Highly Durable and Active PtFe Nanocatalyst for Electrochemical Oxygen Reduction Reaction.

Demand on the practical synthetic approach to the high performance electrocatalyst is rapidly increasing for fuel cell commercialization. Here we present a synthesis of highly durable and active intermetallic ordered face-centered tetragonal (fct)-PtFe nanoparticles (NPs) coated with a "dual purpose" N-doped carbon shell. Ordered fct-PtFe NPs with the size of only a few nanometers are obtained by thermal annealing of polydopamine-coated PtFe NPs, and the N-doped carbon shell that is in situ formed from dopamine coating could effectively prevent the coalescence of NPs. This carbon shell also protects the NPs from detachment and agglomeration as well as dissolution throughout the harsh fuel cell operating conditions. By controlling the thickness of the shell below 1 nm, we achieved excellent protection of the NPs as well as high catalytic activity, as the thin carbon shell is highly permeable for the reactant molecules. Our ordered fct-PtFe/C nanocatalyst coated with an N-doped carbon shell shows 11.4 times-higher mass activity and 10.5 times-higher specific activity than commercial Pt/C catalyst. Moreover, we accomplished the long-term stability in membrane electrode assembly (MEA) for 100 h without significant activity loss. From in situ XANES, EDS, and first-principles calculations, we confirmed that an ordered fct-PtFe structure is critical for the long-term stability of our nanocatalyst. This strategy utilizing an N-doped carbon shell for obtaining a small ordered-fct PtFe nanocatalyst as well as protecting the catalyst during fuel cell cycling is expected to open a new simple and effective route for the commercialization of fuel cells.

Tuning the oxygen reduction activity of the Pt-Ni nanoparticles upon specific anion adsorption by varying heat treatment atmospheres.

Heat treatment of Pt based nanoparticles under various conditions is one of the conventional ways to modify the electrocatalytic properties for enhancement of the oxygen reduction reaction (ORR). However, the effect of the heat treatment atmosphere on the ORR activity especially upon specific anion adsorption still remains unclear. This paper investigates the Pt-Ni bimetallic nanoparticles (Pt2Ni1), under various heat treatment atmospheres, as enhanced cathodic electrocatalysts for the high temperature-proton exchange membrane fuel cell (HT-PEMFC) using a phosphoric acid doped polybenzimidazole (p-PBI) membrane. The X-ray spectroscopic measurement showed the variations of the electronic structures of Pt-Ni nanoparticles under the heat treatment condition. In the half-cell measurement, the argon treated electrocatalyst demonstrated the highest catalytic activity owing to the appropriate electronic interaction between Pt and Ni. The single cell test with a p-PBI membrane, at 160 °C, also confirmed the excellent oxygen reduction reactivity and durability of the argon-treated Pt-Ni nanoparticles. This result suggested that the alteration of the electronic structure by a proper heat treatment atmosphere upon specific anion adsorption decisively influenced the ORR activity both at half-cell and single-cell scales.

Correlation between platinum nanoparticle surface rearrangement induced by heat treatment and activity for an oxygen reduction reaction.

Heat treatment of nanoparticles could induce the surface rearrangement for more stable facet exposure induced by thermodynamics. By changing the heat treatment environment, we confirmed the correlation between the oxygen reduction activity and the effect of surface oxide and the degree of surface rearrangement of Pt nanoparticles. Native surface oxide was not a critical factor for oxygen reduction activity. However, the degree of surface rearrangement could affect the activity, which was confirmed by the surface sensitive techniques such as CO(ad) oxidation and potential of zero total charge. Analysis indicated that the driving force for nanoparticle surface rearrangement was affected by the heat treatment environment such as gas, in our case.

Chemical tuning of electrochemical properties of Pt-skin surfaces for highly active oxygen reduction reactions.

Pt-skin surfaces were successfully fabricated by the chemical deposition of additional Pt on corrugated Pt-Ni nanoparticles with Pt-skeleton surfaces. Compared to the Pt-skin formed by heat annealing, the chemically-tuned Pt-skin had a higher Pt coordination number and surface crystallinity, which resulted in superior ORR activity and durability.

Usefulness of three-channel multiplex real-time PCR and melting curve analysis for simultaneous detection and identification of the Mycobacterium tuberculosis complex and nontuberculous mycobacteria.

We attempted to determine the benefits of three-channel multiplex real-time PCR and melting curve analysis not only in detecting and distinguishing between nontuberculous mycobacteria (NTM) and the Mycobacterium tuberculosis complex but also in identifying NTM to the species level.

