Bio-catalyzed oxidation self-charging zinc-polymer batteries.

Oxidation self-charging batteries have emerged with the demand for powering electronic devices around the clock. The low efficiency of self-charging has been the key challenge at present. Here, a more efficient autoxidation self-charging mechanism is realized by introducing hemoglobin (Hb) as a positive electrode additive in the polyaniline (PANI)-zinc battery system. The heme acts as a catalyst that reduces the energy barrier of the autoxidation reaction by regulating the charge and spin state of O2. To realize self-charging, the adsorbed O2 molecules capture electrons of the reduced (discharged state) PANI, leading to the desorption of zinc ions and the oxidation of PANI to complete self-charging. The battery can discharge for 12 min (0.5 C) after 50 self-charging/discharge cycles, while there is nearly no discharge capacity in the absence of Hb. This biology-inspired electronic regulation strategy may inspire new ideas to boost the performance of self-charging batteries.

Resistivity detection of perfluoroalkyl substances with fluorous polyaniline in an electrical lateral flow sensor.

Perfluoroalkyl substances (PFAS), known as "forever chemicals," are a growing concern in the sphere of human and environmental health. In response, rapid, reproducible, and inexpensive methods for PFAS detection in the environment and home water supplies are needed. We have developed a simple and inexpensive perfluoroalkyl acid detection method based on an electrically read lateral flow assay (e-LFA). Our method employs a fluorous surfactant formulation with undoped polyaniline (F-PANI) fabricated to create test lines for the lateral flow assay. In perfluoroalkyl acid sensing studies, an increase in conductivity of the F-PANI film is caused by acidification and doping of PANI. A conductivity enhancement by 104-fold can be produced by this method, and we demonstrate a limit of detection for perfluorooctanoic acid (PFOA) of 400 ppt and perfluorobutanoic acid of 200 ppt. This method for PFOA detection can be expanded for wide-scale environmental and at-home water testing.

Proton is Essential or Not: A Fresh Look on Pseudocapacitive Energy Storage of PANI Composites.

Protonation has been considered essential for the pseudocapacitive energy storage of polyaniline (PANI) for years, as proton doping in PANI chains not only activates electron transport pathways, but also promotes the proceeding of redox reactions. Rarely has the ability for PANI of storing energy without protonation been investigated, and it remains uncertain whether PANI has pseudocapacitive charge storage properties in an alkaline electrolyte. Here, this work first demonstrates the pseudocapacitive energy storage for PANI without protonation using a PANI/graphene composite as a model material in an alkaline electrolyte. Using in situ Raman spectroscopy coupled with electrochemical quartz crystal microbalance (EQCM) measurements, this work determines the formation of -N= group over potential on a PANI chain and demonstrates the direct contribution of OH- in the nonprotonation type of oxidation reactions. This work finds that the PANI/graphene composite in an alkaline electrolyte has excellent cycling stability with a wider operation voltage of 1 V as well as a slightly higher specific capacitance than that in an acidic electrolyte. The findings provide a new perspective on pseudocapacitive energy storage of PANI-based composites, which will influence the selection of electrolytes for PANI materials and expand their application in energy storage fields.

Manipulation of Conducting Polymer Hydrogels with Different Shapes and Related Multifunctionality.

Maneuver of conducting polymers (CPs) into lightweight hydrogels can improve their functional performances in energy devices, chemical sensing, pollutant removal, drug delivery, etc. Current approaches for the manipulation of CP hydrogels are limited, and they are mostly accompanied by harsh conditions, tedious processing, compositing with other constituents, or using unusual chemicals. Herein, a two-step route is introduced for the controllable fabrication of CP hydrogels in ambient conditions, where gelation of the shape-anisotropic nano-oxidants followed by in-situ oxidative polymerization leads to the formation of polyaniline (PANI) and polypyrrole hydrogels. The method is readily coupled with different approaches for materials processing of PANI hydrogels into varied shapes, including spherical beads, continuous wires, patterned films, and free-standing objects. In comparison with their bulky counterparts, lightweight PANI items exhibit improved properties when those with specific shapes are used as electrodes for supercapacitors, gas sensors, or dye adsorbents. The current study therefore provides a general and controllable approach for the implementation of CP into hydrogels of varied external shapes, which can pave the way for the integration of lightweight CP structures with emerging functional devices.

