RESUMO
We propose a simple two-channel mode-group-division-multiplexing (MGDM) system operating in the 0.8 µm region over the standard single-mode fiber (SSMF). For the cost-effectiveness, we implement its receiver by using only two photodetectors (PDs) [instead of three PDs required for the detection of the LP01,LP11a, and LP11b modes]. We then detect the signal carried by the LP01 mode by using a PD and a mode filter. On the other hand, the other signal carried by the LP11 mode group is detected by using another PD and a multiple-input single-output equalizer (i.e., by subtracting the signal carried by the LP01 mode from the multiplexed signal). For a demonstration, we transmit 2×28Gb/s MGDM on-off keying signal operating at 852.6 nm over 2.2 km of the SSMF by using the proposed technique. The results show that we can achieve the bit-error rate of <3.8×10-3 for both the LP01 and LP11 modes.
RESUMO
The multipath interference (MPI) noise is one of the most important limiting factors on the performance of the mobile fronthaul network (MFN) based on the radio-over-fiber (RoF) technology. Recently, it has been proposed to suppress this MPI noise by using the Gaussian phase dither. However, it broadens the optical spectrum significantly and, as a result, increases its vulnerability to the chromatic dispersion. To overcome this problem, we propose to suppress the MPI noise by using the RF-chirp dither instead of the Gaussian dither. The results show that, due to the narrow optical spectrum achieved by the RF-chirp dither, we can increase the transmission distance of the RoF-based MFN operating in the 1.5-µm region by three times.
RESUMO
We propose and demonstrate a simple composite second-order (CSO) cancellation technique based on the digital signal processing (DSP) for the radio-over-fiber (RoF) transmission system implemented by using directly modulated lasers (DMLs). When the RoF transmission system is implemented by using DMLs, its performance could be limited by the CSO distortions caused by the interplay between the DML's chirp and fiber's chromatic dispersion. We present the theoretical analysis of these nonlinear distortions and show that they can be suppressed at the receiver by using a simple DSP. To verify the effectiveness of the proposed technique, we demonstrate the transmission of twenty-four 100-MHz filtered orthogonal frequency-division multiplexing (f-OFDM) signals in 64 quadrature amplitude modulation (QAM) format over 20 km of the standard single-mode fiber (SSMF). The results show that, by using the proposed technique, we can suppress the CSO distortion components by >10 dB and achieve the error-vector magnitude performance better than 6% even after the 20-km long SSMF transmission.
RESUMO
We propose and demonstrate a simple detuning method for the low-chirp operation of a polymer-based tunable external-cavity laser (ECL). To ensure the low-chirp operation of this directly-modulated ECL, we first obtain the optimum values of the heater current applied to the polymer Bragg grating reflector (PBR) and the operating temperature of this ECL. For this purpose, we sweep the current applied to the phase control heater until the peak output power measured from the high-reflection (HR) coated facet reaches the minimum value. We then operate this ECL with minimum chirp by tuning the lasing mode to the longer wavelength limit of the stable operation region. This is because the detuned loading effect is maximized at this limit as the in-phase condition between the lights reflected from the PBR and anti-reflection (AR) coated facet of the gain medium is satisfied. Thus, by using this method together with conventional wavelength-locking algorithm, we can operate this ECL with minimum chirp at any wavelength.
RESUMO
We present and demonstrate a simple and cost-effective technique for improving the modulation bandwidth of electroabsorption-modulated laser (EML). This technique utilizes the RF resonance caused by the EML chip (i.e., junction capacitance) and bonding wire (i.e, wire inductance). We analyze the effects of the lengths of the bonding wires on the frequency responses of EML by using an equivalent circuit model. To verify this analysis, we package a lumped EML chip on the sub-mount and measure its frequency responses. The results show that, by using the proposed technique, we can increase the modulation bandwidth of EML from ~16 GHz to ~28 GHz.
Assuntos
Lasers , Absorção , Campos Eletromagnéticos , Desenho de Equipamento , Análise de Falha de EquipamentoRESUMO
We demonstrate a directly-modulated 10-Gb/s tunable external cavity laser (ECL) fabricated by using a polymer Bragg reflector and a high-speed superluminescent diode (SLD). The tuning range and output power of this ECL are measured to be >11 nm and 2.6 mW (@ 100 mA), respectively. We directly modulate this laser at 10 Gb/s and transmit the modulated signal over 20 km of standard single-mode fiber. The power penalty is measured to be <2.8 dB at the bit-error rate (BER) of 10(-10).
Assuntos
Lasers , Iluminação/instrumentação , Refratometria/instrumentação , SemicondutoresRESUMO
We demonstrate a technique for performance monitoring of quadrature phase-shift keying data channels by simultaneously identifying optical signal-to-noise ratio (OSNR), chromatic dispersion (CD), and polarization-mode dispersion (PMD) using neural networks trained with parameters derived from asynchronous constellation diagrams. A correlation coefficient of 0.987 is reported for a set of testing data from a 40 Gbps return-to-zero, quadrature phase-shift keying (RZ-QPSK) system. The root-mean-square (RMS) errors are 0.77 dB for OSNR, 18.71 ps/nm for CD, and 1.17 ps for DGD.