Electrolyte design for Li-ion batteries under extreme operating conditions.

The ideal electrolyte for the widely used LiNi0.8Mn0.1Co0.1O2 (NMC811)||graphite lithium-ion batteries is expected to have the capability of supporting higher voltages (≥4.5 volts), fast charging (≤15 minutes), charging/discharging over a wide temperature range (±60 degrees Celsius) without lithium plating, and non-flammability1-4. No existing electrolyte simultaneously meets all these requirements and electrolyte design is hindered by the absence of an effective guiding principle that addresses the relationships between battery performance, solvation structure and solid-electrolyte-interphase chemistry5. Here we report and validate an electrolyte design strategy based on a group of soft solvents that strikes a balance between weak Li+-solvent interactions, sufficient salt dissociation and desired electrochemistry to fulfil all the aforementioned requirements. Remarkably, the 4.5-volt NMC811||graphite coin cells with areal capacities of more than 2.5 milliampere hours per square centimetre retain 75 per cent (54 per cent) of their room-temperature capacity when these cells are charged and discharged at -50 degrees Celsius (-60 degrees Celsius) at a C rate of 0.1C, and the NMC811||graphite pouch cells with lean electrolyte (2.5 grams per ampere hour) achieve stable cycling with an average Coulombic efficiency of more than 99.9 per cent at -30 degrees Celsius. The comprehensive analysis further reveals an impedance matching between the NMC811 cathode and the graphite anode owing to the formation of similar lithium-fluoride-rich interphases, thus effectively avoiding lithium plating at low temperatures. This electrolyte design principle can be extended to other alkali-metal-ion batteries operating under extreme conditions.

Validation of the polarized Monte Carlo model of shipborne oceanic lidar returns.

The polarized Monte Carlo (PMC) model has been applied to study the backscattering measurement of oceanic lidar. This study proposes a PMC model for shipborne oceanic lidar simulation. This model is validated by the Rayleigh scattering experiment, lidar equation, and in-situ lidar LOOP (Lidar for Ocean Optics Profiler) returns [Opt. Express30, 8927 (2022)10.1364/OE.449554]. The relative errors of the simulated Rayleigh scattering results are less than 0.07%. The maximum mean relative error (MRE) of the simulated single scattering scalar signals and lidar equation results is 30.94%. The maximum MRE of simulated total scattering signals and LOOP returns in parallel and cross channels are 33.29% and 22.37%, respectively, and the maximal MRE of the depolarization ratio is 24.13%. The underwater light field of the laser beam is also simulated to illustrate the process of beam energy spreading. These results prove the validity of the model. Further analyses show that the measured signals of shipborne lidar LOOP are primarily from the particle single scatterings. This model is significant for analyzing the signal contributions from multiple scattering and single scattering.

Scattering direction sampling methods for polarized Monte Carlo simulation of oceanic lidar.

Monte Carlo techniques have been widely applied in polarized light simulation. Based on different preconditions, there are two main types of sampling strategies for scattering direction: one is the scalar sampling method; the others are polarized sampling approaches, including the one- and two-point rejection methods. The polarized simulation of oceanic lidar involves a variety of mediums, and an efficient scattering sampling method is the basis for the coupling simulation of the atmosphere and ocean. To determine the optimal scattering sampling method for oceanic lidar simulation, we developed a polarized Monte Carlo model and simulated Mie scattering, Rayleigh scattering, and Petzold average-particle scattering experiments. This simulation model has been validated by comparison with Ramella-Roman's program [Opt. Express13, 4420 (2005)OPEXFF1094-408710.1364/OPEX.13.004420], with differences in reflectance and transmittance Stokes less than 1% in Mie scattering. The simulation results show these scattering sampling methods differ in runtime, scattering angle distributions, and reflectance and transmittance Stokes. Considering the current simulation accuracy of oceanic lidar, the differences in reflectance and transmittance Stokes are acceptable; thus, the runtime becomes the main evaluation factor. The one-point rejection method and scalar sampling method are preferable for the oceanic lidar polarized simulation. Under complex atmosphere-ocean coupling systems, scalar sampling methods may be a better choice since the calculation process of the sampling is independent of the incident Stokes vector.

