Semiconducting 2D Copper(I) Iodide Coordination Polymer as a Potential Chemiresistive Sensor for Methanol.

The development of a cost-effective, ultra-selective, and room temperature gas sensor is the need of an hour, owing to the rapid industrialization. Here, a new 2D semiconducting Cu(I) coordination polymer (CP) with 1,4-di(1H-1,2,4-triazol-1-yl)benzene (1,4-TzB) ligand is reported. The CP1 consists of a Cu2I2 secondary building unit bridged by 1,4-TzB, and has high stability as well as semiconducting properties. The chemiresistive sensor, developed by a facile drop-casting method derived from CP1, demonstrates a response value of 66.7 at 100 ppm on methanol exposure, accompanied by swift transient (response and recovery time 17.5 and 34.2 s, respectively) behavior. In addition, the developed sensor displays ultra-high selectivity toward methanol over other volatile organic compounds , boasting LOD and LOQ values of 1.22 and 4.02 ppb, respectively. The CP is found to be a state-of-the-art chemiresistive sensor with ultra-high sensitivity and selectivity toward methanol at room temperature.

Fabrication and Characterization of a Micro Methanol Sensor Using the CMOS-MEMS Technique.

A methanol microsensor integrated with a micro heater manufactured using the complementary metal oxide semiconductor (CMOS)-microelectromechanical system (MEMS) technique was presented. The sensor has a capability of detecting low concentration methanol gas. Structure of the sensor is composed of interdigitated electrodes, a sensitive film and a heater. The heater located under the interdigitated electrodes is utilized to provide a working temperature to the sensitive film. The sensitive film prepared by the sol-gel method is tin dioxide doped cadmium sulfide, which is deposited on the interdigitated electrodes. To obtain the suspended structure and deposit the sensitive film, the sensor needs a post-CMOS process to etch the sacrificial silicon dioxide layer and silicon substrate. The methanol senor is a resistive type. A readout circuit converts the resistance variation of the sensor into the output voltage. The experimental results show that the methanol sensor has a sensitivity of 0.18 V/ppm.

Metal-Organic Framework Based Triboelectric Nanogenerator for a Self-Powered Methanol Sensor with High Sensitivity and Selectivity.

Triboelectric nanogenerators have shown great potential in the area of self-powered gas sensors in the past decade. In this paper, we developed a triboelectric nanogenerator (TENG) based on spiky structured ZIF-8@ZnO, which can harvest energy with high efficiency and act as a self-powered methanol sensor. The open-circuit voltage and short-circuit current generated by a ZIF-8@ZnO-based TENG is 58 V and 10 µA, achieving 2.4 times and 3.3 times enhancement compared to ZnO-based TENGs. The TENG can charge capacitors fast and light up at least 40 LEDs. ZIF-8@ZnO-based TENGs show good sensitivity and selectivity to methanol gas at room temperature due to the porous structure provided by ZIF-8 and the heterostructure of ZIF-8@ZnO. The response of ZIF-8@ZnO-based TENG to methanol reaches 30.35% at 100 ppm with excellent response (∼5.9 s) and recovery time (∼2.2 s). This work demonstrates the application of MOF-modified metal oxide semiconductors based on a self-powered gas sensor and proposes a promising solution to enhance the output performance and sensing properties of TENGs based on metal oxide semiconductors.

A conductometric enzymatic methanol sensor based on polystyrene - PAMAM dendritic polymer electrospun nanofibers.

Methanol (MeOH) is a solvent and cleaning agent used in industry, but it is poisonous when ingested. The recommended release threshold for MeOH vapor is 200 ppm. We present a novel sensitive micro-conductometric MeOH biosensor created by grafting alcohol oxidase (AOX) onto electrospun polystyrene-poly(amidoamine) dendritic polymer blend nanofibers (PS-PAMAM-ESNFs) on interdigitated electrodes (IDEs). The analytical performance of the MeOH microsensor was evaluated using gaseous MeOH, ethanol, and acetone samples collected from the headspace above aqueous solution with known concentration. The sensor's response time (tRes) fluctuates from 13 s to 35 s from lower to higher concentrations. The conductometric sensor has a sensitivity of 150.53 µS.cm-1 (v/v) for MeOH and a detection limit of 100 ppm in the gas phase. The MeOH sensor is 7.3 times less sensitive to ethanol and 136.8 times less sensitive to acetone. The sensor was verified for detecting MeOH in commercial rubbing alcohol samples.

Tuning the sensing responses towards room-temperature hypersensitive methanol gas sensor using exfoliated graphene-enhanced ZnO quantum dot nanostructures.

A suitable and non-invasive methanol sensor workable in ambient temperature conditions with a high response has gained wide interest to prevent detrimental consequences for industrial workers from its low-level intoxication. In this work, we present a tunable and highly responsive ppb-level methanol gas sensor device working at room temperature via a bottom-up synthetic approach using exfoliated graphene sheet (EGs) and ZnO quantum dots (QDs) on an aluminum anodic oxide (AAO) template. It is verified that EGs-supported AAO with a vertical electrode configuration enabled high and fast-responsive methanol sensing. Moreover, the hydroxyl and carboxyl groups of the high surface area EGs and ZnO QDs with a 3.37 eV bandgap efficiently absorbing UV light led to 56 times high response due to the enhanced polarization on the sensor surface compared to non-UV-radiated EGs/AAO at 800 ppb of methanol. The optimal resonance frequency of methanol is determined to be 100 kHz, which could detect methanol with high response of 2.65% at 100 ppm. The limit of detection (LOD) concentration is obtained at 2 ppb level. This study demonstrates the potential of UV-assisted ZnO, EGs, and AAO-based capacitance sensor material for rapidly detecting hazardous gaseous light organic molecules at ambient conditions, and the overall approach can be easily expanded to a novel non-invasive monitoring strategy for light and hazardous volatile organic exposures.

