Recent Advances in the Separation of Rare Earth Elements Using Mesoporous Hybrid Materials.

Over the past decades, the need for rare earth elements (REEs) has increased substantially, mostly because these elements are used as valuable additives in advanced technologies. However, the difference in ionic radius between neighboring REEs is small, which renders an efficient sized-based separation extremely challenging. Among different types of extraction methods, solid-phase extraction (SPE) is a promising candidate, featuring high enrichment factor, rapid adsorption kinetics, reduced solvent consumption and minimized waste generation. The great challenge remains yet to develop highly efficient and selective adsorbents for this process. In this regard, ordered mesoporous materials (OMMs) possess high specific surface area, tunable pore size, large pore volume, as well as stable and interconnected frameworks with active pore surfaces for functionalization. Such features meet the requirements for enhanced adsorbents, not only providing huge reactional interface and large surface capable of accommodating guest species, but also enabling the possibility of ion-specific binding for enrichment and separation purposes. This short personal account summarizes some of the recent advances in the use of porous hybrid materials as selective sorbents for REE separation and purification, with particular attention devoted to ordered mesoporous silica and carbon-based sorbents.

Carbamoylmethylphosphine Oxide-Functionalized MIL-101(Cr) as Highly Selective Uranium Adsorbent.

The carbamoylmethylphosphine oxide (CMPO) functionalized MIL-101(Cr) was investigated as a potential uranium scavenger. This metal-organic framework-based adsorbent shows very high selectivity toward uranium, as well as thorium, in competition with various rare earth metals. Furthermore, it showed rapid adsorption kinetics, in both batch conditions and a dynamic (column) setup. The adsorbent is fully regenerable, using oxalate solution. Fast elution kinetics in the column setup were observed during the regeneration. In addition, reusability studies were performed under dynamic conditions. Five consecutive adsorption/desorption cycles were carried out, showing a consistent 100% recovery, at pH 4, using 0.1 M oxalate solution as an effective stripping agent. Additionally, the successive use over various adsorption/desorption cycles with constant performance proves the high stability of this adsorbent in an acidic, aqueous environment.

In Vitro Dissolution, Cellular Membrane Permeability, and Anti-Inflammatory Response of Resveratrol-Encapsulated Mesoporous Silica Nanoparticles.

Sizing drugs down to the submicron and nanometer scale using nanoparticles has been extensively used in pharmaceutical industries to overcome the poor aqueous solubility of potential therapeutic agents. Here, we report the encapsulation and release of resveratrol, a promising anti-inflammatory and anticancer nutraceutical, from the mesopores of MCM-48-type silica nanospheres of various particle sizes, i.e., 90, 150, and 300 nm. Furthermore, the influence of the carrier pore size on drug solubility was also evaluated (3.5 vs 7 nm). From our results, it is observed that the saturated solubility could depend not only on the pore size but also on the particle size of the nanocarriers. Moreover, with our resveratrol-mesoporous silica nanoparticles formulation, we have observed that the permeability of resveratrol encapsulated in MCM-48 nanoparticles (90 nm) can be enhanced compared to a resveratrol suspension when tested through the human colon carcinoma cell monolayer (Caco-2). Using an in vitro NF-κB assay, we showed that resveratrol encapsulation did not alter its bioactivity and, at lower concentration, i.e., 5 µg mL-1, resveratrol encapsulation provided higher anti-inflammatory activity compared to both resveratrol suspension and solution. All combined, the reported results clearly highlight the potential of small size mesoporous silica nanoparticles as next generation nanocarriers for hydrophobic drugs and nutraceuticals.

Low-Temperature controlled synthesis of nanocast mixed metal oxide spinels for enhanced OER activity.

The controlled cation substitution is an effective strategy for optimizing the density of states and enhancing the electrocatalytic activity of transition metal oxide catalysts for water splitting. However, achieving tailored mesoporosity while maintaining elemental homogeneity and phase purity remains a significant challenge, especially when aiming for complex multi-metal oxides. In this study, we utilized a one-step impregnation nanocasting method for synthesizing mesoporous Mn-, Fe-, and Ni-substituted cobalt spinel oxide (Mn0.1Fe0.1Ni0.3Co2.5O4, MFNCO) and demonstrate the benefits of low-temperature calcination within a semi-sealed container at 150-200 °C. The comprehensive discussion of calcination temperature effects on porosity, particle size, surface chemistry and catalytic performance for the alkaline oxygen evolution reaction (OER) highlights the importance of humidity, which was modulated by a pre-drying step. The catalyst calcined at 170 °C exhibited the lowest overpotential (335 mV at 10 mA cm-2), highest current density (433 mA cm-2 at 1.7 V vs. RHE, reversible hydrogen electrode) and further displayed excellent stability over 22 h (at 10 mA cm-2). Furthermore, we successfully adapted this method to utilize cheap, commercially available silica gel as a hard template, yielding comparable OER performance. Our results represent a significant progress in the cost-efficient large-scale preparation of complex multi-metal oxides for catalytic applications.

