Low Parts Per Trillion Detection of Iodinated Disinfection Byproducts in Drinking Water and Urine using Vacuum-Assisted Sorbent Extraction and GC-MS/MS.

Disinfection byproducts (DBPs) are ubiquitous environmental contaminants, which are present in virtually all drinking water and linked to detrimental health effects. Iodinated-DBPs are more cytotoxic and genotoxic than chloro- and bromo-DBPs and are formed during disinfection of iodide-containing source water. Liquid-liquid extraction (LLE) paired with gas chromatography (GC)-mass spectrometry (MS) has been the method of choice in the study of low molecular weight iodinated-DBPs; however, this method is laborious and time-consuming and struggles with complex matrices. We developed an environmentally friendly method utilizing headspace solid phase extraction with the application of vacuum to measure six iodinated-trihalomethanes (I-THMs) in drinking water and urine. Vacuum-assisted sorbent extraction (VASE) has the ability to exhaustively and rapidly extract volatile and semivolatile compounds from liquid matrices without the use of solvent. Using VASE with GC-MS/MS provides improved analyte recovery and reduced matrix interference compared to LLE. Additionally, VASE enables extraction of 30 samples simultaneously with minimal sample handling and improved method reproducibility. Using VASE with GC-MS/MS, we achieved quantification limits of 3-4 ng/L. This technique was demonstrated on drinking water from four cities, where five I-THMs were quantified at levels 10-33 times below comparable LLE methods with 10 times lower volumes of sample (10 mL vs 100 mL).

The insightful water quality analysis and predictive model establishment via machine learning in dual-source drinking water distribution system.

Dual-source drinking water distribution systems (DWDS) over single-source water supply systems are becoming more practical in providing water for megacities. However, the more complex water supply problems are also generated, especially at the hydraulic junction. Herein, we have sampled for a one-year and analyzed the water quality at the hydraulic junction of a dual-source DWDS. The results show that visible changes in drinking water quality, including turbidity, pH, UV254, DOC, residual chlorine, and trihalomethanes (TMHs), are observed at the sample point between 10 and 12 km to one drinking water plant. The average concentration of residual chlorine decreases from 0.74 ± 0.05 mg/L to 0.31 ± 0.11 mg/L during the water supplied from 0 to 10 km and then increases to 0.75 ± 0.05 mg/L at the end of 22 km. Whereas the THMs shows an opposite trend, the concentration reaches to a peak level at hydraulic junction area (10-12 km). According to parallel factor (PARAFAC) and high-performance size-exclusion chromatography (HPSEC) analysis, organic matters vary significantly during water distribution, and tryptophan-like substances and amino acids are closely related to the level of THMs. The hydraulic junction area is confirmed to be located at 10-12 km based on the water quality variation. Furthermore, data-driven models are established by machine learning (ML) with test R2 higher than 0.8 for THMs prediction. And the SHAP analysis explains the model results and identifies the positive (water temperature and water supply distance) and negative (residual chlorine and pH) key factors influencing the THMs formation. This study conducts a deep understanding of water quality at the hydraulic junction areas and establishes predictive models for THMs formation in dual-sources DWDS.

Influence of agro-wastes derived biochar and their composite on reducing the mobility of toxic heavy metals and their bioavailability in industrial contaminated soils.

The agro-waste derived valuable products are prime interest for effective management of toxic heavy metals (THMs). The present study investigated the efficacy of biochars (BCs) on immobilization of THMs (Cr, Zn, Pb, Cu, Ni and Cd), bioaccumulation and health risk. Agro-wastes derived BCs including wheat straw biochar (WSB), orange peel biochar (OPB), rice husk biochar (RHB) and their composite biochar (CB) were applied in industrial contaminated soil (ICS) at 1% and 3% amendments rates. All the BCs significantly decreased the bioavailable THMs and significantly (p < 0.001) reduced bioaccumulation at 3% application with highest efficiency for CB followed by OPB, WSB and RHB as compared to control treatment. The bioaccumulation factor (BAF), concentration index (CI) and ecological risk were decreased with all BCs. The hazard quotient (HQ) and hazard index (HI) of all THMs were <1, except Cd, while carcer risk (CR) and total cancer risk index (TCRI) were decreased through all BCs. The overall results depicted that CB at 3% application rate showed higher efficacy to reduce significantly (p < 0.001) the THMs uptake and reduced health risk. Hence, the present study suggests that the composite of BCs prepared from agro-wastes is eco-friendly amendment to reduce THMs in ICS and minimize its subsequent uptake in vegetables.

