Electrocatalysis in Alkaline Media and Alkaline Membrane-Based Energy Technologies.

Hydrogen energy-based electrochemical energy conversion technologies offer the promise of enabling a transition of the global energy landscape from fossil fuels to renewable energy. Here, we present a comprehensive review of the fundamentals of electrocatalysis in alkaline media and applications in alkaline-based energy technologies, particularly alkaline fuel cells and water electrolyzers. Anion exchange (alkaline) membrane fuel cells (AEMFCs) enable the use of nonprecious electrocatalysts for the sluggish oxygen reduction reaction (ORR), relative to proton exchange membrane fuel cells (PEMFCs), which require Pt-based electrocatalysts. However, the hydrogen oxidation reaction (HOR) kinetics is significantly slower in alkaline media than in acidic media. Understanding these phenomena requires applying theoretical and experimental methods to unravel molecular-level thermodynamics and kinetics of hydrogen and oxygen electrocatalysis and, particularly, the proton-coupled electron transfer (PCET) process that takes place in a proton-deficient alkaline media. Extensive electrochemical and spectroscopic studies, on single-crystal Pt and metal oxides, have contributed to the development of activity descriptors, as well as the identification of the nature of active sites, and the rate-determining steps of the HOR and ORR. Among these, the structure and reactivity of interfacial water serve as key potential and pH-dependent kinetic factors that are helping elucidate the origins of the HOR and ORR activity differences in acids and bases. Additionally, deliberately modulating and controlling catalyst-support interactions have provided valuable insights for enhancing catalyst accessibility and durability during operation. The design and synthesis of highly conductive and durable alkaline membranes/ionomers have enabled AEMFCs to reach initial performance metrics equal to or higher than those of PEMFCs. We emphasize the importance of using membrane electrode assemblies (MEAs) to integrate the often separately pursued/optimized electrocatalyst/support and membranes/ionomer components. Operando/in situ methods, at multiscales, and ab initio simulations provide a mechanistic understanding of electron, ion, and mass transport at catalyst/ionomer/membrane interfaces and the necessary guidance to achieve fuel cell operation in air over thousands of hours. We hope that this Review will serve as a roadmap for advancing the scientific understanding of the fundamental factors governing electrochemical energy conversion in alkaline media with the ultimate goal of achieving ultralow Pt or precious-metal-free high-performance and durable alkaline fuel cells and related technologies.

Design, Synthesis and Aromaticity of an Alternating Cyclo[4]Thiophene[4]Furan.

A new class of conjugated macrocycle, the cyclo[4]thiophene[4]furan hexyl ester (C4TE4FE), is reported. This cycle consists of alternating α-linked thiophene-3-ester and furan-3-ester repeat units, and was prepared in a single step using Suzuki-Miyaura cross-coupling of a 2-(thiophen-2-yl)furan monomer. The ester side groups help promote a syn conformation of the heterocycles, which enables formation of the macrocycle. Cyclic voltammetry studies revealed that C4TE4FE could undergo multiple oxidations, so treatment with SbCl5 resulted in formation of the [C4TE4FE]2+ dication. Computational work, paired with 1 H NMR spectroscopy of the dication, revealed that the cycle becomes globally aromatic upon 2e- oxidation, as the annulene pathway along the outer ring becomes Hückel aromatic. The change in ring current for the cycle upon oxidation was clear from 1 H NMR spectroscopy, as the protons of the thiophene and furan rings shifted downfield by nearly 6 ppm. This work highlights the potential of sequence control in furan-based macrocycles to tune electronic properties.

Direct Insertion Polymerization of Ionic Monomers: Rapid Production of Anion Exchange Membranes.

The limited number of methods to directly polymerize ionic monomers currently hinders rapid diversification and production of ionic polymeric materials, namely anion exchange membranes (AEMs) which are essential components in emerging alkaline fuel cell and electrolyzer technologies. Herein, we report a direct coordination-insertion polymerization of cationic monomers, providing the first direct synthesis of aliphatic polymers with high ion incorporations and allowing facile access to a broad range of materials. We demonstrate the utility of this method by rapidly generating a library of solution processable ionic polymers for use as AEMs. We investigate these materials to study the influence of cation identity on hydroxide conductivity and stability. We found that AEMs with piperidinium cations exhibited the highest performance, with high alkaline stability, hydroxide conductivity of 87 mS cm-1 at 80 °C, and a peak power density of 730 mW cm-2 when integrated into a fuel cell device.

