Interplay between the Glass Transition Temperature, Analyte Diffusion, and Fluorescence Quenching for Detection of Nitro-Group Containing Explosives Using Organic Semiconducting Films.

Efficient detection of chemical analytes using fluorescence-based sensors necessitates an in-depth understanding of the physical interaction between the analyte molecules and the sensor films. This study explores the interplay between the thermal properties of a series of triphenylamine-centered fluorescent dendrimers with different glass transition temperatures (Tg) for detecting nitroaromatic explosives. When exposed to 4-nitrotoluene (pNT) vapors, biphasic diffusion kinetics were observed for all the dendrimers, corresponding to Super Case II kinetics, suggesting rapid film swelling during initial analyte uptake. The diffusion kinetics were further analyzed using a diffusion-relaxation model, where a strong Tg dependence was observed for both the initial concentration-driven diffusion phase and the slower film relaxation phase. Additionally, a difference in kinetics between analyte uptake and release was observed. The photoluminescence (PL) kinetics also showed a Tg dependence, with more efficient PL recovery observed for films composed of dendrimers that had a lower Tg. Rapid quenching of over 40% with little PL recovery was seen in the dendrimer with the highest Tg (107 °C), while a smaller quench with efficient PL recovery was observed in the dendrimer that had a Tg close to room temperature. The results highlight the critical role of the thermal properties of sensor films in achieving rapid and sensitive detection.

The impact of film deposition and annealing on the nanostructure and dielectric constant of organic semiconductor thin films.

The strategy of using a bulk-heterojunction light-absorbing layer has led to the most efficient organic solar cells. However, optimising the blend morphology to maximise light absorption, charge generation and extraction can be challenging. Homojunction devices containing a single component have the potential to overcome the challenges associated with bulk heterojunction films. A strategy towards this goal is to increase the dielectric constant of the organic semiconductor to ≈10, which in principle would lead to free charge carrier generation upon photoexcitation. However, the factors that affect the thin film dielectric constants are still not well understood. In this work we report an organic semiconductor material that can be solution processed or vacuum evaporated to form good quality thin films to explore the effect of chromophore structure and film morphology on the dielectric constant and other optoelectronic properties. 2,2'-[(4,4,4',4'-Tetrakis{2-[2-methoxyethoxy]ethyl}-4H,4'H-{2,2'-bi[cyclo-penta[2,1-b:3,4-b']dithiophene]}-6,6'-diyl)bis(methaneylylidene)]dimalononitrile [D(CPDT-DCV)] was designed to have high electron-affinity end groups and low ionisation-potential central moieties. It can be processed from solution or be thermally evaporated, with the film morphology changing from face-on to a herringbone arrangement upon solvent or thermal annealing. The glycol solubilising groups led to the static dielectric constant (taken from capacitance measurements) of the films to be between 6 and 7 (independent of processing conditions), while the optical frequency dielectric constant depended on the processing conditions. The less ordered solution processed film was found to have the lowest optical frequency dielectric constant of 3.6 at 2.0 × 1014 Hz, which did not change upon annealing. In contrast, the more ordered evaporated film had an optical frequency dielectric constant 20% higher at 4.2 and thermal annealing further increased it to 4.5, which is amongst the highest reported for an organic semiconductor at that frequency. Finally, the more ordered evaporated films had more balanced charge transport, which did not change upon annealing.

A statistical approach for modelling the physical process of bacterial attachment to abiotic surfaces.

A statistical approach using a polynomial linear model in combination with a probability distribution model was developed to mathematically represent the process of bacterial attachment and study its mechanism. The linear deterministic model was built based on data from experiments investigating bacterial and substratum surface physico-chemical factors as predictors of attachment. The prediction results were applied to a normal-approximated binomial distribution model to probabilistically predict attachment. The experimental protocol used mixtures of Streptococcus salivarius and Escherichia coli, and mixtures of porous poly(butyl methacrylate-co-ethyl dimethacrylate) and aluminum sec-butoxide coatings, at varying ratios, to allow bacterial attachment to substratum surfaces across a range of physico-chemical properties (including the surface hydrophobicity of bacterial cells and the substratum, the surface charge of the cells and the substratum, the substratum surface roughness and cell size). The model was tested using data from independent experiments. The model indicated that hydrophobic interaction was the most important predictor while reciprocal interactions existed between some of the factors. More importantly, the model established a range for each factor within which the resultant attachment is unpredictable. This model, however, considers bacterial cells as colloidal particles and accounts only for the essential physico-chemical attributes of the bacterial cells and substratum surfaces. It is therefore limited by a lack of consideration of biological and environmental factors. This makes the model applicable only to specific environments and potentially provides a direction to future modelling for different environments.

