Development of a maleic acid-based material to selectively solid-phase extract basic compounds from environmental samples.

This study presents a novel mixed-mode weak cation-exchange (WCX) material. This material was prepared by means of the functionalization of a mesoporous divinylbenzene (DVB) resin with maleic acid (maleic acid-DVB), which yielded a high carboxylic moiety content resulting in WCX interactions as well as suitable specific surface area for reversed-phase interactions. After the optimization of the solid-phase extraction (SPE) protocol to enhance the selectivity of the sorbent, this material was evaluated as a novel WCX sorbent in the SPE of a group of drugs from environmental water samples. The method is based on SPE followed by liquid chromatography (LC) coupled to high resolution mass spectrometry (HRMS) with an Orbitrap analyzer, and was validated and applied for the determination of basic drugs in river, effluent and influent wastewater samples. Maleic acid-DVB sorbent yielded suitable recovery rates (57% to 89%) and an acceptable matrix effect (<32%) thanks to the effective washing step included when these environmental waters were loaded through the novel resin. The method was applied to different environmental water samples and some basic drugs were suitably quantified in these environmental samples.

New materials in sorptive extraction techniques for polar compounds.

This paper provides an overview of the new developments in material and format technology that improve the extraction of polar compounds in several extraction techniques. They mainly include solid-phase extraction, but there are also other sorptive extraction techniques, such as stir bar sorptive extraction and solid-phase microextraction that use either fibers or in-tube devices. We focus on new synthesised materials that are both commercially available and "in-house". Most novel materials that enhance the extraction of polar compounds are hydrophilic and have large specific surface area; however, we also cover other leading technologies, such as sol-gel or monolith. We describe the morphological and chemical properties of these new sorbents so that we can better understand them and relate them to their capability of retaining polar compounds. We discuss the extraction efficiency for polar compounds when these polymers are used as sorptive material and compare them to other materials. We also mention some representative examples of applications.

Solid-phase extraction followed by liquid chromatography-high resolution mass spectrometry to determine synthetic cathinones in different types of environmental water samples.

Synthetic cathinones have become popular in recent years, which would explain why their determination in influent sewage samples has already been documented. In the present study a method based on solid-phase extraction followed by liquid chromatography and high resolution mass spectrometry is developed, validated and applied to determine twelve cathinones and one of their metabolites in different environmental samples including influent and effluent sewage and river water. Two cation-exchange sorbents (Oasis MCX and Oasis WCX) were compared, with better results achieved with Oasis WCX in terms of apparent recoveries (70-100%) and matrix effects (lower than -34%). The method was validated with effluent sewage samples providing suitable figures of merit, with method quantification limits ranging from 1ng/L to 5ng/L and method detection limits from 0.1ng/L to 0.5ng/L for all the compounds. Of the different cathinones studied, three, namely methylone, mephedrone metabolite and methylenedioxypyrovalerone, were quantified at concentration levels of low ng/L in each of the different samples analysed, while a number of the other cathinones were also detected in some of the samples.

Solid-phase extraction of polycyclic aromatic compounds.

Solid-phase extraction (SPE) for two groups of polyaromatic compounds--polycyclic aromatic hydrocarbons and naphthalenesulfonates--with completely different problems in the extraction process are reviewed. The sorbents used in each case and the different steps of SPE are studied. Particular problems encountered in the SPE of each group are described. Adsorption problems of PAHs which require an organic solvent or a surfactant to be added to the sample are explained. The need of ion-pair solid-phase extraction for extracting naphthalenesulfonates and the influence of the inorganic species in the extraction are discussed. The on-line systems are described for both group of compounds.

Identification of pesticides by liquid chromatography--particle beam mass spectrometry using electron ionization and chemical ionization.

Liquid chromatography-mass spectrometry (LC-MS) with a particle beam (PB) interface is used to separate and identify a group of pesticides. The mass spectra obtained under the different ionization modes, electron ionization (EI) and positive and negative chemical ionization (PCI and NCI) are compared. The operating conditions under each mode, determined by studying the influence on the ion abundance of the ion source temperature of the EI mode, and the gas pressure and ion source temperature in the methane CI were optimized. EI was more sensitive than PCI and NCI and of the latter two modes, NCI gave higher responses, especially for organophosphorus compounds. When on-line solid-phase extraction-LC-PB-MS was applied to real samples, limits of detection in full scan mode were in the range of 0.5 and 10 micrograms l-1 for EI. The analysis of real samples by on-line solid-phase extraction-LC-PB-MS enabled EI detection of one of the pesticides studied and confirmation by PCI and NCI. The combined EI/CI information also enabled the detection of some non-target compounds.

