High performance CNT point emitter with graphene interfacial layer.

Carbon nanotubes (CNTs) have great potential in the development of high-power electron beam sources. However, for such a high-performance electronic device, the electric and thermal contact problem between the metal and CNTs must be improved. Here, we report graphene as an interfacial layer between the metal and CNTs to improve the interfacial contact. The interfacial graphene layer results in a dramatic decrease of the electrical contact resistance by an order of 2 and an increase of the interfacial thermal conductivity by 16%. Such a high improvement in the electrical and thermal interface leads to superior field emission performance with a very low turn-on field of 1.49 V µm(-1) at 10 µA cm(-2) and a threshold field of 2.00 V µm(-1) at 10 mA cm(-2), as well as the maximum current of 16 mA (current density of 2300 A cm(-2)).

Superior rechargeability and efficiency of lithium-oxygen batteries: hierarchical air electrode architecture combined with a soluble catalyst.

The lithium-oxygen battery has the potential to deliver extremely high energy densities; however, the practical use of Li-O2 batteries has been restricted because of their poor cyclability and low energy efficiency. In this work, we report a novel Li-O2 battery with high reversibility and good energy efficiency using a soluble catalyst combined with a hierarchical nanoporous air electrode. Through the porous three-dimensional network of the air electrode, not only lithium ions and oxygen but also soluble catalysts can be rapidly transported, enabling ultra-efficient electrode reactions and significantly enhanced catalytic activity. The novel Li-O2 battery, combining an ideal air electrode and a soluble catalyst, can deliver a high reversible capacity (1000 mAh g(-1) ) up to 900 cycles with reduced polarization (about 0.25 V).

Twistable and bendable actuator: a CNT/polymer sandwich structure driven by thermal gradient.

We demonstrate a novel configuration of an electrothermal actuator (ETA), which is based on a polydimethylsiloxane (PDMS) slab sandwiched by upper and lower active layers of CNT-PDMS composite. When only one active layer of a single sandwich structure ETA is heated and the other is not, there exists a thermal gradient in the direction of the slab thickness, resulting in bending motion toward the unheated side. Moreover, a dual sandwich structure ETA, consisting of two parallel assembled sandwich structures on the same body, has the unique ability to act with a twisting motion as the two ETAs bend in opposite directions. We expect the advent of the bendable and twistable actuator to break new ground in ETAs.

Fibers of reduced graphene oxide nanoribbons.

Reduced graphene oxide nanoribbon fibers were fabricated by using an electrophoretic self-assembly method without the use of any polymer or surfactant. We report electrical and field emission properties of the fibers as a function of reduction degree. In particular, the thermally annealed fiber showed superior field emission performance with a low potential for field emission (0.7 V µm(-1)) and a giant field emission current density (400 A cm(-2)). Moreover, the fiber maintains a high current level of 300 A cm(-2) corresponding to 1 mA during long-term operation.

A reel-wound carbon nanotube polarizer for terahertz frequencies.

Utilizing highly oriented multiwalled carbon nanotube aerogel sheets, we fabricated micrometer-thick freestanding carbon nanotube (CNT) polarizers. Simple winding of nanotube sheets on a U-shaped polyethylene reel enabled rapid and reliable polarizer fabrication, bypassing lithography or chemical etching processes. With the remarkable extinction ratio reaching ∼37 dB in the broad spectral range from 0.1 to 2.0 THz, combined with the extraordinary gravimetric mechanical strength of CNTs, and the dispersionless character of freestanding sheets, the commercialization prospects for our CNT terahertz polarizers appear attractive.

High-permeability vacuum membrane distillation utilizing mechanically compressed carbon nanotube membranes.

Membranes for membrane distillation (MD) are mostly made of polymeric and ceramic materials. We demonstrate here that the laterally-compressed, vertically-aligned CNTs (VACNT) obtainable from a CNT forest are an excellent membrane material for vacuum membrane distillation (VMD). The VACNT structure provides interstices between CNTs for extracting vaporized water molecules, while efficiently filtering the impurity salts. The VACNT membrane is shown to deliver excellent performance when tested for the desalination of 3.5 wt% NaCl water solution, as exemplified by the permeability of 68 LMH (liter per square meter per hour) achieved at the salt rejection of over 99.8% at 65 °C. We also demonstrate that the VACNT membrane performance can be maintained with time with the aid of a simple cleaning procedure, which bodes well for a long lifetime of the membrane for VMD application.

Crystal-like growth of a metal oxide/CNT composite fiber with electroplated "seed" from a CNT-dispersed nonaqueous electrolyte.

A fabrication technique is developed for the preparation of metal oxide/CNT composites. An essential feature of the technique lies in the use of nonaqueous electrolyte in place of the usual aqueous electrolyte, which ensures well-dispersed CNTs without surfactants. After a "seed" is formed by electroplating on the anode, the seed is simply pulled up at a certain speed to grow a 1D CNT composite structure. The technique leads to a uniform distribution of metal oxide and a high weight fraction of CNT in the composite structure. Moreover, the conductivity of the composite is much higher than that of the CNT fibers fabricated with polymer.

