Fluorine-Containing Triazole-Decorated Silver(I)-Based Cationic Metal-Organic Framework for Separating Organic Dyes and Removing Oxoanions from Water.

Four new triazole-decorated silver(I)-based cationic metal-organic frameworks (MOFs), {[Ag(L1)](BF4)}n (1), {[Ag(L1)](NO3)}n (2), {[Ag(L2)](BF4)}n (3), and {[Ag(L2)](NO3)}n (4), have been synthesized using two newly designed ligands, 3-fluoro-5-(4H-1,2,4-triazol-4-yl)pyridine (L1) and 3-(4H-1,2,4-triazol-4-yl)-5-(trifluoromethyl)pyridine (L2). When the fluorine atom was changed to a trifluoromethyl group at the same position, tremendous enhancement in the MOF dimensionality was achieved [two-dimensional to three-dimensional (3D)]. However, changing the metal salt (used for the synthesis) had no effect. The higher electron-withdrawing tendency of the trifluoromethyl group in L2 aided in the formation of higher-dimensional MOFs with different properties compared with those of the fluoro derivatives. The fluoride group was introduced in the ligand to make highly electron-deficient pores inside the MOFs that can accelerate the anion-exchange process. The concept was proved by density functional theory calculation of the MOFs. Both 3D cationic MOFs were used for dye adsorption, and a remarkable amount of dye was adsorbed in the MOFs. In addition, owing to their cationic nature, the MOFs selectively removed anionic dyes from a mixture of anionic, cationic, and neutral dyes in the aqueous phase. Interestingly, the present MOFs were also highly effective for the removal of oxoanions (MnO4- and Cr2O72-) from water.

Facile Synthesis of Self-Supported Solid Amine Sorbents for Direct Air Capture.

Conventional usage of tetraethylenepentamine (TEPA) via being supported on porous solid materials for carbon capture is susceptible to oxidative degradation during regeneration cycles. This study reports a novel method to synthesize a TEPA based solid polymer for efficient CO2 removal via direct air capture (DAC). The polymer was obtained through epoxy-amine crosslinking reaction, leading to the transformation of liquid TEPA to a self-supported solid polymer. The synthesis was conducted under ambient conditions via a one-pot process with no waste products, which is aligned with green synthesis. The performance of the solid amine was evaluated in DAC under realistic conditions and compared with TEPA supported on SiO2 and zeolite 13X prepared through the conventional method. The solid TEPA amine exhibited a high CO2 uptake of 6.2 wt.% comparable to the conventional counterparts. More importantly, the solid TEPA amine demonstrated high resistance to oxidation during the accelerated ageing process at 80 °C in air for 24 h, whereas the two supported TEPA samples experienced severe degradation, with zeolite 13X supported TEPA incurring a reduction of 86.5 % in CO2 capturing capacity after the ageing. This work sheds light on the novel usage of TEPA as an efficient solid amine for practical DAC operation.

Advancing hyper-crosslinked materials with high efficiency and reusability for oil spill response.

Developing materials with high efficiency for recovering oil to mitigate the environmental impact of oil spills has always been a challenging task. A commercial melamine formaldehyde sponge was coated with an optimised superhydrophobic/superoleophilic hyper-crosslinked polymer and applied to the removal of crude oil from oil-in-water emulsions for the improvement of oil spill clean-up processes. The high surface area, porosity, hydrophobicity, and selectivity of oil over water made the hyper-crosslinked polymer coated sponge (HPCS) an ideal sorbent for efficient oil/water separation. The system was able to strip crude oil from water emulsions of 1000 ppm to a negligible level of 2 ppm oil with minimal amounts of the HPCS material. More importantly, the HPCS material could be reused via a simple mechanical compression process, and the uptake capacity was retained over ten cycles. For five cycles of oil adsorption/mechanical compression the HPCS was able to provide water filtrate with oil concentrations of under 15 ppm. This is an effective and economical recovery system, removing the need for consistent solvent washing and drying processes. These results suggest that the HPCS is a promising material for oil/water separation and recovery under challenging conditions.

Experimental research on surface acoustic wave microfluidic atomization for drug delivery.

This paper demonstrates that surface acoustic wave (SAW) atomization can produce suitable aerosol concentration and size distribution for efficient inhaled lung drug delivery and is a potential atomization device for asthma treatment. Using the SAW device, we present comprehensive experimental results exploring the complexity of the acoustic atomization process and the influence of input power, device frequency, and liquid flow rate on aerosol size distribution. It is hoped that these studies will explain the mechanism of SAW atomization aerosol generation and how they can be controlled. The insights from the high-speed flow visualization studies reveal that it is possible by setting the input power above 4.17 W, thus allowing atomization to occur from a relatively thin film, forming dense, monodisperse aerosols. Moreover, we found that the aerosol droplet size can be effectively changed by adjusting the input power and liquid flow rate to change the film conditions. In this work, we proposed a method to realize drug atomization by a microfluidic channel. A SU-8 flow channel was prepared on the surface of a piezoelectric substrate by photolithography technology. Combined with the silicon dioxide coating process and PDMS process closed microfluidic channel was prepared, and continuous drug atomization was provided to improve the deposition efficiency of drug atomization by microfluidic.

A palladium polyaniline complex: a simple and efficient catalyst for batch and flow Suzuki-Miyaura cross-couplings.

A novel palladium polyaniline complex (Pd@PANI) was synthesized via a one-pot method using a low concentration of hydrogen peroxide (3 wt%) as a mild oxidant. Pd@PANI was employed to catalyze Suzuki-Miyaura cross-couplings with 0.11 ppm levels of palladium and high turnover numbers (up to 6.1 × 104). Various aromatic halides and aromatic boric acids were used as reaction partners to prepare the biaryl compounds in high yields. Application of the method in the synthesis of D-fructose derivatives was also performed. Furthermore, the catalyst was evaluated under a flow process to provide the corresponding products in good yields with shorter residence times and lower temperatures in more convenient operations compared with the batch conditions.

Modeling and experimental analysis of the linear ultrasonic motor with in-plane bending and longitudinal mode.

A novel linear ultrasonic motor based on in-plane longitudinal and bending mode vibration is presented in this paper. The stator of the motor is composed of a metal plate and eight piezoelectric ceramic patches. There are four long holes in the plate, designed for consideration of the longitudinal and bending mode coupling. The corresponding model is developed to optimize the mechanical and electrical coupling of the stator, which causes an ellipse motion at the contact tip of the stator when the composite vibrations with longitudinal and bending are excited. Its harmonic and transient responses are simulated and inspected. A prototype based on the model is fabricated and used to conduct experiments. Results show that the amplitude of the stator's contact tips is significantly increased, which helps to amplify the driving force and speed of the motor. It is therefore feasible to implement effective linear movement using the developed prototype.