RESUMEN
Carrier distribution and dynamics in semiconductor materials often govern their physical properties that are critical to functionalities and performance in industrial applications. The continued miniaturization of electronic and photonic devices calls for tools to probe carrier behavior in semiconductors simultaneously at the picosecond time and nanometer length scales. Here, we report pump-probe optical nanoscopy in the visible-near-infrared spectral region to characterize the carrier dynamics in silicon nanostructures. By coupling experiments with the point-dipole model, we resolve the size-dependent photoexcited carrier lifetime in individual silicon nanowires. We further demonstrate local carrier decay time mapping in silicon nanostructures with a sub-50 nm spatial resolution. Our study enables the nanoimaging of ultrafast carrier kinetics, which will find promising applications in the future design of a broad range of electronic, photonic, and optoelectronic devices.
RESUMEN
There remains continued interest in improving the advanced water oxidation process [e.g., ultraviolet (UV)/hydrogen peroxide (H2O2)] for more efficient and environmentally friendly wastewater treatment. Here, we report the design, fabrication, and performance of graphene oxide (GO, on top)/nickel-doped iron oxyhydroxide (Ni:FeOOH, shell)/silicon nanowires (SiNWs, core) as a new multifunctional photocatalyst for the degradation of common pollutants like polystyrene and methylene blue through enhancing the hydroxyl radical (â¢OH) production rate of the UV/H2O2 system. The photocatalyst combines the advantages of a large surface area and light absorption characteristics of SiNWs with heterogeneous photo-Fenton active Ni:FeOOH and photocatalytically active/charge separator GO. In addition, the built-in electric field of GO/Ni:FeOOH/SiNWs facilitates the charge separation of electrons to GO and holes to Ni:FeOOH, thus boosting the photocatalytic performance. Our photocatalyst increases the â¢OH yield by 5.7 times compared with that of a blank H2O2 solution sample and also extends the light absorption spectrum to include visible light irradiation.
RESUMEN
Advanced functionalities of silicon nanowires are size-dependent and downscaling of the nanostructure often leads to higher device performances. Single-crystal silicon nanowires with diameters approaching a single unit cell are fabricated using membrane-filtrated catalyst assisted chemical etching. Atomically filtrated gold is used as uniform pattern to direct anisotropic etching of dense silicon nanowire arrays. The size of the nanowires can be controlled by engineering the molecular weight of Poly(methyl methacrylate) used to fabricate the polymer globule membranes. The smallest silicon nanowires with 0.9 nm diameters exhibit direct, and wide band gap of 3.55 eV and establishes a new record. The experimentally obtained silicon nanowires in this size fill the valuable gap below the few-nanometer regime where to date only theoretical predictions have been available. This fabrication approach could provide facile access to atomic-scale silicon, which can bring further advancement to next generation nanodevices.
RESUMEN
Alzheimer's disease (AD) is a progressive neurodegenerative disease characterized by the accumulation of amyloid beta (Aß) plaques in the brain. Aß1-42 is the main component of Aß plaque, which is toxic to neuronal cells. Si nanowires (Si NWs) have the advantages of small particle size, high specific surface area, and good biocompatibility, and have potential application prospects in suppressing Aß aggregation. In this study, we employed the vapor-liquid-solid (VLS) growth mechanism to grow Si NWs using Au nanoparticles as catalysts in a plasma-enhanced chemical vapor deposition (PECVD) system. Subsequently, these Si NWs were transferred to a phosphoric acid buffer solution (PBS). We found that Si NWs significantly reduced cell death in PC12 cells (rat adrenal pheochromocytoma cells) induced by Aß1-42 oligomers via double staining with 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) and fluorescein diacetate/propyl iodide (FDA/PI). Most importantly, pre-incubated Si NWs largely prevented Aß1-42 oligomer-induced PC12 cell death, suggesting that Si NWs exerts an anti-Aß neuroprotective effect by inhibiting Aß aggregation. The analysis of Fourier Transform Infrared (FTIR) results demonstrates that Si NWs reduce the toxicity of fibrils and oligomers by intervening in the formation of ß-sheet structures, thereby protecting the viability of nerve cells. Our findings suggest that Si NWs may be a potential therapeutic agent for AD by protecting neuronal cells from the toxicity of Aß1-42.
