Breaking the Bottleneck of Activity and Stability of RuO2-Based Electrocatalysts for Acidic Oxygen Evolution.

Electrochemical acidic oxygen evolution reaction (OER) is an important part for water electrolysis utilizing a proton exchange membrane (PEM) apparatus for industrial H2 production. RuO2 has garnered considerable attention as a potential acidic OER electrocatalyst. However, the overoxidation of Ru active sites under high potential conditions is usually harmful for activity and stability, thereby posing a challenge for large-scale commercialization, which needs effective strategies to circumvent the leaching of Ru and further activate Ru sites. Herein, a Mini-Review is presented to summarize the recent developments regarding the activation and stabilization of the Ru active sites and lattice oxygen through the modulation of the d-band center, coordination environment, bridged heteroatoms, and vacancy engineering, as well as structural protection strategies and reaction pathway optimization to promote the acidic OER activity and stability of RuO2-based electrocatalysts. This Mini-Review offers a profound understanding of the design of RuO2-based electrocatalysts with greatly enhanced acidic OER performances.

Dense-Packed RuO2 Nanorods with In Situ Generated Metal Vacancies Loaded on SnO2 Nanocubes for Proton Exchange Membrane Water Electrolyzer with Ultra-Low Noble Metal Loading.

Proton exchange membrane water electrolyzer (PEMWE) is a green hydrogen production technology that can be coupled with intermittent power sources such as wind and photoelectric power. To achieve cost-effective operations, low noble metal loading on the anode catalyst layer is desired. In this study, a catalyst with RuO2 nanorods coated outside SnO2 nanocubes is designed, which forms continuous networks and provides high conductivity. This allows for the reduction of Ru contents in catalysts. Furthermore, the structure evolutions on the RuO2 surface are carefully investigated. The etched RuO2 surfaces are seen as the consequence of Co leaching, and theoretical calculations demonstrate that it is more effective in driving oxygen evolution. For electrochemical tests, the catalysts with 23 wt% Ru exhibit an overpotential of 178 mV at 10 mA cm-2 , which is much higher than most state-of-art oxygen evolution catalysts. In a practical PEMWE, the noble metal Ru loading on the anode side is only 0.3 mg cm-2 . The cell achieves 1.61 V at 1 A cm-2 and proper stability at 500 mA cm-2 , demonstrating the effectiveness of the designed catalyst.

Self-Supporting Mn-RuO2 Nanoarrays for Stable Oxygen Evolution Reaction in Acid.

Currently, the process of an acidic oxygen evolution reaction (OER) necessitates the use of Iridium dioxygen (IrO2), which is both expensive and incredibly scarce on Earth. Ruthenium dioxygen (RuO2) offers high activity for acidic OERs and presents a potential substitution for IrO2. Nevertheless, its practical application is hindered by its relatively poor stability. In this study, we have developed Mn-doped RuO2 (Mn-RuO2) nanoarrays that are anchored on a titanium (Ti) mesh utilizing a two-step methodology involving the preparation of MnO2 nanoarrays followed by a subsequent Ru exchange and annealing process. By precisely optimizing the annealing temperature, we have managed to attain a remarkably low overpotential of 217 mV at 10 mA cm-2 in a 0.5 M H2SO4 solution. The enhanced catalytic activity of our Mn-RuO2 nanoarrays can be attributed to the electronic modification brought about by the high exposure of active sites, Mn dopant, efficient mass transfer, as well as the efficient transfer of electrons between the Ti mesh and the catalyst arrays. Furthermore, these self-supported Mn-RuO2 nanoarrays demonstrated excellent long-term stability throughout a chronoamperometry test lasting for 100 h, with no discernible changes observed in the Ru chemical states.

Exfoliation and Reassembly Routes to a Ge/RuO2 Nanocomposite as an Anode for Advanced Lithium-Ion Batteries.

