using a small conductance element with C ≈ 50 nL/s. Accurate measurement then requires both low outgassing materials (< 1 × 10-15 mol/s) and small volume changes (≈ 70 µL). We outline the present flowmeter's construction, detail its operation, and quantify its uncertainty. The type-B uncertainty is < 0.2 % (k = 1) over the entire operating range. In particular, we present an analysis of its hydraulic system, and quantify the shift and uncertainty due to the slightly compressible oil. Finally, we compare our flowmeter against a NIST standard flowmeter, and find agreement to within 0.5 % (k = 2).
RESUMEN
Passive and active technologies have been used to control propellant boil-off, but the current state of understanding of cryogenic evaporation and condensation in microgravity is insufficient for designing large cryogenic depots critical to the long-term space exploration missions. One of the key factors limiting the ability to design such systems is the uncertainty in the accommodation coefficients (evaporation and condensation), which are inputs for kinetic modeling of phase change. A novel, combined experimental and computational approach is being used to determine the accommodation coefficients for liquid hydrogen and liquid methane. The experimental effort utilizes the Neutron Imaging Facility located at the National Institute of Standards and Technology (NIST) in Gaithersburg, Maryland to image evaporation and condensation of hydrogenated propellants inside of metallic containers. The computational effort includes numerical solution of a model for phase change in the contact line and thin film regions as well as an CFD effort for determining the appropriate thermal boundary conditions for the numerical solution of the evaporating and condensing liquid. Using all three methods, there is the possibility of extracting the accommodation coefficients from the experimental observations. The experiments are the first known observation of a liquid hydrogen menisci condensing and evaporating inside aluminum and stainless steel cylinders. The experimental technique, complimentary computational thermal model and meniscus shape determination are reported. The computational thermal model has been shown to accurately track the transient thermal response of the test cells. The meniscus shape determination suggests the presence of a finite contact angle, albeit very small, between liquid hydrogen and aluminum oxide.
RESUMEN
We create a pair of symmetric Bitter-type electromagnet assemblies capable of producing multiple field configurations including uniform magnetic fields, spherical quadruple traps, or Ioffe-Pritchard magnetic bottles. Unlike other designs, our coil allows both radial and azimuthal cooling water flows by incorporating an innovative 3D-printed water distribution manifold. Combined with a double-coil geometry, such orthogonal flows permit stacking of non-concentric Bitter coils. We achieve a low thermal resistance of 4.2(1) °C kW-1 and high water flow rate of 10.0(3) l min-1 at a pressure of 190(10) kPa.
RESUMEN
The NIST on a Chip (NOAC) program's central idea is the idea that measurement technology can be developed to enable metrology to be performed "outside the National Metrology Institute" by the creation of deployed and often miniaturized standards. These standards, when based on fundamental properties of nature, are directly tracible to the international system of units known as the SI. NIST is also developing quantum-based standards for SI traceability known as QSI, or Quantum based International System of units. Specifically, this paper will cover NIST efforts in the area of thermodynamic metrology to develop NOAC standards for pressure, vacuum and temperature measurements.
RESUMEN
We present a wide-bandwidth, voltage-controlled current source that is easily integrated with radiofrequency magnetic field coils. Our design uses current feedback to compensate for the frequency-dependent impedance of a radiofrequency antenna. We are able to deliver peak currents greater than 100 mA over a 300 kHz to 54 MHz frequency span. The radiofrequency current source fits onto a printed circuit board smaller than 4 cm2 and consumes less than 1.3 W of power. It is suitable for use in deployable quantum sensors and nuclear magnetic resonance systems.
RESUMEN
We demonstrate a compact (0.25 L) system for laser cooling and trapping atoms from a heated dispenser source. Our system uses a nanofabricated diffraction grating to generate a magnetooptical trap (MOT) using a single input laser beam. An aperture in the grating allows atoms from the dispenser to be loaded from behind the chip, increasing the interaction distance of atoms with the cooling light. To take full advantage of this increased distance, we extend the magnetic field gradient of the MOT to create a Zeeman slower. The MOT traps approximately 106 7Li atoms emitted from an effusive source with loading rates greater than 106 s-1. Our design is portable to a variety of atomic and molecular species and could be a principal component of miniaturized cold-atom-based technologies.
RESUMEN
We demonstrate loading of a Li magneto-optical trap using light-induced atomic desorption. The magnetooptical trap confines up to approximately 4 × 104 7Li atoms with loading rates up to approximately 4 × 103 atoms per second. We study the Li desorption rate as a function of the desorption wavelength and power. The extracted wavelength threshold for desorption of Li from fused silica is approximately 470 nm. In addition to desorption of lithium, we observe light-induced desorption of background gas molecules. The vacuum pressure increase due to the desorbed background molecules is â² 50 % and the vacuum pressure decreases back to its base value with characteristic timescales on the order of seconds when we extinguish the desorption light. By examining both the loading and decay curves of the magneto-optical trap, we are able to disentangle the trap decay rates due to background gases and desorbed lithium. Our results show that light-induced atomic desorption can be a viable Li vapor source for compact devices and sensors.
RESUMEN
We demonstrate and characterize a source of Li atoms made from direct metal laser sintered titanium. The source's outgassing rate is measured to be 5(2) × 10-7 Pa L s-1 at a temperature T = 330 °C, which optimizes the number of atoms loaded into a magneto-optical trap. The source loads ≈1077Li atoms in the trap in ≈1 s. The loaded source weighs 700 mg and is suitable for a number of deployable sensors based on cold atoms.
RESUMEN
Piston gauges or pressure balances are widely used to realize the SI unit of pressure, the pascal, and to calibrate pressure sensing devices. However, their calibration is time consuming and requires a lot of technical expertise. In this paper, we propose an alternate method of performing a piston gauge cross calibration that incorporates a pressure transducer as an immediate in-situ transfer standard. For a sufficiently linear transducer, the requirement to exactly balance the weights on the two pressure gauges under consideration is greatly relaxed. Our results indicate that this method can be employed without a significant increase in measurement uncertainty. Indeed, in the test case explored here, our results agreed with the traditional method within standard uncertainty, which was less than 6 parts per million.