The present study has a scientific research scope, based on reduction of bioavailability and bioaccumulation of toxic heavy metals (THMs) by the addition of biochars derived from agro-wastes and their composite biochar (CB), thereby decreasing the potential health risk. Limited study has been conducted, especially on the impact of CB in THMs-contaminated soil. This study could fill the scientific research gap and provides useful information for mitigation of THMs present in contaminated soil, which could be followed by the Environmental Protection Agency, Ministry of Agriculture and farmers in degraded lands.

Adsorption kinetics, isotherms, and selectivity of trihalomethanes and haloacetonitriles by granular activated carbon.

The performance capability of granular activated carbon (GAC) adsorption in terms of disinfection by-product (DBPs) removal was investigated with synthetic water containing 1) trihalomethanes (THMs), 2) haloacetronitriles (HANs), and 3) Mix-THMs & HANs. The initial 20 min of adsorption resulted in the maximum adsorption rate, with the total THMs, total HANs, and total Mix-THMs & HANs being 4.972, 2.071, and 6.460 µg/gGAC-min, respectively. GAC dosage affects the adsorption selectivity of THMs and HANs. Under a low GAC dosage, the selectivity of GAC adsorbs more bromo-THMs than chloro-THMs. The adsorption selectivity of THMs on GAC following bromoform > dibromochloromethane > bromodichloromethane > chloroform was investigated. As the GAC concentration increased, the selectivity of THM adsorption by GAC became comparable. Chloro-HAN, in contrast to THMs, has a higher adsorption selectivity than bromo-HAN. Trichloroacetonitrile was removed by GAC more rapidly than the other HAN species when the GAC dose was increased. The toxin of bromoform was primarily eliminated through GAC adsorption, caused by a greater removal rate than that of the other THMs. As an implemented measure, GAC is introduced to reduce THMs and HANs and the toxic contents associated with THMs and HANs.

Using water quality parameters to prediction of the ion-based trihalomethane by an artificial neural network model.

Trihalomethanes (THMs) are the first disinfectant by-products in the drinking water distribution network and are classified as potential carcinogens. The presence of THMs in chlorinated water depends on the pH, water temperature, contact time between water and chlorine, type and dose of disinfection, bromide ion concentration, and type and concentration of natural organic materials (NOMs). In the present study, the formation of THMs was evaluated by six simple and easy water quality parameters and modeled by an artificial neural network (ANN) approach through five water distribution networks (WDNs) and the Karoun River in Khuzestan province. The results of this study that was conducted from October 2014 to September 2015 showed that THM concentration ranged in five WDNs, including Shoushtar, Ahvaz (2), Ahvaz (3), Mahshahr, Khorramshahr, and total WDNs through N.D.-9.39 µg/L, 7.12-28.60, 38.16-67.00, 17.15-90.46, 15.14-29.99, and N.D.-156, respectively. The concentration of THMs exceeded Iran and EPA standards in many cases in Mahshahr and Khorramshahr WDNs. Evaluation of R2, MSE, and RMSE showed the appropriate correlation between measured and modeled THMs, indicating a reasonable ANN potential for estimating THM formation in water sources.

Trihalomethanes in developed and developing countries.

