Multifunctionality Analysis of Structural Supercapacitors- A Review.

Structural supercapacitors (SSCs) are multifunctional energy storage composites (MESCs) that combine the mechanical properties of fiber-reinforced polymers and the electrochemical performance of supercapacitors to reduce the overall mass in lightweight applications with electrical energy consumption. These novel MESCs have huge potentials, and their properties have improved dramatically since their introduction in the early 2000's. However, the current properties of SSCs are not sufficient for complete energy supply of electrically driven devices. To overcome this drawback, the aim of the current study is to identify key areas for enhancement of the multifunctional performance of SSCs. Critical modification paths for the SSC constituents are systematically analyzed. Special focus is given to the improvement of carbon fiber-based electrodes, the selection of structural electrolytes and the implementation of separators for the development of more efficient SSCs. Finally, current SSCs are compared in terms of their multifunctionality including material combinations and modifications.

Physicochemical Modeling of Electrochemical Impedance in Solid-State Supercapacitors.

Solid-state supercapacitors (SSCs) consist of porous carbon electrodes and gel-polymer electrolytes and are used in novel energy storage applications. The current study aims to simulate the impedance of SSCs using a clearly defined equivalent circuit (EC) model with the ultimate goal of improving their performance. To this end, a conventional mathematical and a physicochemical model were adapted. The impedance was measured by electrochemical impedance spectroscopy (EIS). An EC consisting of electrical elements was introduced for each modeling approach. The mathematical model was purely based on a best-fit method and utilized an EC with intuitive elements. In contrast, the physicochemical model was motivated by advanced theories and allowed meaningful associations with properties at the electrode, the electrolyte, and their interface. The physicochemical model showed a higher approximation ability (relative error of 3.7%) due to the interface impedance integration in a more complex circuit design. However, this model required more modeling and optimization effort. Moreover, the fitted parameters differed from the analytically calculated ones due to uncertainties in the SSC's microscale configuration, which need further investigations. Nevertheless, the results show that the proposed physicochemical model is promising in simulating EIS data of SSCs with the additional advantage of utilizing well-reasoned property-based EC elements.

Determination of a Representative and 3D-Printable Root Canal Geometry for Endodontic Investigations and Pre-Clinical Endodontic Training-An Ex Vivo Study.

Models of artificial root canals are used in several fields of endodontic investigations and pre-clinical endodontic training. They allow the physical testing of dental treatments, the operating of instruments used and the interaction between these instruments and the tissues. Currently, a large number of different artificial root canal models exist whose geometry is created either on the basis of selected natural root canal systems or to represent individual geometrical properties. Currently, only a few geometric properties such as the root canal curvature or the endodontic working width are taken into consideration when generating these models. To improve the representational capability of the artificial root canal models, the aim of the current study is therefore to generate an artificial root canal based on the statistical evaluation of selected natural root canals. Here, the approach introduced by Kucher for determining the geometry of a root canal model is used, which is based on the measurement and statistical evaluation of the root canal center line's curvatures and their cross-sectional dimensions. Using the example of unbranched distal root canals of mandibular molars (n = 29), an artificial root canal model representing the mean length, curvature, torsion and cross-sectional dimensions of these teeth could be derived.

DMA of TPU Films and the Modelling of Their Viscoelastic Properties for Noise Reduction in Jet Engines.

Due to current developments in jet engine design, the acoustic performance of conventional acoustic liners needs to be improved with respect to lower frequency spectrums and broadband absorption. In this context, the present study aimed to determine the viscoelastic material properties of a thermoplastic polyurethane (TPU) film for targeted application in novel acoustic liners with integrated film material for enhanced noise reduction. Therefore, a dynamic mechanical analysis (DMA) was performed to determine these viscoelastic material properties. Based on the acquired data, the time-temperature shift (TTS) was applied to obtain the material's temperature- and frequency-dependent mechanical properties. In this regard, the William-Landel-Ferry (WLF) method and an alternative polynomial approach determining the shift factors were investigated and compared. Furthermore, a generalized Maxwell model-so-called Prony-series-with and without pre-smoothing utilizing of a fractional rheological model was applied to approximate the measured storage and loss modulus and to provide a material model that can be used in finite element analyses. Finally, the results were discussed concerning the application of the films in acoustic liners under the conditions of a standard flight cycle and the applied loads. The present investigations thus provide a method for characterizing polymer materials, approximating their mechanical behavior for vibration applications at different ambient temperatures and enabling the identification of their operational limits during the application in acoustic liners.

An Automated Measurement Method for the Endodontic Working Width of Lower Molars by Means of Parametric Models Using Cone-beam Computed Tomographcy and Micro-Computed Tomography.

INTRODUCTION: A new method for the approximation of the root canal's cross-sectional shape and its working width using cone-beam computed tomographic (CBCT) or micro-computed tomographic (micro-CT) imaging was introduced. METHODS: Scanned data from 29 extracted human mandibular first and second molar distal root canals without instrumentation were reconstructed and analyzed with a self-developed measurement algorithm. The 3-dimensional volume models were sliced perpendicular to the vertical axis. Using different 2-dimensional parametric models, the contour of each root canal slice was approximated and used to determine the canal's cross-sectional dimensions. The measurements of minor width, major width, and the root canal's conicity were statistically analyzed using analysis of variance. RESULTS: The measured minor and major widths of the investigated root canals were significantly higher (probability value P < .05) when evaluated by CBCT images than the results obtained from micro-CT data. Both dimensions increased starting from the apical foramen (P < .01). The narrowest measured canal widths were 0.19-0.24 mm for CBCT imaging and 0.09-0.21 mm for micro-CT imaging in the apical part. The maximum values for conicity were between 13% and 17% in the cervical third. CONCLUSIONS: The 3-dimensional imaging data from CBCT and micro-CT imaging enabled a valuable anatomic assessment of the root canal's cross-sectional working width along the canal up to the physiological foramen in order to determine an adequate apical diameter as well as the correct measured taper in the cervical and medial part.