Large-Area Fabrication of Porous Graphene Networks on Carbon Fabric via Millisecond Photothermal Processing of Polyaniline for Supercapacitors.

Supercapacitors demonstrate promising potential for flexible, multi-functional energy storage devices; however, their widespread adoption is confronted by fabrication challenges. To access a combination of desirable device qualities such as flexibility, lightweight, structural stability, and enhanced electrochemical performance, carbon fiber (CF) can be utilized as a current collector, alongside graphene as an electrochemically active material. Yet achieving a cost-effective, large-scale graphene production, particularly on CF, remains challenging. Here, a rapid (<1 min) photothermal approach is developed for the large-scale production of graphene directly onto CF, utilizing polyaniline (PANI) as a polymer precursor. The in situ electropolymerization of PANI on CF facilitates its rapid synthesis on large areas, followed by conversion into graphene networks, enabling the binder-free fabrication of supercapacitor devices. These devices exhibit an areal capacitance of 180 mF cm-2 (at 2 mA cm-2 in 1 m H2SO4), an order of magnitude higher than other fabric-based devices. Moreover, the devised photothermal strategy allows for one-step preparation of supercapacitor devices on areas exceeding 100 cm-2, yielding an absolute areal capacitance of 4.5 F. The proportional increase in capacitance with device area facilitates scaling and indicates the commercial viability of this approach for low-cost, energy-efficient, and high-throughput production of lightweight, high-performance graphene-based multi-functional supercapacitor devices.

Super-Elastic and Temperature-Tolerant Hydrogel Electrodes for Supercapacitors via MXene Enhanced Ice-Templating Synthesis.

Developing flexible energy storage devices with good deformation resistance under extreme operating conditions is highly desirable yet remains very challenging. Super-elastic MXene-enhanced polyvinyl alcohol/polyaniline (AMPH) hydrogel electrodes are designed and synthesized through vertical gradient ice templating-induced polymerization. This approach allows for the unidirectional growth of polyaniline (PANI) and 2D MXene layers along the elongated arrayed ice crystals in a controlled manner. The resulting 3D unidirectional AMPH hydrogel exhibits inherent stretchability and electronic conductivity, with the ability to completely recover its shape even under extreme conditions, such as 500% tensile strain, 50% compressive strain. The presence of MXene in the hydrogel electrode enhances its resilience to mechanical compression and stretching, resulting in less variation in resistance. AMPH has a specific capacitance of 130.68 and 88.02 mF cm-2 at a current density of 0.2 and 2 mA cm-2, respectively, and retains 90% and 70% of its original capacitance at elongation of 100% and 200%, respectively. AMPH-based supercapacitors demonstrate exceptional performance in high salinity environments and wide temperature ranges (-30-80 °C). The high electrochemical activity, temperature tolerance, and mechanical robustness of AMPH-based supercapacitor endow it promising as the power supply for flexible and wearable electronic devices.

Hollow Superstructure In Situ Assembled by Single-Layer Janus Nanospheres toward Electromagnetic Shielding Flame-Retardant Polyurea Composites.

A dodecahedral superstructure consisting of a single layer of Janus spheres containing ZIF-67 nanodots is prepared by in situ polymerization, with ZIF-67 and bio-based phytic acid (PA) as templates and dopants. It is used to improve the flame retardant, electromagnetic (EMI) shielding, and thermal conductivity properties of polyurea (PUA). By adding 5 wt% polyaniline@cobalt phytate-2.0 (PANI@Co-PA-2.0), the peak of heat release rate and the peak of smoke production rate are reduced by 54.9 and 59.9%, respectively. The peak of CO and CO2 production also decreased by 46.2 and 53.1%, respectively. A decrease in the absorption intensity of aliphatic and aromatic volatiles is also observed. The fire safety of PUA is greatly improved. In addition, PUA/PANI@Co-PA-2.0 exhibits an EMI shielding capability of 22.4 dB with the help of reduced graphene oxide, which confirms the possibility of PUA material application in the field of electromagnetic shielding. The 5 wt% filler increases the tensile strength of the PUA matrix to 6.3 MPa, and the composite material obtains good thermal conductivity. This work provides a viable method for the preparation of a flame-retardant, conductive, and electromagnetic refractory PUA substrate.