The reactions between natural organic matter, anthropogenic contaminants, ions, and disinfectants lead to the formation of disinfection by-products (DBPs) such as trihalomethanes (THMs) in drinking water. The formation of THMs is strongly related to the chlorination of water. The study's central objective was to compare the concentration of THMs in twenty developed and developing countries and their disinfection techniques. The THM concentration in 11 developed and 9 developing countries ranged from 0.5 µg/L (Germany) to 215 µg/L (Russia) and 3 µg/L (China) to 439.2 µg/L (Bangladesh), respectively. The developed country has partially succeeded in reducing THM concentration in drinking water, whereas significant steps are needed in developing countries to reduce the existing high THM concentration. The concentration of THMs in water varies among these countries because of the different water sources, water quality, environmental conditions, and efficiency of water treatment technologies. A meaningful relationship has been observed between the properties of water and the THM formation. The use of chemical disinfectants will result in new forms of DBPs that are undesirable due to their carcinogenic and mutagenic effects on human health. The DBP guidelines by various national and international agencies have helped to control and manage the THM concentration in drinking water. However, these regulatory standards are not continuously monitored. Therefore, the formation of these compounds should be prevented either by removing THMs forming precursors or by using an integrated approach for controlling THM formation by implementing advanced water treatment technology. Extensive research is desirable in domains like THM minimization strategies which are easy to deploy, scalable, and cost-effective.

Controlling the formation of halogenated byproducts in the chlorination of source waters by oxidative pre-treatment with the Fe(II)/Fe(III)-S(IV)-air system.

Breakpoint chlorination is a generally accepted method for removing ammonium ion from source waters in drinking water treatment technologies. This process is often accompanied by the formation of halogenated organic byproducts. The presence of these compounds in potable water is of primary concern. In this paper, we demonstrate that the concentration of the precursors of the halogenated species can sufficiently be decreased by oxidizing the organic pollutants with the Fe(II)/Fe(III) - S(IV) - air system. Pre-oxidative treatment of the source waters results in a substantial reduction of chemical oxygen demand, while the ammonium ion concentration remains unaffected. The breakpoint chlorination produces substantially less trihalomethanes (THMs) and adsorbable halogenated organic compounds (AOXs) in oxidatively pre-treated source waters than in raw waters. These results offer a possibility to improve drinking water treatment technologies for better controlling the formation of antagonistic byproducts. It is demonstrated that reaching the regulated concentration levels of THMs is feasible with this method even in source waters containing organic pollutants at relatively high concentration levels. The main advantage of the procedure is that the reagents used for the oxidative pre-treatment are converted into non-toxic products (Fe(III) and SO42-) by the end of the process.

Cumulative human health risk analysis of trihalomethanes exposure in drinking water systems.

Chlorinated compounds on reaction with natural organic substances present in water leads to the formation of trihalomethanes (THMs), a major type of disinfection by-products (DBPs). Trihalomethanes (THMs) are the most widely investigated DBPs in drinking water systems because of their carcinogenic potential and subsequent adverse effects on human health. This study investigated the effect of gastro-intestinal absorption factor on human health risk assessment. Monitoring and analysis of water quality parameters and THMs levels in drinking water treatment plants revealed that the average values (306.5 µg/L) exceeded the recommended US EPA guidelines of 80 µg/L. Spearman rank (rho) correlation coefficient indicated that dissolved organic carbon is the major parameter influencing THMs formation. Monte Carlo simulations base risk assessment study was conducted for three different exposure pathways. The observed human health risk exposure effects due to THMs were below the recommended USEPA level (1.0 × 10-6) for both the drinking water treatment plants. Seasonal disparity on risk estimation analysis revealed higher risk in summer season followed by autumn which is principally due to high concentration of THMs in summers.

Insight into the formation of iodinated trihalomethanes during chlorination, monochloramination, and dichloramination of iodide-containing water.

In this study, the formation of iodinated trihalomethanes (I-THMs) was systematically evaluated and compared for three treatment processes - (i) chlorination, (ii) monochloramine, and (iii) dichloramination - under different pH conditions. The results demonstrated that I-THM formation decreased in the order of monochloramination > dichloramination > chlorination in acidic and neutral pH. However, the generation of I-THMs increased in the dichloramination < chlorination < monochloramination order in alkaline condition. Specifically, the formation of I-THMs increased as pH increased from 5 to 9 during chlorination and monochloramination processes, while the maximum I-THM formation occurred at pH 7 during dichloramination. The discrepancy could be mainly related to the stability of the three chlor (am) ine disinfectants at different pH conditions. Moreover, in order to gain a thorough insight into the mechanisms of I-THM formation during dichloramination, further investigation was conducted on the influencing factors of DOC concentration and Br-/I- molar ratio. I-THM formation exhibited an increasing and then decreasing trend as the concentration of DOC increased from 1 to 7 mg-C/L, while the yield of I-THMs increased with increasing Br-/I- molar ratio from 5:0 to 5:10. During the three processes mentioned above, similar I-THM formation results were also obtained in real water, which indicates that the excessive generation of I-THMs should be paid special attention during the disinfection of iodide-containing water.

