Еlectrospun сellulose acetate membranes decorated with curcumin-PVP particles: preparation, antibacterial and antitumor activities.

Curcumin (Curc) exhibits anti-inflammatory, antibacterial and antitumor activity. However, its clinical application is limited by its poor bioavailability related to its extremely low water solubility. Novel materials allowing enhanced release of Curc in aqueous medium were obtained. The new materials consisted of electrospun fibers from cellulose acetate (CA) (mean fiber diameter ca. 780 nm ± 110 nm) with electrosprayed Curc/polyvinylpyrrolidone (Curc/PVP) particles. Scanning electron microscopy (SEM) showed that separated and evenly distributed particles of Curc/PVP were deposited on the surface of the mats and on the inner layers of the mat. X-ray diffraction studies showed that Curc was in amorphous state. In vitro studies demonstrated that Curc release was facilitated from Curc/PVP-on-CA mats (ca. 78% for 24 h) compared with the materials in which Curc was incorporated in CA fibers (17% for 24 h). Moreover, the curcumin-containing materials exhibited antibacterial activity against Gram-positive bacteria Staphylococcus aureus (S. aureus) and Gram-negative bacteria Escherichia coli (E. coli). Curc/PVP-on-CA fibrous mats exhibited high in vitro cytotoxicity towards HeLa tumor cells. Therefore, the obtained materials are promising for antibacterial wound dressing applications as well as for application in local treatment of cervical tumors.

Imparting Photocatalytic and Antioxidant Properties to Electrospun Poly(L-lactide-co-D,L-lactide) Materials.

The focus of the present study is on the fabrication of effective and eco-friendly hybrid electrospun materials based on poly(L-lactide-co-D,L-lactide) (PLDLLA), Fe3O4 and ZnO with an appropriate design for antioxidant and photocatalytic performance. The design of the fibrous materials was purposely tailored in one step by electrospinning and simultaneous electrospinning/electrospraying. Electrospinning of PLDLLA and its mixture with Fe3O4 resulted in the fabrication of materials with design type "in". Furthermore, the surface of the electrospun PLDLLA and Fe3O4-in-PLDLLA was decorated with ZnO particles by simultaneous electrospraying, thus materials with design type "on" were obtained. In this case, quaternized N,N,N-trimethyl chitosan iodide (QCOS) was used as a sticking agent of ZnO particles onto the fiber's surface. Different structures and morphologies of the electrospun materials were observed by SEM equipped with EDX and TEM. TGA and XRD analyses show that the presence of inorganic particles had an impact on the thermal properties and crystallinity of the electrospun materials. Furthermore, the material type "on" showed improved wettability with a water contact angle less than 90° compared to the material type "in" with an angle larger than 90°. In particular, the presence of Fe3O4 imparts complementary magnetic properties, while ZnO considerably increased the antioxidant activity of the fibrous materials. Materials with design type "on" displayed over 70% radical scavenging capacity in contrast to the material type "in" with less than 20% capacity within 30 min of contact. Moreover, the purposely tailored design type "on" materials provided excellent photocatalytic degradation of model organic pollutant methylene blue dye under UV light irradiation even after 5-fold use, and at the end of the fifth cycle these materials degraded more than 90% of the dye. These results reveal not only a strategy for the fabrication of electrospun hybrid bio-based materials with targeted design but also provide a promising, simple and effective way for mitigating water pollution.

Fabrication of Electrospun Cellulose Acetate/Nanoclay Composites for Pollutant Removal.

The creation of eco-friendly clay-based composites for pollutant removal by adsorption still remains a challenge. This problem might be successfully solved by the development of electrospun polymer-clay composites. For the first time in this study, a one-step fabrication of cellulose acetate (CA) fibers filled with commercially available nanoclays (NCs) was described. The optimal ratio at which CA/NCs dispersions remained stable was accomplished by varying the nanoclay concentration with respect to CA. Furthermore, the selected solvent system and the electrospinning conditions allowed for the successful fabrication of electrospun CA/NC composites. It was found that the composites' surface morphology was not affected by the incorporated nanoclays and was the same as that of the electrospun CA fibers. The performed analyses clearly showed that CA and nanoclays did not react during the electrospinning process. It was found that the distribution of nanoclay layers probably was a mixture of intercalated and exfoliated structures. Notably, the type of the nanoclay strongly influenced the adsorption ability of CA/NC composites toward Cr(VI) ions and MB dye. These results suggested that the fabricated CA/NC composites are suitable for pollutant removal due to their specific structure.

