Enhanced iontophoretic delivery of buspirone hydrochloride across human skin using chemical enhancers.

Buspirone hydrochloride (BH) is a structurally and pharmacologically unique anxiolytic that is used to treat a variety of different anxiety conditions. The marketed product is named BuSpar. The in vitro iontophoretic delivery of BH through human skin was investigated in order to evaluate the feasibility of delivering a therapeutic dose of BH by this route. We also examined the influence of co-formulations of chemical enhancers (Azone, oleic acid, menthone, cineole, and terpineol) on BH permeation, both without iontophoresis and with iontophoresis-to look for possible synergistic effects. By applying iontophoresis at 0.5 mA/cm(2), it was possible to achieve a BH steady state flux of approximately 350 microg/cm(2)h, which would be therapeutically effective if clinically duplicated. Importantly, 24 h of iontophoresis at 0.5 mA/cm(2) did not affect skin morphology and after the current was switched off, the skin's permeability to BH rapidly reverted to its pre-iontophoretic level. Without iontophoreis, BH transdermal flux was significantly enhanced by the application of 2.5% (v/v) concentrations of Azone, oleic acid, or menthone but not cineole or terpineol. Furthermore, this paper identified a synergistic transport enhancement effect developing when very low current (0.025 mA/cm(2)) iontophoresis was applied in conjunction with Azone treatment.

Iontophoretic transdermal delivery of buspirone hydrochloride in hairless mouse skin.

The transdermal delivery of buspirone hydrochloride across hairless mouse skin and the combined effect of iontophoresis and terpene enhancers were evaluated in vitro using Franz diffusion cells. Iontophoretic delivery was optimized by evaluating the effect of drug concentration, current density, and pH of the vehicle solution. Increasing the current density from 0.05 to 0.1 mA/cm2 resulted in doubling of the iontophoretic flux of buspirone hydrochloride, while increasing drug concentration from 1% to 2% had no effect on flux. Using phosphate buffer to adjust the pH of the drug solution decreased the buspirone hydrochloride iontophoretic flux relative to water solutions. Incorporating buspirone hydrochloride into ethanol:water (50:50 vol/vol) based gel formulations using carboxymethylcellulose and hydroxypropylmethylcellulose had no effect on iontophoretic delivery. Incorporation of three terpene enhancers (menthol, cineole, and terpineol) into the gel resulted in a synergistic effect when combined with iontophoresis. Menthol was the most active enhancer, and when combined with iontophoresis it was possible to deliver 10 mg/cm2/day of buspirone hydrochloride.

A photo-crosslinked poly(vinyl alcohol) hydrogel growth factor release vehicle for wound healing applications.

The objective of this study was to develop and evaluate a hydrogel vehicle for sustained release of growth factors for wound healing applications. Hydrogels were fabricated using ultraviolet photo-crosslinking of acrylamide-functionalized nondegradable poly(vinyl alcohol) (PVA). Protein permeability was initially assessed using trypsin inhibitor (TI), a 21 000 MW model protein drug. TI permeability was altered by changing the solids content of the gel and by adding hydrophilic PVA fillers. As the PVA content increased from 10% to 20%, protein flux decreased, with no TI permeating through 20% PVA hydrogels. Further increase in model drug release was achieved by incorporating hydrophilic PVA fillers into the hydrogel. As filler molecular weight increased, TI flux increased. The mechanism for this is most likely an alteration in protein/gel interactions and transient variations in water content. The percent protein released was also altered by varying protein loading concentration. Release studies conducted using growth factor in vehicles with hydrophilic filler showed sustained release of platelet-derived growth factor (PDGF-beta,beta) for up to 3 days compared with less than 24 hours in the controls. In vitro bioactivity was demonstrated by doubling of normal human dermal fibroblast numbers when exposed to growth factor-loaded vehicle compared to control. The release vehicle developed in this study uses a rapid and simple fabrication method, and protein release can be tailored by modifying solid content, incorporating biocompatible hydrophilic fillers, and varying protein loading concentration.

Transcutaneous delivery and thermostability of a dry trivalent inactivated influenza vaccine patch.

A patch containing a trivalent inactivated influenza vaccine (TIV) was prepared in a dried, stabilized formulation for transcutaneous delivery. When used in a guinea pig immunogenicity model, the dry patch was as effective as a wet TIV patch in inducing serum anti-influenza IgG antibodies. When the dry TIV patch was administered with LT as an adjuvant, a robust immune response was obtained that was comparable with or better than an injected TIV vaccine. When stored sealed in a nitrogen-purged foil, the dry TIV patch was stable for 12 months, as measured by HA content, under both refrigerated and room temperature conditions. Moreover, the immunological potency of the vaccine product was not affected by long-term storage. The dry TIV patch was also thermostable against three cycles of alternating low-to-high temperatures of -20/25 and -20/40 degrees C, and under short-term temperature stress conditions. These studies indicate that the dry TIV patch product can tolerate unexpected environmental stresses that may be encountered during shipping and distribution. Because of its effectiveness in vaccine delivery and its superior thermostable characteristics, the dry TIV patch represents a major advance for needle-free influenza vaccination.