Methacrylate saccharide-based monomers for dental adhesive systems.

The aim of this in vitro study was to synthesize three new methacrylate monomers based on the modification of saccharides structures (glucose-Gluc, sucrose-Sucr and chitosan-Chit) with glycidyl methacrylate, and to use them in the composition of dental adhesives. Three methacrylate saccharide monomers were synthesized and characterized by mid-IR, 1H and 13C NMR, antioxidant activity and cytotoxic effect. Monomers included: one monosaccharide - Gluc-MA; one disaccharide - Sucr-MA; and one polysaccharide - Chit-MA. Primers containing HEMA, methacrylate saccharide monomers at concentrations of 0 (control), 1, 2 or 4 wt%, 60 wt% ethanol aqueous solution (pH3.0) and initiator system were formulated. Primers were used in conjunction with a bond step and composite paste to restore caries-free third molars, and dentin bond strength (24 hours and 6 month of storage in water), and antimicrobial activity (Alamar Blue test) were tested. Degree of conversion (DC) and maximum rate of polymerization (Rpmax) of the primers themselves were also analyzed. The mid-IR, 1H and 13C spectrum confirmed the presence of vinyl group on the structure of saccharides. Chit-MA showed low antioxidant activity and did not present a cytotoxic effect. Gluc-MA and Sucr-MA possess antioxidant and cytotoxic activity, concentration dependent. In the presence of methacrylate saccharide monomers, the primers showed DC comparable to the control group, except Gluc-MA4%, Sucr-MA4% and Chit-MA1%, which showed a range of 64.6 from 58.5 %DC. Rpmax was not statistically different for all the groups (p = 0.01). The bond strength of Sucr-MA1% increased from 25.7 (±2.8) to 40.6 (±5.3) MPa after 6 months of storage. All the synthesized monomers showed some antimicrobial activity after polymerization. Gluc-MA and Chit-MA 4% and Sucr-MA 1, 2 and 4% led to decrease bacterial metabolism. Sucr-MA 1% showed better results regarding the decrease in bacterial metabolism and increasing the bond strength after 6 months of storage.

SPR platform based on image acquisition for HER2 antigen detection.

HER2 antigen is a marker used for breast cancer diagnosis and prevention. Its determination has great importance since breast cancer is one of the most insidious types of cancer in women. HER2 antigen assessment in human serum is traditionally achieved by enzyme-linked immunosorbent assay (ELISA method), but it has some disadvantages, such as suppressing the thermodynamic-kinetic studies regarding the antibody-antigen interaction, and the use of labeled molecules that can promote false positive responses. Biosensors based on surface plasmon resonance (SPR) are sensitive optical techniques widely applied on bioassays. The plasmonic devices do not operate with labeled molecules, overcoming conventional immunoassay limitations, and enabling a direct detection of target analytes. In this way, a new SPR biosensor to assess HER2 antigen has been proposed, using nanohole arrays on a gold thin film by signal transduction of transmitted light measurements from array image acquisitions. These metallic nanostructures may couple the light directly on surface plasmons using a simple collinear arrangement. The proposed device reached an average sensitivity for refractive index (RI) variation on a metal surface of 4146 intensity units/RIU (RIU = RI units). The device feasibility on biomolecular assessment was evaluated. For this, 3 ng ml-1 known HER2 antigen concentration was efficiently flowed (using a microfluidic system) and detected from aqueous solutions. This outcome shows that the device may be a powerful apparatus for bioassays, particularly toward breast cancer diagnosis and prognosis.

Attomolar protein detection using in-hole surface plasmon resonance.

An in-hole nanohole surface plasmon resonance sensing scheme is demonstrated. Arrays of periodic nanoholes milled through thin layers of SiO(x) and gold were used to detect the binding of organic and biological molecules inside the nanoholes, while blocking the gold surfaces outside the holes. This new approach is more efficient than the previous nanohole array method, where the response was related to binding events taking place inside of the holes and on the top gold surface. The improved sensitivity to binding events and lower detection limit are related to resonant surface plasmon enhanced transmission through the arrays of nanoholes. The sensitivity was found to be 650 nm/RIU and the detection of three attomoles of proteins was estimated from this scheme.