Asunto(s)
Péptidos beta-Amiloides , Nanocables , Fármacos Neuroprotectores , Silicio , Animales , Ratas , Enfermedad de Alzheimer/tratamiento farmacológico , Enfermedad de Alzheimer/metabolismo , Péptidos beta-Amiloides/toxicidad , Péptidos beta-Amiloides/metabolismo , Péptidos beta-Amiloides/antagonistas & inhibidores , Supervivencia Celular/efectos de los fármacos , Nanocables/química , Fármacos Neuroprotectores/farmacología , Fármacos Neuroprotectores/química , Células PC12 , Fragmentos de Péptidos/química , Fragmentos de Péptidos/toxicidad , Fragmentos de Péptidos/farmacología , Agregado de Proteínas/efectos de los fármacos , Silicio/químicaRESUMEN
Tin-containing layers with different degrees of oxidation are uniformly distributed along the length of silicon nanowires formed by a top-down method by applying metalorganic chemical vapor deposition. The electronic and atomic structure of the obtained layers is investigated by applying nondestructive surface-sensitive X-ray absorption near edge spectroscopy using synchrotron radiation. The results demonstrated, for the first time, a distribution effect of the tin-containing phases in the nanostructured silicon matrix compared to the results obtained for planar structures at the same deposition temperatures. The amount and distribution of tin-containing phases can be effectively varied and controlled by adjusting the geometric parameters (pore diameter and length) of the initial matrix of nanostructured silicon. Due to the occurrence of intense interactions between precursor molecules and decomposition by-products in the nanocapillary, as a consequence of random thermal motion of molecules in the nanocapillary, which leads to additional kinetic energy and formation of reducing agents, resulting in effective reduction of tin-based compounds to a metallic tin state for molecules with the highest penetration depth in the nanostructured silicon matrix. This effect will enable clear control of the phase distributions of functional materials in 3D matrices for a wide range of applications.
RESUMEN
The composition and atomic and electronic structure of a silicon nanowire (SiNW) array coated with tin oxide are studied at the spectromicroscopic level. SiNWs are covered from top to down with a wide bandgap tin oxide layer using a metal-organic chemical vapor deposition technique. Results obtained via scanning electron microscopy and X-ray diffraction showed that tin-oxide nanocrystals, 20 nm in size, form a continuous and highly developed surface with a complex phase composition responsible for the observed electronic structure transformation. The "one spot" combination, containing a chemically sensitive morphology and spectroscopic data, is examined via photoemission electron microscopy in the X-ray absorption near-edge structure spectroscopy (XANES) mode. The observed spectromicroscopy results showed that the entire SiNW surface is covered with a tin(IV) oxide layer and traces of tin(II) oxide and metallic tin phases. The deviation from stoichiometric SnO2 leads to the formation of the density of states sub-band in the atop tin oxide layer bandgap close to the bottom of the SnO2 conduction band. These observations open up the possibility of the precise surface electronic structures estimation using photo-electron microscopy in XANES mode.
RESUMEN
Stretching elastomer bands to accumulate strain energy, for a sudden projectile launching, has been an old hunting skill that will continue to find new applications in miniaturized worlds. In this work, we explore the use of highly resilient and geometry-tailored ultrathin crystalline silicon nanowires (SiNWs) as elastic medium to fabricate the first, and the smallest, mechanical slingshot. These NW-morphed slingshots were first grown on a planar surface, with desired layout, and then mounted upon standing pillar frames, with a unique self-hooking structure that allows for a facile and reliable assembly, loading and shooting maneuver of microsphere payloads. Impressively, the elastic spring design can help to store 10 times more strain energy into the NW springs, compared with the straight ones under the same pulling force, which has been strong enough to overcome the sticky van der Waals (vdW) force at the touching interfaces that otherwise will hinder a reliable releasing onto soft surface with low-surface energy or adhesion force, and to achieve a directional shooting delivery of precise amount of tiny payload units onto delicate target with the least impact damage. This NW-morphing construction strategy also provides a generic protocol/platform to fast design, prototype, and deploy new nanoelectromechanical and biological applications at extremely low costs.