Mapping of the Micro-Mechanical Properties of Human Root Dentin by Means of Microindentation.

The extensive knowledge of root dentin's mechanical properties is necessary for the prediction of microstructural alterations and the teeth's deformations as well as their fracture behavior. Standardized microindentation tests were applied to apical, medial, and cervical root sections of a mandibular human first molar to determine the spatial distribution of the hard tissue's properties (indentation modulus, indentation hardness, Martens hardness, indentation creep). Using an indentation mapping approach, the inhomogeneity of mechanical properties in longitudinal as well as in transversal directions were measured. As a result, the tooth showed strongly inhomogeneous material properties, which depended on the longitudinal and transversal positions. In the transversal cutting planes of the cervical, medial, apical sections, the properties showed a comparable distribution. A statistical evaluation revealed an indentation modulus between 12.2 GPa and 17.8 GPa, indentation hardness between 0.4 GPa and 0.64 GPa and an indentation creep between 8.6% and 10.7%. The established standardized method is a starting point for further investigations concerning the intensive description of the inhomogeneous mechanical properties of human dentin and other types of dentin.

Continuous Measurement of Three-Dimensional Root Canal Curvature Using Cone-Beam Computed and Micro-Computed Tomography: A Comparative Study.

The knowledge of root canal curvature is crucial regarding the prevention of ledge formation, root perforation and the possibility of endodontic instruments' fracture during endodontic treatments. Therefore, a quantification method of the root canal curvature as well as the applicability of diagnostically relevant tomographic three-dimensional (3D) imaging data is necessary. Hereby, cone-beam computed tomography (CBCT) images and micro-computed tomography (µCT) data of distal root canals were analysed concerning the continuous three-dimensional curvature of human mandibular molars ( n = 50). The curvature of the canal's three-dimensional centre line was determined by evaluating the tomographic images. The centroids of each root canal slice were identified and approximated by spline curves to obtain the centre line and therefore, its curvature. Comparing the results evaluated from CBCT and µCT images, minimum radii of curvature of 2.6 mm and 2.1 mm were determined, respectively. The observation of the centre line demonstrated the requirement of the three-dimensional imaging data from CBCT and µCT for a reliable curvature analysis. Conclusively, the evaluation of CBCT and µCT images results in comparable radii of curvature. Thus, the application of the introduced method in combination with CBCT applied to patient cases could offer an important preliminary diagnostical step to prevent endodontic treatment complications.

Effects of Endodontic Irrigants on Material and Surface Properties of Biocompatible Thermoplastics.

Passive irrigation is an efficient method for a successful endodontic treatment. During sonic activation biocompatible polymer tips are used to activate irrigants. Compared to ultrasonic activation with metallic tips, polymer tips have the advantage of a reduced risk of fracture and minimise dentine damage. Hence, two polymers, polyether ether ketones (PEEK) and polyamide (PA6), were identified for the manufacturing of novel irrigation tips. The chemical resistance against the irrigants ethylenediaminetetraacetic acid (EDTA) 20%, chlorhexidine gluconate (CHX) 2% and sodium hypochlorite (NaOCl) 5.25% was analysed. Using microindentation, the change of hardness, elasticity, surface roughness and appearance of the polymers was determined. PA6 had a high absorption of irrigant compared to PEEK. PEEK was resistant to the investigated irrigants and showed no significant alteration of surface and mechanical properties, whereas PA6 slightly increased its hardness, elastic modulus and surface roughness during long-term exposure at 37 °C. However, PA6 tips seem to be a promising disposable product due to the material's high deformability and low manufacturing costs. Particularly with regard to structural-dynamic properties and high chemical resistance, PEEK can be considered as a material for reusable irrigation tips.

An Approach for a Mathematical Description of Human Root Canals by Means of Elementary Parameters.

INTRODUCTION: Root canal geometry is an important factor for instrumentation and preparation of the canals. Curvature, length, shape, and ramifications need to be evaluated in advance to enhance the success of the treatment. Therefore, the present study aimed to design and realize a method for analyzing the geometric characteristics of human root canals. METHODS: Two extracted human lower molars were radiographed in the occlusal direction using micro-computed tomographic imaging. The 3-dimensional geometry of the root canals, calculated by a self-implemented image evaluation algorithm, was described by 3 different mathematical models: the elliptical model, the 1-circle model, and the 3-circle model. RESULTS: The different applied mathematical models obtained similar geometric properties depending on the parametric model used. Considering more complex root canals, the differences of the results increase because of the different adaptability and the better approximation of the geometry. CONCLUSIONS: With the presented approach, it is possible to estimate and compare the geometry of natural root canals. Therefore, the deviation of the canal can be assessed, which is important for the choice of taper of root canal instruments. Root canals with a nearly elliptical cross section are reasonably approximated by the elliptical model, whereas the 3-circle model obtains a good agreement for curved shapes.