Intelligent diagnosis with Chinese electronic medical records based on convolutional neural networks.

BACKGROUND: Benefiting from big data, powerful computation and new algorithmic techniques, we have been witnessing the renaissance of deep learning, particularly the combination of natural language processing (NLP) and deep neural networks. The advent of electronic medical records (EMRs) has not only changed the format of medical records but also helped users to obtain information faster. However, there are many challenges regarding researching directly using Chinese EMRs, such as low quality, huge quantity, imbalance, semi-structure and non-structure, particularly the high density of the Chinese language compared with English. Therefore, effective word segmentation, word representation and model architecture are the core technologies in the literature on Chinese EMRs. RESULTS: In this paper, we propose a deep learning framework to study intelligent diagnosis using Chinese EMR data, which incorporates a convolutional neural network (CNN) into an EMR classification application. The novelty of this paper is reflected in the following: (1) We construct a pediatric medical dictionary based on Chinese EMRs. (2) Word2vec adopted in word embedding is used to achieve the semantic description of the content of Chinese EMRs. (3) A fine-tuning CNN model is constructed to feed the pediatric diagnosis with Chinese EMR data. Our results on real-world pediatric Chinese EMRs demonstrate that the average accuracy and F1-score of the CNN models are up to 81%, which indicates the effectiveness of the CNN model for the classification of EMRs. Particularly, a fine-tuning one-layer CNN performs best among all CNNs, recurrent neural network (RNN) (long short-term memory, gated recurrent unit) and CNN-RNN models, and the average accuracy and F1-score are both up to 83%. CONCLUSION: The CNN framework that includes word segmentation, word embedding and model training can serve as an intelligent auxiliary diagnosis tool for pediatricians. Particularly, a fine-tuning one-layer CNN performs well, which indicates that word order does not appear to have a useful effect on our Chinese EMRs.

PKM2 promotes glucose metabolism through a let-7a-5p/Stat3/hnRNP-A1 regulatory feedback loop in breast cancer cells.

Tumor cells metabolize more glucose to lactate in aerobic or hypoxic conditions than normal cells. Pyruvate kinase isoenzyme type M2 (PKM2) is crucial for tumor cell aerobic glycolysis. We established a role for let-7a-5p/Stat3/hnRNP-A1/PKM2 signaling in breast cancer cell glucose metabolism. PKM2 depletion via small interfering RNA (siRNA) inhibits cell proliferation and aerobic glycolysis in breast cancer cells. Signal transducer and activator of transcription 3 (Stat3) promotes upregulation of heterogeneous nuclear ribonucleoprotein (hnRNP)-A1 expression, hnRNP-A1 binding to pyruvate kinase isoenzyme (PKM) pre messenger RNA, and the subsequent formation of PKM2. This pathway is downregulated by the microRNA let-7a-5p, which functionally targets Stat3, whereas hnRNP-A1 blocks the biogenesis of let-7a-5p to counteract its ability to downregulate the Stat3/hnRNP-A1/PKM2 signaling pathway. The downregulation of Stat3/hnRNP-A1/PKM2 by let-7a-5p is verified using a breast cancer. These results suggest that let-7a-5p, Stat3, and hnRNP-A1 form a feedback loop, thereby regulating PKM2 expression to modulate glucose metabolism of breast cancer cells. These findings elucidate a new pathway mediating aerobic glycolysis in breast cancers and provide an attractive potential target for breast cancer therapeutic intervention.

3,4-Dimethoxycinnamic Acid as a Novel Matrix for Enhanced In Situ Detection and Imaging of Low-Molecular-Weight Compounds in Biological Tissues by MALDI-MSI.