RESUMEN
Nanowire-based technological advancements thrive in various fields, including energy generation and storage, sensors, and electronics. Among the identified nanowires, silicon nanowires (SiNWs) attract much attention as they possess unique features, including high surface-to-volume ratio, high electron mobility, bio-compatibility, anti-reflection, and elasticity. They were tested in domains of energy generation (thermoelectric, photo-voltaic, photoelectrochemical), storage (lithium-ion battery (LIB) anodes, super capacitors), and sensing (bio-molecules, gas, light, etc). These nano-structures were found to improve the performance of the system in terms of efficiency, stability, sensitivity, selectivity, cost, rapidity, and reliability. This review article scans and summarizes the significant developments that occurred in the last decade concerning the application of SiNWs in the fields of thermoelectric, photovoltaic, and photoelectrochemical power generation, storage of energy using LIB anodes, biosensing, and disease diagnostics, gas and pH sensing, photodetection, physical sensing, and electronics. The functionalization of SiNWs with various nanomaterials and the formation of heterostructures for achieving improved characteristics are discussed. This article will be helpful to researchers in the field of nanotechnology about various possible applications and improvements that can be realized using SiNW.
RESUMEN
As a new type of one-dimensional semiconductor nanometer material, silicon nanowires (SiNWs) possess good application prospects in the field of biomedical sensing. SiNWs have excellent electronic properties for improving the detection sensitivity of biosensors. The combination of SiNWs and field effect transistors (FETs) formed one special biosensor with high sensitivity and target selectivity in real-time and label-free. Recently, SiNW-FETs have received more attention in fields of biomedical detection. Here, we give a critical review of the progress of SiNW-FETs, in particular, about the reversible surface modification methods. Moreover, we summarized the applications of SiNW-FETs in DNA, protein, and microbial detection. We also discuss the related working principle and technical approaches. Our review provides an extensive discussion for studying the challenges in the future development of SiNW-FETs.
Asunto(s)
Técnicas Biosensibles , Nanocables , Transistores Electrónicos , Silicio , Semiconductores , Técnicas Biosensibles/métodosRESUMEN
The search for improved transducers to fabricate better-performing (bio)sensors is a challenging but rewarding endeavor aiming to better diagnose and treat diseases. In this paper, we report on the decoration of a dense vertical array of ultrathin silicon nanowires (Si NWs), produced by metal-assisted chemical etching, with 20 nm gold nanoparticles (Au NPs) for surface-enhanced Raman scattering (SERS) applications. To optimize the production of a uniform 3D SERS active platform, we tested different Si NW surface functionalizations with various alkoxysilanes before Au decoration. Scanning electron microscopy investigations confirm that Au NPs decorate both bare and (3-glycidiloxypropyl)trimethoxysilane (GPTMS)-modified Si NWs with a high surface coverage uniformity. The SERS response of the decorated NWs was probed using a model dye system (methylene blue; MB) at 633 and 785 nm excitation wavelengths. The GPTMS-modified NWs present the highest enhancements of 2.9 and 2.6 for the 450 cm-1 and 1625 cm-1 peaks under 785 nm excitation and of 10.8 and 5.3 for the 450 cm-1 and 1625 cm-1 peaks under 633 nm excitation. These results demonstrate the perspective role of Si NWs decorated with Au NPs as a low-cost 3D SERS platform.
Asunto(s)
Nanopartículas del Metal , Nanocables , Oro , Microscopía Electrónica de Rastreo , SilicioRESUMEN
Acetone commonly exists in daily life and is harmful to human health, therefore the convenient and sensitive monitoring of acetone is highly desired. In addition, flexible sensors have the advantages of light-weight, conformal attachable to irregular shapes, etc. In this study, we fabricated high performance flexible silicon nanowires (SiNWs) sensor for acetone detection by transferring the monocrystalline Si film and metal-assisted chemical etching method on polyethylene terephthalate (PET). The SiNWs sensor enabled detection of gaseous acetone with a concentration as low as 0.1 parts per million (ppm) at flat and bending states. The flexible SiNWs sensor was compatible with the CMOS process and exhibited good sensitivity, selectivity and repeatability for acetone detection at room temperature. The flexible sensor showed performance improvement under mechanical bending condition and the underlying mechanism was discussed. The results demonstrated the good potential of the flexible SiNWs sensor for the applications of wearable devices in environmental safety, food quality, and healthcare.
RESUMEN
In this study, we perform reconfigurable n- and p-channel operations of a tri-top-gate field-effect transistor (FET) made of a p+-i-n+silicon nanowire (SiNW). In the reconfigurable FET (RFET), two polarity gates and one control gate induce virtual electrostatic doping in the SiNW channel. The polarity gates are electrically connected to each other and program the channel type, while the control gate modulates the flow of charge carriers in the SiNW channel. The SiNW RFET features simple device design, symmetrical electrical characteristics in the n- and p-channel operation modes using p+-i-n+diode characteristics, and both operation modes exhibit high ON/OFF ratios (â¼106) and high ON currents (â¼1µAµm-1). The proposed device is demonstrated experimentally using a fully CMOS-compatible top-down processes.
