RESUMO
A compact back-end interface for silicon photomultipliers (SiPMs) implementing Zener diode-based temperature compensation has been developed for the remote detection of beta and gamma radiation. Remote detection is facilitated by the development of an efficient data management system utilising MySQL database storage for recording periodic spectra data for wireless access over a private Wi-Fi network. A trapezoidal peak shaping algorithm has been implemented on an FPGA for the continuous conversation of pulses from the SiPM, signifying the detection of a radiological particle, into spectra. This system has been designed to fit within a 46 mm cylindrical diameter for in situ characterization, and can be attached to one or more SiPMs used in conjunction with a range of scintillators. LED blink tests have been used to optimise the trapezoidal shaper coefficients to maximise the resolution of the recorded spectra. Experiments with an array of SiPMs integrated with a NaI(Tl) scintillator exposed to sealed sources of Co-60, Cs-137, Na-22 and Am-241 have shown that the detector achieves a peak efficiency of 27.09 ± 0.13% for a gamma peak at 59.54 keV produced by Am-241, and a minimum energy resolution (Delta E/E) of 4.27 ± 1.16% for the 1332.5 keV gamma peak from Co-60.
RESUMO
Biomaterials capable of precisely controlling the delivery of agrochemicals/biologics/drugs/fragrances have significant markets in the agriscience/healthcare industries. Here, we report the development of degradable electroactive polymers and their application for the controlled delivery of a clinically relevant drug (the anti-inflammatory dexamethasone phosphate, DMP). Electroactive copolymers composed of blocks of polycaprolactone (PCL) and naturally occurring electroactive pyrrole oligomers (e.g., bilirubin, biliverdin, and hemin) were prepared and solution-processed to produce films (optionally doped with DMP). A combination of in silico/in vitro/in vivo studies demonstrated the cytocompatibility of the polymers. The release of DMP in response to the application of an electrical stimulus was observed to be enhanced by ca. 10-30% relative to the passive release from nonstimulated samples in vitro. Such stimuli-responsive biomaterials have the potential for integration devices capable of delivering a variety of molecules for technical/medical applications.
Assuntos
Materiais Biocompatíveis , Polímeros , Eletricidade , PirróisRESUMO
Autonomous analysis of plants, such as for phenotyping and health monitoring etc., often requires the reliable identification and localization of single leaves, a task complicated by their complex and variable shape. Robotic sensor platforms commonly use depth sensors that rely on either infrared light or ultrasound, in addition to imaging. However, infrared methods have the disadvantage of being affected by the presence of ambient light, and ultrasound methods generally have too wide a field of view, making them ineffective for measuring complex and intricate structures. Alternatives may include stereoscopic or structured light scanners, but these can be costly and overly complex to implement. This article presents a fully computer-vision based solution capable of estimating the three-dimensional location of all leaves of a subject plant with the use of a single digital camera autonomously positioned by a three-axis linear robot. A custom trained neural network was used to classify leaves captured in multiple images taken of a subject plant. Parallax calculations were applied to predict leaf depth, and from this, the three-dimensional position. This article demonstrates proof of concept of the method, and initial tests with positioned leaves suggest an expected error of 20 mm. Future modifications are identified to further improve accuracy and utility across different plant canopies.
Assuntos
Algoritmos , Folhas de Planta , Robótica , Computadores , PlantasRESUMO
Global concern for the illicit transportation and trafficking of nuclear materials and other radioactive sources is on the rise, with efficient and rapid security and non-proliferation technologies in more demand than ever. Many factors contribute to this issue, including the increasing number of terrorist cells, gaps in security networks, politically unstable states across the globe and the black-market trading of radioactive sources to unknown parties. The use of passive gamma-ray and neutron detection and imaging technologies in security-sensitive areas and ports has had more impact than most other techniques in detecting and deterring illicit transportation and trafficking of illegal radioactive materials. This work reviews and critically evaluates these techniques as currently utilised within national security and non-proliferation applications and proposes likely avenues of development.