Determination of naphthalenesulfonates in water by on-line ion-pair solid-phase extraction and ion-pair liquid chromatography with fast-scanning fluorescence detection.

A fast analytical method for quantifying a mixture of 12 naphthalenesulfonates and naphthalenedisulfonates has been developed. This method consists of on-line ion-pair solid-phase extraction with PLRP-s sorbent and ion-pair liquid-chromatography using fast-scanning fluorescence spectrometer as a detection system and multivariate calibration. As complete separation is unnecessary, the compounds were analysed in isocratic conditions and the chromatographic analysis took only 25 min. Three-way partial least-squares (PLS) was used to carry out multivariate calibration for spiked tap water. In these conditions, quantification limits were between 0.01 and 3 microg x l(-1). Repeatability was also evaluated and relative standard deviations (n=3) were between 0.5 and 4, depending on the compound. Finally, spiked tap and Ebro river waters were analysed to evaluate prediction capability of the method.

Determination of endocrine-disrupting compounds in water samples by on-line solid-phase extraction-programmed-temperature vaporisation-gas chromatography-mass spectrometry.

We developed an automated on-line solid-phase extraction (SPE)-gas chromatography-mass spectrometry method to determine a group of endocrine disruptors in water samples. The interface device used for connecting SPE with GC was a programmed-temperature vaporiser (PTV) whose liner was packed with Tenax. We optimized the parameters that affected both SPE and PTV working in solvent vent mode. The performance of the method was tested with several environmental water samples. The limits of detection of the method were between 0.001 and 0.036 microg l(-1) under full-scan acquisition mode. We determined phthalates and adipate in all real samples at concentrations between 0.11 and 8.10 microg l(-1). Atrazine and p,p'-DDE were also found in an irrigation stream water sample at 0.16 and 0.04 microg l(-1), respectively.

Determination of phthalate esters in water samples by solid-phase microextraction and gas chromatography with mass spectrometric detection.

Solid-phase microextraction (SPME) with an 85 microm polyacrylate fiber, coupled to gas chromatography-mass spectrometry was used to determine six phthalate esters and bis(2-ethylhexyl) adipate in water samples. The variables affecting the SPME absorption process were optimized and the method developed was applied to analyze both tap and commercial mineral water samples as well as water from the Ebro river and fishing and industrial ports. For real samples, the linear range in full scan acquisition mode was between 0.02 and 10 microg l(-1) for most compounds, and the limits of detection of the method were between 0.006 and 0.17 microg l(-1). Commercial water samples contained in recipients which were made from different materials were analyzed, and the influence of the material of the recipients on the concentration of phthalates was evaluated.

Trace determination of antifouling compounds by on-line solid-phase extraction-gas chromatography-mass spectrometry.

A new method based on solid-phase extraction (SPE) on-line coupled to gas chromatography-mass spectrometry through an on-column interface has been applied to determine three antifouling compounds in water samples. Parameters affecting the SPE process and transfer step have been optimised and the method developed has been applied to the analysis of marinas, fishing ports and Ebro river water. The method allows the analytes to be detected at 0.01 microgram l-1 in SIM acquisition mode by preconcentrating only 10 ml of water sample. Different marina and fishing port water samples have been analysed and Irgarol 1051 has been found in some of them at a concentration level equal or lower than 0.05 microgram l-1.

Solid-phase microextraction of the antifouling Irgarol 1051 and the fungicides dichlofluanid and 4-chloro-3-methylphenol in water samples.

Three pesticides usually added to paint formulations, Irgarol 1051, dichlofluanid and 4-chloro-3-methylphenol, were determined by solid-phase microextraction (SPME) with 85-micron polyacrylate fibers and gas chromatography-mass spectrometry. The parameters affecting the SPME process (the pH, the addition of salt to the sample, and the time and temperature of the absorption step) were optimized. The method developed was applied to the analysis of water samples from Ebro river, marinas and fishing ports. The method enables these compounds to be detected at concentrations between 0.2 and 3.0 micrograms l-1 under full scan conditions and between 0.05 and 0.08 microgram l-1 under SIM mode.

On-line coupling of solid-phase extraction to gas chromatography with mass spectrometric detection to determine pesticides in water.

