Water- and heat-activated dynamic passivation for perovskite photovoltaics.

Further improvements in perovskite solar cells require better control of ionic defects in the perovskite photoactive layer during the manufacturing stage and their usage1-5. Here we report a living passivation strategy using a hindered urea/thiocarbamate bond6-8 Lewis acid-base material (HUBLA), where dynamic covalent bonds with water and heat-activated characteristics can dynamically heal the perovskite to ensure device performance and stability. Upon exposure to moisture or heat, HUBLA generates new agents and further passivates defects in the perovskite. This passivation strategy achieved high-performance devices with a power conversion efficiency (PCE) of 25.1 per cent. HUBLA devices retained 94 per cent of their initial PCE for approximately 1,500 hours of ageing at 85 degrees Celsius in nitrogen and maintained 88 per cent of their initial PCE after 1,000 hours of ageing at 85 degrees Celsius and 30 per cent relative humidity in air.

Dimensional Regulation from 1D/3D to 2D/3D of Perovskite Interfaces for Stable Inverted Perovskite Solar Cells.

Constructing low-dimensional/three-dimensional (LD/3D) perovskite solar cells can improve efficiency and stability. However, the design and selection of LD perovskite capping materials are incredibly scarce for inverted perovskite solar cells (PSCs) because LD perovskite capping layers often favor hole extraction and impede electron extraction. Here, we develop a facile and effective strategy to modify the perovskite surface by passivating the surface defects and modulating surface electrical properties by incorporating morpholine hydriodide (MORI) and thiomorpholine hydriodide (SMORI) on the perovskite surface. Compared with the PI treatment that we previously developed, the one-dimensional (1D) perovskite capping layer derived from PI is transformed into a two-dimensional (2D) perovskite capping layer (with MORI or SMORI), achieving dimension regulation. It is shown that the 2D SMORI perovskite capping layer induces more robust surface passivation and stronger n-N homotype 2D/3D heterojunctions, achieving a p-i-n inverted solar cell with an efficiency of 24.55%, which retains 87.6% of its initial efficiency after 1500 h of operation at the maximum power point (MPP). Furthermore, 5 × 5 cm2 perovskite mini-modules are presented, achieving an active-area efficiency of 22.28%. In addition, the quantum well structure in the 2D perovskite capping layer increases the moisture resistance, suppresses ion migration, and improves PSCs' structural and environmental stability.

Fluorescent Conversion Agent Embedded in Zinc Oxide as an Electron-Transporting Layer for High-Performance Non-Fullerene Organic Solar Cells with Improved Photostability.

Zinc oxide (ZnO) is widely used as an electron transporting layer (ETL) for organic solar cells (OSCs). Here, a low-cost commercial water/alcohol-soluble fluorescent conversion agent, sodium 2,2'-([1,1'-biphenyl]-4,4'-diyldivinylene)-bis(benzenesulfonate) (CBS), is incorporated into ZnO to develop a novel organic-inorganic hybrid ETL for high-performance OSCs. The photoinduced charge transfer from CBS to ZnO significantly improves the charge transport properties of ZnO, resulting in faster electron extraction and reduced charge recombination in OSC devices with ZnO:CBS ETLs. ZnO:CBS-based devices exhibit higher power conversion efficiencies (PCEs) than their pure ZnO-based counterparts, especially in devices with a thicker ETL, which is more suitable for roll-to-roll and large-area module processing. Furthermore, the strong ultraviolet-light absorption capability of CBS inhibits the photodegradation of the active layer, improving the photostability of ZnO:CBS based OSC devices. Therefore, this work provides a simple and effective strategy for realizing high-performance OSCs with high PCE and good photostability, which can further facilitate the commercialization of OSCs.

Renewed Prospects for Organic Photovoltaics.