Ge/RuO2 nanocomposites were successfully fabricated as anode materials for lithium-ion batteries using RuO2 nanosheets and Ge/GeO2 nanoparticles (NPs). X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) analyses showed that elemental Ge nanoparticles were distributed onto the rutile-type RuO2. Transmission electron microscopy images showed well-dispersed Ge nanoparticles embedded in rutile-type RuO2. The Ge/RuO2 nanocomposite maintained higher discharge capacities (471 mA h g-1) after the 90th cycle at 0.1 A g-1 than that (211 mA h g-1) of Ge/GeO2 nanoparticles. The Ge/RuO2 nanocomposite exhibited a higher capacity retention than Ge/GeO2 NPs. These results suggest that the well-dispersed Ge nanoparticles within RuO2 matrices enhance the cycle stability and capacity retention of the anode material.

Water-Assisted Chemical Route Towards the Oxygen Evolution Reaction at the Hydrated (110) Ruthenium Oxide Surface: Heterogeneous Catalysis via DFT-MD and Metadynamics Simulations.

Notwithstanding that RuO2 is a promising catalyst for the oxygen evolution reaction (OER), a plethora of fundamental details on its catalytic properties are still elusive, severely limiting its large-scale deployment. It is also established experimentally that corrosion and wettability of metal oxides can, in fact, enhance the catalytic activity for OER owing to the formation of a hydrated surface layer. However, the mechanistic interplay between surface wettability, interfacial water dynamics and OER across RuO2 , and what degree these processes are correlated are still debated. Herein, spin-polarized Density Functional Theory Molecular Dynamics (DFT-MD) simulations, coupled with advanced enhanced sampling methods in the well-tempered metadynamics framework, are applied to gain a global understanding of RuO2 aqueous interface (explicit water solvent) in catalyzing the OER, and hence possibly help in the design of novel catalysts in the context of photochemical water oxidation. The present study quantitatively assesses the free-energy barriers behind the OER at the (110)-RuO2 catalyst surface revealing plausible pathways composing the reaction network of the O2 evolution. In particular, OER is investigated at room temperature when such a surface is exposed to both gas-phase and liquid-phase water. Albeit a unique efficient pathway has been identified in the gas-phase OER, a surprisingly lowest-free-energy-requiring reaction route is possible when (110)-RuO2 is in contact with explicit liquid water. By estimating the free-energy surfaces associated to these processes, we reveal a noticeable water-assisted OER mechanism which involves a crucial proton-transfer-step assisted by the local water environment. These findings pave the way toward the systematic usage of DFT-MD coupled with metadynamics techniques for the fine assessment of the activity of catalysts, considering finite-temperature and explicit-solvent effects.

Monitoring Contractile Cardiomyocytes via Impedance Using Multipurpose Thin Film Ruthenium Oxide Electrodes.

A ruthenium oxide (RuOx) electrode was used to monitor contractile events of human pluripotent stem cells-derived cardiomyocytes (hPSC-CMs) through electrical impedance spectroscopy (EIS). Using RuOx electrodes presents an advantage over standard thin film Pt electrodes because the RuOx electrodes can also be used as electrochemical sensor for pH, O2, and nitric oxide, providing multisensory functionality with the same electrode. First, the EIS signal was validated in an optically transparent well-plate setup using Pt wire electrodes. This way, visual data could be recorded simultaneously. Frequency analyses of both EIS and the visual data revealed almost identical frequency components. This suggests both the EIS and visual data captured the similar events of the beating of (an area of) hPSC-CMs. Similar EIS measurement was then performed using the RuOx electrode, which yielded comparable signal and periodicity. This mode of operation adds to the versatility of the RuOx electrode's use in in vitro studies.

Fabrication, Potentiometric Characterization, and Application of Screen-Printed RuO2 pH Electrodes for Water Quality Testing.

Screen-printed sensing electrodes attract much attention for water pollution monitoring due to their small size, physical and chemical durability, and low cost. This paper presents the fabrication and broad potentiometric characterization of RuO2 pH sensing electrodes deposited by screen printing on alumina substrates and sintered in the 800-900 °C temperature range. All the fabricated electrodes showed close to Nernstian sensitivity, good linearity, fast response, small drift, low hysteresis, and low cross-sensitivity toward various interfering cations and anions. Furthermore, decreasing the sintering temperature led to better adhesion of the RuO2 layer and a negligible response to interfering ions. The measurements in real-life samples from different water sources showed that the fabricated electrodes are on par with conventional glass electrodes with a maximum deviation of 0.11 pH units, thus indicating their potential for application in water quality monitoring.