Cellulose nanocrystal and ß-cyclodextrin chiral nematic composite films as selective sensor for methanol discrimination.

Due to the serious threat of methanol to human health, the convenient, quick and specific detection of methanol is of great importance. Therefore, in this study, a biomass-derived chiral nematic composite film is fabricated by the co-evaporation of cellulose nanocrystals (CNC) and water-soluble polymer of ß-cyclodextrin (PCD). The freestanding iridescent CNC-PCD film shows distinguishing structural colors of red and yellow green for methanol and ethanol respectively, realizing the identification of the two homologous alcohols by naked eyes. Besides, the quick, reversible and quantitative colorimetric sensing of the CNC-PCD film to methanol is verified. As its structural color and maximum reflection wavelength redshift to the greatest extent for methanol than other alcohols, the CNC-PCD film exhibits the specificity and selectivity for methanol detection in both single and mixed solvents. Such less-consumed and easy-to-handle CNC-PCD film may be useful as a colorimetric sensor to detect or discriminate methanol in some industrial products.

A sensor of liquid methanol for direct methanol fuel cells.

The methanol sensors are of significance to maintain the efficient and stable operation of direct methanol fuel cells (DMFCs). The issues, including stability, the relationship between temperature, current density and concentration need, however, urgent attention. A novel electrochemical methanol sensor which is based on current output limited by methanol diffusion is developed. The stability of sensors was lifted steeply through introducing a reference electrode, narrowing the methanol flow channel, and adding a water container. The relationship between the temperature, response current and methanol concentration was determined with the help of theoretical derivation and the validity was verified by the fitting result. Other sensors can avail of this relationship to correct the temperature effect. Application test indicated that the sensor may be of great potential for the accurate monitoring of methanol concentration at the levels of DMFCs application.

Development of Methanol Sensor Based on Sol-Gel Drop-Coating Co3O4·CdO·ZnO Nanoparticles Modified Gold-Coated µ-Chip by Electro-Oxidation Process.

Herein, novel Co3O4·CdO·ZnO-based tri-metallic oxide nanoparticles (CCZ) were synthesized by a simple solution method in basic phase. We have used Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Field Emission Scanning Electron Microscope (FESEM), Dynamic Light Scattering (DLS), Tunneling Electron Microscopy (TEM), and Energy-Dispersive Spectroscopy (EDS) techniques to characterize the CCZ nanoparticles. XRD, TEM, DLS, and FESEM investigations have confirmed the tri-metallic nanoparticles' structure, while XPS and EDS analyses have shown the elemental compositions of the CCZ nanoparticles. Later, a Au/µ-Chip was modified with the CCZ nanoparticles using a conducting binder, PEDOT: PSS (poly(3,4-ethylenedioxythiophene) polystyrene sulfonate) in a sol-gel system, and dried completely in air. Then, the CCZ/Au/µ-Chip sensor was used to detect methanol (MeOH) in phosphate buffer solution (PBS). Outstanding sensing performance was achieved for the CCZ/Au/µ-Chip sensor, such as excellent sensitivity (1.3842 µAµM-1cm-2), a wide linear dynamic range of 1.0 nM-2.0 mM (R2 = 0.9992), an ultra-low detection limit (32.8 ± 0.1 pM at S/N = 3), a fast response time (~11 s), and excellent reproducibility and repeatability. This CCZ/Au/µ-Chip sensor was further applied with appropriate quantification results in real environmental sample analyses.

Facile Wearable Vapor/Liquid Amphibious Methanol Sensor.

Detection of methanol is a significant segment for body health and work safety in the production of chemical industry. However, there hardly exists highly selective methanol detection system with green environment for vapor or liquid adaptability, as well as large linear relationship. A facile wearable vapor/liquid amphibious electrochemical sensor for monitoring methanol has been carried out for the first time in this Article. This wearable methanol sensor was fabricated by using a simple screen-printing technology for accomplishing a microdevice platform, showing good linear relationship, high selectivity (multiple volatile chemical compounds), reliable repeatability, good stability, and excellent stretching and bending performance (nitrile glove-based sensor) without pretreatment or adding any polymers into inks. Owing to its good environmental adaptability of vapor or liquid and various sensing behaviors (high sensitivity and wide linear range) by being modified with different content of platinum catalyst, this methanol sensor would have tremendous potential application for environmental monitoring on smart wearable devices when employed based on various platforms (such as PET, cotton, and nitrile gloves).

Detection of Methanol with Fast Response by Monodispersed Indium Tungsten Oxide Ellipsoidal Nanospheres.

Indium tungsten oxide ellipsoidal nanospheres were prepared with different In/W ratios by using a simple hydrothermal method without any surfactant for the first time. Sensors based on different In/W ratios samples were fabricated, and one of the samples exhibited better response to methanol compared with others. High content of defective oxygen (Ov) and proper output proportion of In to W might be the main reasons for the better gas sensing properties. The length of the nanosphere was about 150-200 nm, and the width was about 100 nm. Various techniques were applied to investigate the nanospheres. Sensing characteristics toward methanol were investigated. Significantly, the sensor exhibited ultrafast response to methanol. The response time to 400 ppm methanol was no more than 2 s and the recovery time was 9 s at 312 °C. Most importantly, the humidity almost had no effect on the response of the sensor fabricated here, which is hard to achieve in gas-sensing applications.