Examining the Alkaline Stability of Tris(dialkylamino)sulfoniums and Sulfoxoniums.

Herein, a synthetic method was developed to prepare a series of tris(dialkylamino)sulfonium and sulfoxonium cations from sulfur monochloride. Alkaline stability studies of these two cation families in 2 M KOH/CD3OH solution at 80 °C revealed how degradation pathways change as a function of the oxidation state of the S center, as determined by 1H NMR spectroscopy. The sulfonium cations (+S(NR2)3) typically degrade by nucleophilic attack at the sulfur atom with loss of an amino group and a proton transfer reaction to produce sulfoxides, while the sulfoxoniums (+O═S(NR2)3) tend to degrade by loss of an R group to form sulfoximines. From the group of sulfoniums and sulfoxoniums explored in this work, the tris(piperidino)sulfoxonium cation was noted to have excellent alkaline stability. This sulfoxonium should be suitable for future examination as a tethered cation in anion-exchange membranes (AEMs), or as a phase-transfer catalyst in biphasic reactions.

Degradation of Organic Cations under Alkaline Conditions.

Understanding the degradation mechanisms of organic cations under basic conditions is extremely important for the development of durable alkaline energy conversion devices. Cations are key functional groups in alkaline anion exchange membranes (AAEMs), and AAEMs are critical components to conduct hydroxide anions in alkaline fuel cells. Previously, we have established a standard protocol to evaluate cation alkaline stability within KOH/CD3OH solution at 80 °C. Herein, we are using the protocol to compare 26 model compounds, including benzylammonium, tetraalkylammonium, spirocyclicammonium, imidazolium, benzimidazolium, triazolium, pyridinium, guanidinium, and phosphonium cations. The goal is not only to evaluate their degradation rate, but also to identify their degradation pathways and lead to the advancement of cations with improved alkaline stabilities.

Chemoselective Rhodium-Catalyzed Borylation of Bromoiodoarenes Under Mild Conditions.

A chemoselective rhodium-catalyzed borylation has been developed for the preparation of aryl boronate esters. The reaction proceeds under mild conditions with excellent selectivity for C-I bonds in bromoiodoarenes and exhibits broad functional group tolerance. This procedure can act as a complementary approach toward bifunctional arenes along with other metal-catalyzed borylations. Additionally, the reaction's utility in the preparation of monomers for metal-catalyzed cross-coupling polymerization is demonstrated.

Photostable Helical Polyfurans.

This report describes the design and synthesis of a new class of polyfurans bearing ester side chains. The macromolecules can be synthesized using catalyst-transfer polycondensation, providing precise control over molecular weight and molecular weight distribution. Such obtained furan ester polymers are significantly more photostable than their alkyl analogues owing to the electron-withdrawing nature of the attached subunit. Most interestingly, they spontaneously fold into a compact π-stacked helix, yielding a complex multilayer cylindrical nanoparticle with a hollow, rigid, conjugated core composed of the polyfuran backbone and a soft, insulating outer layer formed by the ester side chains. The length of polymer side chains dictates the outer diameter of such nanoparticles, which for the hexyl ester groups used in the present study is equal to ∼2.3 nm. The inner cavity of the conjugated core is lined with oxygen atoms, which set its effective diameter to 0.4 nm. Furthermore, installation of bulkier, branched chiral ester side chains on the repeat unit yields structures that, upon change of solvent, can reversibly transition between an ordered chiral helical folded and disordered unfolded state.

Diversifying Cross-Coupling Strategies, Catalysts and Monomers for the Controlled Synthesis of Conjugated Polymers.

Chain-growth polymerization of aromatic building blocks (termed catalyst-transfer polycondensation or CTP) has emerged as a powerful method for the controlled synthesis of conjugated polymers. CTP affords semiconducting materials with predictable molecular weights, relatively narrow molar mass distributions and tailored backbone compositions (e.g. blocks, gradients, stars). Homogeneous catalysis utilizing transition metals has played a critical role in the rise of this field and this Minireview is designed to highlight some of the catalysts employed for these polycondensations. Some descriptions of the metal and ancillary ligands are included, along with which catalysts have been used for different aromatic monomers. Cross-coupling strategies are discussed briefly for ease of use. Finally, some potential future directions are described for further evolution of this exciting area.