Thermal Activation of CH4 and H2 as Mediated by the Ruthenium Oxide Cluster Ions [RuOx ]+ (x=1-3): On the Influence of Oxidation States.

Thermal gas-phase reactions of the ruthenium-oxide clusters [RuOx ]+ (x=1-3) with methane and dihydrogen have been explored by using FT-ICR mass spectrometry complemented by high-level quantum chemical calculations. For methane activation, as compared to the previously studied [RuO]+ /CH4 couple, the higher oxidized Ru systems give rise to completely different product distributions. [RuO2 ]+ brings about the generations of [Ru,O,C,H2 ]+ /H2 O, [Ru,O,C]+ /H2 /H2 O, and [Ru,O,H2 ]+ /CH2 O, whereas [RuO3 ]+ exhibits a higher selectivity and efficiency in producing formaldehyde and syngas (CO+H2 ). Regarding the reactions with H2 , as compared to CH4 , both [RuO]+ and [RuO2 ]+ react similarly inefficiently with oxygen-atom transfer being the main reaction channel; in contrast, [RuO3 ]+ is inert toward dihydrogen. Theoretical analysis reveals that the reduction of the metal center drives the overall oxidation of methane, whereas the back-bonding orbital interactions between the cluster ions and dihydrogen control the H-H bond activation. Furthermore, the reactivity patterns of [RuOx ]+ (x=1-3) with CH4 and H2 have been compared with the previously reported results of Group 8 analogues [OsOx ]+ /CH4 /H2 (x=1-3) and the [FeO]+ /H2 system. The electronic origins for their distinctly different reaction behaviors have been addressed.

A New Calibration Circuit Design to Reduce Drift Effect of RuO2 Urea Biosensors.

The goal of this study was to reduce the drift effect of RuO2 urea biosensors. A new calibration circuit (NCC) based on the voltage regulation technique with the advantage of having a simple structure was presented. To keep its simplicity, the proposed NCC was composed of a non-inverting amplifier and a voltage calibrating circuit. A ruthenium oxide (RuO2) urea biosensor was fabricated to test the calibrating characteristics of the drift rate of the proposed NCC. The experiment performed in this study was divided into two main stages. For the first stage, a sound RuO2 urea biosensor testing environment was set-up. The RuO2 urea sensing film was immersed in the urea solution for 12 h and the response voltage was measured using the voltage-time (V-T) measurement system and the proposed NCC. The results of the first stage showed that the RuO2 urea biosensor has an average sensitivity of 1.860 mV/(mg/dL) and has a linearity of 0.999 which means that the RuO2 urea biosensor had been well fabricated. The second stage of the experiment verified the proposed NCC's functions, and the results indicated that the proposed NCC reduced the drift rate of RuO2 urea biosensor to 0.02 mV/hr (98.77% reduction).

Nano-RuO2 -Decorated Holey Graphene Composite Fibers for Micro-Supercapacitors with Ultrahigh Energy Density.

Compactness and versatility of fiber-based micro-supercapacitors (FMSCs) make them promising for emerging wearable electronic devices as energy storage solutions. But, increasing the energy storage capacity of microscale fiber electrodes, while retaining their high power density, remains a significant challenge. Here, this issue is addressed by incorporating ultrahigh mass loading of ruthenium oxide (RuO2 ) nanoparticles (up to 42.5 wt%) uniformly on nanocarbon-based microfibers composed largely of holey reduced graphene oxide (HrGO) with a lower amount of single-walled carbon nanotubes as nanospacers. This facile approach involes (1) space-confined hydrothermal assembly of highly porous but 3D interconnected carbon structure, (2) impregnating wet carbon structures with aqueous Ru3+ ions, and (3) anchoring RuO2 nanoparticles on HrGO surfaces. Solid-state FMSCs assembled using those fibers demonstrate a specific volumetric capacitance of 199 F cm-3 at 2 mV s-1 . Fabricated FMSCs also deliver an ultrahigh energy density of 27.3 mWh cm-3 , the highest among those reported for FMSCs to date. Furthermore, integrating 20 pieces of FMSCs with two commercial flexible solar cells as a self-powering energy system, a light-emitting diode panel can be lit up stably. The current work highlights the excellent potential of nano-RuO2 -decorated HrGO composite fibers for constructing micro-supercapacitors with high energy density for wearable electronic devices.