Nanoholes as nanochannels: flow-through plasmonic sensing.

We combine nanofluidics and nanoplasmonics for surface-plasmon resonance (SPR) sensing using flow-through nanohole arrays. The role of surface plasmons on resonant transmission motivates the application of nanohole arrays as surface-based biosensors. Research to date, however, has focused on dead-ended holes, and therefore failed to harness the benefits of nanoconfined transport combined with SPR sensing. The flow-through format enables rapid transport of reactants to the active surface inside the nanoholes, with potential for significantly improved time of analysis and biomarker yield through nanohole sieving. We apply the flow-through method to monitor the formation of a monolayer and the immobilization of an ovarian cancer biomarker specific antibody on the sensing surface in real-time. The flow-through method resulted in a 6-fold improvement in response time as compared to the established flow-over method.

Impact of thiourethane filler surface functionalization on composite properties.

Thiourethane oligomers added to methacrylate matrices improve fracture toughness and reduce polymerization stress. In this study, the oligomers are added to the surface of inorganic fillers in the formulation of resin composites. Systematically varied fillers treated either with the thiourethane or a methacrylate silane control are tested. Thiourethane reduces the rate of polymerization of light-cured composites but does not affect the final degree of conversion (DC). Filler functionalization with thiourethane increases the depth of polymerization, in filler type-dependent fashion. Thiourethane reduces the polymerization stress for all fillers. The findings suggest that this approach results in the same general effects with the addition of thiourethanes directly to the matrix. This is accomplished with a lower overall concentration of thiourethane, and with no prejudice to the handling characteristics of the material.

Effect of thiourethane filler surface functionalization on stress, conversion and mechanical properties of restorative dental composites.

OBJECTIVES: This study evaluated the efficacy of a thiourethane(TU)-modified silane agent in improving properties in filled composites. METHODS: The TU-silane agent was synthesized by combining 1,3-bis(1-isocyanato-1-methylethyl)benzene and 3-(triethoxysilyl)propyl isocyanate with trimethylol-tris-3-mercaptopropionate (TMP), at 1:2 isocyanate:thiol, leaving pendant thiol and alkoxy silane groups. Barium glass fillers (1µm average particle size) were functionalized with 5wt% TU-silane in an acidic ethanol solution. Commercially available 3-(trimethoxysilyl)propyl methacrylate (MA-silane) and (3-mercaptopropyl)trimethoxysilane (SH-silane), as well as no silane treatment (NO-silane), were used as controls. Composites were made with BisGMA-UDMA-TEGDMA (5:3:2), camphorquinone/ethyl-4-dimethylaminobenzoate (0.2/0.8wt%) and di-tert-butyl hydroxytoluene (0.3wt%) and 70wt% silanated inorganic fillers. Polymerization stress (PS) was measured using a cantilever beam apparatus (Bioman). Methacrylate conversion (DC) and rate of polymerization (RP) during photoactivation (800mW/cm2) were followed in real-time with near-IR. Flexural strength/modulus (FS/FM) were evaluated in three-point bending with 2×2×25 mm. STATISTICAL ANALYSIS: 2-way ANOVA/Tukey's test (α=5%). RESULTS: DC, Rpmax and E were similar for all groups tested. FS was similar for the TU- and MA-silane, which were statistically higher than the untreated and SH-silane groups. Stress reductions in relation to the MA-silane were observed for all groups, but statistically more markedly for the TU-silane material. This is likely due to stress relaxation and/or toughening provided at the filler interface by the oligomeric TU structure. SIGNIFICANCE: TU-silane oligomers favorably modified conventional dimethacrylate networks with minimal disruption to existing curing chemistry, in filled composites. For the same conversion values, stress reductions of up to 50% were observed, without compromise to mechanical properties or handling characteristics.

Novel urethane-based polymer for dental applications with decreased monomer leaching.