Organic photovoltaics (OPVs) have progressed steadily through three stages of photoactive materials development: (i) use of poly(3-hexylthiophene) and fullerene-based acceptors (FAs) for optimizing bulk heterojunctions; (ii) development of new donors to better match with FAs; (iii) development of non-fullerene acceptors (NFAs). The development and application of NFAs with an A-D-A configuration (where A = acceptor and D = donor) has enabled devices to have efficient charge generation and small energy losses (Eloss < 0.6 eV), resulting in substantially higher power conversion efficiencies (PCEs) than FA-based devices. The discovery of Y6-type acceptors (Y6 = 2,2'-((2Z,2'Z)-((12,13-bis(2-ethylhexyl)-3,9-diundecyl-12,13-dihydro-[1,2,5]-thiadiazolo[3,4-e]-thieno[2″,3″:4',5']thieno-[2',3':4,5]pyrrolo-[3,2-g]thieno-[2',3':4,5]thieno-[3,2-b]indole-2,10-diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile) with an A-DA' D-A configuration has further propelled the PCEs to go beyond 15% due to smaller Eloss values (∼0.5 eV) and higher external quantum efficiencies. Subsequently, the PCEs of Y6-series single-junction devices have increased to >19% and may soon approach 20%. This review provides an update of recent progress of OPV in the following aspects: developments of novel NFAs and donors, understanding of the structure-property relationships and underlying mechanisms of state-of-the-art OPVs, and tasks underpinning the commercialization of OPVs, such as device stability, module development, potential applications, and high-throughput manufacturing. Finally, an outlook and prospects section summarizes the remaining challenges for the further development of OPV technology.

Deciphering the Roles of MA-Based Volatile Additives for α-FAPbI3 to Enable Efficient Inverted Perovskite Solar Cells.

Functional additives that can interact with the perovskite precursors to form the intermediate phase have been proven essential in obtaining uniform and stable α-FAPbI3 films. Among them, Cl-based volatile additives are the most prevalent in the literature. However, their exact role is still unclear, especially in inverted perovskite solar cells (PSCs). In this work, we have systematically studied the functions of Cl-based volatile additives and MA-based additives in formamidinium lead iodide (FAPbI3)-based inverted PSCs. Using in situ photoluminescence, we provide clear evidence to unravel the different roles of volatile additives (NH4Cl, FACl, and MACl) and MA-based additives (MACl, MABr, and MAI) in the nucleation, crystallization, and phase transition of FAPbI3. Three different kinds of crystallization routes are proposed based on the above additives. The non-MA volatile additives (NH4Cl and FACl) were found to promote crystallization and lower the phase-transition temperatures. The MA-based additives could quickly induce MA-rich nuclei to form pure α-phase FAPbI3 and dramatically reduce phase-transition temperatures. Furthermore, volatile MACl provides a unique effect on promoting the growth of secondary crystallization during annealing. The optimized solar cells with MACl can achieve an efficiency of 23.1%, which is the highest in inverted FAPbI3-based PSCs.

Correlation of Local Isomerization Induced Lateral and Terminal Torsions with Performance and Stability of Organic Photovoltaics.

Organic photovoltaics (OPVs) have achieved great progress in recent years due to delicately designed non-fullerene acceptors (NFAs). Compared with tailoring of the aromatic heterocycles on the NFA backbone, the incorporation of conjugated side-groups is a cost-effective way to improve the photoelectrical properties of NFAs. However, the modifications of side-groups also need to consider their effects on device stability since the molecular planarity changes induced by side-groups are related to the NFA aggregation and the evolution of the blend morphology under stresses. Herein, a new class of NFAs with local-isomerized conjugated side-groups are developed and the impact of local isomerization on their geometries and device performance/stability are systematically investigated. The device based on one of the isomers with balanced side- and terminal-group torsion angles can deliver an impressive power conversion efficiency (PCE) of 18.5%, with a low energy loss (0.528 V) and an excellent photo- and thermal stability. A similar approach can also be applied to another polymer donor to achieve an even higher PCE of 18.8%, which is among the highest efficiencies obtained for binary OPVs. This work demonstrates the effectiveness of applying local isomerization to fine-tune the side-group steric effect and non-covalent interactions between side-group and backbone, therefore improving both photovoltaic performance and stability of fused ring NFA-based OPVs.

Elucidating the Role of Antisolvents on the Surface Chemistry and Optoelectronic Properties of CsPbBrxI3-x Perovskite Nanocrystals.