Ruthenium Oxide Nanorods as Potentiometric pH Sensor for Organs-On-Chip Purposes.

A ruthenium oxide (RuOx) sensor for potentiometric pH sensing is currently being developed for organs-on-chip purposes. The sensor was fabricated from a Ru(OH)3 precursor, resulting in RuOx nanorods after heating. An open-circuit potential of the RuOx electrode showed a near-Nernstian response of -58.05 mV/pH, with good selectivity against potentially interfering ions (lithium, sulfate, chloride, and calcium ions). The preconditioned electrode (stored in liquid) had a long-term drift of -0.8 mV/h, and its response rate was less than 2 s. Sensitivity to oxygen was observed at an order of magnitude lower than other reported metal-oxide pH sensors. Together with miniaturizability, the RuOx pH sensor proves to be a suitable pH sensor for organs-on-chip studies.

On the Origin of the Distinctly Different Reactivity of Ruthenium in [MO]+ /CH4 Systems (M=Fe, Ru, Os).

The thermal gas-phase reactions of [RuO]+ with methane have been explored by FT-ICR mass spectrometry and high-level quantum-chemical calculations. In contrast to the previously studied [FeO]+ /CH4 and [OsO]+ /CH4 couples, which undergo oxygen/hydrogen atom transfers and dehydrogenation, respectively, the [RuO]+ /CH4 system produces selectively [Ru(CH)2 ]+ and H2 O, albeit with much lower efficiency. Various mechanistic scenarios were uncovered, and the associated electronic origins were revealed by high-level quantum-chemical calculations. The reactivity differences observed for the [MO]+ /CH4 couples (M=Fe, Ru, Os) are due to the subtle interplay of the spin-orbit coupling efficiency, orbital overlap, and relativistic effects.

RuO₂ pH Sensor with Super-Glue-Inspired Reference Electrode.

A pH-sensitive RuO₂ electrode coated in a commercial cyanoacrylate adhesive typically exhibits very low pH sensitivity, and could be paired with a RuO₂ working electrode as a differential type pH sensor. However, such sensors display poor performance in real sample matrices. A pH sensor employing a RuO₂ pH-sensitive working electrode and a SiO₂-PVB junction-modified RuO₂ reference electrode is developed as an alternative high-performance solution. This sensor exhibits a performance similar to that of a commercial glass pH sensor in some common sample matrices, particularly, an excellent pH sensitivity of 55.7 mV/pH, a hysteresis as low as 2.7 mV, and a drift below 2.2 mV/h. The developed sensor structure opens the way towards the development of a simple, cost effective, and robust pH sensor for pH analysis in various sample matrices.

One-Dimensional RuO2/Mn2O3 Hollow Architectures as Efficient Bifunctional Catalysts for Lithium-Oxygen Batteries.

Rational design and massive production of bifunctional catalysts with fast oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) kinetics are critical to the realization of highly efficient lithium-oxygen (Li-O2) batteries. Here, we first exploit two types of double-walled RuO2 and Mn2O3 composite fibers, i.e., (i) phase separated RuO2/Mn2O3 fiber-in-tube (RM-FIT) and (ii) multicomposite RuO2/Mn2O3 tube-in-tube (RM-TIT), by controlling ramping rate during electrospinning process. Both RM-FIT and RM-TIT exhibited excellent bifunctional electrocatalytic activities in alkaline media. The air electrodes using RM-FIT and RM-TIT showed enhanced overpotential characteristics and stable cyclability over 100 cycles in the Li-O2 cells, demonstrating high potential as efficient OER and ORR catalysts.

Ruthenium-oxide-coated sodium vanadium fluorophosphate nanowires as high-power cathode materials for sodium-ion batteries.