Analogous Confinement Effect Enables High Stability and High Capacity Ammonium Storage in Polyaniline@Poly(o-fluoroaniline)@Carbon Layer.

Rechargeable aqueous ammonium ion (NH4 +) batteries have attracted much attention due to the unique properties of NH4 +. Polyaniline (PA) with outstanding conductivity is a potential cathode material, but it can be oxidized to pernigraniline (PG) rapidly, resulting in its poor stability. In this study, polyaniline@poly(o-fluoroaniline)@carbon layer (PA@POFA@C) is prepared for excellent and durable NH4 + storage. PA@POFA@C exhibits a high capacity of 208 mAh g-1 at 0.2 A g-1 and maintains 126 mAh g-1 at 10 A g-1. More importantly, an excellent capacity retention rate of 88.24% is achieved after 2000 cycles with ≈100% coulombic efficiency. Spectroscopy studies suggest analogous confinement effect can effectively limit the escape of hydrogen in imine group, and form the hydrogen-restricted region between the PA and POFA layer which can provide H+ for the complete reduction of PG. Meanwhile, the hydrophobic effect of POFA effectively restrains the hydrolysis of PG. Interestingly, the introduction of C layer improves the hydrophilicity of electrode and shortens the activation process, serving as the outermost protective layer of the electrode. Finally, PA@POFA@C achieves desirable electrochemical performances with analogous confinement effect. This research provides ideas for the preparation of advanced polymer electrodes for aqueous NH4 + batteries.

Amplifying reactivity of bio-inspired [FeFe]-hydrogenase mimics by organic nanotubes.

A bio-inspired FeFe hydrogenase model which catalyses hydrogen evolution reaction (HER) in acidic solutions is immobilized in polyaniline (PANI)-based nanotubes. A combination of analytical techniques reveals that this construct maintains both the molecular signatures of the bio-inspired complex and the material properties of PANI. The amine and imine-rich environment of the PANI chain amplifies the inherent HER activity of the bio-inspired complex, allowing electrocatalytic HER at neutral pH, with lower overpotentials and higher current densities compared to the bio-inspired complex alone. This construct retains the oxygen stability of the bio-inspired complex and remains stable through several hours of aerobic electrolysis, producing only 6.5% H2O2 from the competing oxygen reduction reaction (ORR).

Recent Progress in Polyaniline and its Composites for Supercapacitors.

Polyaniline (PANI) has piqued the interest of nanotechnology researchers due to its potential as an electrode material for supercapacitors. Despite its ease of synthesis and ability to be doped with a wide range of materials, PANI's poor mechanical properties have limited its use in practical applications. To address this issue, researchers investigated using PANI composites with materials with highly specific surface areas, active sites, porous architectures, and high conductivity. The resulting composite materials have improved energy storage performance, making them promising electrode materials for supercapacitors. Here, we provide an overview of recent developments in PANI-based supercapacitors, focusing on using electrochemically active carbon and redox-active materials as composites. We discuss challenges and opportunities of synthesizing PANI-based composites for supercapacitor applications. Furthermore, we provide theoretical insights into the electrical properties of PANI composites and their potential as active electrode materials. The need for this review stems from the growing interest in PANI-based composites to improve supercapacitor performance. By examining recent progress in this field, we provide a comprehensive overview of the current state-of-the-art and potential of PANI-based composites for supercapacitor applications. This review adds value by highlighting challenges and opportunities associated with synthesizing and utilizing PANI-based composites, thereby guiding future research directions.

Modulation of polyaniline memristive device switching voltage by nucleotide-free analogue of vitamin B12.

Memristive devices offer essential properties to become a part of the next-generation computing systems based on neuromorphic principles. Organic memristive devices exhibit a unique set of properties which makes them an indispensable choice for specific applications, such as interfacing with biological systems. While the switching rate of organic devices can be easily adjusted over a wide range through various methods, controlling the switching potential is often more challenging, as this parameter is intricately tied to the materials used. Given the limited options in the selection conductive polymers and the complexity of polymer chemical engineering, the most straightforward and accessible approach to modulate switching potentials is by introducing specific molecules into the electrolyte solution. In our study, we show polyaniline (PANI)-based device switching potential control by adding nucleotide-free analogue of vitamin B12, aquacyanocobinamide, to the electrolyte solution. The employed concentrations of this molecule, ranging from 0.2 to 2 mM, enabled organic memristive devices to achieve switching potential decrease for up to 100 mV, thus providing a way to control device properties. This effect is attributed to strong aromatic interactions between PANI phenyl groups and corrin macrocycle of the aquacyanocobinamide molecule, which was supported by ultraviolet-visible spectra analysis.