The structural impact of water sorption on device-quality melanin thin films.

The melanins are a class of pigmentary bio-macromolecules ubiquitous in the biosphere. They possess an intriguing set of physico-chemical properties and have been shown to exhibit hybrid protonic-electronic electrical conductivity, a feature derived from a process termed chemical self-doping driven by the sorption of water. Although the mechanism underlying the electrical conduction has been established, how the sorbed water interacts with the melanin structure at the physical level has not. Herein we use neutron reflectometry to study changes in the structure of synthetic melanin thin films as a function of H2O and D2O vapour pressure. Water is found to be taken up evenly throughout the films, and by employing the contrast effect, the existence of labile protons through reversible deuterium exchange is demonstrated. Finally, we determine a sorption isotherm to enable quantification of the melanin-water interactions.

Elucidating the Spatial Arrangement of Emitter Molecules in Organic Light-Emitting Diode Films.

The effect of varying the emitter concentration on the structural properties of an archetypal phosphorescent blend consisting of 4,4'-bis(N-carbazolyl)biphenyl and tris(2-phenylpyridyl)iridium(III) has been investigated using non-equilibrium molecular dynamics (MD) simulations that mimic the process of vacuum deposition. By comparison with reflectometry measurements, we show that the simulations provide an accurate model of the average density of such films. The emitter molecules were found not to be evenly distributed throughout film, but rather they can form networks that provide charge and/or energy migration pathways, even at emitter concentrations as low as ≈5 weight percent. At slightly higher concentrations, percolated networks form that span the entire system. While such networks would give improved charge transport, they could also lead to more non-radiative pathways for the emissive state and a resultant loss of efficiency.

Detection of Explosive Vapors: The Roles of Exciton and Molecular Diffusion in Real-Time Sensing.

Time-resolved quartz crystal microbalance with in situ fluorescence measurements are used to monitor the sorption of the nitroaromatic (explosive) vapor, 2,4-dinitrotoluene (DNT) into a porous pentiptycene-containing poly(phenyleneethynylene) sensing film. Correlation of the nitroaromatic mass uptake with fluorescence quenching shows that the analyte diffusion follows the Case-II transport model, a film-swelling-limited process, in which a sharp diffusional front propagates at a constant velocity through the film. At a low vapor pressure of DNT of ≈16 ppb, the analyte concentration in the front is sufficiently high to give an average fluorophore-analyte separation of ≈1.5 nm. Hence, a long exciton diffusion length is not required for real-time sensing in the solid state. Rather the diffusion behavior of the analyte and the strength of the binding interaction between the analyte and the polymer play first-order roles in the fluorescence quenching process.

Role of semiconductivity and ion transport in the electrical conduction of melanin.

Melanins are pigmentary macromolecules found throughout the biosphere that, in the 1970s, were discovered to conduct electricity and display bistable switching. Since then, it has been widely believed that melanins are naturally occurring amorphous organic semiconductors. Here, we report electrical conductivity, muon spin relaxation, and electron paramagnetic resonance measurements of melanin as the environmental humidity is varied. We show that hydration of melanin shifts the comproportionation equilibrium so as to dope electrons and protons into the system. This equilibrium defines the relative proportions of hydroxyquinone, semiquinone, and quinone species in the macromolecule. As such, the mechanism explains why melanin at neutral pH only conducts when "wet" and suggests that both carriers play a role in the conductivity. Understanding that melanin is an electronic-ionic hybrid conductor rather than an amorphous organic semiconductor opens exciting possibilities for bioelectronic applications such as ion-to-electron transduction given its biocompatibility.

Determination of fullerene scattering length density: a critical parameter for understanding the fullerene distribution in bulk heterojunction organic photovoltaic devices.