RESUMEN
Traditional bioelectronics, primarily comprised of nonliving synthetic materials, lack cellular behaviors such as adaptability and motility. This shortcoming results in mechanically invasive devices and nonnatural signal transduction across cells and tissues. Moreover, resolving heterocellular electrical communication in vivo is extremely limited due to the invasiveness of traditional interconnected electrical probes. In this paper, we present a cell-silicon hybrid that integrates native cellular behavior (e.g., gap junction formation and biosignal processing) with nongenetically enabled photosensitivity. This hybrid configuration allows interconnect-free cellular modulation with subcellular spatial resolution for bioelectric studies. Specifically, we hybridize cardiac myofibroblasts with silicon nanowires and use these engineered hybrids to synchronize the electrical activity of cardiomyocytes, studying heterocellular bioelectric coupling in vitro. Thereafter, we inject the engineered myofibroblasts into heart tissues and show their ability to seamlessly integrate into contractile tissues in vivo. Finally, we apply local photostimulation with high cell specificity to tackle a long-standing debate regarding the existence of myofibroblast-cardiomyocyte electrical coupling in vivo.
Asunto(s)
Miocitos Cardíacos/química , Miofibroblastos/química , Silicio/química , Animales , Bioingeniería , Células Cultivadas , Fenómenos Electrofisiológicos , Uniones Comunicantes/fisiología , Humanos , Ratones , Miocitos Cardíacos/fisiología , Miofibroblastos/fisiología , Nanocables/química , Transducción de SeñalRESUMEN
Silicon nanowires (SiNWs) are known to exhibit a large piezoresistance (PZR) effect, making them suitable for various sensing applications. Here, we report the results of a PZR investigation on randomly distributed and interconnected vertical silicon nanowire arrays as a pressure sensor. The samples were produced from p-type (100) Si wafers using a silver catalyzed top-down etching process. The piezoresistance response of these SiNW arrays was analyzed by measuring their I-V characteristics under applied uniaxial as well as isostatic pressure. The interconnected SiNWs exhibit increased mechanical stability in comparison with separated or periodic nanowires. The repeatability of the fabrication process and statistical distribution of measurements were also tested on several samples from different batches. A sensing resolution down to roughly 1m pressure was observed with uniaxial force application, and more than two orders of magnitude resistance variation were determined for isostatic pressure below atmospheric pressure.
RESUMEN
The optical properties of silicon nanowire arrays (SiNWs) are closely related to surface morphology due to quantum effects and quantum confinement effects of the existing semiconductor nanocrystal. In order to explore the influence of the diameters and distribution density of nanowires on the light absorption in the visible to near infrared band, we report the highly efficient method of multiple replication of versatile homogeneous Au films from porous anodic aluminum oxide (AAO) membranes by ion sputtering as etching catalysts; the monocrystalline silicon is etched along the growth templates in a fixed proportion chemical solution to form homogeneous ordered arrays of different morphology and distributions on the surface. In this system, we demonstrate that the synthesized nanostructure arrays can be tuned to exhibit different optical characteristics in the test wavelength range by adjusting the structural parameters of AAO membranes.
RESUMEN
Air quality monitoring is an increasingly debated topic nowadays. The increasing spillage of waste products released into the environment has contributed to the increase in air pollution. Consequently, the production of increasingly performing devices in air monitoring is increasingly in demand. In this scenario, the attention dedicated to workplace safety monitoring has led to the developing and improving of new sensors. Despite technological advancements, sensors based on nanostructured materials are difficult to introduce into the manufacturing flow due to the high costs of the processes and the approaches that are incompatible with the microelectronics industry. The synthesis of a low-cost ultra-thin silicon nanowires (Si NWs)-based sensor is here reported, which allows us the detection of various dangerous gases such as acetone, ethanol, and the ammonia test as a proof of concept in a nitrogen-based mixture. A modified metal-assisted chemical etching (MACE) approach enables to obtain ultra-thin Si NWs by a cost-effective, rapid and industrially compatible process that exhibit an intense light emission at room temperature. All these gases are common substances that we find not only in research or industrial laboratories, but also in our daily life and can pose a serious danger to health, even at small concentrations of a few ppm. The exploitation of the Si NWs optical and electrical properties for the detection of low concentrations of these gases through their photoluminescence and resistance changes will be shown in a nitrogen-based gas mixture. These sensing platforms give fast and reversible responses with both optical and electrical transductions. These high performances and the scalable synthesis of Si NWs could pave the way for market-competitive sensors for ambient air quality monitoring.