RESUMO
On the Sellafield site there are several legacy storage tanks and silos containing sludge of uncertain properties. While there are efforts to determine the chemical and radiological properties of the sludge, to clean out and decommission these vessels, the physical properties need to be ascertained as well. Shear behaviour, density and temperature are the key parameters to be understood before decommissioning activities commence. However, limited access, the congested nature of the tanks and presence of radioactive, hazardous substances severely limit sampling and usage of sophisticated characterisation devices within these tanks and therefore, these properties remain uncertain. This paper describes the development of a cheap, compact, and robust device to analyse the rheological properties of sludge, without the need to extract materials from the site in order to be analysed. Analysis of a sludge test material has been performed to create a suitable benchmark material for the rheological measurements with the prototype. Development of the device is being undertaken with commercial off the shelf (COTS) components and modern rapid prototyping techniques. Using these techniques, an initial prototype for measuring shear parameters of sludge has been developed, using a micro-controller for remote control and data gathering. The device is also compact enough to fit through a 75 mm opening, maximising deployment capabilities.
RESUMO
The development of a bio-hybrid tactile sensor array that incorporates a skin analogue comprised of alginate encapsulated fibroblasts is described. The electrical properties are modulated by mechanical stress induced during contact, and changes are detected by a ten-channel dual-electrode impedance sensing array. By continuously monitoring the impedance of the sensor array at a fixed frequency, whilst normal and tangential loads are applied to the skin surface, transient mechanotransduction has been observed. The results demonstrate the effectiveness and feasibility of the preliminary prototype bio-hybrid tactile sensor.
Assuntos
Técnicas Biossensoriais , Pele Artificial , Tato/fisiologia , Impedância Elétrica , Eletrodos , Humanos , Mecanotransdução Celular/fisiologiaRESUMO
This work studies the potential of using short life fission product (AFp) radioisotopes e.g. 82Br, 86Rb, (90Sr) - 90mY, (99Mo) - 99mTc, 103Ru - 103mRh, 111Ag, 127Sb - 127(m)Te, 126I, 131I, 133Xe, 136Cs, 141Ce, 143Ce, 143Pr, 147Nd - 147Pm, 149Pm, 153Sm, 156Eu, 159Gd and 161Tb, extracted from a molten salt reactor and their separation using specific thermodynamic and radiochemical conditions. Their utilisation for coupled radiodiagnostics and radiotherapy is a key consideration. A molten salt reactor produces fission products during operation. These radioisotopes can be separated at line from the liquid fuel by evaporation/distillation, chemical reduction (using H2 doped gas), electro-deposition and/or chemical oxidation (using Cl2 doped gas). They can be refined and chemically treated for radiopharmaceutical use for imaging and radiodiagnostics utilising γ radioscopy or positron emission tomography, and potentially in radiotherapy to target specific cancers or viral diseases using ß- emitters. Some of the AFp isotopes are currently used for radiodiagnostics because they emit γ rays of energy 50-200 keV. However, some may also be used in parallel for radiotherapy utilising their ß- (EMean ≈ 100 keV) emission whose mean free pathway of c.a. 100 nm in biological tissue is much smaller than their penetration depth. Focus is given to 86Rb, 90Y, 99mTc, 131I and 133Xe as well as on the ALn isotopes (141Ce, 143Ce - 143Pr, 147Nd - 147Pm, 149Pm and 153Sm) because of their strong potential for complexation with bio-ligands (e.g. DOTA) or for their ability to form micro-nano-spheres, and because of their potential for dual radiodiagnostics and radiotherapy. It is shown that these radio-lanthanides could also replace 177Lu for the treatment of specific cancers.
Assuntos
Neoplasias , Compostos Radiofarmacêuticos , Humanos , Radioisótopos , Tomografia por Emissão de PósitronsRESUMO
Microneedle arrays are minimally invasive devices that have been extensively investigated for the transdermal/intradermal delivery of drugs/bioactives. Here, we demonstrate the release of bioactive molecules (estradiol, melatonin and meropenem) from poly(2-hydroxyethyl methacrylate), pHEMA, hydrogel-based microneedle patches in vitro. The pHEMA hydrogel microneedles had mechanical properties that were sufficiently robust to penetrate soft tissues (exemplified here by phantom tissues). The bioactive release from the pHEMA hydrogel-based microneedles was fitted to various models (e.g., zero order, first order, second order). Such pHEMA microneedles have potential application in the transdermal delivery of bioactives (exemplified here by estradiol, melatonin and meropenem) for the treatment of various conditions.