A perspective on developing solid-phase extraction technologies for industrial-scale critical materials recovery.

Critical materials (CMs) are a group of elements that have been determined to be important for the modern economy, but which may face current or potential supply limitations. Some examples of metals that have received the CM designation include the rare earth elements, indium, gallium, and lithium. The last decade has seen a major push for the development of new and improved technologies for the recovery and purification of CMs from various traditional and non-traditional resources in an effort to diversify supply. Solid-phase extraction (SPE) is one broad category of these experimental extraction technologies. SPE involves the application of a solid material to preferentially retain in the solid phase one or more specific components of an aqueous solution, leaving the other components behind in the aqueous phase. A wide range of different sorbents has been used for SPE, and many offer significant potential advantages, including low cost, low environmental impact, and high customizability. Hierarchically porous silica monoliths are one example of a cutting-edge sorbent that provides a durable, high surface area foundation that can be functionalized with a variety of targeted ligands for the selective extraction of specific CMs. Despite impressive recent advances in SPE, there remain areas for improvement that are common across the discipline. To demonstrate the practical viability of these innovative CM recovery systems, future SPE studies would benefit from devoting additional focus to the scalability of their material, as well as from focusing on real-world feedstocks and conducting techno-economic analyses and environmental impact studies.

Understanding Selectivity of Mesoporous Silica-Grafted Diglycolamide-Type Ligands in the Solid-Phase Extraction of Rare Earths.

Rare earth elements (REEs) and their compounds are essential for rapidly developing modern technologies. These materials are especially critical in the area of green/sustainable energy; however, only very high-purity fractions are appropriate for these applications. Yet, achieving efficient REE separation and purification in an economically and environmentally effective way remains a challenge. Moreover, current extraction technologies often generate large amounts of undesirable wastes. In that perspective, the development of selective, reusable, and extremely efficient sorbents is needed. Among numerous ligands used in the liquid-liquid extraction (LLE) process, the diglycolamide-based (DGA) ligands play a leading role. Although these ligands display notable extraction performance in the liquid phase, their extractive chemistry is not widely studied when such ligands are tethered to a solid support. A detailed understanding of the relationship between chemical structure and function (i.e., extraction selectivity) at the molecular level is still missing although it is a key factor for the development of advanced sorbents with tailored selectivity. Herein, a series of functionalized mesoporous silica (KIT-6) solid phases were investigated as sorbents for the selective extraction of REEs. To better understand the extraction behavior of these sorbents, different spectroscopic techniques (solid-state NMR, X-ray photoelectron spectroscopy, XPS, and Fourier transform infrared spectroscopy, FT-IR) were implemented. The obtained spectroscopic results provide useful insights into the chemical environment and reactivity of the chelating ligand anchored on the KIT-6 support. Furthermore, it can be suggested that depending on the extracted metal and/or structure of the ligand and its attachment to KIT-6, different functional groups (i.e., C═O, N-H, or silanols) act as the main adsorption centers and preferentially capture targeted elements, which in turn may be associated with the different selectivity of the synthesized sorbents. Thus, by determining how metals interact with different supports, we aim to better understand the solid-phase extraction process of hybrid (organo)silica sorbents and design better extraction materials.

Gastro-protective protein-silica nanoparticles formulation for oral drug delivery: In vitro release, cytotoxicity and mitochondrial activity.