Anomalous in situ Activation of Carbon-Supported Ni2P Nanoparticles for Oxygen Evolving Electrocatalysis in Alkaline Media.

Electrochemical water splitting is one of the most promising systems by which to store energy produced from sustainable sources, such as solar and wind energy. Designing robust and stable electrocatalysts is urgently needed because of the relatively sluggish kinetics of the anodic reaction, i.e. the oxygen evolution reaction (OER). In this study, we investigate the anomalous in situ activation behaviour of carbon-supported Ni2P nanoparticles (Ni2P/C) during OER catalysis in alkaline media. The activated Ni2P/C shows an exceptionally high activity and stability under OER conditions in which the overpotential needed to achieve 10 mA cm-2 was reduced from approximately 350 mV to approximately 300 mV after 8,000 cyclic voltammetric scans. In situ and ex situ characterizations indicate that the activity enhancement of Ni2P catalysts is due to a favourable phase transformation of the Ni centre to ß-NiOOH, including increases in the active area induced by structural deformation under the OER conditions. These findings provide new insights towards designing transition metal/phosphide-based materials for an efficient water splitting catalyst.

Third-body effects of native surfactants on Pt nanoparticle electrocatalysts in proton exchange fuel cells.

The residual surfactant organic molecules on electrocatalysts are expected to enhance the tolerance to specific anion adsorption, whereas the surfactants have been generally regarded as contaminants that block active surfaces. In this study, the Pt nanoparticles with adsorbed surfactants were prepared, and their electrochemical characteristics at various phosphoric acid concentrations were studied by the half-cell test. The third-body effect was experimentally confirmed by the single-cell test with a phosphoric acid-doped polybenzimidazole membrane.

Green synthesis of carbon-supported nanoparticle catalysts by physical vapor deposition on soluble powder substrates.

Metal and metal oxide nanoparticles (NPs) supported on high surface area carbon (NP/Cs) were prepared by the physical vapor deposition of bulk materials on an α-D-glucose (Glu) substrate, followed by the deposition of the NPs on carbon supports. Using Glu as a carrier for the transport of NPs from the bulk materials to the carbon support surfaces, ultrafine NPs were obtained, exhibiting a stabilizing effect through OH moieties on the Glu surfaces. This stabilizing effect was strong enough to stabilize the NPs, but weak enough to not significantly block the metal surfaces. As only the target materials and Glu are required in our procedure, it can be considered environmentally friendly, with the NPs being devoid of hazardous chemicals. Furthermore, the resulting NP/Cs exhibited an improvement in activity for various electrochemical reactions, mainly attributed to their high surface area.

Inhibition of CO poisoning on Pt catalyst coupled with the reduction of toxic hexavalent chromium in a dual-functional fuel cell.

We propose a method to enhance the fuel cell efficiency with the simultaneous removal of toxic heavy metal ions. Carbon monoxide (CO), an intermediate of methanol oxidation that is primarily responsible for Pt catalyst deactivation, can be used as an in-situ reducing agent for hexavalent chromium (Cr (VI)) with reactivating the CO-poisoned Pt catalyst. Using electro-oxidation measurements, the oxidation of adsorbed CO molecules coupled with the concurrent conversion of Cr (VI) to Cr (III) was confirmed. This concept was also successfully applied to a methanol fuel cell to enhance its performance efficiency and to remove toxic Cr (VI) at the same time.

Edge-exposed MoS2 nano-assembled structures as efficient electrocatalysts for hydrogen evolution reaction.

Edge-exposed MoS2 nano-assembled structures are designed for high hydrogen evolution reaction activity and long term stability. The number of sulfur edge sites of nano-assembled spheres and sheets is confirmed by Raman spectroscopy and EXAFS analysis. By controlling the MoS2 morphology with the formation of nano-assembled spheres with the assembly of small-size fragments of MoS2, the resulting assembled spheres have high electrocatalytic HER activity and high thermodynamic stability.

Tailoring the Electronic Structure of Nanoelectrocatalysts Induced by a Surface-Capping Organic Molecule for the Oxygen Reduction Reaction.

Capping organic molecules, including oleylamine, strongly adsorbed onto Pt nanoparticles during preparation steps are considered undesirable species for the oxygen reduction reaction due to decreasing electrochemical active sites. However, we found that a small amount of oleylamine modified platinum nanoparticles showed significant enhancement of the electrochemical activity of the oxygen reduction reaction, even with the loss of the electrochemically active surface area. The enhancement was correlated with the downshift of the frontier d-band structure of platinum and the retardation of competitively adsorbed species. These results suggest that a capping organic molecule modified electrode can be a strategy to design an advanced electrocatalyst by modification of electronic structures.