Water Interactions with Hydrophobic versus Hydrophilic Nanosilica.

It is well-known that interaction of hydrophobic powders with water is weak, and upon mixing, they typically form separated phases. Preparation of hydrophobic nanosilica AM1 with a relatively large content of bound water with no formation of separated phases was the aim of this study. Unmodified nanosilica A-300 and initial AM1 (A-300 completely hydrophobized by dimethyldichlorosilane), compacted A-300 (cA-300), and compacted AM1 (cAM1) containing 50-58 wt % of bound water were studied using low-temperature 1H NMR spectroscopy, thermogravimetry, infrared spectroscopy, microscopy, small-angle X-ray scattering, nitrogen adsorption, and theoretical modeling. After mechanical activation (∼20 atm) upon stirring of AM1/water mixture at the degree of hydration h = 1.0 or 1.4 g of distilled water per gram of dry silica, all water is bound and the blend has the bulk density of 0.7 g/cm3. The temperature and interfacial behaviors of bound water depend strongly on a dispersion media type (air, chloroform, and chloroform with trifluoroacetic acid (4:1)) because the boundary area between immiscible water and chloroform should be minimal. Water and chloroform molecules are of different sizes affecting their distribution in pores (voids between silica nanoparticles in their aggregates) of different sizes. Structural, morphological, and textural characteristics of silicas, and environmental features affect not only the distribution of bound water, but also the amounts of strongly (frozen at T < 260 K) and weakly (frozen at 260 K < T < 273 K) bound and strongly (chemical shift δH = 4-6 ppm) and weakly (δH = 1-2 ppm) associated waters. Despite the changes in the characteristics of cAM1, it demonstrates a flotation effect. The developed system with cAM1/bound water could be of interest from a practical point of view due to controlled interactions with aqueous surroundings.

Kinetics of Valeric Acid Ketonization and Ketenization in Catalytic Pyrolysis on Nanosized SiO2 , γ-Al2 O3 , CeO2 /SiO2 , Al2 O3 /SiO2 and TiO2 /SiO2.

Valeric acid is an important renewable platform chemical that can be produced efficiently from lignocellulosic biomass. Upgrading of valeric acid by catalytic pyrolysis has the potential to produce value added biofuels and chemicals on an industrial scale. Understanding the different mechanisms involved in the thermal transformations of valeric acid on the surface of nanometer-sized oxides is important for the development of efficient heterogeneously catalyzed pyrolytic conversion techniques. In this work, the thermal decomposition of valeric acid on the surface of nanoscale SiO2 , γ-Al2 O3 , CeO2 /SiO2 , Al2 O3 /SiO2 and TiO2 /SiO2 has been investigated by temperature-programmed desorption mass spectrometry (TPD MS). Fourier transform infrared spectroscopy (FTIR) has also been used to investigate the structure of valeric acid complexes on the oxide surfaces. Two main products of pyrolytic conversion were observed to be formed depending on the nano-catalyst used-dibutylketone and propylketene. Mechanisms of ketene and ketone formation from chemisorbed fragments of valeric acid are proposed and the kinetic parameters of the corresponding reactions were calculated. It was found that the activation energy of ketenization decreases in the order SiO2 >γ-Al2 O3 >TiO2 /SiO2 >Al2 O3 /SiO2 , and the activation energy of ketonization decreases in the order γ-Al2 O3 >CeO2 /SiO2 . Nano-oxide CeO2 /SiO2 was found to selectively catalyze the ketonization reaction.

Surroundings effects on the interfacial and temperature behaviors of NaOH/water bound to hydrophilic and hydrophobic nanosilicas.

HYPOTHESIS: It has been assumed that the temperature and interfacial behaviors of concentrated alkali solutions under confined space effects may depend on adsorbent surface structure, hydrophilicity/hydrophobicity, porosity of solids, and dispersion media properties causing kosmotropic or chaotropic effects onto hydrogen bond network (HBN) in bound water and NaOH solution. EXPERIMENTS: To analyze these effects, systems with NaOH/water (0.1 g/g/0.1 g/g) deposited onto compacted hydrophilic (A-300) and hydrophobic (AM1) nanosilicas were studied using 1H NMR spectroscopy (215-287 K). The materials were characterized using several experimental and theoretical methods. FINDINGS: It has been shown that bound water and water/NaOH represent various clusters and domains whose characteristics depend strongly on nanosilica hydrophilicity/hydrophobicity, dispersion media (air, CDCl3, DMSO, CDCl3/DMSO), subsequent or simultaneous deposition of NaOH and water, and temperature. Water amount (0.1 g/g) was selected too small to completely dissolve NaOH (0.1 g/g) under confined space effects and low temperatures. Chaotropic hydrophobic AM1 and CDCl3 enhance water clusterization and HBN disorder (weakly associated water, WAW appears) in contrast to kosmotropic hydrophilic A-300, NaOH, and DMSO reducing the clusterization and HBN disorder in bound water (WAW disappears). Several aspects related to the interfacial and temperature behaviors of water and co-adsorbates bound to the nanosilicas were elucidated.