RESUMO
The release of metformin, a drug used in the treatment of cancer and diabetes, from poly(2-hydroxyethyl methacrylate), pHEMA, hydrogel-based microneedle patches is demonstrated in vitro. Tuning the composition of the pHEMA hydrogels enables preparation of robust microneedle patches with mechanical properties such that they would penetrate skin (insertion force of a single microneedle to be ≈40 N). Swelling experiments conducted at 20, 35, and 60 °C show temperature-dependent degrees of swelling and diffusion kinetics. Drug release from the pHEMA hydrogel-based microneedles is fitted to various models (e.g., zero order, first order, second order). Such pHEMA microneedles have potential application for transdermal delivery of metformin for the treatment of aging, cancer, diabetes, etc.
RESUMO
The measurement of the physical properties of surfaces on the nanoscale is a long-standing problem, and the atomic force microscope (AFM) has enabled the investigation of surface energies and mechanical properties over a range of length scales. The ability to measure these properties for softer materials presents a challenge when interpreting data obtained from such measurements, in particular because of the dynamics of the compliant AFM microcantilever. This work attempts to better understand the interaction between an AFM tip and samples of varying elastic modulus, in the presence of attractive van der Waals forces. A theoretical model is presented in which the dynamics of the approach of an atomic force microscope cantilever tip toward a surface, prior to and during the van der Waals-induced jump-to phenomenon, are included. The cantilever mechanics incorporates the motion of the air through which the cantilever moves, the acceleration, inertia, and torque of the cantilever, and the squeezing of the fluid between the cantilever tip and the surface, leading to elastohydrodynamic lubrication and deformation of the substrate. Simulations of the cantilever approach are compared to measurements performed using an atomic force microscope, and the effect of cantilever drive velocity is investigated. Cantilevers presenting (1) spherical colloid probe tips and (2) pyramidal tips are employed, and substrates exhibiting Young's moduli of 3 MPa, 500 MPa, and 75 GPa are measured. The analysis presented could be extended to enhance understanding of dynamic phenomena in micro/nanoelectromechanical systems such as resonators and microrheometers, particularly those which contain soft materials and also where surface interactions are important.
RESUMO
In situ repair and maintenance of high-value industrial equipment is critical if they are to maintain the ability to continue vital operations. Conventional single-arm continuum robots have been proven numerous times to be successful tools for use in repair operations. However, often more than one arm is needed to ensure successful operation within several scenarios; thus, the collaborative operation of multiple arms is required. Here, we present the design and operating principles of a dual-arm continuum robot system designed to perform critical tasks within industrial settings. Here, presented are the design principle of the robotic system, the optimization-based inverse kinematic calculation of the 6-DoF continuum arms, and the collaborative operation strategy. The collaborative principle and algorithms used have been evaluated by a set of experiments to demonstrate the ability of the system to perform in situ machining operations. With the developed prototype and controller, the average error between planned and real toolpaths can be within 2.5 mm.
RESUMO
The adhesive characteristics of thin films (0.2-2 µm) of linear poly(dimethylsiloxane) (PDMS) liquids with a wide range of molecular weights have been measured using an atomic force microscope with a colloid probe (diameters 5 and 12 µm) for different separation velocities. The data were consistent with a residual film in the contact region having a thickness of â¼6 nm following an extended dwell time before separation of the probe. It was possible to estimate the maximum adhesive force as a function of the capillary number, Ca, by applying existing theoretical models based on capillary interactions and viscous flow except at large values of Ca in the case of viscoelastic fluids, for which it was necessary to develop a nonlinear viscoelastic model. The compliance of the atomic force microscope colloid beam was an important factor in governing the retraction velocity of the probe and therefore the value of the adhesive force, but the inertia of the beam and viscoelastic stress overshoot effects were not significant in the range of separation velocities investigated.
Assuntos
Adesivos/química , Elasticidade , Microscopia de Força Atômica , Silicones/química , Coloides , Dimetilpolisiloxanos/química , Luz , Modelos Teóricos , Espalhamento de Radiação , Solventes/química , ViscosidadeRESUMO
Several millions of kilometres of pipes and cables are buried beneath our streets in the UK. As they are not visible and easily accessible, the monitoring of their integrity as well as the quality of their contents is a challenge. Any information of these properties aids the utility owners in their planning and management of their maintenance regime. Traditionally, expensive and very localised sensors are used to provide irregular measurements of these properties. In order to have a complete picture of the utility network, cheaper sensors need to be investigated which would allow large numbers of small sensors to be incorporated into (or near to) the pipe leading to so-called smart pipes. This paper focuses on a novel trial where a short section of a prototype smart pipe was buried using mainly off-the-shelf sensors and communication elements. The challenges of such a burial are presented together with the limitations of the sensor system. Results from the sensors were obtained during and after burial indicating that off-the-shelf sensors can be used in a smart pipes system although further refinements are necessary in order to miniaturise these sensors. The key challenges identified were the powering of these sensors and the communication of the data to the operator using a range of different methods.