Unique Core-Shell Structured Polyaniline Nanofibers Toward Ultrahigh-Rate Flexible All-Solid-State Supercapacitor.

Promoting charge storage and fast charging capability simultaneously is a long-standing challenge for supercapacitors. A facile flowing seed polymerization is adopted to prepare polyaniline (PANI) nanofibers, in which phytic acid (PA) doped oligomers are first produced as the seeds for promoting the highly oriented growth of PANI nanofibers accompanying with the copolymerization of m-aminobenzene sulfonic acid (ASA) and aniline occurred on the surface of PANI nanofibers, as a result, unique core-shell structured PANI nanofibers are continuously fabricated. Benefitting from compact nanofiber structure, excellent dispersion, and self-doping effect, as-prepared PANI nanofibers exhibit a specific capacitance of 671.2 F g-1 at 2 A g-1 and ultrahigh rate capability of 93.1% from 2 to 100 A g-1. Then assembled all-solid-state supercapacitor can deliver the highest energy density of 28.3 Wh kg-1 at a power density of 320.2 W kg-1 with remarkable rate capability (81.2% from 1 to 20 A g-1), cycle stability (77.5% after 5000 cycles) as well as light weight and flexibility. It is highly desirable that the present green and scalable approach can be further applied to fabricate other unique core-shell structured PANI nanofibers with appealing potentials in energy storage devices.

Eco-friendly engineering of micro composite-based hydroxyapatite bio crystal and polyaniline for high removal of OG dye from wastewater: Adsorption mechanism and RSM@BBD optimization.

The presence of harmful substances such as dyes in water systems poses a direct threat to the quality of people's lives and other organisms living in the ecosystem. Orange G (OG) is considered a hazardous dye. The existing paper attempts to evaluate a low-cost adsorbent for the effective removal of OG dye. The developed adsorbent Polyaniline@Hydroxyapatite extracted from Cilus Gilberti fish Scale (PANI@FHAP) was elaborated through the application of the in situ chemical polymerization method to incorporate PANI on the surface of naturally extracted hydroxyapatite FHAP. The good synthesis of PANI@FHAP was evaluated through multiple techniques including X-ray diffraction (XRD), Scanning electron microscopy coupled with energy dispersive X-ray spectrometry (SEM/EDS), Fourier Transforms Infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) coupled with thermal differential analysis (DTA) analysis. The results reveal a highly ordered disposition of PANI chains on FHAP, resulting in a well-coated FHAP in the PANI matrix. Furthermore, the presence of functional groups on the surface of PANI such as amine (-NH2) and imine (=NH) groups would facilitate the removal of OG dye from contaminated water. The adsorption of OG onto PANI@FHAP was conducted in batch mode and optimized through response surface methodology coupled with box-Behnken design (RSM/BBD) to investigate the effect of time, adsorbent dose, and initial concentration. The outcomes proved that OG adsorption follows a quadratic model (R2 = 0.989). The kinetic study revealed that the adsorption of OG fits the pseudo-second-order model. On the other hand, the isotherm study declared that the Freundlich model is best suited to the description of OG adsorption. For thermodynamic study, the adsorption of OG is spontaneous in nature and exothermic. Furthermore, the regeneration-reusability study indicates that PANI@FHAP could be regenerated and reused up to five successive cycles. Based on the FTIR spectrum of PANI@FHAP after OG adsorption, the mechanism governing OG adsorption is predominantly driven by π-π interaction, electrostatic interaction, and hydrogen bonding interactions. The obtained results suppose that PANI@FHAP adsorbent can be a competitive material in large-scale applications.

Response surface methodology use in construction of polianiline-coated carbon paste electrode-based biosensor: Modification and characterization.