Conjugated Polymers with Repeated Sequences of Group 16 Heterocycles Synthesized through Catalyst-Transfer Polycondensation.

Periodic π-conjugated polymers of the group 16 heterocycles (furan, thiophene, and selenophene) were synthesized with controlled chain lengths and relatively low dispersities using catalyst-transfer polycondensation. The optical gap and redox potentials of these copolymers were fine-tuned by altering the heterocycle sequence, and atomic force microscopy revealed nanofibrillar morphologies for all the materials. Grazing incidence wide-angle X-ray scattering of the thiophene-selenophene copolymers indicated that the π-stacking distance increased with incorporation of the larger heteroatom (from ∼3.7-4.0 Å), while the lamellar spacing decreased (from ∼15.8-15.2 Å). The study also revealed that periodic sequences allow electronic properties to be tuned while retaining nanofibrillar morphologies similar to those observed for poly(3-hexylthiophene).

Electron-Poor Thiophene 1,1-Dioxides: Synthesis, Characterization, and Application as Electron Relays in Photocatalytic Hydrogen Generation.

The synthesis and characterization of electron-poor thiophene 1,1-dioxides bearing cyanated phenyl groups are reported. The electron-accepting nature of these compounds was evaluated by cyclic voltammetry, and highly reversible and facile reductions were observed for several derivatives. Moreover, some of the reduced thiophene dioxides form colorful anions, which were investigated spectroelectrochemically. Photoluminescence spectra of the electron-deficient sulfones were measured in CH2 Cl2, and they emit in the blue-green region with significant variation in the quantum yield depending on the aryl substituents. By expanding the degree of substitution on the phenyl rings, quantum yields up to 34 % were obtained. X-ray diffraction data are reported for two of the thiophene 1,1-dioxides, and the electronic structure was probed for all synthesized derivatives through DFT calculations. The dioxides were also examined as electron relays in a photocatalytic water reduction reaction, and they showed potential to boost the efficiency.

Stille Catalyst-Transfer Polycondensation Using Pd-PEPPSI-IPr for High-Molecular-Weight Regioregular Poly(3-hexylthiophene).

A commercially available palladium N-heterocyclic carbene (Pd-NHC) precatalyst is used to initiate chain-growth polymerization of 2-bromo-3-hexyl-5-trimethylstannylthiophene. The molecular weight of the resultant poly(3-hexylthiophene) can be modulated (7 to 73 kDa, D = 1.14 to 1.53) by varying the catalyst concentration. Mass spectrometry data confirm control over the polymer end groups and (1)H NMR spectroscopy reveals that the palladium catalyst is capable of "ring-walking". A linear relationship between Mn and monomer conversion is observed. Atomic force microscopy and X-ray scattering verify the regioregular nature of the resultant polythiophene.

Tuning thiophene with phosphorus: synthesis and electronic properties of benzobisthiaphospholes.

1,4-Dimercapto-2,5-diphosphinobenzene and 3,6-bis(hexyloxy)-1,4-dimercapto-2,5-diphosphinobenzene were synthesized and combined with various acid chlorides to obtain a series of benzobisthiaphospholes. Electrochemical and photophysical properties of the substituted benzobisthiaphospholes have been evaluated, and the observed reductions are more facile than the related benzothiaphospholes and 2,6-diphenylbenzobisthiazole. A benzobisthiaphosphole with C6H4-p-CN substituents was reduced at E(1/2)=-1.08 V (vs. saturated calomel electrode (SCE)). X-ray diffraction data for several of these phosphorus heterocycles has been obtained, and DFT calculations at the B3LYP level have been performed.

Comparing Ammonium and Tetraaminophosphonium Anion-Exchange Membranes Derived from Vinyl-Addition Polynorbornene Copolymers.