Fullerene derivatives are commonly used as electron acceptors in combination with (macro)molecular electron donors in bulk heterojunction (BHJ) organic photovoltaic (OPV) devices. Understanding the BHJ structure at different electron donor/acceptor ratios is critical to the continued improvement and development of OPVs. The high neutron scattering length densities (SLDs) of the fullerenes provide effective contrast for probing the distribution of the fullerene within the blend in a nondestructive way. However, recent neutron scattering studies on BHJ films have reported a wide range of SLDs ((3.6-4.4) × 10(-6) Å(-2)) for the fullerenes 60-PCBM and 70-PCBM, leading to differing interpretations of their distribution in thin films. In this article, we describe an approach for determining more precisely the scattering length densities of the fullerenes within a polymer matrix in order to accurately quantify their distribution within the active layers of OPV devices by neutron scattering techniques.

Time-resolved neutron reflectometry and photovoltaic device studies on sequentially deposited PCDTBT-fullerene layers.

We have used steady-state and time-resolved neutron reflectometry to study the diffusion of fullerene derivatives into the narrow optical gap polymer poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PCDTBT) to explore the sequential processing of the donor and acceptor for the preparation of efficient organic solar cells. It was found that when [6,6]-phenyl-C61-butyric-acid-methyl-ester (60-PCBM) was deposited onto a thin film of PCDTBT from dichloromethane (DCM), a three-layer structure was formed that was stable below the glass-transition temperature of the polymer. When good solvents for the polymer were used in conjunction with DCM, both 60-PCBM and [6,6]-phenyl-C71-butyric-acid-methyl-ester (70-PCBM) were seen to form films that had a thick fullerene layer containing little polymer and a PCDTBT-rich layer near the interface with the substrate. Devices composed of films prepared by sequential deposition of the polymer and fullerene had efficiencies of up to 5.3%, with those based on 60-PCBM close to optimized bulk heterojunction (BHJ) cells processed in the conventional manner. Sequential deposition of pure components to form the active layer is attractive for large-area device fabrication, and the results demonstrate that this processing method can give efficient solar cells.

Effect of Silyl Ether Bulk on Excited-State Intramolecular Proton Transfer-Based Sensing of Extant Hydrogen Fluoride for G-Series Nerve Agent Detection.

Luminescence-based sensing provides a method for the rapid detection of nerve agents. Previous approaches have generally focused on sensing materials containing a nucleophilic group that can react with the electrophilic phosphorus atom found in nerve agents. Herein we report an alternative approach for the detection of phosphonofluoridate-based G-series nerve agents that utilizes the fact they contain hydrogen fluoride. We have developed silylated sensing materials based on an excited-state intramolecular proton transfer (ESIPT) reporter compound, 2-[benzo[d]thiazol-2-yl]phenol. Thin films of differently silylated 2-[benzo[d]thiazol-2-yl]phenol were found to react with the hydrogen fluoride found in di-iso-propyl fluorophosphate (DFP), a simulant of sarin (G-series nerve agent), and turn on the ESIPT emission of the reporter compound. The use of the ESIPT emission reduced the impact of background fluorescence and improved the sensitivity of the detection. The effectiveness of the approach was dependent on the stability of the silyl protecting group used, with the least sterically hindered (trimethylsilyl) found to be too unstable to the ambient environment while the most sterically hindered, e.g., tri-iso-propylsilyl and tert-butyldiphenylsilyl were found to be insufficiently reactive to be useful in a real detection scenario. The sensing material composed of the tert-butyl dimethylsilyl protected 2-[benzo[d]thiazol-2-yl]phenol was found to have the best balance between stability under ambient conditions, and reactivity and selectivity to hydrogen fluoride. In a 3 s exposure, it could detect hydrogen fluoride down to a concentration of around 23 ppm in DFP with 99% purity.

Reconstructing the 3D Coordinates of Guest:Host OLED Blends with Single Atom Resolution.