Colloidal lead-halide perovskite nanocrystals (LHP NCs) have emerged over the past decade as leading candidates for efficient next-generation optoelectronic devices, but their properties and performance critically depend on how they are purified. While antisolvents are widely used for purification, a detailed understanding of how the polarity of the antisolvent influences the surface chemistry and composition of the NCs is missing in the field. Here, we fill this knowledge gap by studying the surface chemistry of purified CsPbBrxI3-x NCs as the model system, which in itself is considered a promising candidate for pure-red light-emitting diodes and top-cells for tandem photovoltaics. Interestingly, we find that as the polarity of the antisolvent increases (from methyl acetate to acetone to butanol), there is a blueshift in the photoluminescence (PL) peak of the NCs along with a decrease in PL quantum yield (PLQY). Through transmission electron microscopy and X-ray photoemission spectroscopy measurements, we find that these changes in PL properties arise from antisolvent-induced iodide removal, which leads to a change in halide composition and, thus, the bandgap. Using detailed nuclear magnetic resonance (NMR) and Fourier-transform infrared spectroscopy (FTIR) measurements along with density functional theory calculations, we propose that more polar antisolvents favor the detachment of the oleic acid and oleylamine ligands, which undergo amide condensation reactions, leading to the removal of iodide anions from the NC surface bound to these ligands. This work shows that careful selection of low-polarity antisolvents is a critical part of designing the synthesis of NCs to achieve high PLQYs with minimal defect-mediated phase segregation.

Stepwise on-surface synthesis of thiophene-based polymeric ribbons by coupling reactions and the carbon-fluorine bond cleavage.

The rational synthesis of thiophene-based cross-coupled polymers on surfaces has been attracting more attention recently. Here, we report the stepwise activation of 5,5'-(2,3-difluoro-1,4-phenylene)bis(2-bromothiophene) as a precursor to synthesize thiophene-based polymeric ribbons on the Au(111) surface. Scanning tunneling microscopy studies showed that the precursor adopted different conformations in the self-assembled structure, organometallic species, and covalent polymers. On annealing the sample at a relatively low temperature (150 °C), the conversion of the organometallic structure into a covalent product with straight lines was observed, in which the Br adatoms arranged between the neighboring chains. On further annealing the sample at 270 °C, the detached Br adatoms played a key role in promoting the C-H bond activation. The cross-linked polymer was achieved by a combination of Ullmann and dehydrogenative coupling. When the annealing temperature was up to 390 °C, the C-F bond activation was triggered, which led to the formation of polymeric ribbons resulting from the cyclodehydrogenation of the fluorinated polymer. This study further supplements the reaction mechanism of thiophene-based dehalogenative, dehydrogenative and defluorinative coupling, and provides us a rational way for synthesizing cross-linked functional materials.

Materials, photophysics and device engineering of perovskite light-emitting diodes.

Here we provide a comprehensive review of a newly developed lighting technology based on metal halide perovskites (i.e. perovskite light-emitting diodes) encompassing the research endeavours into materials, photophysics and device engineering. At the outset we survey the basic perovskite structures and their various dimensions (namely three-, two- and zero-dimensional perovskites), and demonstrate how the compositional engineering of these structures affects the perovskite light-emitting properties. Next, we turn to the physics underpinning photo- and electroluminescence in these materials through their connection to the fundamental excited states, energy/charge transport processes and radiative and non-radiative decay mechanisms. In the remainder of the review, we focus on the engineering of perovskite light-emitting diodes, including the history of their development as well as an extensive analysis of contemporary strategies for boosting device performance. Key concepts include balancing the electron/hole injection, suppression of parasitic carrier losses, improvement of the photoluminescence quantum yield and enhancement of the light extraction. Overall, this review reflects the current paradigm for perovskite lighting, and is intended to serve as a foundation to materials and device scientists newly working in this field.

Architecturing 1D-2D-3D Multidimensional Coupled CsPbI2 Br Perovskites toward Highly Effective and Stable Solar Cells.