H(2) sensing characteristics of SnO(2) coated single wall carbon nanotube network sensors.

SnO(2) nanoparticle coated single wall nanotube (SWNT) network sensors were fabricated by forming a SWNT network on the Pt patterned SiO(2)/Si substrate using a dip coating method and subsequently depositing SnO(2) nanoparticles on the SWNT network by rf magnetron sputtering. Their H(2) gas sensing properties were investigated. The SnO(2)-SWNT network sensors stably and reversibly responded to H(2) gas even at room temperature and could detect H(2) gas down to 100 ppm. In addition to the low temperature detection, a remarkable finding was that the gas sensing behavior of SnO(2)-SWNT network sensors was changed from p-type to n-type with increasing SnO(2) deposition time (i.e. surface coverage of SnO(2) on SWNT). A schematic model was proposed to explain the switching of sensing behavior depending on the surface coverage of SnO(2) nanoparticles on the SWNTs.

Reduced graphene-oxide filter system for removing filterable and condensable particulate matter from source.

Air pollution is one of the most serious problems facing mankind because of its impact on ecosystems and human beings. Although particulate matter (PM) consists of both filterable PM (FPM) and condensable PM (CPM), most research has focused on eliminating only FPM. In this work, we introduce a filter system that removes both FPM and CPM from pollution source with high efficiency. The system consists of two reduced graphene oxide (rGO) filters and a condenser between them that can remove the usual FPM and at the same time CPM-induced FPM that typically leaves the pollution source unabated. The filters, quite effective in removing the PM with their three-dimensional structure, retain the removal capability even at high temperature and in acidic condition that prevail at the pollution source. The proposed rGO system could provide a complete solution for removal of both FPM and CPM from the pollution source.

Macroscopic single-walled-carbon-nanotube fiber self-assembled by dip-coating method.

Pure macroscopic single-walled-carbon-nanotube (SWNT) fibers are fabricated by using a dip-coating method without any additive or additional electrical equipment or complex apparatus. The present method only utilizes microfluidics, which includes capillary condensation, capillary flow, and surface tension, and results in the self-assembly and self-alignment of SWNT colloids.

Synthesis of a Carbonaceous Two-Dimensional Material.

Despite tremendous accomplishments achieved in 2D materials, little progress has been made in carbonaceous 2D materials beyond graphene and graphene oxide. Here, we report a 2D material of carbonaceous nanoplates (CANP). The bottom-up synthesis of CANP is green, separation-free, and massive. The nanoplates are 2 to 3 monolayers thick with an average interlayer spacing of 0.57 nm. The synthesis involves viscosity-aided two-dimensional growth of fragmented glucose derivatives and leads to the complete conversion of glucose to the 2D nanoplates. Application tests demonstrate the usefulness of the affordable 2D material.

Single-walled carbon-nanotube networks on large-area glass substrate by the dip-coating method.

Highly uniform and large-area single-walled carbon-nanotube (SWNT) networks are realized by the dip-coating method, which is based on fundamental fluid-dynamic phenomena such as capillary condensation and surface tension. The changes in the polarity and hydration properties of the substrate affect the morphology of the SWNT networks and result in nonlinear growth of the networks in the repetitive dip-coating process. The density and the thickness of the SWNT networks are controlled by processing variables including number of dip coatings, concentration of SWNT colloidal solution, and withdrawal velocity. The networks have uniform sheet resistances and high optical transmittance in the visible wavelength range.

High-Performance Field Emission from a Carbonized Cork.

To broaden the range of application of electron beams, low-power field emitters are needed that are miniature and light. Here, we introduce carbonized cork as a material for field emitters. The light natural cork becomes a graphitic honeycomb upon carbonization, with the honeycomb cell walls 100-200 nm thick and the aspect ratio larger than 100, providing an ideal structure for the field electron emission. Compared to nanocarbon field emitters, the cork emitter produces a high current density and long-term stability with a low turn-on field. The nature of the cork material makes it quite simple to fabricate the emitter. Furthermore, any desired shape of the emitter tailored for the final application can easily be prepared for point, line, or planar emission.

High Power Density Electrochemical Thermocells for Inexpensively Harvesting Low-Grade Thermal Energy.

Continuously operating thermo-electrochemical cells (thermocells) are of interest for harvesting low-grade waste thermal energy because of their potentially low cost compared with conventional thermoelectrics. Pt-free thermocells devised here provide an output power of 12 W m-2 for an interelectrode temperature difference (ΔT) of 81 °C, which is sixfold higher power than previously reported for planar thermocells operating at ambient pressure.

Flow-less and shape-conformable CNT sheet nanogenerator for self-powered motion sensor.