Prenatal Exposure to Disinfection Byproducts and Intrauterine Growth in a Chinese Cohort.

Disinfection byproduct (DBP) exposure has been associated with birth size, pregnancy oxidative stress, and other adverse perinatal outcomes. However, little is known about the potential effect of prenatal DBP exposure on intrauterine growth. The present study included 1516 pregnant women from the Xiaogan Disinfection By-Products (XGDBP) birth cohort who were measured for four blood trihalomethanes [i.e., chloroform (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), and bromoform (TBM)] and two urinary haloacetic acids [i.e., dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA)] across pregnancy trimesters. Second- and third-trimester fetal ultrasound measures of the abdominal circumference (AC), head circumference, biparietal diameter, femur length, and estimated fetal weight and birth weight were converted into z-scores. After adjusting for potential confounders, linear mixed models showed a decreasing AC z-score across tertiles of blood brominated THM (Br-THMs, the sum of BDCM, DBCM, and TBM) and total THM (THM4, the sum of Br-THMs and TCM) concentrations (both p for trend <0.01). We also observed a decreasing AC z-score across categories of blood TBM during pregnancy trimesters (p for trend = 0.03). Urinary haloacetic acids were unrelated to fetal growth parameters. In summary, prenatal exposure to THMs, particularly during the first trimester, was associated with reduced fetal abdominal circumference.

Investigation into the content and formation of trihalomethanes and molecular change of dissolved organic matter from a typical water plant in south China.

Trihalomethanes (THMs) are a class of disinfection by-products that were proved to have adverse effects to human health. Investigation into its content change and molecular composition variation of its main precursor, which is believed to be dissolved organic matter (DOM) during water purification process, can help understand the formation mechanism of THMs and optimize the processes in drinking water treatment plant (DWTP). This is of great significance to ensure the safety of urban water supply. In this study, detailed changes of THMs' content and formation potential were determined during the water purification process in summer and winter at a typical DWTP in south China. Specific molecular composition changes of DOM were also characterized by ultrahigh-resolution mass spectrometry, to comprehensively study its correlation with the formation of THMs in different water processing units and seasons. The result showed that chlorination will cause drastic changes of water quality and a sharp increase in the concentration of THMs (18.7 times in summer and 13.9 times in winter). Molecular-level characterization of DOM indicates that a range of lignin-like substance with lower O/C (< 0.5) and H/C (< 1.25) vanished and considerable amount of protein-like and tannins-like substance with higher H/C (> 1.25) and O/C (> 0.5) was formed after chlorination. Analysis of Cl-containing products demonstrated that a bulk of CHOCl1 and CHOCl2 compounds with moderate molecular weights were formed in both winter and summer. However, the newly formed CHOCl1 molecules showed a relatively higher mass weight in summer (> 500 Da) compared to winter (300-500 Da). Seasonal differences also emerged in the result of correlation between the trihalomethanes formation potential and total organic carbon. The correlation coefficient in summer (0.500) was lower than that in winter (0.843). The results suggested that the exhaustive reaction and contribution of DOM to THMs may vary in different seasons.

A PNA-DNA2 Triple-Helix Molecular Switch-Based Colorimetric Sensor for Sensitive and Specific Detection of microRNAs from Cancer Cells.