Low-molecular-weight (low-MW) compounds have many essential functions in biological processes, and the molecular imaging of as many low-MW compounds as possible is critical for understanding complex biological processes. Matrix-assisted laser desorption/ionization mass spectrometry imaging (MALDI-MSI) is an emerging molecular-imaging technology that enables determination of the spatial distributions and the relative abundances of diverse endogenous compounds in tissues. New matrices suitable for the imaging of low-MW compounds by MALDI-MSI are important for the technological advancement of tissue imaging. In this study, 3,4-dimethoxycinnamic acid (DMCA) was evaluated as a new matrix for enhanced low-MW compound detection by MALDI-MSI because of its strong ultraviolet absorption, low matrix-ion related interferences below m/ z 500, and high ionization efficiency for the analysis of low-MW compounds. DMCA was successfully used for improved in situ detection of low-molecular-weight metabolites ( m/ z < 500) and lipids in rat liver, rat brain, and germinating Chinese-yew seed tissue sections. The use of DMCA led to the successful in situ detection of 303, 200, and 248 low-MW compound ion signals from these three tissues, respectively. Both MALDI-MS/MS and LC-MS/MS were used to identify these ion signals, leading to the identification of 115 low-MW compounds from rat liver (including 53 lipids, 29 oligopeptides, and 33 metabolites), 130 low-MW compounds from rat brain (including 104 lipids, 5 oligopeptides, and 21 metabolites), and 111 low-MW compounds from germinating Chinese-yew seeds (including 77 lipids, 22 oligopeptides, 8 flavonoids, and 4 alkaloids). A larger number of low-MW compounds could be detected and imaged when DMCA was used as the MALDI matrix than with other commonly used MALDI matrices such as 2,5-dihydroxybenzoic acid, α-cyano-4-hydroxycinnamic acid, 2-mercaptobenzothiazole, graphene oxide, and silver nanoparticles. Our work provides a new and powerful matrix for enhanced MALDI-MS profiling of low-MW compounds in both animal and plant tissues.

Tuning the electronic properties of the γ-Al2O3 surface by phosphorus doping.

Tuning the electronic properties of oxide surfaces is of pivotal importance, because they find applicability in a variety of industrial processes, including catalysis. Currently, the industrial protocols for synthesizing oxide surfaces are limited to only partial control of the oxide's properties. This is because the ceramic processes result in complex morphologies and a priori unpredictable behavior of the products. While the bulk doping of alumina surfaces has been demonstrated to enhance their catalytic applications (i.e. hydrodesulphurization (HDS)), the fundamental understanding of this phenomenon and its effect at an atomic level remain unexplored. In our joint experimental and computational study, simulations based on Density Functional Theory (DFT), synthesis, and a variety of surface characterization techniques are exploited for the specific goal of understanding the structure-function relationship of phosphorus-doped γ-Al2O3 surfaces. Our theoretical calculations and experimental results agree in finding that P doping of γ-Al2O3 leads to a significant decrease in its work function. Our computational models show that this decrease is due to the formation of a new surface dipole, providing a clear picture of the effect of P doping at the surface of γ-Al2O3. In this study, we uncover a general paradigm for tuning support-catalyst interactions that involves electrostatic properties of doped γ-Al2O3 surface, specifically the surface dipole. Our findings open a new pathway for engineering the electronic properties of metal oxides' surfaces.

Recent advances in matrix-assisted laser desorption/ionisation mass spectrometry imaging (MALDI-MSI) for in situ analysis of endogenous molecules in plants.

INTRODUCTION: Mass spectrometry imaging (MSI) as a label-free and powerful imaging technique enables in situ evaluation of a tissue metabolome and/or proteome, becoming increasingly popular in the detection of plant endogenous molecules. OBJECTIVE: The characterisation of structure and spatial information of endogenous molecules in plants are both very important aspects to better understand the physiological mechanism of plant organism. METHODS: Matrix-assisted laser desorption/ionization mass spectrometry imaging (MALDI-MSI) is a commonly-used tissue imaging technique, which requires matrix to assist in situ detection of a variety of molecules on the surface of a tissue section. In previous studies, MALDI-MSI was mostly used for the detection of molecules from animal tissue sections, compared to plant samples due to cell structural limitations, such as plant cuticles, epicuticular waxes, and cell walls. Despite the enormous progress that has been made in tissue imaging, there is still a challenge for MALDI-MSI suitable for the imaging of endogenous compounds in plants. RESULTS: This review summarises the recent advances in MALDI-MSI, focusing on the application of in situ detection of endogenous molecules in different plant organs, i.e. root, stem, leaf, flower, fruit, and seed. CONCLUSION: Further improvements on instrumentation sensitivity, matrix selection, image processing and sample preparation will expand the application of MALDI-MSI in plant research.