Our contribution aims to provide an efficient solution to one of the major challenges of oral delivery of gastro-sensitive drugs, namely preventing their premature release and degradation in the gastric fluid in order to maximize the absorption in the small intestine. Our results show that a pH-responsive protein, i.e., succinylated ß-lactoglobulin (BL), together with the key attributes of mesoporous silica nanoparticles (MSNs), can synergetically reduce the release of the gastro-sensitive drug, omeprazole (OMP), in acidic pH and enhance the dissolution in intestinal pH conditions. Two families of MSNs were synthesized, MCM-48-based and dendritic-type MSNs, and both materials were additionally functionalized with trimethylsilyl groups to produce a hydrophobic surface that can further modulate the interaction of the MSNs with the succinylated protein in the nanoformulation. The methyl-functionalization of the MSNs also impacted on the physical state of the confined OMP and consequently on its release in near neutral pH. Our cytotoxicity screening revealed no particular mitochondrial dysfunction originating from the MSNs. Moreover, upon progressive release of the drug confined into dendritic-type MSNs, the cytotoxicity against tumorigenic and non-tumorigenic cells (Caco-2 and HCEC) was significantly lower in comparison to the drug pre-dissolved in DMSO.

Size-Selective Separation of Rare Earth Elements Using Functionalized Mesoporous Silica Materials.

The separation and preconcentration of rare earth elements (REEs) from mineral concentrates in an economically and environmentally sustainable manner are difficult tasks due to their similar physicochemical properties. Herein, a series of tetradentate phenylenedioxy diamide (PDDA) ligands were synthesized and grafted on large-pore three-dimensional KIT-6 mesoporous silica. In solid-phase extraction, the hybrid sorbents enable a size-selective separation of REEs on the basis of the bite angles of the ligands. In particular, smaller REE3+ ions are preferentially extracted by KIT-6-1,2-PDDA, whereas light REEs with larger ionic radius are favored by KIT-6-1,3-PDDA. The exposure of bauxite residue digestion solution containing REEs as well as a number of types of competitive ions (including Th and U) to the sorbents results in selective recovery of target REEs. The possibility of regenerating the mesoporous sorbents through a simple loading-stripping-regeneration process is demonstrated over up to five cycles with no significant loss in REE extraction capacity, suggesting adequate chemical and structural stability of the new sorbent materials.

Synthesis and radiometric evaluation of diglycolamide functionalized mesoporous silica for the chromatographic separation of actinides Th, Pa and U.

The separation of Th, Pa, and U is of high importance in many applications including nuclear power, nuclear waste, environmental and geochemistry, nuclear forensics and nuclear medicine. Diglycolamide (DGA)-based resins have shown the ability to separate many elements, however, these resins consist of non-covalent impregnation of the DGA molecules on the resin backbone resulting in co-elution of the extraction molecule during separation cycles, therefore limiting their long-term and repeated use. Covalently binding the DGA molecules onto silica is one way to overcome this issue. Herein, measured equilibrium distribution coefficients of normal extraction chromatographic DGA resin and a covalently bound form (KIT-6-N-DGA sorbent) are reported. Several differences are observed between the two systems, the most significant being observed for uranium, which demonstrated significantly lower sorption behavior on KIT-6-N-DGA. These results indicate that U can effectively be separated from Th and Pa using KIT-6-N-DGA, a task that could not be completed with the use of normal DGA alone.

Evaluation of mesoporous silica nanoparticles for oral drug delivery - current status and perspective of MSNs drug carriers.

The oral pathway is considered as the most common method for drug administration, although many drugs, especially the highly pH- and/or enzymatic biodegradable peptide drugs, are very difficult to formulate and achieve a good intestinal absorption. Efficient systematic absorption of an active substance, delivered via oral ingestion, is only achievable if the drug (1) is substantially present as a solution in the gastrointestinal tract, (2) is able to penetrate through the intestinal mucus, (3) overcomes the different gastrointestinal barriers, and (4) provides an effective therapeutic dose. Therefore, optimization of oral bioavailability of poorly-soluble drugs still remains a significant challenge for the pharmaceutical industry. Even though numerous conventional drug carriers have successfully solved some of the issues related to oral delivery of poorly-soluble drugs, only few of them met commercialization requirements. These drawbacks have led the scientific world to reconsider its approaches toward targeted drug delivery systems and researchers started looking for alternative vectorized carriers. In this area, nanoparticle-based materials have several significant advantages over free and non-formulated drugs. For example, nanosized porous silica carriers allow for more sustained and controlled drug release or improved oral bioavailability. Thus, in the present review, we will highlight the most important features of nanostructured silica drug carriers, such as particle size, particle shape, surface roughness or surface functionalization, and underline the key advantages of these nanosupports. In particular, this article will discuss recent progress and challenges in the area of mesoporous silica nanocarriers used for oral drug delivery. Additional emphasis will be set on the biological and chemical features of the gastrointestinal tract as well as currently tested nanoformulations and strategies to avoid drug degradation in the gastrointestinal environment.

