Microstructure and corrosion behavior of laser surface-treated AZ31B Mg bio-implant material.

Although magnesium and magnesium alloys are considered biocompatible and biodegradable, they suffer from poor corrosion performance in the human body environment. In light of this, surface modification via rapid surface melting of AZ31B Mg alloy using a continuous-wave Nd:YAG laser was conducted. Laser processing was performed with laser energy ranging from 1.06 to 3.18 J/mm2. The corrosion behavior in simulated body fluid of laser surface-treated and untreated AZ31B Mg alloy samples was evaluated using electrochemical technique. The effect of laser surface treatment on phase and microstructure evolution was evaluated using X-ray diffraction and scanning electron microscopy. Microstructure examination revealed grain refinement as well as formation and uniform distribution of Mg17Al12 phase along the grain boundary for laser surface-treated samples. Evolution of such unique microstructure during laser surface treatment indicated enhancement in the corrosion resistance of laser surface-treated samples compared to untreated alloy.

A multi modal approach to microstructure evolution and mechanical response of additive friction stir deposited AZ31B Mg alloy.

Current work explored solid-state additive manufacturing of AZ31B-Mg alloy using additive friction stir deposition. Samples with relative densities ≥ 99.4% were additively produced. Spatial and temporal evolution of temperature during additive friction stir deposition was predicted using multi-layer computational process model. Microstructural evolution in the additively fabricated samples was examined using electron back scatter diffraction and high-resolution transmission electron microscopy. Mechanical properties of the additive samples were evaluated by non-destructive effective bulk modulus elastography and destructive uni-axial tensile testing. Additively produced samples experienced evolution of predominantly basal texture on the top surface and a marginal increase in the grain size compared to feed stock. Transmission electron microscopy shed light on fine scale precipitation of Mg[Formula: see text]Al[Formula: see text] within feed stock and additive samples. The fraction of Mg[Formula: see text]Al[Formula: see text] reduced in the additively produced samples compared to feed stock. The bulk dynamic modulus of the additive samples was slightly lower than the feed stock. There was a [Formula: see text] 30 MPa reduction in 0.2% proof stress and a 10-30 MPa reduction in ultimate tensile strength for the additively produced samples compared to feed stock. The elongation of the additive samples was 4-10% lower than feed stock. Such a property response for additive friction stir deposited AZ31B-Mg alloy was realized through distinct thermokinetics driven multi-scale microstructure evolution.

Crystallographic texture dependent bulk anisotropic elastic response of additively manufactured Ti6Al4V.

Rapid thermokinetics associated with laser-based additive manufacturing produces strong bulk crystallographic texture in the printed component. The present study identifies such a bulk texture effect on elastic anisotropy in laser powder bed fused Ti6Al4V by employing an effective bulk modulus elastography technique coupled with ultrasound shear wave velocity measurement at a frequency of 20 MHz inside the material. The combined technique identified significant attenuation of shear velocity from 3322 ± 20.12 to 3240 ± 21.01 m/s at 45[Formula: see text] and 90[Formula: see text] orientations of shear wave plane with respect to the build plane of printed block of Ti6Al4V. Correspondingly, the reduction in shear modulus from 48.46 ± 0.82 to 46.40 ± 0.88 GPa was obtained at these orientations. Such attenuation is rationalized based on the orientations of [Formula: see text] crystallographic variants within prior columnar [Formula: see text] grains in additively manufactured Ti6Al4V.

Computational Assessment of Thermokinetics and Associated Microstructural Evolution in Laser Powder Bed Fusion Manufacturing of Ti6Al4V Alloy.

Although most of the near non-equilibrium microstructures of alloys produced by laser powder bed fusion (LPBF) additive manufacturing (AM) are being reported at a rapid rate, the accountable thermokinetics of the entire process have rarely been studied. In order to exploit the versatility of this AM process for the desired properties of built material, it is crucial to understand the thermokinetics associated with the process. In light of this, a three-dimensional thermokinetic model based on the finite element method was developed to correlate with the microstructure evolved in additively manufactured Ti6Al4V alloy. The computational model yielded the thermal patterns experienced at given location while building a single layer through multiple laser scans and a whole part through multiple layers above it. X-ray analysis of the resultant microstructure confirmed the presence of acicular martensitic (α') phase of (002) texture within the build-plane. Computationally predicted magnitude of the thermal gradients within the additively manufactured Ti6Al4V alloy in different directions (X, Y, and Z) facilitated the understanding about the evolution of grain morphology and orientation of acicular martensite in prior ß grains. The scanning electron microscopy observations of the alloy revealed the distinct morphology of phase precipitated within the martensitic phase, whose existence was, in turn, understood through predicted thermal history.

In-vitro bio-corrosion behavior of friction stir additively manufactured AZ31B magnesium alloy-hydroxyapatite composites.