The performance of electronic and semiconductor devices is critically dependent on the distribution of guest molecules or atoms in a host matrix. One prominent example is that of organic light-emitting diode (OLED) displays containing phosphorescent emitters, now ubiquitous in handheld devices and high-end televisions. In such OLEDs the phosphorescent guest [normally an iridium(III)-based complex] is typically blended into a host matrix, and charge injection and transport, exciton formation and decay, and hence overall device performance are governed by the distribution of the emissive guest in the host. Here high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) is used with depth sectioning to reconstruct the 3D distribution of emissive iridium(III) complexes, fac-tris(2-phenylpyridine)iridium(III) [Ir(ppy)3], blended into the amorphous host material, tris(4-carbazoyl-9-ylphenyl)amine (TCTA), by resolving the position of each single iridium(III) ion. It is found that most Ir(ppy)3 complexes are clustered with at least one other, even at low concentrations, and that for films of 20 wt.% Ir(ppy)3 essentially all the complexes are interconnected. The results validate the morphology of blend films created using molecular dynamics simulations which mimic the evaporation film-forming process and are also consistent with the experimentally measured charge transport and photophysical properties.

Differentiating Between V- and G-Series Nerve Agent and Simulant Vapours Using Fluorescent Film Responses.

In-field rapid and reliable identification of nerve agents is critical for the protection of Defence and National Security personnel as well as communities. Fluorescence-based detectors can be portable and provide rapid detection of chemical threats. However, most current approaches cannot differentiate between dilute vapors of nerve agent classes and are susceptible to false positives due to the presence of common acids. Here a fluorescence-based method is shown for rapid differentiation between the V-series and phosphonofluoridate G-series nerve agents and avoids false positives due to common acids. Differentiation is achieved through harnessing two different mechanisms. Detection of the V-series is achieved using photoinduced hole transfer whereby the fluorescence of the sensing material is quenched in the presence of the V-series agent. The G-series is detected using a turn-on mechanism in which a silylated excited state intramolecular proton transfer sensing molecule is selectively deprotected by hydrogen fluoride, which is typically found as a contaminant and/or breakdown product in G-series agents such as sarin. The strategy provided discrimination between classes, as the sensor for the G-series agent class is insensitive to the V-series agent, and vice versa, and neither responded to common acids.

Dilute Donor Organic Solar Cells Based on Non-fullerene Acceptors.

The advent of small molecule non-fullerene acceptor (NFA) materials for organic photovoltaic (OPV) devices has led to a series of breakthroughs in performance and device lifetime. The most efficient OPV devices have a combination of electron donor and acceptor materials that constitute the light absorbing layer in a bulk heterojunction (BHJ) structure. For many BHJ-based devices reported to date, the weight ratio of donor to acceptor is near equal. However, the morphology of such films can be difficult to reproduce and manufacture at scale. There would be an advantage in developing a light harvesting layer for efficient OPV devices that contains only a small amount of either the donor or acceptor. In this work we explore low donor content OPV devices composed of the polymeric donor PM6 blended with high performance NFA materials, Y6 or ITIC-4F. We found that even when the donor:acceptor weight ratio was only 1:10, the OPV devices still have good photoconversion efficiencies of around 6% and 5% for Y6 and ITIC-4F, respectively. It was found that neither charge mobility nor recombination rates had a strong effect on the efficiency of the devices. Rather, the overall efficiency was strongly related to the film absorption coefficient and maintaining adequate interfacial surface area between donor and acceptor molecules/phases for efficient exciton dissociation.

The binding and fluorescence quenching efficiency of nitroaromatic (explosive) vapors in fluorescent carbazole dendrimer thin films.

We present a study on three generations of fluorescent carbazole dendrimers that exhibit strong binding with nitroaromatic compounds accompanied by photoluminescence (PL) quenching, making them attractive sensing materials for the detection of explosives such as 2,4,6-trinitrotoluene (TNT). The absorption and release of vapors of the (deuterated) TNT analogue 4-nitrotoluene (pNT) from thin films of the dendrimers were studied with a combination of time-correlated neutron reflectometry and PL spectroscopy. When saturated with pNT the PL of the films was fully quenched and could not be recovered with flowing nitrogen at room temperature but only upon heating to 40-80 °C. Although the majority of the absorbed pNT could be removed with this method the recovered films were found to still contain a residual pNT concentration of ~0.1 molecules per cubic nanometer. However, the proportion of the PL recovered increased with generation with the third generation dendrimer exhibiting close to full recovery despite the presence of residual pNT. This result is attributed to a combination of two effects. First, the dendrimer films present a range of binding sites for nitroaromatic molecules with the stronger binding sites surviving the thermal recovery process. Second, there is a large decrease of the exciton diffusion coefficient with dendrimer generation, preventing migration of the excitation to the remaining bound pNT.