Interfacial behavior of polar and nonpolar frozen/unfrozen liquids interacting with hydrophilic and hydrophobic nanosilicas alone and in blends.

HYPOTHESIS: Various nanosilica characteristics depend on hydrophobization strongly affecting interfacial phenomena. Is it possible to prepare hydrophilic samples with hydrophobic silica (AM1) alone and in blends with hydrophilic one (A-300)? It can be done with addition of a small amount of water to the powders which then are mechanically treated. EXPERIMENTS: Nanosilicas were characterized using adsorption, desorption, microscopic, spectroscopic, and quantum chemistry methods. 1H NMR spectroscopy and cryoporometry were applied to AM1 and AM1/A-300 blends wetted and mechanically treated. Wetted blends were studied with additions of n-decane and chloroform-d. FINDINGS: The powders wetted at h = 0.3-3.0 g of water per gram of dry solids have increased bulk density. Samples are in gel-like state at h = 4-5 g/g. Water interaction energy with nanoparticles nonmonotonically depends on h (maximal at h = 3 g/g). Upon mechanical treatment of wetted blends (h < 1.5 g/g), separated AM1 structures are absent. At greater h values, blend reorganization occurs to form AM1 aggregates covered by A-300 shells. Organics can displace water from mesovoids toward narrower pores inaccessible for larger molecules or into larger voids to reduce the contact area between immiscible liquids. Freezing point depression caused by confined space and dissolution effects is affected by the blend organization.

Nanosized copper(ii) oxide/silica for catalytic generation of nitric oxide from S-nitrosothiols.

Nitric oxide NO, mediates inflammatory and thrombotic processes and designing biomaterials capable of releasing NO in contact with biological tissues is considered to be a major factor aimed at improving their bio- and haemocompatibility and antibacterial properties. Their NO-releasing capacity however is limited by the amount of the NO-containing substance incorporated in the bulk or immobilised on the surface of a biomaterial. An alternative approach is based on the design of a material generating nitric oxide from endogenous NO bearing metabolites by their catalytic decomposition. It offers, at least in theory, an unlimited source of NO for as long as the material remains in contact with blood and the catalyst maintains its activity. In this paper we studied the catalytic properties of novel nanostructured CuO/SiO2 catalysts in generating NO by decomposition of S-nitrosoglutathione (GSNO) in vitro. CuO/SiO2 catalysts with different CuO loadings were synthesized by chemisorption of copper(ii) acetylacetonate on fumed nanosilica followed by calcination. CuO content was controlled by a number of chemisorption-calcination cycles. Fourier-transform infrared spectroscopy and thermogravimetric analysis confirmed the formation of CuO/SiO2 nanoparticles (NPs) with particle size of CuO phase in the range from 71 to 88 nm. Scanning electron microscopy images revealed a uniform distribution of NPs without their sintering or agglomeration. All the materials of the CuO/SiO2 NP series exhibited NO-generating activity from GSNO confirmed by the Griess assay and by measuring the concentration of nitrite and nitrate anions in model solutions such as phosphate buffered saline and bovine serum. This activity is dependent on the material specific surface area and CuO exposure on the surface rather than CuO bulk content. The rate of NO production increased at higher initial concentration of the NO-bearing substrate studied in the range between 0.01 mM and 1.0 mM RSNO, which covers its physiological level. CuO/SiO2 NPs can be used to design polymers with NO generating properties at blood-biomaterial interface which are expected to have improved biocompatibility thus enhancing their potential for medical applications such as surgical tubing, peripheral venous catheters, auxiliary blood circulation devices and drug-eluting balloons.

Nanooxide/Polymer Composites with Silica@PDMS and Ceria-Zirconia-Silica@PDMS: Textural, Morphological, and Hydrophilic/Hydrophobic Features.