Peptide nucleic acids (PNAs), the synthetic DNA mimics that can bind to oligonucleotides to form duplexes, triplexes, and quadruplexes, could be advantageous as probes for nucleic acid sequences owing to their unique physicochemical and biochemical properties. We have found that a homopurine PNA strand could bind to two homopyrimidine DNA strands to form a PNA-DNA2 triplex. Moreover, the cyanine dye DiSC2 (5) could bind with high affinity to this triplex and cause a noticeable color change. On the basis of this phenomenon, we have designed a label-free colorimetric sensing platform for miRNAs from cancer cells by using a PNA-DNA2 triple-helix molecular switch (THMS) and DiSC2 (5). This sensing platform can detect miRNA-21 specifically with a detection limit of 0.18 nM, which is comparable to that of the THMS-mediated fluorescence sensing platform. Moreover, this colorimetric platform does not involve any chemical modification or enzymatic signal amplification, which boosts its applicability and availability at the point of care in resource-limited settings. The universality of this approach can be simply achieved by altering the sequences of the probe DNA for specific targets.

Comparison of UV-induced AOPs (UV/Cl2, UV/NH2Cl, UV/ClO2 and UV/H2O2 ) in the degradation of iopamidol: Kinetics, energy requirements and DBPs-related toxicity in sequential disinfection processes.

The UV-induced advanced oxidation processes (AOPs, including UV/Cl2, UV/NH2Cl, UV/ClO2 and UV/H2O2 ) degradation kinetics and energy requirements of iopamidol as well as DBPs-related toxicity in sequential disinfection were compared in this study. The photodegradation of iopamidol in these processes can be well described by pseudo-first-order model and the removal efficiency ranked in descending order of UV/Cl2  > UV/H2O2  > UV/NH2Cl > UV/ClO2  > UV. The synergistic effects could be attributed to diverse radical species generated in each system. Influencing factors of oxidant dosage, UV intensity, solution pH and water matrixes (Cl- , NH4 + and nature organic matter) were evaluated in detail. Higher oxidant dosages and greater UV intensities led to bigger pseudo-first-order rate constants (Kobs) in these processes, but the pH behaviors exhibited quite differently. The presence of Cl- , NH4 + and nature organic matter posed different effects on the degradation rate. The parameter of electrical energy per order (EE/O) was adopted to evaluate the energy requirements of the tested systems and it followed the trend of UV/ClO2  > UV > UV/NH2Cl > UV/H2O2  > UV/Cl2 . Pretreatment of iopamidol by UV/Cl2 and UV/NH2Cl clearly enhanced the production of classical disinfection by-products (DBPs) and iodo-trihalomethanes (I-THMs) during subsequent oxidation while UV/ClO2 and UV/H2O2 exhibited almost elimination effect. From the perspective of weighted water toxicity, the risk ranking was UV/NH2Cl > UV/Cl2 > UV > UV/H2O2 > UV/ClO2 . Among the discussed UV-driven AOPs, UV/Cl2 was proved to be the most cost-effective one for iopamidol removal while UV/ClO2 displayed overwhelming advantages in regulating the water toxicity associated with DBPs, especially I-THMs. The present results could provide some insights into the application of UV-activated AOPs technologies in tradeoffs between cost-effectiveness assessment and DBPs-related toxicity control of the disinfected waters containing iopamidol.

Risk associated with increasing bromide in drinking water sources in Yancheng City, China.

The bromide concentration in water source (WS) of Yancheng City in China increased unexpectedly due to industrial discharge and saltwater intrusion, which leads to the formation of trihalomethane (THMs) in finished water of water treatment plants (WTP), especially brominated THMs. In Yancheng City, drinking water is supplied by WTP1 and WTP2, primarily sourced by WS1 and WS2, respectively. In this paper, the seasonal variations of bromide in WS1 and WS2 and THMs species in WTP1 and WTP2 were analyzed and compared. The effects of bromide in WS on THMs formation in finished water of WTP in terms of bromine substitution factor (BSF) were simulated by statistical linear model. Although the THMs concentrations in WTP1 were approximate to that in WTP2, the brominated THMs concentrations in WTP1 were higher than that in WTP2 due to higher bromide concentration in WS1 than WS2. The cancer risk analysis indicated that THMs' species of DBCM is the dominant THMs for WTP1 as well as WTP2, which can provide more information for WTPs with higher bromide concentration in water source.