Functionalization of Mesoporous Carbon Materials for Selective Separation of Lanthanides under Acidic Conditions.

New functional mesoporous carbon sorbents were successfully synthesized to overcome some issues of solid-liquid extraction (e.g., selectivity, extraction capacity, and reusability under acidic conditions) in production of pure lanthanides (Ln). Wet-oxidation technique was performed to increase the surface reactivity of pristine ordered mesoporous carbon (OMC), and, in a second step, a surface modification using diglycolamide-based (DGA-based) selective ligands toward Ln was performed. Two types of ligands were tested: the first contains a long spacer (e.g., between carbon support and chelating function), and the second has a shorter one. These materials have been characterized by X-ray photoelectron spectroscopy (XPS), low-angle X-ray diffraction (XRD), thermogravimetric analysis, nitrogen sorption, transmission electron microscopy (TEM), and scanning electron microscopy (SEM). These analyses confirmed that the carbon mesostructure was maintained after organo-functionalization of the surface and showed the covalent attachment of selective ligands. These new materials, and especially the system with a short spacer between the ligand and the surface, reveal unique Ln selectivity profiles with improved extraction performances for the recovery of lanthanides, in terms of both selectivity and adsorption capacity, and unprecedented stability under acidic conditions.

Functionalization of mesoporous materials for lanthanide and actinide extraction.

Among the energy sources currently available that could address our insatiable appetite for energy and minimize our CO2 emission, solar, wind, and nuclear energy currently occupy an increasing portion of our energy portfolio. The energy associated with these sources can however only be harnessed after mineral resources containing valuable constituents such as actinides (Ac) and rare earth elements (REEs) are extracted, purified and transformed into components necessary for the conversion of energy into electricity. Unfortunately, the environmental impacts resulting from their manufacture including the generation of undesirable and, sometimes, radioactive wastes and the non-renewable nature of the mineral resources, to name a few, have emerged as challenges that should be addressed by the scientific community. In this perspective, the recent development of functionalized solid materials dedicated to selective elemental separation/pre-concentration could provide answers to several of the above-mentioned challenges. This review focuses on recent advances in the field of mesoporous solid-phase (SP) sorbents designed for REEs and Ac liquid-solid extraction. Particular attention will be devoted to silica and carbon sorbents functionalized with commonly known ligands, such as phosphorus or amide-containing functionalities. The extraction performances of these new systems are discussed in terms of sorption capacity and selectivity. In order to support potential industrial applications of the silica and carbon-based sorbents, their main drawbacks and advantages are highlighted and discussed.

A generalized method toward high dispersion of transition metals in large pore mesoporous metal oxide/silica hybrids.

A series of transition metal acetylacetonates and acetates were used as precursors to generate high loadings of metal sites finely dispersed on SBA-15 silica. To achieve this, grafting of chelated transition metal precursors was performed directly to the surface of the as-synthesized SBA-15/P123 composite material. The thus-obtained metal/SBA-15 materials were studied by a variety of methods, e.g., elemental analysis, Fourier transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), scanning electron microscopy (SEM), diffuse reflectance UV-visible spectroscopy (DR-UV-vis), X-ray photoelectron spectroscopy (XPS) and N2 physisorption measurements at -196 °C. From the results, the proposed functionalization method was found to be a highly tunable and reproducible strategy to disperse transition metal oxides in mesoporous silica materials. The results from elemental analysis of the modified materials confirmed that the amount of grafted species is a function of the initial concentration of precursor in the solution used for grafting. The chelated complexes were found to strongly interact with the silanol groups of the silica material, resulting in a ligand-exchange process, as corroborated by FTIR. However, different metal precursors showed distinct reactivity towards the surface of mesoporous silica, owing to differences in the stability of the complexes under the conditions used for grafting. DR-UV-vis and XPS analyses suggest that when the stability of a given precursor decreases, the grafting procedure can lead to the formation of small clusters of the metal oxide on the silica surface. XRD and SEM also show that grafting of lower stability complexes, such as Mn(acac)3, Cu(acetate)2 and VO(acac)2, on the silica surface can result in the formation of large crystals on the external surface of the SBA-15 particles. Nevertheless, it was established by XPS analysis that only a small percentage of the grafted species leads to the formation of bulk crystals while the remaining species are substituted into the silica framework. Obviously, a well-controlled and increased dispersion of the metal cations/oxides on the surface of highly porous silica materials is of great interest since these M(x)O(y)-SiO2 mixed oxides could demonstrate high catalytic activity in a large variety of reactions.