Asunto(s)
Contaminación del Aire , Nanocables , Nanocables/química , Silicio/química , Gases/análisis , Control de Calidad , NitrógenoRESUMEN
Wearable sensors that can mimic functionalities of human bodies have attracted intense recent attention. However, research on wearable airflow sensors is still lagging behind. Herein, we report a biomimetic hair sensor based on a single ultralong silicon nanowire (SiNW-BHS) for airflow detection. In our device, the SiNW can provide both mechanical and electrical responses in airflow, which enables a simple and compact design. The SiNW-BHSs can detect airflow with a low detection limit (<0.15 m/s) and a record-high response speed (response time <40 ms). The compact design of the SiNW-BHSs also enables easy integration of an array of devices onto a flexible substrate to mimic human skin to provide comprehensive airflow information including wind speed, incident position, incident angle, and so forth. This work provides novel-designed BHSs for ultrafast and highly sensitive airflow detection, showing great potential for applications such as e-skins, wearable electronics, and robotics.
Asunto(s)
Técnicas Biosensibles , Nanocables , Biomimética , Electrónica , Cabello , Humanos , SilicioRESUMEN
Dynamic range quantifies the linear operation regime available in nanomechanical resonators. Nonlinearities dominate the response of flexural beams in the limit of very high aspect ratio and very small diameter, which leads to expectation of low dynamic range for nanowire resonators in general. However, the highest achievable dynamic range for nanowire resonators with practical dimensions remains to be determined. We report dynamic range measurements on singly clamped silicon nanowire resonators reaching remarkably high values of up to 90 dB obtained with a simple harmonic actuation scheme. We explain these measurements by a comprehensive theoretical examination of dynamic range in singly clamped flexural beams including the effect of tapering, a usual feature of semiconductor nanowires. Our analysis reveals the nanowire characteristics required for broad linear operation, and given the relationship between dynamic range and mass sensing performance, it also enables analytical determination of mass detection limits, reaching atomic-scale resolution for feasible nanowires.
RESUMEN
Growing high quality silicon nanowires (SiNWs) at elevated temperature on cooler polymer films seems to be contradictive but highly desirable for building high performance flexible and wearable electronics. In this work, we demonstrate a superfast (vnw > 3.5 µm·s-1) growth of high quality SiNWs on polymer/glass substrates, powered by self-selected laser at 808 nm heating of indium catalyst droplets that absorb amorphous Si layer to produce SiNWs. Because of the tiny heat capacity of the nanodroplets, the SiNW growth can be quickly heated up and frozen via rapid laser ON/OFF switching, enabling a deterministic diameter modulation in the ultralong SiNWs. Finally, prototype field effect transistors are also fabricated upon the laser-droplet-heating grown SiNWs with a high Ion/Ioff ratio of >104 and reasonable subthreshold swing of 386 mV·dec-1, opening a generic new route to integrate high-quality NW channels directly upon large area and lightweight polymer substrates for developing high-performance flexible electronics.
RESUMEN
Silicon nanowires (NWs) are appealing building blocks for low-cost novel concept devices with improved performances. In this research paper, we realized a hybrid platform combining an array of vertically oriented Si NWs with different types of bucky gels, obtained from carbon nanotubes (CNT) dispersed into an ionic liquid (IL) matrix. Three types of CNT bucky gels were obtained from imidazolium-based ionic liquids (BMIM-I, BIMI-BF4, and BMIM-Tf2N) and semiconductive CNTs, whose structural and optical responses to the hybrid platforms were analyzed and compared. We investigated the electrical response of the IL-CNT/NW hybrid junctions in dark and under illumination for each platform and its correlation to the ionic liquid characteristics and charge mobility. The reported results confirm the attractiveness of such IL-CNT/NW hybrid platforms as novel light-responsive materials for photovoltaic applications. In particular, our best performing cell reported a short-circuit current density of 5.6 mA/cm2 and an open-circuit voltage of 0.53 V.