Despite the rapid development of CsPbIx Br3- x (0 ≤ x ≤ 3) inorganic perovskite solar cells, associated with their superior thermal stability, their low moisture stability limits their commercial deployment. In this study, 1D-2D-3D multidimensional coupled perovskites are prepared by means of an in situ self-integration approach. This pioneering method allows incorporating thus far unreported 1D-Tpy2 Pb3 I6 and 2D-TpyPb3 I6 (Tpy; terpyridine) perovskites. Heterojunction perovskites demonstrate superior stability against water in comparison with control 3D CsPbI2 Br, which is related to the hydrophobicity of low-dimension (LD) perovskites. Remarkably, the spontaneous involvement of LD perovskites can adjust/reconstruct the interfacial structure. This modification allows releasing the residual strain, establishing effective charge transfer channels that increase the carrier transport ability. Accordingly, 1D-2D-3D hybrid CsPbI2 Br perovskite solar cells demonstrate a stabilized power conversion efficiency as high as 16.1%, which represents a very significant improvement, by a factor of 43%, with respect to control 3D CsPbI2 Br perovskite solar cell. Equally importantly, the multidimensional coupled perovskite solar cells exhibit extraordinary stability, well above 1000 h in ambient atmosphere.

Performance optimization of tandem organic solar cells at varying incident angles based on optical analysis method.

Tandem organic solar cells (OSCs) show great potential due to advantages such as the utilization of wide-spectrum light and low thermalization loss. The current mismatch between sub-cells is one of the major issues reducing the final output efficiency of a tandem device. In this paper, we focus on the current mismatch of tandem OSCs at oblique incidence and aim to reduce its adverse effect on the performances of realistic devices working at varying incident angle. Firstly, we propose an optical analysis method based on the 4×4 matrix formalism to analyze and optimize the performance of tandem solar cells at arbitrary incident angles. Compared with those optimal designs via matching the currents of sub-cells only at normal incidence, the proposed method chooses the optimal structure of the tandem device by maximizing the generated energy density per day with considering the current match at different incident angles during daytime. With the proposed method, a typical tandem organic solar cell is optimized as an example, and the optimized tandem device has a balanced current match at all incident angles during a whole day. Experimental results demonstrate that the generated energy density per day of the optimized tandem device has increased by 4.9% compared to the conventional device optimized only at normal incidence. The proposed method and results are expected to provide some new insights for the performance analysis and optimization of tandem or multi-junction solar cells, especially those devices exhibiting serious current mismatch between sub-cells at varying incident angles in practical applications.

Roll-to-roll printed high voltage supercapattery in lead-contaminated aqueous electrolyte.

This work investigated the potential application of roll-to-roll printed PEDOT:PSS on an ITO/PET substrate using Pb2+ containing 0.1 M NaCl aqueous solution for a supercapattery. The PEDOT:PSS/ITO/PET electrode achieved 2.2 µAh cm-2 (46.5 mAh g-1) in 0.1 M NaCl and 10 µAh cm-2 (216.8 mAh g-1) in 2 mM Pb2+/0.1 M NaCl at a current density of 0.2 mA cm-2 (4.34 A g-1). The electrode also shows good cyclic performance that retains 63% of its initial capacitance after 1000 charge-discharge cycles. A device operating at a high voltage of 1.8 V was built using PEDOT:PSS/ITO/PET in aqueous electrolyte. The energy density of the symmetric PEDOT:PSS/ITO/PET device is 6.2 Wh kg-1 in 0.1 M NaCl and is improved to 11 Wh kg-1 in 3 mM Pb2+/0.1 M NaCl.

The role of spin in the kinetic control of recombination in organic photovoltaics.

In biological complexes, cascade structures promote the spatial separation of photogenerated electrons and holes, preventing their recombination. In contrast, the photogenerated excitons in organic photovoltaic cells are dissociated at a single donor-acceptor heterojunction formed within a de-mixed blend of the donor and acceptor semiconductors. The nanoscale morphology and high charge densities give a high rate of electron-hole encounters, which should in principle result in the formation of spin-triplet excitons, as in organic light-emitting diodes. Although organic photovoltaic cells would have poor quantum efficiencies if every encounter led to recombination, state-of-the-art examples nevertheless demonstrate near-unity quantum efficiency. Here we show that this suppression of recombination arises through the interplay between spin, energetics and delocalization of electronic excitations in organic semiconductors. We use time-resolved spectroscopy to study a series of model high-efficiency polymer-fullerene systems in which the lowest-energy molecular triplet exciton (T1) for the polymer is lower in energy than the intermolecular charge transfer state. We observe the formation of T1 states following bimolecular recombination, indicating that encounters of spin-uncorrelated electrons and holes generate charge transfer states with both spin-singlet ((1)CT) and spin-triplet ((3)CT) characters. We show that the formation of triplet excitons can be the main loss mechanism in organic photovoltaic cells. But we also find that, even when energetically favoured, the relaxation of (3)CT states to T1 states can be strongly suppressed by wavefunction delocalization, allowing for the dissociation of (3)CT states back to free charges, thereby reducing recombination and enhancing device performance. Our results point towards new design rules both for photoconversion systems, enabling the suppression of electron-hole recombination, and for organic light-emitting diodes, avoiding the formation of triplet excitons and enhancing fluorescence efficiency.