Pd-Catalyzed Suzuki-Miyaura Cross-Coupling of Pentafluorophenyl Esters.

Although the palladium-catalyzed Suzuki-Miyaura cross-coupling of aryl esters has received significant attention, there is a lack of methods that utilize cheap and readily accessible Pd-phosphane catalysts, and can be routinely carried out with high cross-coupling selectivity. Herein, we report the first general method for the cross-coupling of pentafluorophenyl esters (pentafluorophenyl = pfp) by selective C⁻O acyl cleavage. The reaction proceeds efficiently using Pd(0)/phosphane catalyst systems. The unique characteristics of pentafluorophenyl esters are reflected in the fully selective cross-coupling vs. phenolic esters. Of broad synthetic interest, this report establishes pentafluorophenyl esters as new, highly reactive, bench-stable, economical, ester-based, electrophilic acylative reagents via acyl-metal intermediates. Mechanistic studies strongly support a unified reactivity scale of acyl electrophiles by C(O)⁻X (X = N, O) activation. The reactivity of pfp esters can be correlated with barriers to isomerization around the C(acyl)⁻O bond.

Graphene-Catalyzed Direct Friedel-Crafts Alkylation Reactions: Mechanism, Selectivity, and Synthetic Utility.

Transition-metal-catalyzed alkylation reactions of arenes have become a central transformation in organic synthesis. Herein, we report the first general strategy for alkylation of arenes with styrenes and alcohols catalyzed by carbon-based materials, exploiting the unique property of graphenes to produce valuable diarylalkane products in high yields and excellent regioselectivity. The protocol is characterized by a wide substrate scope and excellent functional group tolerance. Notably, this process constitutes the first general application of graphenes to promote direct C-C bond formation utilizing polar functional groups anchored on the GO surface, thus opening the door for an array of functional group alkylations using benign and readily available graphene materials. Mechanistic studies suggest that the reaction proceeds via a tandem catalysis mechanism in which both of the coupling partners are activated by interaction with the GO surface.

Microwave Enabled One-Pot, One-Step Fabrication and Nitrogen Doping of Holey Graphene Oxide for Catalytic Applications.

The unique properties of a holey graphene sheet, referred to as a graphene sheet with nanoholes in its basal plane, lead to wide range of applications that cannot be achieved by its nonporous counterpart. However, the large-scale solution-based production requires graphene oxide (GO) or reduced GO (rGO) as the starting materials, which take hours to days for fabrication. Here, an unexpected discovery that GO with or without holes can be controllably, directly, and rapidly (tens of seconds) fabricated from graphite powder via a one-step-one-pot microwave assisted reaction with a production yield of 120 wt% of graphite is reported. Furthermore, a fast and low temperature approach is developed for simultaneous nitrogen (N) doping and reduction of GO sheets. The N-doped holey rGO sheets demonstrate remarkable electrocatalytic capabilities for the electrochemical oxygen reduction reaction. The existence of the nanoholes provides a "short cut" for efficient mass transport and dramatically increases edges and surface area, therefore, creates more catalytic centers. The capability of rapid fabrication and N-doping as well as reduction of holey GO can lead to development of an efficient catalyst that can replace previous coin metals for energy generation and storage, such as fuel cells and metal-air batteries.

Self-assembled organic nanowires for high power density lithium ion batteries.