A group of pesticides with different chemical structures was determined in water by on-line coupling of solid-phase extraction to gas chromatography with mass spectrometric detection through an on-column interface. A 10 mm x 2 mm I.D. precolumn packed with PLRP-S was selected for the solid-phase extraction process. The parameters affecting the transfer of the analytes from the precolumn to the GC system (e.g. flow-rate, temperature and solvent vapor exit time) were optimized. An organic modifier was added to the sample before the extraction process to avoid adsorption problems. The use of the MS detector under selected ion monitoring acquisition enabled the analytes to be quantified at sub microgram-per-litre levels preconcentrating only 10 ml of sample, and the limits of detection (S/N = 3) were between 2 and 20 ng l-1. The method was applied to the determination of the pesticides in tap and river water, and molinate was determined in Ebro river water.

New chemically modified polymeric resin for solid-phase extraction of pesticides and phenolic compounds from water.

A new chemically modified polymeric resin, with an o-carboxybenzoyl moiety, is developed to be used in the on-line solid-phase extraction (SPE) of some pesticides and phenolic compounds from aqueous samples, in order to obtain better breakthrough volumes than other commercial sorbents. The chemical introduction of this moiety improves the efficiency of SPE by providing better surface contact with aqueous samples. This synthesized sorbent enables higher volumes of sample to be concentrated for determining polar compounds. When analyzing real samples, tap and river waters, different quantities of sulphite were added to decrease the initial band due to fulvic and humic acids. The matrix peaks decreased and there were no losses in the studied compounds observed when 500 and 1000 microliters of 10% Na2SO3 solution for every 100 ml of sample were added to tap and river water, respectively.

Monitoring of antifouling agents in water samples by on-line solid-phase extraction-liquid chromatography-atmospheric pressure chemical ionization mass spectrometry.

An automatic method for determining diuron, irgarol 1051, folpet and dichlofluanid in seawater samples have been developed. This method is based on the on-line coupling of solid-phase extraction (SPE) with a highly crosslinked polymeric sorbent, LiChrolut EN, to liquid chromatography followed by atmospheric pressure chemical ionization (APCI) and mass spectrometry. The operational parameters affecting the APCI interface have been studied in both positive and negative ionization modes. The use of LiChrolut EN in the SPE produced recoveries of over 85% for all the compounds when 100 ml of seawater sample was preconcentrated. Calibration was carried out in both ionization modes and in full-scan and selected-ion monitoring (SIM). The method allowed all the analytes to be detected at 5 ng l(-1) in SIM acquisition mode except folpet, which, because of its low response, could only be detected at 250 ng l(-1). The method was used to analyse water samples taken from five different marina and fishing ports along the coast of Tarragona, Catalonia (Spain), over a 5-month period. Diuron and irgarol 1051 were detected and quantified in most samples at concentration levels ranging from 27 to 420 ng l(-1) for diuron and from 15 to 511 ng l(-1) for irgarol 1051.

Comparison of different fibers for the solid-phase microextraction of phthalate esters from water.

Solid-phase microextraction (SPME) coupled to gas chromatography-mass spectrometry (GC-MS) has been applied to determine six phthalate esters and one adipate ester in water. The SPME parameters were optimized for several commercially available fibers. A 65-microm polydimethylsiloxane-divinylbenzene (PDMS-DVB) was the fiber selected and was applied to analysis of water from the Ebro river and the industrial port of Tarragona. The studied compounds were found at concentrations ranging from 0.4 microg l(-1) for di-n-butyl phthalate ester (DnBP) to 3.2 microg l(-1) for bis(2-ethylhexyl) phthalate ester (DEHP). The linear range for real samples was from 0.1 to 10 microg l(-1) for most phthalates, and the limits of detection of the method were between 3 and 30 ng l(-1). Repeatability and reproducibility between days (n = 5) for 1 microg l(-1) samples were below 13 and 18%, respectively.

Stir bar sorptive extraction and large volume injection gas chromatography to determine a group of endocrine disrupters in water samples.

Stir bar sorptive extraction (SBSE) combined with gas chromatography (GC) with mass spectrometric detection (MS) has been applied to determine a group of suspected endocrine disrupters in water samples. One centimeter stir bars coated with PDMS were used to extract the analytes and then solvent desorption was carried out. The absorption and desorption parameters in SBSE were optimized and large volume injection was used with a programmed temperature vaporizer injector (PTV) in GC to enhance the sensitivity of the method. The linear range of some endocrine disrupters was between 0.05 and 5 microg l(-1) and limits of detection were 0.01-0.24 microg l(-1) under full scan acquisition mode. The repeatability and reproducibility of the method (n = 5) for Ebro river water samples spiked at a level of 0.5 microg l(-1) was below 13 and 23%, respectively. Recoveries between 42 and 96% were obtained with the exception of atrazine. The method was applied to analyze real water samples from the Ebro River and irrigation streams of Ebro Delta and some of the compounds studied (aldrin, dieldrin, 4,4'-DDE and 4,4'-DDT) were found in some of them between detection and quantification limits.

