Microwave-assisted synthesis of porous and hollow α-Fe2O3/LaFeO3 nanostructures for acetone gas sensing as well as photocatalytic degradation of methylene blue.

To address the urgent issues of hazardous gas detection and the prevention of environmental pollution, various functional materials for gas sensing and catalytic reduction have been studied. Specifically, the p-type perovskite LaFeO3 has been studied widely because of its promising physicochemical properties. However, there remains several problems to develop a controllable synthesis of LaFeO3-based p-n heterojunctions. In this work, α-Fe2O3 was further compounded with LaFeO3 to form a porous and hollow α-Fe2O3/LaFeO3 heterojunction to improve its gas-sensing performance and photocatalytic efficiency via a microwave-assisted hydrothermal method. While evaluated as sensors of acetone gas, the optimized sample exhibits excellent performance, including a high response (48.3), excellent selectivity, good reversibility, fast response, and recovery ability. Furthermore, it is an efficient catalyst for the degradation of methylene blue. This can be attributed to the enhancement effect of its larger specific surface area, fast diffusion, enhanced surface activities, and p-n heterojunction. Additionally, this work provides a rapid and rational synthesis strategy to produce metal oxides with both enhanced gas-sensing performance and improved photocatalytic properties.

Ultrasensitive xylene gas sensor based on flower-like SnO2/Co3O4 nanorods composites prepared by facile two-step synthesis method.

Xylene is a volatile organic compound which is harmful to the human health and requires precise detection. The detection of xylene by an oxide semiconductor gas sensor is an important research direction. In this work, Co3O4 decorated flower-like SnO2 nanorods (SnO2/Co3O4 NRs) were synthesized by a simple and effective two-step method. The SnO2/Co3O4 NRs show high xylene response (R g/R a = 47.8 for 100 ppm) and selectivity at the operating temperature of 280 °C, and exhibit high stability in continuous testing. The resulting SnO2/Co3O4 NRs nanocomposites show superior sensing performance towards xylene in comparison with pure SnO2 nanorods. The remarkable enhancement in the gas-sensing properties of SnO2/Co3O4 NRs are attributed to larger specific surface area and the formation of p-n heterojunction between Co3O4 and SnO2. These results demonstrate that particular nanostructures and synergistic effect of SnO2 and Co3O4 enable gas sensors to selectively detect xylene.

Formaldehyde gas sensor with extremely high response employing cobalt-doped SnO2 ultrafine nanoparticles.

Formaldehyde is a common carcinogen in daily life and harmful to health. The detection of formaldehyde by a metal oxide semiconductor gas sensor is an important research direction. In this work, cobalt-doped SnO2 nanoparticles (Co-SnO2 NPs) with typical zero-dimensional structure were synthesized by a simple hydrothermal method. At the optimal temperature, the selectivity and response of 0.5% Co-doped SnO2 to formaldehyde are excellent (for 30 ppm formaldehyde, R a/R g = 163 437). Furthermore, the actual minimum detectable concentration of 0.5%Co-SnO2 NPs is as low as 40 ppb, which exceeds the requirements for formaldehyde detection in the World Health Organization (WHO) guidelines. The significant improvement of 0.5%Co-SnO2 NPs gas performance can be attributed to the following aspects: firstly, cobalt doping effectively improves the resistance of SnO2 NPs in the air; moreover, doping creates more defects and oxygen vacancies, which is conducive to the adsorption and desorption of gases. In addition, the crystal size of SnO2 NPs is vastly small and has unique physical and chemical properties of zero-dimensional materials. At the same time, compared with other gases tested, formaldehyde has a strong reducibility, so that it can be selectively detected at a lower temperature.

Ag Nanoparticles Sensitized In2O3 Nanograin for the Ultrasensitive HCHO Detection at Room Temperature.

Formaldehyde (HCHO) is the main source of indoor air pollutant. HCHO sensors are therefore of paramount importance for timely detection in daily life. However, existing sensors do not meet the stringent performance targets, while deactivation due to sensing detection at room temperature, for example, at extremely low concentration of formaldehyde (especially lower than 0.08 ppm), is a widely unsolved problem. Herein, we present the Ag nanoparticles (Ag NPs) sensitized dispersed In2O3 nanograin via a low-fabrication-cost hydrothermal strategy, where the Ag NPs reduces the apparent activation energy for HCHO transporting into and out of the In2O3 nanoparticles, while low concentrations detection at low working temperature is realized. The pristine In2O3 exhibits a sluggish response (Ra/Rg = 4.14 to 10 ppm) with incomplete recovery to HCHO gas. After Ag functionalization, the 5%Ag-In2O3 sensor shows a dramatically enhanced response (135) with a short response time (102 s) and recovery time (157 s) to 1 ppm HCHO gas at 30 °C, which benefits from the Ag NPs that electronically and chemically sensitize the crystal In2O3 nanograin, greatly enhancing the selectivity and sensitivity.

Design of ultrasensitive Ag-LaFeO3 methanol gas sensor based on quasi molecular imprinting technology.

An ultrasensitive methanol gas sensing device based on the quasi-molecular imprinting technology (quasi-MIT) is studied in this work. We applied the sol-gel method (ALS denotes Ag-LaFeO3 prepared by the sol-gel method) and combustion synthesis (ALC denotes Ag-LaFeO3 prepared by combustion synthesis) to prepare Ag-LaFeO3 based sensors. The morphologies and structures of the Ag-LaFeO3 materials were examined via various detection techniques. The ALSM and ALCM sensor (ALSM and ALCM denotes the devices prepared by coating the ALS and ALC materials with methanol, respectively) fabricated using the sol-gel method and combustion synthesis combined with quasi-MIT exhibit good gas sensing properties to methanol, in contrast with the two devices (ALSW and ALCW denote the devices prepared for coating the ALS and ALC materials with water, respectively) without the use of quasi-MIT. The results show that quasi-MIT introduced the target gas in the fabrication process of the device, playing an important role in the design of the ultrasensitive methanol gas sensor. The sensing response and the optimum working temperature of ALSM and ALCM gas sensor are 52.29 and 155 °C and 34.89 and 155 °C, respectively, for 5 ppm methanol, and the highest response to other gases is 8. The ALSM and ALCM gas sensors reveal good selectivity and response for methanol.