A carbon nanotube (CNT) sheet nanogenerator that does not require any liquid or gas flow for power generation is developed on the basis of Coulombic interactions, making the device attractive as a building block for self-powered sensors. The working principle of the CNT nanogenerator is probed in terms of sweeping speed, distance between charged object and nanotube sheet, surface charge, and number of layers of nanotube sheet. The nature of the CNT sheet and its formation process is such that simply winding the CNT sheet stripe n times around a substrate leads to increasing the power n times. For a practical demonstration of the CNT nanogenerator, a self-powered sensor array screen is developed that can read finger movements, just as with a finger command on a smartphone screen.

Autonomous Graphene Vessel for Suctioning and Storing Liquid Body of Spilled Oil.

Despite remarkable strides in science and technology, the strategy for spilled oil collection has remained almost the same since the 1969 Santa Barbara oil spill. The graphene vessel devised here can bring about an important yet basic change in the strategy for spilled oil collection. When it is placed on the oil-covered seawater, the graphene vessel selectively separates the oil, then collects and stores the collected oil in the vessel all by itself without any external power inputs. Capillarity and gravity work together to fill this proto-type graphene vessel with the spilled oil at a rate that is higher than 20,000 liters per square meter per hour (LMH) with oil purity better than 99.9%, and allow the vessel to withstand a water head of 0.5 m. The vessel also has a superb chemical stability and recyclability. An expanded oil contact area, considerably greater than the thickness of the oil layer, forms at the reduced graphene oxide (rGO) foam interface upon contact with the spilled oil. This expanded contact area does not change much even when the oil layer thins out. As a result, the high oil collection rate is maintained throughout the recovery of spilled oil.

Membrane of Functionalized Reduced Graphene Oxide Nanoplates with Angstrom-Level Channels.

Membranes with atomic level pores or constrictions are valuable for separation and catalysis. We report a graphene-based membrane with an interlayer spacing of 3.7 angstrom (Å). When graphene oxide nanoplates are functionalized and then reduced, the laminated reduced graphene oxide (rGO) nanoplates or functionalized rGO membrane is little affected by an intercalated fluid, and the interlayer spacing of 3.7 Å increases only to 4.4 Å in wetted state, in contrast to the graphene oxide (GO) membrane whose interlayer spacing increases from 9 Å to 13 Å in wetted state. When applied to ion separation, this membrane reduced the permeation rate of small ions such as K(+) and Na(+) by three orders of magnitude compared to the GO membrane.

High-efficiency electrochemical thermal energy harvester using carbon nanotube aerogel sheet electrodes.

Conversion of low-grade waste heat into electricity is an important energy harvesting strategy. However, abundant heat from these low-grade thermal streams cannot be harvested readily because of the absence of efficient, inexpensive devices that can convert the waste heat into electricity. Here we fabricate carbon nanotube aerogel-based thermo-electrochemical cells, which are potentially low-cost and relatively high-efficiency materials for this application. When normalized to the cell cross-sectional area, a maximum power output of 6.6 W m(-2) is obtained for a 51 °C inter-electrode temperature difference, with a Carnot-relative efficiency of 3.95%. The importance of electrode purity, engineered porosity and catalytic surfaces in enhancing the thermocell performance is demonstrated.

Three-dimensional analysis of electrode behavior in a human cochlear model.

Three-dimensional (3D) finite element analysis is used in this study to model the mechanical effects of the electrode in a cochlear implant. We employ six electrodes with different stiffness produced by different arrangements of metal wires. Different wire arrangements are generated by changing the fitness function of a genetic program. The human cochlea is modeled by the spiral-approximation method. Reconstructed three-dimensional CT images are used to model the real insertion condition. The contact pressure at the tip and the insertion force are found to be highest when the wires are stacked horizontally. Axial rotation of the electrode has minimal effect on the stimulating current spread. The electrode does not contact the basilar membrane. The results indicate that considering the electrode stiffness is important to minimizing mechanical trauma in cochlear implantation.

Carbon nanotube-bonded graphene hybrid aerogels and their application to water purification.

We present carbon nanotube (CNT)-bonded graphene hybrid aerogels that are prepared by growing CNTs on a graphene aerogel surface with nickel catalyst. The presence of bonded CNTs in the graphene aerogel results in vastly improved mechanical and electrical properties. A significant increase in specific surface area is also realized. The presence of the CNTs transforms the hybrid aerogels into a mesoporous material. The viscoelasticity of the hybrid aerogels is found to be invariant with respect to temperature over a range of between -150 °C and 450 °C. These characteristics along with the improved properties make the hybrid aerogels an entirely different class of material with applications in the fields of biotechnology and electrochemistry. The mesoporous nature of the material along with its high specific surface area also makes the hybrid aerogel attractive for application in water treatment. Both anionic and cationic dyes can be effectively removed from water by the hybrid aerogel. A number of organics and oils can be selectively separated from water by the hybrid aerogel. The hybrid aerogel is easy to handle and separate from water due to its magnetic nature, and can readily be recycled and reused.