Zinc-Bromine Rechargeable Batteries: From Device Configuration, Electrochemistry, Material to Performance Evaluation.

Zinc-bromine rechargeable batteries (ZBRBs) are one of the most powerful candidates for next-generation energy storage due to their potentially lower material cost, deep discharge capability, non-flammable electrolytes, relatively long lifetime and good reversibility. However, many opportunities remain to improve the efficiency and stability of these batteries for long-life operation. Here, we discuss the device configurations, working mechanisms and performance evaluation of ZBRBs. Both non-flow (static) and flow-type cells are highlighted in detail in this review. The fundamental electrochemical aspects, including the key challenges and promising solutions, are discussed, with particular attention paid to zinc and bromine half-cells, as their performance plays a critical role in determining the electrochemical performance of the battery system. The following sections examine the key performance metrics of ZBRBs and assessment methods using various ex situ and in situ/operando techniques. The review concludes with insights into future developments and prospects for high-performance ZBRBs.

Fluorinated Cation-Based 2D Perovskites for Efficient and Stable 3D/2D Heterojunction Perovskite Solar Cells.

Three-dimensional (3D) perovskite solar cells (PSCs) containing additives capable of forming two-dimensional (2D) structures in neat films have attracted attention due to their ability to enhance power conversion efficiency (PCE) in combination with improved operational stability. Herein, a newly designed fluorinated ammonium salt, 2-(perfluorophenyl)ethanaminium bromide:chloride50:50 (FEABr:Cl50:50), is introduced into CsMAFAPbI3-based PSCs with a standard n-i-p architecture. FEABr:Cl50:50 was used as an additive in the tin(IV) oxide (SnO2) electron transporting layer (ETL) as well as a surface treatment for the perovskite film. Used in this dual way, the additive was found to passivate charge-trapping defects within the SnO2 ETL and regulate the crystal growth of the perovskite layer. When FEABr:Cl50:50 was deposited onto the surface of the 3D perovskite film, it formed a thin hydrophobic 2D capping layer. Adopting this dual strategy led to the perovskite film having larger grain sizes, improved quality, and overall better device performance. As a result, the best-performing device exhibited a PCE of over 23% with negligible hysteresis in an n-i-p device architecture with an area of 0.2 cm2. Furthermore, unencapsulated devices with the hydrophobic 2D capping layer showed improved stability compared to the control device when measured under continuous light irradiation at a maximum power point (MPP) at 80 ± 5 °C in a humid (≈50%) environment.

Perylene Diimide Based Fluorescent Sensors for Drug Simulant Detection: The Effect of Alkyl-Chain Branching on Film Morphology, Exciton Diffusion, Vapor Diffusion, and Sensing Response.

Luminescence-based sensing has been demonstrated to be a powerful method for rapid trace detection of chemical vapors (analytes). Analyte diffusion has been shown to be the critical factor for real-time luminescence-based detection of explosive analytes via photoinduced electron transfer in amorphous films of conjugated polymers and dendrimers. However, similar studies to determine the critical factors for sensing have not been performed on materials that employ photoinduced hole transfer (PHT) to detect low electron affinity analytes such as illicit drugs. Nor have such studies been performed on semicrystalline sensing films. We have developed a family of perylene diimide-based sensing materials capable of undergoing PHT with amine-group containing analytes. It was found that the choice of branched alkyl chain [1-hexylheptyl (PHH), 2-hexyloctyl (PHO), or 2,2-dihexyloctyl (PDHO)] attached to the nitrogen atoms of the imide moiety strongly affected the solution-processed film morphology. PHH and PHO were found to contain crystalline phases, whereas PDHO was essentially amorphous. The degree of crystallinity strongly influenced exciton diffusion, with PHH and PHO exhibiting exciton diffusion coefficients that were 20× and 10× greater than the value of the amorphous PDHO. The degree of film crystallinity was also found to be critical when the films were applied to detect N-methylphenethylamine (MPEA), a simulant of methamphetamine. While PHH had the largest exciton diffusion coefficient [(1.0 ± 0.2) × 10-2 cm2 s-1] and analyte uptake (12.3 ± 1.8 ng) it showed the smallest quenching efficiency (2.6% ng-1). In contrast, PHO, which sorbed the least analyte (6.1 ± 0.4 ng) of the three compounds, had the largest quenching efficiency (7.1% ng-1) due to its molecular packing and hence exciton diffusion coefficient [(4.5 ± 1.4) × 10-3 cm2 s-1] not being affected by sorption of the analyte. These results show that when applying fluorescent films in practical detection scenarios there is a potential trade-off between a high exciton diffusion constant and analyte diffusion for semicrystalline sensing materials and that a high exciton diffusion coefficient in an as-cast film does not necessarily translate into a more efficient fluorescent quenching. The results also show that sensing materials that form semicrystalline films, whose packing is not disrupted by analyte diffusion, provide a route for overcoming these effects and achieving high sensitivity.