In this study, the effect of amperometric glucose biosensor construction and using conditions on the current response was investigated in detail applying experimental design. Polyaniline (PANI) was synthesized on the carbon paste electrode (CPE) surface using the cyclic voltammetry technique in sodium oxalate (NaOx ) electrolyte medium, and an amperometric biosensor was constructed by immobilizing glucose oxidase (GOD). Biosensor preparation (aniline, GOD and NaOx concentrations, and scan rate) and operating conditions (pH and applied potential) were optimized by Box-Behnken and optimal designs, respectively, via State Ease Design Expert 7.0.1.1 software. ANOVA analyses showed that among the biosensor preparation parameters, the NaOx concentration has the highest effect on the current measured in the presence of glucose, whereas in the optimization of pH and potential parameters applied in current measurement studies, it has been revealed that pH has a very high effect on the measured current. Several compounds, such as MWCNT, two different ionic liquids and two different organic molecules were added to carbon paste, and, among them, 2-cyanoethylpyrrole (CPy) enhanced the efficacy highly, most probably due to its polymerization in the paste and increasing the electron transfer rate of the CPE. Sucrose- and lactose-sensitive biosensors were also constructed by co-immobilizing GOD with invertase (INV) or ß-galactosidase, respectively, onto modified CPE, and sensitivities to their substrates were shown by cyclic voltammetry and impedance analysis. CPy modification caused an increase in the current values, and also Imax /KM values increased approximately 11.8, 7.83, and 2.56 times for glucose-, sucrose-, and lactose-sensitive CPEs, respectively.

Development of an amperometric biosensor that can determine the amount of glucose in the blood using the glucose oxidase enzyme: Preparation of polyaniline-polypyrrole-poly(sodium-4-styrenesulfonate) film.

In this study, a new amperometric biosensor was developed for glucose determination. For this purpose, polyaniline-polypyrrole-poly(sodium-4-styrenesulfonate) film was prepared by electropolymerization of aniline and pyrrole with poly(sodium-4-styrenesulfonate) on a platinum plate. The best working conditions of the polyaniline-polypyrrole-poly(sodium-4-styrenesulfonate) film were determined. The glucose oxidase enzyme was immobilized by the entrapment method in polyaniline-polypyrrole-poly(sodium-4-styrenesulfonate) film. Glucose determination was made based on the oxidation of hydrogen peroxide, which is formed as a result of the enzymatic reaction on the surface of the prepared biosensor at +0.40 V. The working range for the glucose determination of the biosensor was determined. The effects of pH and temperature on the response of the glucose biosensor were investigated. The reusability and shelf life of the biosensor were determined. The effects of interference in biological environments on the response of the biosensor were investigated. Glucose determination was made in the biological fluid (blood) with the prepared biosensor. This study has a feature that sheds light on biosensor studies to be developed for the detection of substances in the human body, such as glucose, uric acid, and urea. This article will set an example for future scientific research on the development of a sensor for other biological fluids in the human body, such as the sensor developed for blood samples. In addition, this developed sensor provides an innovation that improves the quality of life of patients by allowing them to constantly monitor their glucose levels and intervene when necessary.

Ultra-high sensitivity pH sensor based on vertical organic electrochemical transistors with extended gate.

An ultra-high sensitivity pH sensor based on vertical organic electrochemical transistors (vOECT) with extended gate was proposed. The vOECT, which exhibited high transconductance (gm), was for the first time used in the preparation of a pH sensor. The extended gate was modified by electrochemical deposition of polyaniline (PANI) using the cyclic voltammetry (CV) technique. Open circuit potential (OCP) measurements were used to optimize the scan rate, showing a super-Nernstian sensitivity at all scan rates. The pH sensor based on vOECT with extended gate was investigated at different pH levels, and it exhibited an ultra-high sensitivity of 3363.6 µA/pH in the pH range 5-9, which was about 36 times greater than the maximum current sensitivity (91 µA/pH) of other transistor-based pH sensors, to the best of our knowledge. This pH sensor performed excellently in terms of reversibility, long-term stability, and selectivity. To confirm the reliability of the pH sensor, we conducted measurements on real samples using this pH sensor and compared the results with those obtained from a standard pH meter. The ultra-high sensitivity pH sensor based on vOECT with extended gate offers a sensitive and promising alternative in environmental monitoring, food safety, chemistry, clinical diagnostics, and bio-sensing applications.