The electroactive organic materials are promising alternatives to inorganic electrode materials for the new generation of green Li-ion batteries due to their sustainability, environmental benignity, and low cost. Croconic acid disodium salt (CADS) was used as Li-ion battery electrode, and CADS organic wires with different diameters were fabricated through a facile synthetic route using antisolvent crystallization method to overcome the challenges of low electronic conductivity of CADS and lithiation induced strain. The CADS nanowire exhibits much better electrochemical performance than its crystal bulk material and microwire counterpart. CADS nanowire with a diameter of 150 nm delivers a reversible capability of 177 mAh g(-1) at a current density of 0.2 C and retains capacity of 170 mAh g(-1) after 110 charge/discharge cycles. The nanowire structure also remarkably enhances the kinetics of croconic acid disodium salt. The CADS nanowire retains 50% of the 0.1 C capacity even when the current density increases to 6 C. In contrast, the crystal bulk and microwire material completely lose their capacities when the current density merely increases to 2 C. Such a high rate performance of CADS nanowire is attributed to its short ion diffusion pathway and large surface area, which enable fast ion and electron transport in the electrode. The theoretical calculation suggests that lithiation of CADS experiences an ion exchange process. The sodium ions in CADS will be gradually replaced by lithium ions during the lithiation and delithiation of CADS electrode, which is confirmed by inductively coupled plasma test.

Hypoxia and Singlet Oxygen Dual-Responsive Micelles for Photodynamic and Chemotherapy Therapy Featured with Enhanced Cellular Uptake and Triggered Cargo Delivery.

Introduction: Combination therapy provides better outcomes than a single therapy and becomes an efficient strategy for cancer treatment. In this study, we designed a hypoxia- and singlet oxygen-responsive polymeric micelles which contain azo and nitroimidazole groups for enhanced cellular uptake, repaid cargo release, and codelivery of photosensitizer Ce6 and hypoxia-activated prodrug tirapazamine TPZ (DHM-Ce6@TPZ), which could be used for combining Ce6-mediated photodynamic therapy (PDT) and PDT-activated chemotherapy to enhance the therapy effect of cancer. Methods: The hypoxia- and singlet oxygen-responsive polymeric micelles DHM-Ce6@TPZ were prepared by film hydration method. The morphology, physicochemical properties, stimuli responsiveness, in vitro singlet oxygen production, cellular uptake, and cell viability were evaluated. In addition, the in vivo therapeutic effects of the micelles were verified using a tumor xenograft mice model. Results: The resulting dual-responsive micelles not only increased the concentration of intracellular photosensitizer and TPZ, but also facilitated photosensitizer and TPZ release for enhanced integration of photodynamic and chemotherapy therapy. As a photosensitizer, Ce6 induced PDT by generating toxic singlet reactive oxygen species (ROS), resulting in a hypoxic tumor environment to activate the prodrug TPZ to achieve efficient chemotherapy, thereby evoking a synergistic photodynamic and chemotherapy therapeutic effect. The cascade synergistic therapeutic effect of DHM-Ce6@TPZ was effectively evaluated both in vitro and in vivo to inhibit tumor growth in a breast cancer mice model. Conclusion: The designed multifunctional micellar nano platform could be a convenient and powerful vehicle for the efficient co-delivery of photosensitizers and chemical drugs for enhanced synergistic photodynamic and chemotherapy therapeutic effect of cancer.

Robust and aligned carbon nanotube/titania core/shell films for flexible TCO-free photoelectrodes.

Carbon nanotube (CNT)/semiconducting oxide hybrids are an ideal architecture for light-harvesting devices, in which the CNTs are expected to not only act as a scaffold but also provide fast transport paths for photogenerated charges in the oxide. However, the current potential of CNTs for charge transport is largely suppressed due to the nanotubes not being interconnected but isolated by the low conductive oxide coatings. Herein, a flexible and conductive CNT/TiO(2) core/shell heterostructure film is reported, with aligned and interconnected CNTs wrapped in a continuous TiO(2) coating. Without using additional transparent conducting oxide (TCO) substrates, this unique feature of the film boosts the incident photon-to-electron conversion efficiency to 32%, outperforming TiO(2) nanoparticle electrodes fabricated on TCO substrates. Moreover, the film shows high structural stability and can generate a stable photocurrent even after being bent hundreds of times.