Regression models evaluating THMs, HAAs and HANs formation upon chloramination of source water collected from Yangtze River Delta Region, China.

Present study aimed to generate multiple regression models to estimate the formation of trihalomethanes (THMs), haloacetonitriles (HANs) and haloacetic acids (HAAs) during chloramination of source water obtained from Yangtze River Delta Region, China. The results showed that the regression models for trichloromethane (TCM), dichloroacetonitrile (DCAN), dichloroacetic acid (DCAA), dihaloacetic acids (DHAAs), 5 HAAs species regulated by U.S. EPA (HAA5) and total haloacetic acids (HAA9) have good evaluation ability (prediction accuracy reached 81-94%), while the models for total haloacetonitriles (HAN4), trichloroacetic acid (TCAA), trihaloacetic acids (THAAs) and total trihalomethanes (THM4), they appeared relative low prediction accuracy (58-72%). For THMs, dissolved organic nitrogen (DON) was their key organic precursor, yet for HAN, DHAAs and THAAs, UVA254 played the dominant role. The other key factors influencing DBP formation included the bromide (THM4, DHAAs and HAA9), reaction time (DCAN, HAN4), chloramine dose (TCM, DCAA, TCAA, HAA5 and THAAs). These results provided important information for water works to optimize the water treatment process to control DBPs, and give an evaluating method for DBPs levels when estimating the health risks related with DBP exposure during chloramination.

Ships' Ballast Water Treatment by Chlorination Can Generate Toxic Trihalomethanes.

The International Maritime Organization (IMO) will enforce a new abundance-based performance standard for ballast water in September, 2017. Strong oxidants, like chlorine, have been proposed as a method for achieving this standard. However chlorine treatment of ballast water can produce hazardous trihalomethanes. We assessed maximum trihalomethane production from one chlorine dose for three types of ballast water (fresh, brackish and marine) and three levels of total organic carbon (TOC) concentration (natural, filtered, enhanced). While the current standard test considers a 5 day voyage, there is a high possibility of shorter trips and sudden change of plans that will release treated waters in the environment. Water source and TOC significantly affected trihalomethane production, with the highest amounts generated in brackish waters and enhanced TOC concentration. The concentration of brominated trihalomethanes increased from background levels and was highest in brackish water, followed by marine and fresh water.

Health risk as a consequence of exposure to trihalomethanes in swimming pool water

The article presents the formation and toxicity of trihalomethanes (THMs), substances belonging to Disinfection ByProducts (DBP), formed as a result of pool water chlorination. Concentration of THMs in pool water has been standardised in Poland since recently. THMs concentration in pool water depends on multiple factors, mostly the method of water disinfection, including chlorine or organic substance (TOC) concentration. Apart from that, the level of exposure of swimmers to the toxic effect of THMs is affected by their content in the air of swimming pool halls, intensity of swimming as well as time of stay in the indoor swimming pool area. The water and air temperature as well as number of swimmers and time of their staying in pool have also significance influence on THMs concentration. In order to decrease the quantity of THMs in pool water, alternative disinfection agents are applied. Additionally, an efficiently operating pool ventilation system as well as proper water treatment method are also important. Because THMs are produced from organic material under the influence of the chlorination, the users can have an impact on decrease of the THMs concentration in pool water, for instance by taking a shower prior to entering the pool or by wearing a swim cap. The results of studies conducted in 2015 showed that the quantity of THMs in pool water depends on type of the pool (indoor, outdoor), water replacement frequency, water treatment system, chlorine dose and TOC content. In most collected samples, the THMs concentration exceeded the admissible norm (100 µg/L).

Environmental and personal determinants of the uptake of disinfection by-products during swimming.

