Insights of Fe2O3 and MoO3 Electrodes for Electrocatalytic CO2 Reduction in Aprotic Media.

Transition metal oxides (TMO) have been successfully used as electrocatalytically active materials for CO2 reduction in some studies. Because of the lack of understanding of the catalytic behavior of TMOs, electrochemical methods are used to investigate the CO2 reduction in thin-film nanostructured electrodes. In this context, nanostructured thin films of Fe2O3 and MoO3 in an aprotic medium of acetonitrile have been used to study the CO2 reduction reaction. In addition, a synergistic effect between CO2 and the TMO surface is observed. Faradic cathodic processes not only start at lower potentials than those reported with metal electrodes, but also an increase in capacitive currents is observed, which is directly related to an increase in oxygen vacancies. Finally, the results obtained show CO as a product of the reduction.

Graphene oxide obtention via liquid phase exfoliation from high-rank coal: A comparison of mineral matter removal by alkaline bath.

Colombia is one of the world's leading exporters of coal and coke, with significant reserves of high-quality coal. Most of the coal exported from Colombia is used for power generation, but there is also a class of coal that is suitable for making coke. Coke is a raw material required for making steel, and it is produced by heating coal to high temperatures in the absence of air. Colombia is the third-largest global exporter of coke, with a significant portion of its exports going to the steel industry in countries such as Brazil, Mexico, and the United States. The country's high-quality coal reserves and proximity to major markets make it an important player in the global coal and coke trade. On the other hand, graphene and its derivative Graphene Oxide (GO) have unique properties that make them suitable for a wide range of commercial applications. Graphene has exceptional mechanical strength and high electrical conductivity, which make it an attractive material for a variety of electronic and structural applications. For example, graphene-based materials are being developed for use in flexible electronic devices, sensors, and high-strength composites. GO, on the other hand, is highly resistive but still retains exceptional mechanical strength. This makes it useful in applications where electrical conductivity is not necessary but mechanical strength and durability are important. Graphene production using current techniques can be expensive and inefficient, which limits its widespread adoption for commercial applications. However, new production methods, such as Liquid Phase Exfoliation (LPE), are being developed to address these challenges. LPE is a method for producing graphene and graphene oxide that involves using a liquid solvent to break apart graphite into individual graphene sheets. This method is more efficient and cost-effective than traditional methods such as mechanical exfoliation and chemical vapor deposition. In recent years, there has been increasing interest in using high-rank coal from Colombia as a raw material for graphene production using LPE. This is because high-rank coal from Colombia is known to have a high carbon content and low impurity levels, which makes it an ideal raw material for graphene production. Researchers have successfully produced GO using the LPE method and high-rank coal from Boavita, Colombia. This has the potential to significantly increase the supply of graphene and graphene oxide, making it more accessible for commercial applications. Additionally, using coal as a raw material for graphene production has the potential to create a new market for coal, which could benefit the Colombian economy. In order to synthesize GO, it is important to establish a suitable protocol for the grinding procedure and particle size selection. (i. more than 0.15 mm, ii. 0.15 mm to 0.05 mm, and iii. less than 0.05 mm) were defined. To compare the yield, the mineral matter removal procedure was carried out with a basic leaching bath. Coal oxidation was performed using the modified Hummers process, and GO was then obtained using LPE. This method has the following advantages:•It is feasible to produce GO from high-rank coal with acceptable quality and particulate size smaller than 0.15 mm, yields that are close to 5%, and flakes with fewer than 15 layers.•This approach also could eliminate dependence on graphite as the carbon feedstock for graphene production.•It is an alternative to manufacture GO from coal dust collected from mines.

Effect of the Surface Chemical Composition on the Corrosion Resistance in the Mixture of FeCrMoNbB (140MXC) and FeCMnSi (530AS) Coatings Produced with the Electric Wire Arc Spraying Technique: Part I.

In this study, FeCrMoNbB (140MXC) and FeCMnSi (530AS) coatings were simultaneously projected on the substrate AISI-SAE 4340 using the electric wire arc spraying technique. The projection parameters, such as current (I), voltage (V), primary air pressure (1st), and secondary air pressure (2nd), were determined using the experimental model Taguchi L9 (34-2). Its main purpose is to produce dissimilar coatings and to evaluate the effect of the surface chemical composition on the corrosion resistance in the mixture of 140MXC-530AS as commercial coatings. Three phases were considered to obtain and characterize the coatings: Phase 1: Preparation of materials and projection equipment; Phase 2: Coatings production; and Phase 3: Coatings characterization. The characterization of the dissimilar coatings was carried out using the techniques of Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDX), Auger Electronic Spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). The results of this characterization corroborated the electrochemical behavior of the coatings. The presence of B was determined with the XPS characterization technique in the mixtures of the coatings in the form of Iron Boride. Moreover, the XRD technique showed Nb in the form of FeNb as a precursor compound for the 140MXC wire powder. The most relevant contributions are the pressures, provided that the quantity of oxides in the coatings decreases with respect to the reaction time between the molten particles and the atmosphere of the projection hood; moreover, for the corrosion potential, the operating voltage of the equipment does not exert any effect since these tend to remain constant.