The aim of this study was to synthesize and characterize new multifunctional-urethane-methacrylate monomers to be used as the organic matrix in restorative dental composites, and evaluate the main physical-chemical properties of the resulting material. Bis-GMA (bisphenol-A-diglycidylmethacrylate) and GDMA (glycerol dimethacrylate) were modified by reacting the hydroxyl groups with isocyanate groups of urethane-methacrylate precursors to result in the new monomeric systems U-(bis-GMA)-Mod and U-(GDMA)-Mod, U=Urethane and Mod=Modified. The modifications were characterized by FTIR and 1H NMR. The final monomeric synthesized system was used to prepare dental resins and composites. The physical-chemical properties were evaluated and compared with those of bis-GMA composites with varying filler contents or unfilled resins. U-(bis-GMA)-Mod and U-(GDMA)-Mod can be used to prepare dental restorative composites, with some foreseeable advantages compared with bis-GMA composites. One significant advantage is that these composites have the potential to be less toxic, once they presented a reduction of 50% in leaching of unreacted monomers extracted by solvent.

Preparation and cytotoxicity of N,N,N-trimethyl chitosan/alginate beads containing gold nanoparticles.

Polyelectrolyte complex beads based on N,N,N-trimethyl chitosan (TMC) and sodium alginate (ALG) were obtained. This biomaterial was characterised by FTIR, TGA/DTG, DSC and SEM analysis. The good properties of polyelectrolyte complex hydrogel beads were associated, for the first time, with gold nanoparticles (AuNPs). Through a straightforward methodology, AuNPs were encapsulated into the beads. The in vitro cytotoxicity assays on the Caco-2 colon cancer cells and healthy VERO cells showed that the beads presented good biocompatibility on both cell lines, whereas the beads loaded with gold nanoparticles (beads/AuNPs) was slightly cytotoxic on the Caco-2 and VERO cells.

Polyelectrolyte complex containing silver nanoparticles with antitumor property on Caco-2 colon cancer cells.

Polyelectrolyte complex (beads) based on N,N,N-trimethyl chitosan/alginate was successful obtained and silver nanoparticles (AgNPs) were loaded within beads. In vitro cytotoxicity assays using beads/silver nanoparticles (beads/AgNPs) provided results, indicating that this material significantly inhibited the growth of colon cancer cells (Caco-2). In vitro release studies showed that the beads stabilized AgNPs and repressed Ag(0) oxidation under gastric conditions (pH 2.0). On the other hand, at physiological condition (pH 7.4) the beads/AgNPs released 3.3 µg of Ag(+) per each beads milligram. These studies showed that the concentration of Ag(+) released (3.3 µg) was cytotoxic for the Caco-2 cells and was not cytotoxic on healthy VERO cells. This result opens new perspectives for the manufacture of biomaterials based on beads/AgNPs with anti-tumor properties.

A urethane-based multimethacrylate mixture and its use in dental composites with combined high-performance properties.

OBJECTIVES: To synthesize and characterize different molar weight urethane multimethacrylates with a single stage (one-pot) procedure. To prepare and characterize the properties of related composites. METHODS: Two methacrylate precursors were initially synthesized. Then, these precursors and the multimethacrylate system formed by their coupling were characterized by FTIR and (1)H NMR. The final product was used as a matrix (with TEGDMA and SiO2 silanized microparticles) in the preparation of composites and their physical and mechanical properties were compared to those of a bis-GMA-based resin. Water sorption and solubility measurements of the composites were also performed. RESULTS: FTIR and NMR suggested that the proposed synthesis route yields a mixture of mainly urethane-di, -tri, and tetramethacrylates. The composites presented low polymerization shrinkage (e.g. 1.88±0.08% for a resin with 70% of SiO2) and high flexural strength (e.g. 124.74±9.68 MPa for a resin with 65% of SiO2) when compared to the bis-GMA based resin and other composites found to date. Water sorption and solubility results show that the composites were deemed compliant with ISO 4049 requirements. SIGNIFICANCE: The mixture containing different molar weight of urethane multimethacrylates showed to be an excellent substitute for bis-GMA, achieving an equilibrium of properties (unlike reports elsewhere which show the enhancement of some parameters in detriment to others) and composites with low polymerization shrinkage, suitable microhardness and degree of conversion, and up to standard water sorption/solubility and flexural strength.