BACKGROUND: Trihalomethanes (THMs) in exhaled breath and trichloroacetic acid (TCAA) in urine are internal dose biomarkers of exposure to disinfection by-products (DBPs) in swimming pools. OBJECTIVE: We assessed how these biomarkers reflect the levels of a battery of DBPs in pool water and trichloramine in air, and evaluated personal determinants. METHODS: A total of 116 adults swam during 40min in a chlorinated indoor pool. We measured chloroform, bromodichloromethane, dibromochloromethane and bromoform in exhaled breath and TCAA in urine before and after swimming, trichloramine in air and several DBPs in water. Personal determinants included sex, age, body mass index (BMI), distance swum, energy expenditure, heart rate and 12 polymorphisms in GSTT1, GSTZ1 and CYP2E1 genes. RESULTS: Median level of exhaled total THMs and creatinine adjusted urine TCAA increased from 0.5 to 14.4µg/m(3) and from 2.5 to 5.8µmol/mol after swimming, respectively. The increase in exhaled brominated THMs was correlated with brominated THMs, haloacetic acids, haloacetonitriles, haloketones, chloramines, total organic carbon and total organic halogen in water and trichloramine in air. Such correlations were not detected for exhaled chloroform, total THMs or urine TCAA. Exhaled THM increased more in men, urine TCAA increased more in women, and both were affected by exercise intensity. Genetic variants were associated with differential increases in exposure biomarkers. CONCLUSION: Our findings suggest that, although affected by sex, physical activity and polymorphisms in key metabolizing enzymes, brominated THMs in exhaled breath could be used as a non-invasive DBP exposure biomarker in swimming pools with bromide-containing source waters. This warrants confirmation with new studies.

Formation of trihalomethanes of dissolved organic matter fractions in reservoir and canal waters.

The formation of trihalomethanes (THMs) of hydrophobic organic fraction (HPO), transphilic organic fraction (TPI), and hydrophilic organic fraction (HPI) of reservoir and canal waters from the U-Tapao River Basin, Songkhla, Thailand was investigated. Water samples were collected three times from two reservoirs, upstream, midstream, and downstream of the U-Tapao canal. The HPO was the major dissolved organic matter (DOM) fraction in reservoir and canal waters. On average, the HPO accounted for 53 and 45% of the DOM in reservoir and canal waters, respectively. The TPI of 19 and 23% in reservoir and canal waters were determined, respectively. The HPI of 29% of the reservoir water and HPI of 32% of the canal water were detected. For the reservoir water, the highest trihalomethane formation potential (THMFP)/dissolved organic carbon (DOC) was determined for the HPI, followed by the TPI and HPO, respectively. The average values of the THMFP/DOC of the HPI, TPI, and HPO of the reservoir water were 78, 52, and 49 µg THMs/mg C, respectively. The highest THMFP/DOC of the canal water was detected for the HPI, followed by HPO and TPI, respectively. Average values of the THMFP/DOC of HPI of water at upstream and midstream locations of 58 µg THMs/mg C and downstream location of 113 µg THMs/mg C were determined. Average values of THMFP/DOC of HPO of water at upstream and midstream and downstream locations were 48 and 93 µg THMs/mg C, respectively. For the lowest THMFP/DOC fraction, the average values of THMFP/DOC of TPI of water at upstream and midstream and downstream locations were 35 and 73 µg THMs/mg C, respectively.

Using regression models to evaluate the formation of trihalomethanes and haloacetonitriles via chlorination of source water with low SUVA values in the Yangtze River Delta region, China.

The purpose of this study was to develop the multiple regression models to evaluate the formation of trihalomethanes (THMs) and haloacetonitriles (HANs) during chlorination of source water with low specific ultraviolet absorbance (SUVA) in Yangtze River Delta, China. The results showed that the regression models of THMs exhibited good accuracy and precision, and 86-97 % of the calculated values fell within ±25 % of the measured values. While the HANs models showed relatively weak evaluation ability, as only 75-83 % of the calculated values were within ±25 % of the measured values. The organic matter [dissolved organic carbon (DOC) or UV absorbance at 254 nm] and bromide exerted the most important influence on the formation of HANs. While for THMs, besides the organic matter and bromide, reaction time was also a key factor. Comparing the models for total THMs (T-THMs) in this study with others revealed that the regression models from the low SUVA waters may have low DOC coefficients, but high bromide coefficients as compared with those from the high SUVA waters.