Sodium-ion batteries are a very promising alternative to lithium-ion batteries because of their reliance on an abundant supply of sodium salts, environmental benignity, and low cost. However, the low rate capability and poor long-term stability still hinder their practical application. A cathode material, formed of RuO2 -coated Na3 V2 O2 (PO4 )2 F nanowires, has a 50 nm diameter with the space group of I4/mmm. When used as a cathode material for Na-ion batteries, a reversible capacity of 120 mAh g(-1) at 1 C and 95 mAh g(-1) at 20 C can be achieved after 1000 charge-discharge cycles. The ultrahigh rate capability and enhanced cycling stability are comparable with high performance lithium cathodes. Combining first principles computational investigation with experimental observations, the excellent performance can be attributed to the uniform and highly conductive RuO2 coating and the preferred growth of the (002) plane in the Na3 V2 O2 (PO4 )2 F nanowires.

An All-Solid-State Ti/RuOx pH Electrode Prepared Based on the Thermal Oxidation Method.

The development of all-solid-state precise pH electrodes holds significant importance in various fields, particularly in marine scientific research. To achieve this goal, we proposed a novel fabrication technique for an all-solid-state ruthenium oxide (Ti/RuOx) pH electrode. We thin-coated the RuCl3 precursor solution on a titanium wire substrate using a heat gun repeatedly and then calcined it in a mixture of Li2CO3 and Na2O2 at 400 °C to obtain a ruthenium oxide (RuOx) film. This RuOx film was subjected to acid treatment with dilute nitric acid, and a polytetrafluoroethylene heat shrink tube was wrapped around the non-RuOx film area. Finally, the RuOx film was fully immersed in a pH 4.00 buffer solution, finalizing the electrode preparation. The RuOx film exhibits a dense and regular conical morphology. The Ti/RuOx electrode demonstrates a good near-Nernstian response slope (e.g., -59.04 mV/pH at 25 °C), high linearity (e.g., R2 = 0.9999), rapid response (<1 s), low hysteresis (<3 mV), excellent reversibility, and good repeatability in the pH range of 2.00-10.00. After full hydration, the Ti/RuOx electrode shows a potential drift of 8.5 mV and a drift rate of approximately 0.27 mV/day over a period of 25 days, indicating good long-term stability. Furthermore, the Ti/RuOx electrode exhibits robust resistance against interference from various ions and low-concentration redox substances, ensuring a long storage life (at least 280 days), and high measurement accuracy (e.g., ± 0.02 pH units) for diverse water samples, including seawater, freshwater, and tap water. This study has evaluated the potential of the Ti/RuOx electrode as a reliable and accurate tool for pH measurements in marine scientific applications.

Catalytic Activity and Electrochemical Stability of Ru1-xMxO2 (M = Zr, Nb, Ta): Computational and Experimental Study of the Oxygen Evolution Reaction.

We use computations and experiments to determine the effect of substituting zirconium, niobium, and tantalum within rutile RuO2 on the structure, oxygen evolution reaction (OER) mechanism and activity, and electrochemical stability. Calculated electronic structures altered by Zr, Nb, and Ta show surface regions of electron density depletion and accumulation, along with anisotropic lattice parameter shifts dependent on the substitution site, substituent, and concentration. Consistent with theory, X-ray photoelectron spectroscopy experiments show shifts in binding energies of O-2s, O-2p, and Ru-4d peaks due to the substituents. Experimentally, the substituted materials showed the presence of two phases with a majority phase that contains the metal substituent within the rutile phase and a second, smaller-percentage RuO2 phase. Our experimental analysis of OER activity shows Zr, Nb, and Ta substituents at 12.5 atom % induce lower activity relative to RuO2, which agrees with computing the average of all sites; however, Zr and Ta substitution at specific sites yields higher theoretical OER activity than RuO2, with Zr substitution suggesting an alternative OER mechanism. Metal dissolution predictions show the involvement of cooperative interactions among multiple surface sites and the electrolyte. Zr substitution at specific sites increases activation barriers for Ru dissolution, however, with Zr surface dissolution rates comparable to those of Ru. Experimental OER stability analysis shows lower Ru dissolution from synthesized RuO2 and Zr-substituted RuO2 compared to commercial RuO2 and comparable amounts of Zr and Ru dissolved from Zr-substituted RuO2, aligned with our calculations.