Dopant-Free Squaraine-Based Polymeric Hole-Transporting Materials with Comprehensive Passivation Effects for Efficient All-Inorganic Perovskite Solar Cells.

Development of high-performance dopant-free hole-transporting materials (HTMs) with comprehensive passivation effects is highly desirable for all-inorganic perovskite solar cells (PVSCs). Squaraines (SQs) could be a candidate for dopant-free HTMs as they are natural passivators for perovskites. One major limitation of SQs is their relatively low hole mobility. Herein we demonstrate that polymerizing SQs into pseudo two dimensional (2D) p-π conjugated polymers could overcome this problem. By rationally using N,N-diarylanilinosquaraines as the comonomers, the resulting polysquaraine HTMs not only exhibit suitable energy levels and efficient passivation effects, but also achieve very high hole mobility close to 0.01 cm-2 V-1 s-1 . Thus as dopant-free HTMs for α-CsPbI2 Br-based all-inorganic PVSCs, the best PCE reached is 15.5 %, outperforming those of the doped-Spiro-OMeTAD (14.4 %) based control devices and among the best for all-inorganic PVSCs.

n-Type Water/Alcohol-Soluble Naphthalene Diimide-Based Conjugated Polymers for High-Performance Polymer Solar Cells.

With the demonstration of small-area, single-junction polymer solar cells (PSCs) with power conversion efficiencies (PCEs) over the 10% performance milestone, the manufacturing of high-performance large-area PSC modules is becoming the most critical issue for commercial applications. However, materials and processes that are optimized for fabricating small-area devices may not be applicable for the production of high-performance large-area PSC modules. One of the challenges is to develop new conductive interfacial materials that can be easily processed with a wide range of thicknesses without significantly affecting the performance of the PSCs. Toward this goal, we report two novel naphthalene diimide-based, self-doped, n-type water/alcohol-soluble conjugated polymers (WSCPs) that can be processed with a broad thickness range of 5 to 100 nm as efficient electron transporting layers (ETLs) for high-performance PSCs. Space charge limited current and electron spin resonance spectroscopy studies confirm that the presence of amine or ammonium bromide groups on the side chains of the WSCP can n-dope PC71BM at the bulk heterojunction (BHJ)/ETL interface, which improves the electron extraction properties at the cathode. In addition, both amino functional groups can induce self-doping to the WSCPs, although by different doping mechanisms, which leads to highly conductive ETLs with reduced ohmic loss for electron transport and extraction. Ultimately, PSCs based on the self-doped WSCP ETLs exhibit significantly improved device performance, yielding PCEs as high as 9.7% and 10.11% for PTB7-Th/PC71BM and PffBT4T-2OD/PC71BM systems, respectively. More importantly, with PffBT4T-2OD/PC71BM BHJ as an active layer, a prominent PCE of over 8% was achieved even when a thick ETL of 100 nm was used. To the best of our knowledge, this is the highest efficiency demonstrated for PSCs with a thick interlayer and light-harvesting layer, which are important criteria for eventually making organic photovoltaic modules based on roll-to-roll coating processes.

Phosphonium Halides as Both Processing Additives and Interfacial Modifiers for High Performance Planar-Heterojunction Perovskite Solar Cells.

Organic halide salts are successfully incorporated in perovskite-based planar-heterojunction solar cells as both the processing additive and interfacial modifier to improve the morphology of the perovskite light-absorbing layer and the charge collecting property of the cathode. As a result, perovskite solar cells exhibit a significant improvement in power conversion efficiency (PCE) from 10% of the reference device to 13% of the modified devices.

High-performance perovskite-polymer hybrid solar cells via electronic coupling with fullerene monolayers.