Cellulose Acetate-Based Electrospun Materials with a Variety of Biological Potentials: Antibacterial, Antifungal and Anticancer.

Novel eco-friendly fibrous materials with complex activities from cellulose acetate and cellulose acetate/polyethylene glycol (CA,PEG) containing 5-chloro-8-hydroxyquinoline as a model drug were obtained by electrospinning. Several methods, including scanning electron microscopy, X-ray diffraction analysis, ultraviolet-visible spectroscopy, water contact angle measurements, and mechanical tests, were utilized to characterize the obtained materials. The incorporation of PEG into the fibers facilitated the drug release. The amounts of the released drug from CA/5-Cl8Q and CA,PEG/5-Cl8Q were 78 ± 3.38% and 86 ± 3.02%, respectively (for 175 min). The antibacterial and antifungal activities of the obtained materials were studied. The measured zones of inhibition of CA/5-Cl8Q and CA,PEG/5-Cl8Q mats were 4.0 ± 0.18 and 4.5 ± 0.2 cm against S. aureus and around 4.0 ± 0.15 and 4.1 ± 0.22 cm against E. coli, respectively. The complete inhibition of the C. albicans growth was detected. The cytotoxicity of the obtained mats was tested toward HeLa cancer cells, SH-4 melanoma skin cells, and mouse BALB/c 3T3 fibroblasts as well. The CA/5-Cl8Q and CA,PEG/5-Cl8Q materials exhibited anticancer activity and low normal cell toxicity. Thus, the obtained fibrous materials can be suitable candidates for wound dressing applications and for application in local cancer treatment.

Electrospun Polymer-Fungicide Nanocomposites for Grapevine Protection.

Nowadays, diseases in plants are a worldwide problem. Fungi represent the largest number of plant pathogens and are responsible for a range of serious plant diseases. Esca is a grapevine disease caused mainly by fungal pathogens Phaeomoniella chlamydospora (P. chlamydospora) and Phaeoacremonium aleophilum (P. aleophilum). The currently proposed methods to fight esca are not curative. In this study, polymer composites based on biodegradable polymer containing chemical fungicides with antifungal activity were successfully prepared by electrospinning. The obtained materials were hydrophobic with good mechanical properties. In vitro studies demonstrated that the fungicide release was higher from PLLA/K5N8Q fibrous mats (ca. 72% for 50 h) compared to the released drug amount from PLLA/5-Cl8Q materials (ca. 52% for 50 h), which is due to the better water-solubility of the salt. The antifungal activity of the fibrous materials against P. chlamydospora and P. aleophilum was studied as well. The incorporation of the fungicide in the biodegradable fibers resulted in the inhibition of fungal growth. The obtained materials are perspective candidates for the protection of vines from the penetration and growth of fungal pathogens.

Electrospun curcumin-loaded cellulose acetate/polyvinylpyrrolidone fibrous materials with complex architecture and antibacterial activity.

Novel fibrous materials from cellulose acetate (CA) and polyvinylpyrrolidone (PVP) containing curcumin (Curc) with original design were prepared by one-pot electrospinning or dual spinneret electrospinning. The electrospun materials were characterized by scanning electron microscopy (SEM), fluorescence microscopy, Fourier transform infrared spectroscopy (FTIR), ultraviolet-visible spectroscopy (UV-Vis), differential scanning calorimetry (DSC), water contact angle measurements, and microbiological tests. It was found that the incorporation of Curc into the CA and PVP solutions resulted in an increase of the solution viscosity and obtaining fibers with larger diameters (ca. 1.5µm) compared to the neat CA (ca. 800nm) and PVP fibers (ca. 500nm). The incorporation of PVP resulted in increased hydrophilicity of the fibers and in faster Curc release. Curc was found in the amorphous state in the Curc-containing fibers and these mats exhibited antibacterial activity against Staphylococcus aureus (S. aureus). The results suggest that, due to their complex architecture, the obtained new antibacterial materials are suitable for wound dressing applications, which necessitate diverse release behaviors of the bioactive compound.