Metallic Ru─Ru Interaction in Ruthenium Oxide Enabling Durable Proton Exchange Membrane Water Electrolysis.

Developing efficient and robust electrocatalysts toward the oxygen evolution reaction (OER) is critical for proton exchange membrane water electrolysis (PEMWE). RuO2 possesses intrinsically high OER activity, but the concurrent electrochemical dissolution leads to rapid deactivation. Here a unique RuO2 catalyst containing metallic Ru─Ru interactions (m-RuO2) is reported, which maintains stability in practical PEMWE for 100 h at 60 °C and 1 A cm-2. Experimental and theoretical investigations suggest that the presence of Ru─Ru interactions significantly increases the energy barrier for the formation of RuO2(OH)2, which is a key intermediate for Ru dissolution, and hence substantially mitigates the electrochemical corrosion of m-RuO2. Meanwhile, the Ru4d band center downshifts, accordingly, ensuring the high OER activity, and the participation of lattice oxygen in the OER is also suppressed at the Ru─Ru sites, further contributing to the enhanced durability. Interestingly, such enhanced stability is also dependent on the size of metallic Ru─Ru cluster, where the energy barrier is further increased for Ru3, but is decreased for Ru5. These results highlight the significance of local coordination structure modulation on the electrochemical stability of RuO2 and open a feasible avenue toward the development of robust OER electrocatalysts for high-performance PEMWE.

Electrochemically assisted fabrication of size-exclusion films of organically modified silica and application to the voltammetry of phospholipids.

Modification of electrodes with nm-scale organically modified silica films with pores diameters controlled at 10- and 50-nm is described. An oxidation catalyst, mixed-valence ruthenium oxide with cyano crosslinks or gold nanoparticles protected by dirhodium-substituted phosophomolybdate (AuNP-Rh2PMo11), was immobilized in the pores. These systems comprise size-exclusion films at which the biological compounds, phosphatidylcholine and cardiolipin, were electrocatalytically oxidized without interference from surface-active concomitants such as bovine serum albumin. 10-nm pores were obtained by adding generation-4 poly(amidoamine) dendrimer, G4-PAMAM, to a (CH3)3SiOCH3 sol. 50-nm pores were obtained by modifying a glassy carbon electrode (GC) with a sub-monolayer film of aminopropyltriethoxylsilane, attaching 50-nm diameter poly(styrene sulfonate), PSS, spheres to the protonated amine, transferring this electrode to a (CH3)3SiOCH3 sol, and electrochemically generating hydronium at uncoated GC sites, which catalyzed ormosil growth around the PSS. Voltammetry of Fe(CN)63- and Ru(NH3)63+ demonstrated the absence of residual charge after removal of the templating agents. With the 50-nm system, the pore structure was sufficiently defined to use layer-by-layer electrostatic assembly of AuNP-Rh2PMo11 therein. Flow injection amperometry of phosphatidylcholine and cardiolipin demonstrated analytical utility of these electrodes.

Amorphous RuO2 Catalyst for Medium Size Carboxylic Acid to Alkane Dimer Selective Kolbe Electrolysis in an Aqueous Environment.

The catalytic transformation of biomass-derived volatile carboxylic acids in an aqueous environment is crucial to developing a sustainable biorefinery. To date, Kolbe electrolysis remains arguably the most effective means to convert energy-diluted aliphatic carboxylic acids (carboxylate) to alkane for biofuel production. This paper reports the use of a structurally disordered amorphous RuO2 (a-RuO2 ) that is synthesized facilely in a hydrothermal method. The a-RuO2 is highly effective towards electrocatalytic oxidative decarboxylation of hexanoic acid and is able to produce the Kolbe product, decane, with a yield 5.4 times greater than that of commercial RuO2 . A systematic study of the reaction temperature, current intensity, and electrolyte concentration reveals the enhanced Kolbe product yield is attributable to the more efficient oxidation of the carboxylate anions for the alkane dimer formation. Our work showcases a new design idea for establishing an efficient electrocatalysts for decarboxylation coupling reaction, providing a new electrocatalyst candidate for Kolbe electrolysis.