Successful treatment of congenital pseudarthrosis of the tibia: still a challenge.

The congenital pseudarthrosis of the tibia (CPT) is one of the most challenging problems in pediatric orthopedics. The primary treatment goals are outlined as osteosynthesis, stabilization of the ankle mortise by fibular stabilization and lower-limb-length equalization. Despite the fact that each of the aforementioned goals is difficult to be achieved regardless the surgical option, the main biological consideration is the same: pseudarthrosis resection, biological bone bridging of the defect by stable fixation and the correction of any angular deformity. The external fixation method is suggested as valuable treatment of CPT because it can address not only pseudarthrosis but also all complex deformities associated with this condition. However, treatment of CPT is impaired with complications due to the complex nature of the disease thus failure is common. The most common of these are refracture, growth disturbance, poor foot and ankle function with stiffness. Of these, refracture is the most common and serious complication after primary healing and might result in the reestablishment of pseudarthrosis. Therefore, an effective, safe and practical treatment method that minimizes the residual challenges after healing and accomplishes the multiple goals of treatment is needed. In this article, we report a patient with CPT treated successfully with external fixation. Level of evidence IV retrospective.

The anatomy of the ACL and its importance in ACL reconstruction.

The anterior cruciate ligament (ACL) anatomy is very significant if a reconstruction is attempted after its rupture. An anatomic study should have to address, its biomechanical properties, its kinematics, its position and anatomic correlation and its functional properties. In this review, an attempt is made to summarize the most recent and authoritative tendencies as far as the anatomy of the ACL, and its surgical application in its reconstruction are concerned. Also, it is significant to take into account the anatomy as far as the rehabilitation protocol is concerned. Separate placement in the femoral side is known to give better results from transtibial approach. The medial tibial eminence and the intermeniscal ligament may be used as landmarks to guide the correct tunnel placement in anatomic ACL reconstruction. The anatomic centrum of the ACL femoral footprint is 43 % of the proximal-to-distal length of lateral, femoral intercondylar notch wall and femoral socket radius plus 2.5 mm anterior to the posterior articular margin. Some important factors affecting the surgical outcome of ACL reconstruction include graft selection, tunnel placement, initial graft tension, graft fixation, graft tunnel motion and healing. The rehabilitation protocol should come in phases in order to increase range of motion, muscle strength and leg balance, it should protect the graft and weightbearing should come in stages. The cornerstones of such a protocol remain bracing, controlling edema, pain and range of motion. This should be useful and valuable information in achieving full range of motion and stability of the knee postoperatively. In the end, all these advancements will contribute to better patient outcome. Recommendations point toward further experimental work with in vivo and in vitro studies, in order to assist in the development of new surgical procedures that could possibly replicate more closely the natural ACL anatomy and prevent future knee pathology.

Comparative study of internal and hybrid external fixation in tibial condylar fractures.

BACKGROUND: The spectrum of injuries to the tibial plateau is so great that no single method of treatment has been proven to be uniformly successful. The purposes of this study were to evaluate the clinical results, to identify the advantages and disadvantages and to take out useful conclusions of the application of the internal and hybrid external fixation in the treatment of these fractures. METHOD: Sixty tibial condylar fractures, of all types, according to Schatzker's classification were treated with open reduction and internal fixation (30 patients) or with hybrid external fixation (30 patients). The following parameters were recorded: time of surgical procedure, time of postoperative hospitalization, time of starting of weight bearing on the affected extremity, complications, and postoperative functional (according to Knee Society Score) and radiological results (according to Rasmussen's Radiological Score). The average time of follow-up was 12 months. RESULTS: Neither of the two methods showed superiority regarding the duration of the surgical procedure [mean difference 4.4 ± 5.4 (min), P = NS], the postoperative hospitalization time [0.6 ± 0.7 (days), P = NS], and the radiological and functional evaluation (χ(2), P = NS for all comparisons). However, the internal fixation method proved to be superior to the hybrid external fixation regarding the time of starting the weight bearing [3.1 ± 0.4 (weeks), P < 0.001]. CONCLUSION: Internal fixation showed superiority to the time starting of weight bearing as it occurred at an earlier time than that of hybrid external by almost 3 weeks whereas no other differences were identified in the other parameters regarding patients' rehabilitation.

Fixed versus mobile bearing knee arthroplasty: a review of kinematics and results.

There are several total knee arthroplasty designs available with wide variation in features. The long-term results of total knee replacement with a fixed bearing design have shown a high degree of clinical success. However, implant loosening and polyethylene wear became recognized as long-term causes of late failure. Mobile bearing knee replacements were designed to create a durable surface articulation by using a polyethylene insert that articulates with a metallic femoral component and a metallic tibial tray. The purpose of this article is to review clinical and basic scientific studies comparing the clinical results, the biomechanical features, and the kinematic patterns of fixed versus mobile bearing knee designs. Beside the fact that in vitro kinematic studies have shown reduced polyethylene wear in mobile bearings due to increased implant conformity and reduced polyethylene contact stresses, which should hypothetically prolong polyethylene life, various independent studies for both mobile bearing and fixed bearing prostheses have documented results that are comparable in terms of survival and performance.