Metal-Organic Framework for Hypoxia/ROS/pH Triple-Responsive Cargo Release.

Nanoparticulate antitumor photodynamic therapy (PDT) is suffering from a very short lifetime, limited diffusion distance of reactive oxygen species (ROS). Herein, a hypoxia/ROS/pH triple-responsive metal-organic framework (MOF) is designed to facilitate the on-demand release of photosensitizers and hence enhanced PDT efficacy. Tailored azo-containing imidazole ligand is coordinated with zinc to form MOF where photosensitizer (Chlorin e6/Ce6) is encapsulated. Azo can be reduced by overexpressed azoreductase in hypoxic tumor cells, resulting in depletion of glutathione (GSH) and thioredoxin (Trx) which are major antioxidants against ROS oxidative damage in PDT, resulting in rapid cargo release and additional efficacy amplification. The imidazole ionization causes a proton sponge effect to ensure the disintegration of the nanocarriers in acidic organelles, allowing the rapid release of Ce6 through lysosome escape. Under light irradiation, ROS produced by Ce6 may oxidize imidazole to urea, resulting in rapid cargo release. All of the triggers are expected to show interactive synergism. The pH- and hypoxia-responsiveness can improve the release rate of Ce6 for enhanced PDT therapy, whereas the consumption of oxygen by PDT may induce elevated hypoxia and hence in turn enhanced cargo release. This work highlights the role of triple-responsive nanocarriers for triggered photosensitizer release and improved antitumor PDT efficacy.

Microwave- and nitronium ion-enabled rapid and direct production of highly conductive low-oxygen graphene.

Currently the preferred method for large-scale production of solution-processable graphene is via a nonconductive graphene oxide (GO) pathway, which uncontrollably cuts sheets into small pieces and/or introduces nanometer-sized holes in the basal plane. These structural changes significantly decrease some of graphene's remarkable electrical and mechanical properties. Here, we report an unprecedented fast and scalable approach to avoid these problems and directly produce large, highly conductive graphene sheets. This approach intentionally excludes KMnO(4) from Hummers' methods and exploits aromatic oxidation by nitronium ions combined with the unique properties of microwave heating. This combination promotes rapid and simultaneous oxidation of multiple non-neighboring carbon atoms across an entire graphene sheet, thereby producing only a minimum concentration of oxygen moieties sufficient to enable the separation of graphene sheets. Thus, separated graphene sheets, which are referred to as microwave-enabled low-oxygen graphene, are thermally stable and highly conductive without requiring further reduction. Even in the absence of polymeric or surfactant stabilizers, concentrated dispersions of graphene with clean and well-separated graphene sheets can be obtained in both aqueous and organic solvents. This rapid and scalable approach produces high-quality graphene sheets of low oxygen content, enabling a broad spectrum of applications via low-cost solution processing.

Electrocatalytic CO2 Reduction by Molecular Ruthenium Complexes with Polypyridyl Ligands.

Two series of ruthenium complexes with various polypyridyl ligands have been prepared. One series of complexes (5 examples) are featured with tetradentate polypyridyl ligands and two acetonitrile molecules at the axial positions of the coordination sphere; the other series (3 examples) include combinations of a tridentate polypyridyl ligand, one 2,2'-bipyridine (bpy) or two picolines, and one acetonitrile ligand. All these complexes were fully characterized by their NMR spectra as well as X-ray single crystal structures. Their electronic absorption and redox data were measured and reported. Of the 8 complexes, three candidates effectively catalyze electrochemical CO2 reduction reaction (CO2 RR) in wet acetonitrile medium, generating CO as the major product. All these three catalytically active complexes contain a 2,2':6',2'':6'',2'''-quaterpyridine (qpy) ligand scaffold. A maximum turnover frequency (TOFmax ) of>1000 s-1 was achieved for the electrocatalytic CO2 reduction at a modest overpotential. On the basis of electrochemical and spectroelectrochemical evidences, the CO2 substrate was proposed to bind with the ruthenium center at the two-electron reduced state of the complex and then entered the catalytic cycle.