Herein, we systematically examined how composition influenced the properties of vinyl addition polynorbornene anion exchange membranes (AEMs) prepared from 5-n-hexyl-2-norbornene and 5-(4-bromobutyl)-2-norbornene. Copolymerization kinetics revealed that 5-n-hexyl-2-norbornene is consumed faster than 5-(4-bromobutyl)-2-norbornene, leading to a portion of the chain being richer in bromoalkyl groups. The alkyl halide pendants can then be converted to either trimethylammonium or tetrakis(dialkylamino)phosphonium cations through straightforward substitution with trimethylamine or a tris(dialkylamino)phosphazene. A series of cationic ammonium polymers were synthesized first, where conductivity and water uptake increased as a function of increasing ionic content in the polymer. The optimized copolymer had a hydroxide conductivity of 95 ± 6 mS/cm at 80 °C. The living polymerization of the two monomers catalyzed by a cationic tert-butylphosphine palladium catalyst also enabled precise changes in the molecular weight while keeping the functional group concentration constant. Molecular weight did not have a significant impact on hydroxide conductivity over the range of ∼60-190 kg/mol (Mn). The optimized tetraaminophosphonium AEM had the highest conductivity for any tetraaminophosphonium polymer to date (70 ± 3 mS/cm at 80 °C). Clear phase separation and larger domains were observed for the phosphonium-based AEM compared to the ammonium at an identical composition, which is attributed to the larger occupied volume of the phosphorus cation. Fuel cell studies with the two membranes resulted in peak power densities of 1.59 and 0.79 W/cm2 for the ammonium and tetraaminophosphonium membrane electrode assemblies, respectively. The ammonium-based membrane was more water permeable as evidenced by water limiting current studies, which likely contributed to the improved performance.

Synthetic tuning of electronic and photophysical properties of 2-aryl-1,3-benzothiaphospholes.

A series of 2-aryl-1,3-benzothiaphospholes have been synthesized from 1-mercapto-2-phosphinobenzene and a variety of acid chlorides. The structure of 2-phenyl-1,3-benzothiaphosphole was established using X-ray diffraction. The electrochemical and photophysical properties of each benzothiaphosphole are reported and some of these molecules exhibit reversible 1-electron reductions.

Biocidal Potency of Polymers with Bulky Cations.

The performance of antimicrobial polymers depends sensitively on the type of cationic species, charge density, and spatial arrangement of cations. Here we report antimicrobial polymers bearing unusually bulky tetraaminophosphonium groups as the source of highly delocalized cationic charge. The bulky cations drastically enhanced the biocidal activity of amphiphilic polymers, leading to remarkably potent activity in the submicromolar range. The cationic polynorbornenes with pendent tetraaminophosphonium groups killed over 98% E. coli at a concentration of 0.1 µg/mL and caused a 4-log reduction of E. coli within 2 h at a concentration of 2 µg/mL, showing very rapid and potent bactericidal activity. The polymers are also highly hemolytic at similar concentrations, indicating a biocidal activity profile. Polymers of a similar chemical structure but with more flexible backbones were made to examine the effects of the flexibility of polymer chains on their activity, which turned out to be marginal. We also explore variants with different spacer arm groups separating the cations from the backbone main chain. The antibacterial activity was comparably potent in all cases, but the polymers with shorter spacer arm groups showed more rapid bactericidal kinetics. Interestingly, pronounced counterion effects were observed. Tightly bound PF6- counteranions showed poor activity at high concentrations due to gross aggregate formation and precipitation from the assay media, whereas loosely bound Cl- counterions resulted in very potent activity that monotonically increased with increasing concentration. In this paper, we reveal that bulky phosphonium cations are associated with markedly enhanced biocidal activity, which provides an innovative strategy to develop more effective self-disinfecting materials.

Phosphonium-functionalized polyethylene: a new class of base-stable alkaline anion exchange membranes.

A tetrakis(dialkylamino)phosphonium cation was evaluated as a functional group for alkaline anion exchange membranes (AAEMs). The base stability of [P(N(Me)Cy)(4)](+) was directly compared to that of [BnNMe(3)](+) in 1 M NaOD/CD(3)OD. The high base stability of [P(N(Me)Cy)(4)](+) relative to [BnNMe(3)](+) inspired the preparation of AAEM materials composed of phosphonium units attached to polyethylene. The AAEMs (hydroxide conductivity of 22 ± 1 mS cm(-1) at 22 °C) were prepared using ring-opening metathesis polymerization, and their stabilities were evaluated in 15 M KOH at 22 °C and in 1 M KOH at 80 °C.