A plethora of solution-processed materials have been developed for solar cell applications. Hybrid solar cells based on light absorbing semiconducting polymers infiltrated into mesoporous TiO2 are an interesting concept, but generating charge at the polymer-metal oxide heterojunction is challenging. Metal-organic perovskite absorbers have recently shown remarkable efficiencies but currently lack the range of color tunability of organics. Here, we have combined a fullerene self-assembled monolayer (C60SAM) functionalized mesoporous titania, a perovskite absorber (CH3NH3PbI3-xClx), and a light absorbing polymer hole-conductor, P3HT, to realize a 6.7% efficient hybrid solar cell. We find that photoexcitations in both the perovskite and the polymer undergo very efficient electron transfer to the C60SAM. The C60SAM acts as an electron acceptor but inhibits further electron transfer into the TiO2 mesostructure due to energy level misalignment and poor electronic coupling. Thermalized electrons from the C60SAM are then transported through the perovskite phase. This strategy allows a reduction of energy loss, while still employing a "mesoporous electron acceptor", representing an exciting and versatile route forward for hybrid photovoltaics incorporating light-absorbing polymers. Finally, we show that we can use the C60SAM functionalization of mesoporous TiO2 to achieve an 11.7% perovskite-sensitized solar cell using Spiro-OMeTAD as a transparent hole transporter.

Endothermic Charge Separation Occurs Spontaneously in Non-Fullerene Acceptor/Polymer Bulk Heterojunction.

Organic photovoltaics (OPVs) based on non-fullerene acceptors (NFAs) have achieved a power conversion efficiency close to 20%. These NFA OPVs can generate free carriers efficiently despite a very small energy level offset at the donor/acceptor interface. Why these NFAs can enable efficient charge separation (CS) with low energy losses remains an open question. Here, the CS process in the PM6:Y6 bulk heterojunction is probed by time-resolved two-photon photoemission spectroscopy. It is found that the CS, the conversion from bound charge transfer (CT) excitons to free carriers, is an endothermic process with an enthalpy barrier of 0.15 eV. The CS can occur spontaneously despite being an endothermic process, which implies that it is driven by entropy. It is further argued that the morphology of the PM6:Y6 film and the anisotropic electron delocalization restrict the electron and hole wavefunctions within the CT exciton such that they can primarily contact each other through point-like junctions. This configuration can maximize the entropic driving force.

Mask-inspired moisture-transmitting and durable thermochromic perovskite smart windows.

Thermochromic perovskite smart windows (TPWs) are a cutting-edge energy-efficient window technology. However, like most perovskite-based devices, humidity-related degradation limits their widespread application. Herein, inspired by the structure of medical masks, a unique triple-layer thermochromic perovskite window (MTPW) that enable sufficient water vapor transmission to trigger the thermochromism but effectively repel detrimental water and moisture to extend its lifespan is developed. The MTPW demonstrates superhydrophobicity and maintains a solar modulation ability above 20% during a 45-day aging test, with a decay rate 37 times lower than that of a pristine TPW. It can also immobilize lead ions and significantly reduce lead leakage by 66 times. Furthermore, a significant haze reduction from 90% to 30% is achieved, overcoming the blurriness problem of TPWs. Benefiting from the improved optical performance, extended lifespan, suppressed lead leakage, and facile fabrication, the MTPW pushes forward the wide applications of smart windows in green buildings.

Assessing intra- and inter-molecular charge transfer excitations in non-fullerene acceptors using electroabsorption spectroscopy.

Organic photovoltaic cells using Y6 non-fullerene acceptors have recently achieved high efficiency, and it was suggested to be attributed to the charge-transfer (CT) nature of the excitations in Y6 aggregates. Here, by combining electroabsorption spectroscopy measurements and electronic-structure calculations, we find that the charge-transfer character already exists in isolated Y6 molecules but is strongly increased when there is molecular aggregation. Surprisingly, it is found that the large enhanced charge transfer in clustered Y6 molecules is not due to an increase in excited-state dipole moment, Δµ, as observed in other organic systems, but due to a reduced polarizability change, Δp. It is proposed that such a strong charge-transfer character is promoted by the stabilization of the charge-transfer energy upon aggregation, as deduced from density functional theory and four-state model calculations. This work provides insight into the correlation between molecular electronic properties and charge-transfer characteristics in organic electronic materials.