SiO2@PDMS and CeO2-ZrO2-SiO2@PDMS nanocomposites were prepared and studied using nitrogen adsorption-desorption, Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), measurements of advancing and receding contact angles with water, and microcalorimetry. The pore size distributions indicate that the textural characteristics change after oxide modification by poly(dimethylsiloxane) (PDMS). Composites are characterized by mainly mesoporosity and macroporosity of aggregates of oxide nanoparticles or oxide@PDMS nanoparticles and their agglomerates. The FT-IR spectra show that PDMS molecules cover well the oxide surface, since the intensity of the band of free silanols at 3748 cm-1 decreases with increasing PDMS concentration and it is absent in the IR spectrum at C PDMS ≥ 20 wt% that occurs due to the hydrogen bonding of the PDMS molecules to the surface hydroxyls. SEM images reveal that the inter-particle voids are gradually filled and aggregates are re-arranged and increase from 20 to 200 nm in size with the increasing polymer concentration. The highest hydrophobicity (contact angle θ = 140° at C PDMS = 20-40 wt%) is obtained for the CeO2-ZrO2-SiO2@PDMS nanocomposites. The heat of composite immersion in water shows a tendency to decrease with increasing PDMS concentration.

Synthesis and Examination of Nanocomposites Based on Poly(2-hydroxyethyl methacrylate) for Medicinal Use.

Preparation of poly(2-hydroxyethyl methacrylate) (PHEMA) based nanocomposites using different approaches such as synthesis with water as the porogen, filling of polymer matrix by silica and formation of interpenetrating polymer networks with polyurethane was demonstrated. Incorporation of various biologically active compounds (BAC) such as metronidazole, decamethoxin, zinc sulphate, silver nitrate or amino acids glycine and tryptophan into nanocomposites was achieved. BAC were introduced into the polymer matrix either (1) directly, or (2) with a solution of colloidal silica, or (3) through immobilization on silica (sol-densil). Morphology of prepared materials was investigated by laser scanning microscopy and low-vacuum scanning electron microscopy. In vacuum freeze-drying, prior imaging was proposed for improving visualization of the porous structure of composites. The interaction between PHEMA matrix and silica filler was investigated by IR spectroscopy. Adsorption of 2-hydroxyethyl methacrylate and BAC from aqueous solution on the silica surface was also examined. Phase composition and thermal stability of composites were studied by the differential thermogravimetry/differential thermal analysis. Release of BAC into water medium from prepared composites were shown to depend on the synthetic method and differed significantly. Obtained PHEMA-base materials which are characterized by controlled release of BAC have a strong potential for application in manufacturing of different surgical devices like implants, catheters and drainages.

Preparation and Characterization of Silica-Enoxil Nanobiocomposites.

Silica-Enoxil nanobiocomposites with 13 %w of Enoxil were prepared either by mechanical mixing of corresponding powders or by sorptive modification of fumed silica powder with aqueous Enoxil solution under fluidized bed conditions. The interaction of fumed silica with Enoxil and the properties of silica-Enoxil composites have been investigated using IR spectroscopy, thermogravimetric analysis, and quantum chemistry methods, as well as by means of water absorption, Enoxil desorption, and 2,2-diphenyl-1-picrylhydrazyl (DPPH) test. It has been shown that the main biomolecules of Enoxil composition interact with silica involving their hydroxyl groups and surface silanol groups. The water absorption of silica-Enoxil nanocomposites was found to be less than that for the individual components. The Enoxil biomolecules are readily and completely desorbed from silica surface into water, and the antioxidant activity of desorbed Enoxil is practically the same as that for the just dissolved one.

Dimethylsilanone Generation from Pyrolysis of Polysiloxanes Filled with Nanosized Silica and Ceria/Silica.

Temperature-programmed desorption mass spectrometry (TPD MS) was used to study the pyrolysis of PDMS and its composites with nanosized silica and ceria/silica. The results suggest that the elusive organosilicon compound, dimethylsilanone, is generated from PDMS over a broad temperature range (in some cases starting at 70 °C). The presence of nano-oxides catalyzes this process. Ions characteristic of the fragmentation of dimethylsilanone under electron ionization are assigned with the aid of DFT structure calculations. Possible reaction mechanisms for dimethylsilanone generation are discussed in the context of the calculated kinetic parameters. Observed accompanying products of PDMS pyrolysis, such as tetramethylcyclodisiloxane and hexamethylcyclotrisiloxane, indicate that multiple channels are involved in the dimethylsilanone release.

A TPD-MS study of the interaction of coumarins and their heterocyclic derivatives with a surface of fumed silica and nanosized oxides CeO2/SiO2, TiO2/SiO2, Al2O3/SiO2.

The interactions between coumarins and the surface of fumed SiO(2), CeO(2)/SiO(2), TiO(2)/SiO(2) and Al(2)O(3)/SiO(2) were assessed by means of temperature-programmed desorption mass spectrometry. The different stages of the thermolysis of coumarin were identified and an analysis of the underlying reactions was performed. The kinetic parameters of the involved reactions were thus obtained. The decomposition of thiazolyl-substituted coumarins was found to proceed through a 'thiazole-thiazine' ring expansion in the adsorbed state. A linear correlation between the sigma constants (Sigma sigma) of the coumarin substituents and the activation energy of CO(2) formation was obtained.