Disposable electrochemical sensors based on reduced graphene oxide/polyaniline/poly(alizarin red S)-modified integrated carbon electrodes for the detection of ciprofloxacin in milk.

An electrochemical sensor based on an electroactive nanocomposite was designed for the first time consisting of electrochemically reduced graphene oxide (ERGO), polyaniline (PANI), and poly(alizarin red S) (PARS) for ciprofloxacin (CIPF) detection. The ERGO/PANI/PARS-modified screen-printed carbon electrode (SPCE) was constructed through a three-step electrochemical protocol and characterized using FTIR, UV-visible spectroscopy, FESEM, CV, LSV, and EIS. The new electrochemical CIPF sensor demonstrated a low detection limit of 0.0021 µM, a broad linear range of 0.01 to 69.8 µM, a high sensitivity of 5.09 µA/µM/cm2, and reasonable selectivity and reproducibility. Moreover, the ERGO/PANI/PARS/SPCE was successfully utilized to determine CIPF in milk with good recoveries and relative standard deviation (< 5%), which were close to those with HPLC analysis.

Preparation of PANI-SA/CF anode to enhance the remediation and power generation capabilities of plant microbial fuel cells for chromium contaminated soil.

Plant microbial fuel cells (PMFCs) has important value for soil remediation and power generation. To improve the performance of PMFCs, a PMFC experimental system was established based on potted scindapsus aureus. Polyaniline (PANI) and sodium alginate (SA) were used as modifiers to prepare PANI-SA modified carbon felt anode. The soil remediation ability and electricity generation ability of PMFCs with four different anodes were compared and analyzed. The experimental results show that the steady-state voltage, the removal rate of hexavalent chromium, and the total chromium removal rate of PMFC using PANI-SA modified anode were 5.25 mV, 98%, and 90%, respectively, which are 253%, 10.4%, and 10% higher than those of PMFCs using unmodified carbon felt anode. PMFC is effective and feasible for removing soil chromium pollution and achieving efficient soil remediation, while modifying anodes with PANI-SA can further improve the soil remediation and electricity generation capabilities of PMFC.

A Flexible Ammonia Gas Sensor Based on a Grafted Polyaniline Grown on a Polyethylene Terephthalate Film.

A novel NH3 gas sensor is introduced, employing polyaniline (PANI) with a unique structure called a graft film. The preparation method was simple: polydopamine (PD) was coated on a flexible polyethylene terephthalate (PET) film and PANI graft chains were grown on its surface. This distinctive three-layer sensor showed a response value of 12 for 50 ppm NH3 in a dry atmosphere at 50 °C. This value surpasses those of previously reported sensors using structurally controlled PANI films. Additionally, it is on par with sensors that combine PANI with metal oxide semiconductors or carbon materials, the high sensitivity of which have been reported. To confirm our film's potential as a flexible sensor, the effect of bending on the its characteristics was investigated. This revealed that although bending decreased the response value, it had no effect on the response time or recovery. This indicated that the sensor film itself was not broken by bending and had sufficient mechanical strength.

Molecular Engineering of Hierarchical Conducting Polymer Composites for Highly Stable Supercapacitors.

Long cycle life and high energy/power density are imperative to energy storage systems. Polyaniline (PANI) has shown great potential as an electrode material but is limited by poor cycling and rate performance. We present a molecular design approach of binding short-chain aniline trimers (ATs) and carbon nanotubes (CNTs) through the formation of amide covalent linkages enabled by a simple laser scribing technique. The covalently coupled AT/CNT (cc-AT/CNT) composite retains 80% of its original capacitance after 20 000 charge/discharge cycles, which readily outperforms long-chain PANI/CNT composites without covalent connections. The compact AT/CNT heterointerfaces produce fast charge/discharge kinetics and excellent rate capability. The flexible symmetric quasi-solid-state devices can be stably cycled beyond 50 000 cycles, at least 5 times longer than most PANI/CNT-based symmetric supercapacitors reported to date. This molecular design of durable conducting polymer-based electrode materials enabled by laser irradiation presents a feasible approach toward robust advanced energy storage devices.