Scientific issues of zinc-bromine flow batteries and mitigation strategies.

Zinc-bromine flow batteries (ZBFBs) are promising candidates for the large-scale stationary energy storage application due to their inherent scalability and flexibility, low cost, green, and environmentally friendly characteristics. ZBFBs have been commercially available for several years in both grid scale and residential energy storage applications. Nevertheless, their continued development still presents challenges associated with electrodes, separators, electrolyte, as well as their operational chemistry. Therefore, rational design of these components in ZBFBs is of utmost importance to further improve the overall device performance. In this review, the focus is on the scientific understanding of the fundamental electrochemistry and functional components of ZBFBs, with an emphasis on the technical challenges of reaction chemistry, development of functional materials, and their application in ZBFBs. Current limitations of ZBFBs with future research directions in the development of high performance ZBFBs are suggested.

Nitrogen-doped carbon monolith for alkaline supercapacitors and understanding nitrogen-induced redox transitions.

A nitrogen-doped porous carbon monolith was synthesized as a pseudo-capacitive electrode for use in alkaline supercapacitors. Ammonia-assisted carbonization was used to dope the surface with nitrogen heteroatoms in a way that replaced carbon atoms but kept the oxygen content constant. Ammonia treatment expanded the micropore size-distributions and increased the specific surface area from 383 m(2) g(-1) to 679 m(2) g(-1). The nitrogen-containing porous carbon material showed a higher capacitance (246 F g(-1)) in comparison with the nitrogen-free one (186 F g(-1)). Ex situ electrochemical spectroscopy was used to investigate the evolution of the nitrogen-containing functional groups on the surface of the N-doped carbon electrodes in a three-electrode cell. In addition, first-principles calculations were explored regarding the electronic structures of different nitrogen groups to determine their relative redox potentials. We proposed possible redox reaction pathways based on the calculated redox affinity of different groups and surface analysis, which involved the reversible attachment/detachment of hydroxy groups between pyridone and pyridine. The oxidation of nitrogen atoms in pyridine was also suggested as a possible reaction pathway.

A microporous-mesoporous carbon with graphitic structure for a high-rate stable sulfur cathode in carbonate solvent-based Li-S batteries.

A microporous-mesoporous carbon with graphitic structure was developed as a matrix for the sulfur cathode of a Li-S cell using a mixed carbonate electrolyte. Sulfur was selectively introduced into the carbon micropores by a melt adsorption-solvent extraction strategy. The micropores act as solvent-restricted reactors for sulfur lithiation that promise long cycle stability. The mesopores remain unfilled and provide an ion migration pathway, while the graphitic structure contributes significantly to low-resistance electron transfer. The selective distribution of sulfur in micropores was characterized by X-ray photoelectron spectroscopy (XPS), nitrogen cryosorption analysis, transmission electron microscopy (TEM), X-ray powder diffraction and Raman spectroscopy. The high-rate stable lithiation-delithiation of the carbon-sulfur cathode was evaluated using galvanostatic charge-discharge tests, cyclic voltammetry and electrochemical impedance spectroscopy. The cathode is able to operate reversibly over 800 cycles with a 1.8 C discharge-recharge rate. This integration of a micropore reactor, a mesopore ion reservoir, and a graphitic electron conductor represents a generalized strategy to be adopted in research on advanced sulfur cathodes.