Solid-phase microextraction coupled to high-performance liquid chromatography to determine phenolic compounds in water samples.

Solid-phase microextraction (SPME) coupled to high-performance liquid chromatography (HPLC) with ultraviolet (UV) and electrochemical detection (ED) has been applied to determine 11 phenolic compounds considered priority pollutants by the US Environmental Protection Agency. 85 microm polyacrylate fibers were used to extract the analytes from the aqueous samples. Two different designs of the liquid chromatograph were compared in combination with SPME. Dynamic and static modes of desorption in both HPLC designs were compared and the variables affecting both absorption and desorption processes in SPME-HPLC were optimized. Static desorption in both HPLC systems showed better recoveries for the phenolic compounds. The performance of the SPME-HPLC-UV-ED method was evaluated with river water and wastewater samples. The method enabled the determination of phenolic compounds at low levels in these water samples.

Method based on solid-phase microextraction--high-performance liquid chromatography with UV and electrochemical detection to determine estrogenic compounds in water samples.

We determined a group of estrogenic compounds by solid-phase microextraction (SPME) coupled to high-performance liquid chromatography (HPLC) with both ultraviolet (UV) and electrochemical detection (ED). A modified liquid chromatograph was used. Polyacrylate fibers (85 microns) were used to extract the analytes from the aqueous samples. Dynamic and static modes of desorption were compared and the variables affecting both absorption and desorption processes in SPME-HPLC were optimized. Static desorption gave the best recoveries and peak shapes. The performance of the SPME-HPLC-UV-ED method was checked with river water and wastewater. The method enabled estrogenic compounds to be determined at low-microgram l-1 levels in real water samples. Limits of detection were between 0.3 and 1.1 micrograms l-1 using UV detection and between 0.06 and 0.08 microgram l-1 using ED. beta-Estradiol was found in samples from a wastewater treatment plant at concentrations between 1.9 and 2.2 micrograms l-1.

Application of on-line solid-phase extraction-gas chromatography-mass spectrometry to the determination of endocrine disruptors in water samples.

We have applied a method based on solid-phase extraction (SPE), on-line coupled to gas chromatography-mass spectrometry through an on-column interface, to determine a group of endocrine-disrupting compounds in water samples. We have optimised the parameters affecting the SPE process and transfer step and used the method to analyse river, coastal and tap waters. In the full-scan acquisition mode, all the compounds were determined by preconcentrating only 15 ml of water sample. Di-n-butyl phthalate, benzylbutyl phthalate, bis(2-ethylhexyl) phthalate and bis(2-ethylhexyl) adipate at concentrations between 0.02 and 0.5 microg l(-1) were determined in some real samples.

On-line solid-phase extraction coupled to supercritical fluid chromatography to determine phenol and nitrophenols in water.

Determining of phenol and nitrophenols using solid-phase extraction on-line coupled to supercritical fluid chromatography (SFC) is studied. SFC quickly separated the compounds studied, in less than 6 min, and solid-phase extraction was used to decrease the limits of detection. C18, PLRP-S and a highly cross-linked styrene-divinylbenzene copolymer in a 10 x 3 mm I.D. laboratory-packed precolumn were tested comparatively as sorbents in the preconcentration step. Tetrabutylammonium bromide was used as ion-pair reagent in the extraction process to increase breakthrough volumes, mainly for phenol. Performance of the method was checked with tap and river waters.

Optimization of solid-phase microextraction conditions using a response surface methodology to determine organochlorine pesticides in water by gas chromatography and electron-capture detection.

A response surface methodology was applied to optimise the solid-phase microextraction (SPME) conditions using a polyacrylate-coated fiber to determine thirteen organochlorine pesticides from water. Analyses were performed using gas chromatography-electron-capture detection. Variables affecting absorption in both the headspace and immersion extraction were optimised by using a response surface generated with a Doehlert design, and the results were compared. The immersion SPME method was selected since higher recoveries were obtained for most of the compounds studied. The method developed was applied to the analysis of tap and Ebro river water samples. The linear range of most pesticides for real samples was found to be between 0.001 and 2.5 micrograms l-1 and the limits of detection were between 0.15 and 0.35 ng l-1. The repeatability and the reproducibility between days of the method (n = 6), expressed as relative standard deviation, for tap water spiked at a level of 1 ng l-1 were between 5.7 and 25.6% and between 7.6 and 26.5%, respectively.