Chain-Growth Polymerization of Benzotriazole Using Suzuki-Miyaura Cross-Coupling and Dialkylbiarylphosphine Palladium Catalysts.

Electron-deficient (n-type) conjugated materials are commonly prepared via step-growth methods with limited control over the molecular weight and molecular weight distribution of the resulting polymers. In this communication, we demonstrate that Pd-dialkylbiarylphosphine catalysts enable the chain-growth polymerization of benzo[1,2,3]triazole using Suzuki-Miyaura coupling with molecular weight control and modest molecular weight distributions (D ∼ 1.2-1.6). The importance of a free ligand in the reaction mixture during polymerization was established by analysis of polymer samples using GPC and MALDI-TOF mass spectrometry. A block copolymer with poly(3-hexylthiophene) was also synthesized by sequential monomer addition. The success of these commercially available catalysts for polymerization of benzotriazole highlights their potential for chain-growth reactions with other bicyclic arenes in the future.

Phosphorus-containing block copolymer templates can control the size and shape of gold nanostructures.

Amphiphilic block copolymers containing phosphine moieties in the main chain are employed as macromolecular ligands for gold(I). The sequential living anionic copolymerization of isoprene (I) and the phosphaalkene, MesP CPh2 (Mes = 2,4,6-trimethylphenyl) affords the block copolymer [PI]404-b-[MesP-CPh2]32 (1a). The incorporation of gold(I) moieties into this functional copolymer is accomplished by treating 1 with THT.AuCl (THT = tetrahydrothiophene) which affords [PI]404-b-[MesP(AuCl)-CPh2]32 (2a). Remarkably, dissolution of gold-functionalized 2 in n-heptane, a block-selective solvent for isoprene, affords spherical micelles with gold(I)-rich cores. Micelles were examined by transmission electron microscopy (TEM) and dynamic light scattering (DLS). We also prepared two additional copolymers with longer phosphine blocks and shorter PI segments: [PI]222-b-[MesP(AuCl)-CPh2]77 (2b) and [PI]164-b-[MesP(AuCl)-CPh2]85 (2c). When assembled in isoprene-selective solvents, 2b forms wormlike structures and 2c, with the longest phosphine block, forms fascinating micron sized intertwined wormlike structures. This represents a new method to control the shape and size of gold(I) nanostructures.

Gene expression and activity of methionine converting enzymes in broiler chickens fed methionine isomers or precursors.

Common dietary supplemental methionine (Met) sources include DL-methionine (DL-Met) and the Met precursor DL-2-hydroxy-4-(methylthio) butanoic acid (DL-HMTBA). For bio-utilization, D-Met and DL-HMTBA are converted into L-Met through oxidation and transamination. The objective of this study was to determine the effect of different dietary supplemental Met sources on gene expression and enzyme activity of Met oxidases in male broiler chickens. Liver, muscle, duodenum, jejunum, and ileum were collected at days 10 (d 10), 21 (d 21), and 26 (d 26) post-hatch from male broiler chickens that were fed a basal diet deficient in sulfur amino acids (SAA) (control), or the control diet supplemented with DL-Met, L-Met, or DL-HMTBA to meet SAA requirements. The mRNA abundance of D-Met oxidase, L-HMTBA oxidase, and D-HMTBA oxidase was measured by real-time PCR, and oxidase activities were measured using colorimetric assays (n = 5). Liver expressed more D- and L-HMTBA oxidase mRNA, while breast muscle and liver expressed more D-Met oxidase mRNA than other tissues. In the liver, DL-HMTBA and L-Met supplementation were associated with greater mRNA abundance of L-HMTBA oxidase compared to the control diet-fed group at d 10 but not d 21 or d 26. DL-HMTBA supplementation, however, was not associated with changes in the mRNA abundance of D-HMTBA oxidase. The Met-deficient diet at d 26 was associated with greater hepatic abundance of DAO mRNA, which is responsible for oxidation of amino acids. Oxidase activities were similar among the Met deficient and Met-supplemented groups. In conclusion, dietary Met supplementation influenced the transcriptional regulation and activity of Met oxidases in a tissue and age-specific manner. Met oxidases may thus act as a determining factor in the bioefficacy of different dietary supplemental Met sources.