Magnesium and its alloys have been considered for consumable bio-implant applications due to their similar mechanical properties to the natural bone and biodegradability. Nevertheless, uncontrollable corrosion rate and limited bioactivity of Mg based materials in biological environment restrain their application. In light of this, objective of the present study was to explore addition of hydroxyapatite (HA, Ca10(PO4)6OH2), a ceramic similar to bone mineral, into AZ31B Mg alloy and its effects on bio-corrosion behavior. Friction stir processing based additive manufacturing route was employed for producing AZ31B Mg-HA composites. Various HA contents (5, 10, and 20 wt%) were incorporated into Mg matrix. The microstructural observation revealed that the size of α-Mg grains reduced significantly after friction stir process. HA incorporation took place at micro/nanoscale in α-Mg matrix under the thermo-mechanical forces exerted by friction stir process. The corrosion behavior of friction stir processed Mg-HA composites was investigated using electrochemical methods in simulated body fluid. The results indicated an improvement in corrosion resistance for the composites compared to untreated AZ31B which was attributed to significant grain refinement upon friction stir process. On the other hand, incremental addition of HA had an opposing effect due to localized micro/nano-galvanic couples. As a result, friction stir process Mg-5 wt% HA composite demonstrated the highest corrosion resistance due to an optimum balance between beneficial effects of grain size refinement and limited number of local galvanic couples compared to the other friction stir process samples explored in the present work.

In-vitro biomineralization and biocompatibility of friction stir additively manufactured AZ31B magnesium alloy-hydroxyapatite composites.

The present study aims to evaluate effect of hydroxyapatite (HA, Ca10(PO4)6OH2), a ceramic similar to natural bone, into AZ31B Mg alloy matrix on biomineralization and biocompatibility. The novel friction stir processing additive manufacturing route was employed to fabricate Mg-HA composites. Various HA contents (5, 10, 20 wt%) were incorporated into Mg matrix. Microstructural observation and chemical composition analysis revealed that refined Mg grains and dispersion of HA particles at micro/nanoscales were achieved in Mg-HA composites after the friction stir processing. The biomineralization evaluation were carried out using immersion experiments in simulated body fluid followed by mineral morphology observation and chemical composition analysis. The wettability measurements were conducted to correlate the biomineralization behavior. The results showed improvement in wettability and bone-like Ca/P ratio in apatite deposit on the composites compared to as-received Mg. In addition, the increase of blood compatibility, cell viability and spreading were found in the higher HA content composites, indicating the improved biocompatibility. Therefore, friction stir processed Mg-20 wt%HA composite exhibited the highest wettability and better cell adhesion among other composites due to the effect of increased HA content within Mg matrix.

Optimization of biocompatibility in a laser surface treated Mg-AZ31B alloy.

Biodegradable bone implants can remove the need for subsequent bone-implant surgeries by controlled biomineralization and degradation. Although Mg-alloys generally possess biocompatible properties, they corrode rapidly, thereby preventing sufficient hydroxyapatite formation and biomineral growth. In an attempt to address these limitations, laser surface treatments were performed via the employment of a continuous wave Nd:YAG laser on the Mg-AZ31B alloy using laser fluences in the range of 1.06-4.24 J/mm2 (250-1000 W). The laser-treated samples were investigated for their wettability in simulated body fluid. In vitro analyses were performed in simulated body fluid to examine corrosion and biomineralization behavior on the laser-treated samples. Statistical optimization algorithms based on wettability data predicted an optimal laser fluence of 3.286J/mm2 (775 W) within the range of laser fluences used in the present study for achieving a balance between biodegradation and biomineralization. Confirmatory tests on optimized samples indicated an up to 84% grain size reduction in laser-treated surface regions, a several-fold increase in Mg17Al12 (ß) phase volume fraction, a reasonably abundant formation of hydroxyapatite, and increased rates of biomineralization that exceeded degradation. These findings indicate the potential of laser surface engineering to realize Mg-AZ31B alloy as a viable biodegradable bone implant material.

Integrated experimental and computational approach to laser machining of structural bone.

This study describes the fundamentals of laser-bone interaction during bone machining through an integrated experimental-computational approach. Two groups of laser machining parameters identified the effects of process thermodynamics and kinetics on machining attributes at micro to macro. A continuous wave Yb-fiber Nd:YAG laser (wavelength 1070 nm) with fluences in the range of 3.18 J/mm2-8.48 J/mm2 in combination of laser power (300 W-700 W) and machining speed (110 mm/s-250 mm/s) were considered for machining trials. The machining attributes were evaluated through scanning electron microscopy observations and compared with finite element based multiphysics-multicomponent computational model predicted values. For both groups of laser machining parameters, experimentally evaluated and computationally predicted depths and widths increased with increased laser energy input and computationally predicted widths remained higher than experimentally measured widths whereas computationally predicted depths were slightly higher than experimentally measured depths and reversed this trend for the laser fluence >6 J/mm2. While in both groups, the machining rate increased with increased laser fluence, experimentally derived machining rate remained lower than the computationally predicted values for the laser fluences lower than ∼4.75 J/mm2 for one group and ∼5.8 J/mm2 for other group and reversed in this trend thereafter. The integrated experimental-computational approach identified the physical processes affecting machining attributes.