RESUMO
Targeting biomedical applications, Triply Periodic Minimal Surface (TPMS) gyroid sheet-based structures were successfully manufactured for the first time by Electron Beam Melting in two different production Themes, i.e., inputting a zero (Wafer Theme) and a 200 µm (Melt Theme) wall thickness. Initial assumption was that in both cases, EBM manufacturing should yield the structures with similar mechanical properties as in a Wafer-mode, as wall thickness is determined by the minimal beam spot size of ca 200 µm. Their surface morphology, geometry, and mechanical properties were investigated by means of electron microscopy (SEM), X-ray Computed Tomography (XCT), and uniaxial tests (both compression and tension). Application of different manufacturing Themes resulted in specimens with different wall thicknesses while quasi-elastic gradients for different Themes was found to be of 1.5 GPa, similar to the elastic modulus of human cortical bone tissue. The specific energy absorption at 50% strain was also similar for the two types of structures. Finite element simulations were also conducted to qualitatively analyze the deformation process and the stress distribution under mechanical load. Simulations demonstrated that in the elastic regime wall, regions oriented parallel to the load are primarily affected by deformation. We could conclude that gyroids manufactured in Wafer and Melt Themes are equally effective in mimicking mechanical properties of the bones.
RESUMO
Efforts to develop tissue-engineered skin for regenerative medicine have explored natural, synthetic, and hybrid hydrogels. The creation of a bilayer material, with the stratification exhibited by native skin, is a complex problem. The mechanically robust, waterproof epidermis presents the stratum corneum at the tissue/air interface, which confers many of these protective properties. In this work, we explore the effect of high temperatures on alginate hydrogels, which are widely employed for tissue engineering due to their excellent mechanical properties and cellular compatibility. In particular, we investigate the rapid dehydration of the hydrogel surface which occurs following local exposure to heated surfaces with temperatures in the range 100-200 °C. We report the creation of a mechanically strengthened hydrogel surface, with improved puncture resistance and increased coefficient of friction, compared to an unheated surface. The use of a mechanical restraint during heating promoted differences in the rate of mass loss; the rate of temperature increase within the hydrogel, in the presence and absence of restraint, is simulated and discussed. It is hoped that the results will be of use in the development of processes suitable for preparing skin-like analogues; application areas could include wound healing and skin restoration.
RESUMO
Metallisation is a vital process for micro- and nanofabrication, allowing the controlled preparation of material surfaces with thin films of a variety of metals. The films are often subjected to further processing, including etching, patterning, chemical modification, and additional lamination. The extensive applications of metallised substrates include chemical sensors and nanoelectronics. Here, we report an experimental study of the metallisation of silicon cantilevers with nano-films of chromium and titanium. Analysis of the stress distribution throughout the cantilever showed that metallisation causes a constant stress along the length of the beam, which can be calculated from interferometric quantification of the beam curvature. The structure of the metal/silicon interface was imaged using electron microscopy in an attempt to ascertain the physical origin of the stress. A theoretical model is constructed for the stressed beam system, and it is shown that there is no single parameter that can describe the change in stress. The resultant structure after deposition varies significantly for each metal, which gives rise to a variety of stress directions and magnitudes.
RESUMO
Alginate hydrogels are commonly used in biomedical applications such as scaffolds for tissue engineering, drug delivery, and as a medium for cell immobilisation. Multivalent cations are often employed to create physical crosslinks between carboxyl and hydroxyl moieties on neighbouring polysaccharide chains, creating hydrogels with a range of mechanical properties. This work describes the manufacture and characterisation of sodium alginate hydrogels using the divalent cations Mg(2+), Ca(2+) and Sr(2+) to promote gelation via non-covalent crosslinks. Gelation time and Young׳s modulus are characterised as a function of cation and alginate concentrations. The implications of this work towards the use of environmental elasticity to control stem cell differentiation are discussed.