Adjusted degradation of BRD4 S and BRD4 L based on fine structural modifications of the pyrrolopyridone scaffold.

Novel pyrrolopyridone BET degraders were designed and synthesized based on the binding mode between the pyrrolopyridone BET inhibitor with the BRD4 protein. The potent degraders on MV-4-11 cells were discovered through structure-activity relationship study. Modification of warhead on pyrrolopyridone BET degraders significantly regulates BRD4 isoform (long and short) protein degradation, which induces differential cell cycle arrest and apoptosis on MV-4-11 cells. Docking study revealed that the fine structural modification of BET degraders may bind with the BD domain of BRD4 protein to engage various surface areas that bind with CRBN.

A core-shell strategy for constructing a single-molecule junction.

Understanding the effects of intermolecular interactions on the charge-transport properties of metal/molecule/metal junctions is an important step towards using individual molecules as building blocks for electronic devices. This work reports a systematic electron-transport investigation on a series of "core-shell"-structured oligo(phenylene ethynylene) (Gn-OPE) molecular wires. By using dendrimers of different generations as insulating "shells", the intermolecular π-π interactions between the OPE "cores" can be precisely controlled in single-component monolayers. Three techniques are used to evaluate the electron-transport properties of the Au/Gn-OPE/Au molecular junctions, including crossed-wire junction, scanning tunneling spectroscopy (STS), and scanning tunneling microscope (STM) break-junction techniques. The STM break-junction measurement reveals that the electron-transport pathways are strongly affected by the size of the side groups. When the side groups are small, electron transport could occur through three pathways, including through single-molecule junctions, double-molecule junctions, and molecular bridges between adjacent molecules formed by aromatic π-π coupling. The dendrimer shells effectively prohibit the π-π coupling effect, but at the same time, very large dendrimer side groups may hinder the formation of Au-S bonds. A first-generation dendrimer acts as an optimal shell that only allows electron transport through the single-molecule junction pathway, and forbids the other undesired pathways. It is demonstrated that the dendrimer-based core-shell strategy allows the single-molecule conductance to be probed in a homogenous monolayer without the influence of intermolecular π-π interactions.

PI3K/Akt/FoxO pathway mediates glycolytic metabolism in HepG2 cells exposed to triclosan (TCS).

Triclosan (TCS) has been widely used as an antibacterial agent for the last several decades in personal care products. The toxicological effect of TCS has attracted more and more attention of researchers. The purpose of this study is to evaluate the cytotoxic effects of TCS in HepG2 cells and to elucidate the molecular mechanism focusing on regulation of the phosphatidylinositol 3-kinase (PI3K)/protein kinase B (Akt)/forkhead box O (FoxO) pathway in the glycolytic metabolism. In this study, we evaluated the adverse effect of TCS exposure on cell viability, reactive oxygen species (ROS) generation, superoxide dismutase (SOD) activity and mitochondrial membrane potential (MMP). In addition, the glycolysis process in HepG2 cells exposed to TCS was examined in terms of glucose consumption, lactate production and ATP generation. Furthermore, Affymetrix Human U133 plus 2.0 gene chips and gene function enrichment analysis were conducted to screen differential expression genes (DEGs) and potential signaling pathway. Expressions of the glycolysis-related proteins were measured and quantified with Western Blotting. The results showed that TCS could suppress the cell viability, induce oxidative stress, and cause mitochondrial damage. In addition, TCS exposure promoted the glycolysis process, as manifested by accelerated conversion of glucose to lactate and increased energy release. Western Blotting results confirmed that the expression levels of glycolysis related proteins were significantly elevated. The PI3K/Akt/FoxO pathway was identified to play a pivot role in TCS-induced glycolysis, which was further confirmed by inhibitor tests using specific inhibitors LY294002 and MK2206. In general, TCS can induce oxidative stress, cause oxidative damages and promote glycolysis in HepG2 cells, which was mediated by the PI3K/Akt/FoxO pathway.