[Injury of the profunda femoris artery with bleeding requiring transfusion due to secondary dislocation of the lesser trochanter after osteosynthesis of an intertrochanteric femoral fracture]. / Verletzung der A. profunda femoris mit transfusionspflichtiger Blutung durch sekundäre Dislokation des Trochanter minor nach Osteosynthese einer pertrochantären Femurfraktur.

A 95-year-old patient suffered bleeding that required a transfusion after closed reduction and internal fixation (CRIF) of an intertrochanteric femoral fracture with a proximal femoral nail. After mobilization of the patient the secondarily dislocated fragment of the lesser trochanter perforated a side branch of the profunda femoris artery. The bleeding could be stopped by embolization and a few days later the patient could be discharged with stable hemoglobin levels. A continuing decrease of hemoglobin levels despite repeated transfusion of red blood cells is indicative of active bleeding. Accurate identification of the source of the bleeding after osteosynthesis of proximal femoral fractures is decisive for the correct treatment.

Metabolic stability of cells for extended metabolomical measurements using NMR. A comparison between lysed and additionally heat inactivated cells.

NMR measurements for metabolic characterization of biological samples like cells, biopsies or plasma, may take several hours for advanced methods. Preanalytical issues, such as sample preparation and stability over the measurement time, may have a high impact on metabolite content, and potentially lead to misinterpretation. The aim of this study was therefore to investigate by 1H HR-MAS NMR the impact of different cell handling preparation protocols on the stability of the cell metabolite content over the measurement time. For this purpose, the metabolite content of fibroblasts and adrenal cells were measured at different time points after lysis and after additional heating. Interestingly the results showed similar metabolite concentrations between lysed and lysed-heated cells at the beginning of the measurement, but increasing differences after some hours of measurement. In lysed cells, metabolism was ongoing, producing metabolite changes over time, contrary to a stable metabolite content of the lysed-heated cells. These results were confirmed in both fibroblasts and adrenal cells. Therefore, in order to minimize metabolite content modifications over the measurement time, it is suggested to use cell lysis in combination with heat inactivation for extended HR-MAS NMR measurements.

Determination of orthotropic bone elastic constants using FEA and modal analysis.

Finite element models have been widely employed in an effort to quantify the stress and strain distribution around implanted prostheses and to explore the influence of these distributions on their long-term stability. In order to provide meaningful predictions, such models must contain an appropriate reflection of mechanical properties. Detailed geometrical and density information is now readily available from CT scanning. However, despite the use of phantoms, a method of determining mechanical properties (or elastic constants) from bone density has yet to be made available in a usable form. In this study, a cadaveric bone was CT scanned and its natural frequencies were measured using modal analysis. Using the geometry obtained from the CT scan data, a finite element mesh was created with the distribution of density established by matching the mass of the FE bone model with the mass of the cadaveric bone. The maximum values of the orthotropic elastic constants were then established by matching the predictions from FE modal analyses to the experimental natural frequencies, giving a maximum error of 7.8% over 4 modes of vibration. Finally, the elastic constants of the bone derived from the analyses were compared with those measured using ultrasound techniques. This produced a difference of <1% for both the maximum density and axial Young's Modulus. This study has thereby produced an orthotropic finite element model of a human femur. More importantly, however, is the implication that it is possible to create a valid FE model by simply comparing the FE results with the measured resonant frequency of the CT scanned bone.

Bone remodelling of a proximal femur with the thrust plate prosthesis: an in vitro case.

The key to the development of a successful implant is an understanding of the effect of bone remodelling on its long-term fixation. In this study, clinically observed patterns of bone remodelling have been compared with computer-based predictions for one particular design of prosthesis, the Thrust Plate Prosthesis (Centerpulse Orthopedics, Winterthur, Switzerland). Three-dimensional finite-element models were created using geometrical and bone density data obtained from CT scanning. Results from the bone remodelling simulation indicated that varying the relative rate of bone deposition/resorption and the interfacial conditions between the bone and the implant could produce the trend towards the two clinically observed patterns of remodelling.

Investigating the effect of remodelling signal type on the finite element based predictions of bone remodelling around the thrust plate prosthesis: a patient-specific comparison.

The resorption of bone in the human femur following total hip arthroplasty is recognized to be related to the loading in the bone surrounding the prosthesis. However, the precise nature of the mechanical signal that influences the biological remodelling activity of the bone is not completely understood. In this study, a validated finite element modelling methodology was combined with a numerical algorithm to simulate the biological changes over time. This was used to produce bone remodelling predictions for an implanted thrust plate prosthesis (Centerpulse Orthopedics Limited) in a patient specific bone model. The analysis was then repeated using different mechanical signals to drive the remodelling algorithm. The results of these simulations were then compared to the patient-specific clinical data, to distinguish which of the candidate signals produced predictions consistent with the clinical evidence. Good agreement was found for a range of strain energy based signals and also deviatoric remodelling signals. The results, however, did not support the use of compressive dilatational strain as a candidate remodelling signal.