Enamel remineralization effect of a dentifrice containing calcium sodium phosphosilicate: an optical coherence tomography observation.

OBJECTIVE: The purpose of this study was to examine the effects of a dentifrice containing 5% calcium sodium phosphosilicate (CSP) on the remineralization of the enamel using optical coherence tomography (OCT). MATERIALS AND METHODS: Bovine incisors were sliced and shaped in a rectangular form. One group of five specimens was treated with undersaturated 0.1 M lactic acid buffer solution (pH 4.75) for 10 min and then placed in artificial saliva (pH 7.0) (De group). Other specimens were stored in solutions of toothpaste containing CSP for 10 min, followed by 10-min immersion in the lactic acid buffer solution twice a day before storage in artificial saliva (CSP group). An additional group was stored in only artificial saliva (control group). OCT imaging on the selected location of the enamel surface was performed. The peak intensity and width at 1/e2 were recorded in each of the six areas on the sample and averaged, and the sample size of each group was six. The integrated value in units (dB × µm) was calculated in the area of peak intensity. The data for each group was subjected to one-way repeated-measures ANOVA and Tukey HSD tests (α = 0.05). RESULTS: The changes in integrated values of each group were different. A slight but significant increase in the integrated value was observed in the control group, whereas a slight but significant decrease in the value was observed the De group. Integrated values increased in the CSP group. CONCLUSIONS: Remineralization occurred upon immersion in the toothpaste containing CSP.

Influence of surface treatment on bonding of resin luting cement to CAD/CAM composite blocks.

The aim of this study was to determine the influence of different surface treatments of CAD/CAM composite blocks on bonding effectiveness of resin cements, based on the shear bond strength test and the surface science examination. Specimens were fabricated from two types of CAD/CAM composite blocks (Cerasmart and VITA Enamic), and the specimen surfaces were alumina sandblasted. Specimen surfaces were treated with i) silane, ii) primer, and iii) silane+primer, then two types of cements (Block HC Cem and Super Bond) were bonded. After 24 h storage, bond strengths were measured. Surface free energy measurements were performed of the treated CAD/CAM composite blocks surfaces. The groups ii) and iii) showed significantly higher bond strengths than the group i), apart from VITA Enamic with Block HC Cem. Although the total surface free energy showed different trends in different surface treatments, a similar trend was found in both CAD/CAM composite blocks.

Effect of acid erosion on enamel bond strength of self-etch adhesives and sonic velocity measurement of enamel.

The purpose of this study was to investigate the effect of acid erosion on the bonding performance of universal adhesives. Freshly extracted bovine teeth were cut into enamel slabs and assigned to either the Er or the control group. Specimens in the Er group were immersed in citric acid solution (pH 2.1) twice a day and stored in artificial saliva, while control specimens were simply stored in artificial saliva. Differences in the mean values between the control and Er groups were greater than expected, despite accounting for the effect of differences in the adhesive systems (p=0.016). The Er group mainly exhibited cohesive failure in the enamel, while adhesive failure was more frequent in the control group. The sonic velocity was found to decrease over time in the acid attacked specimens. The results indicated that bond strengths of universal adhesive tested increased in eroded enamel.

Influence of air-powder polishing on bond strength and surface-free energy of universal adhesive systems.

The influences of air-powder polishing with glycine or sodium bicarbonate powders on shear bond strengths (SBS) and surface-free energies of universal adhesives were examined. Scotchbond Universal Adhesive (SU, 3M ESPE), G-Premio Bond (GP, GC), Adhese Universal (AU, Ivoclar Vivadent), and All-Bond Universal (AB, Bisco) were used in this study. Bovine dentin surfaces were air polished with glycine or sodium bicarbonate powders prior to the bonding procedure, and resin pastes were bonded to the dentin surface using universal adhesives. SBSs were determined after 24-h storage in distilled water at 37°C. Surface-free energy was then determined by measuring contact angles using three test liquids on dentin surfaces. Significantly lower SBSs were observed for dentin that was air-powder polished and surface-free energies were concomitantly lowered. This study indicated that air-powder polishing influences SBSs and surface-free energies. However, glycine powder produced smaller changes in these surface parameters than sodium bicarbonate.