Low Molecular Weight Shuttle Molecules Enhance Polychloramide Antimicrobial Activity.

Investigated were the influences of succinimide (SI), 5,5-dimethylhydantoin (DMH), and 3-(hydroxymethyl)-5,5-dimethylhydantoin (HDMH) on the biocidal activity of chlorinated, water-soluble polyamide prepared by the reaction of isopropylamine with poly(styrene-alt-maleic anhydride). The resulting polymer was a negatively charged, water-soluble polymer bearing a carboxylic acid and an isopropylamide moiety on nearly every repeat unit. Subsequent treatment with NaOCl chlorinated the polymers to up to 4.4% Cl while inflicting some polymer chain scission. SI, DMH, or HDMH increased the biocidal activity of polychloramides toward planktonic Escherichia coli and Staphylococcus aureus. Independent solution studies confirmed that oxidative chlorine spontaneously transferred from aqueous polychloramides to small molecules. We concluded that SI, DMH, and HDMH acted as shuttles that extracted oxidative Cl from the polymer chloramides and transported oxidative Cl more efficiently to microbial surfaces. Succinimide was the most effective shuttle. These results warn that some low molecular weight soluble molecules in antimicrobial testing solutions may exaggerate the effectiveness of the polymer or immobilized antimicrobial agents.

Modeling the Impact of Polychloramide Solution Properties on Bacterial Disinfection Kinetics.

Anionic water-soluble polychloramide biocides are of interest because, compared to conventional cationic antimicrobial polymers, anionic biocides are less likely to be sequestered or deactivated by contact with non-microbial soil. Although electrostatics can prevent anionic polymers from adsorbing on microbes, water-soluble polychloramides appear to transfer oxidative chlorine during transient contacts between polymer chains and microbe surfaces. The Chick-Watson model of disinfection kinetics has been modified to account for the contributions of polychloramide molecular weight (MW) and the polychloramide configuration in solution estimated from the overlap concentration, C*, below which dilute polymer chains exist as discrete objects in solution. The key assumption in the modeling was that the transfer rate of oxidative chlorine from polychloramide chains to microbe surfaces impacts the disinfection kinetics. Because both C* and MW are measurable, the polymer-modified Chick-Watson (PCW) model has one less unknown parameter than the two-parameter Chick-Watson equation. The PCW model predicts that lower MW polymers are more effective biocides compared with high MW counterparts. Additionally, polymers with more compressed configurations in solution are more effective biocides. Experimental evidence supports these conclusions. Based on the estimated time scale of bacteria/polymer collisions compared with disinfection kinetics, arguments are made that bacteria surfaces must be contracted many times by polychloramide chains to achieve sufficient Cl transfer to deactivate bacteria.

High Yield Poly(ethylene-alt-maleic acid) Grafting to Wood Pulp while Minimizing Fiber/Fiber Wet Adhesion.

Heating bleached kraft pulps treated with poly(ethylene-alt-maleic acid) (PEMAc) can lead to high yields of carboxylated polymer grafted to fibers. However, in many cases, the cured, dry pulp cannot be effectively repulped (redispersed in water) because the wet strength is too high. Impregnation with PEMAc solutions at pH 4 followed by high temperature (120-180 °C), catalyst-free curing for short times can give fixation yields >85% while maintaining repulpability. The combination of high fixation yields with low wet strength is possible because the extent of curing required for high grafting yields is less than the curing requirement for high wet strength. Two challenges in moving this technology to practicable applications are (1) identifying the optimum laboratory pulp curing conditions and (2) translating laboratory curing conditions to industrial processes. A modeling tool was developed to meet these challenges. The model is based on the observation that for curing conditions giving high fixation yields the wet tensile indices of grafted pulp sheets showed a power-law dependence on the ßΓ product where ß is the conversion of the succinic acid moieties in PEMAc to the corresponding succinic anhydride groups in the curing step and Γ is the amount of polymer applied to the pulp. For two PEMAc molecular weights and two pulp types, the power-law slopes were 0.6; however, the pre-exponential terms depended upon the specific polymer and pulp type combination. We propose that the relationships between the wet tensile index and ßΓ, from polymer-treated, laboratory pulp handsheets, can be used to predict if proposed curing conditions for larger-scale processes will produce a repulpable product.

Challenges to Achieving Strong but Fully Degradable Adhesive Joints between Wet Cellulose Surfaces.

The dramatic loss of strength upon exposure to water is one of the challenges preventing the widespread substitution of plastic packaging with paper and paperboard. Although treatment with conventional wet strength resins and other adhesive polymers can strengthen wet paper, it is at the expense of green credentials, including easy recycling or rapid composting. The goal of this work was to demonstrate the adhesive requirements for strong, wet cellulose-cellulose joints that can be recycled easily because the joint strength can be destroyed by the presence of a weak reducing agent. Cellulose membrane surfaces were first treated with a bound layer of carboxymethyl cellulose, modified to have covalently tethered hydrazide groups. Joints were fabricated by laminating two hydrazide-modified membranes with a polymeric adhesive bearing aldehyde functionality. Aldehydes spontaneously condense with hydrazide to give hydrazone bonds. When the adhesive was oxidized dextran, the wet laminates had an intermediate strength. Upon exposure to a reducing agent, the joint strength was reduced to nearly zero because every hydrazone moiety connecting two cellulose surfaces included a cleavable disulfide linkage. By contrast, glyoxalated cationic polyacrylamide gave very strong wet joints. However, the wet adhesion was dominated by polyelectrolyte complexation, and the presence of hydrazone linkages had little influence on the wet adhesion. We conclude that robust joint degradability will require cleavable linkages in the adhesive backbone while minimizing polyelectrolyte complexation.

Deposited Nanoparticles Can Promote Air Clogging of Piezoelectric Inkjet Printhead Nozzles.

Piezoelectric inkjet printing is susceptible to printhead clogging when printing with inks that contain dispersed particles. This paper investigates the mechanisms by which 28-530 nm nanoparticle dispersions induce printhead clogging without forming large aggregates or thick deposited layers on printhead surfaces. Printing experiments were combined with nanoparticle deposition studies and with experiments where inks were pumped through printheads at a constant flow rate with a syringe pump. Submonolayer coverages of hydrophobic cationic polystyrene nanoparticles adhering to printhead surfaces promote rapid clogging by trapped air that enters from the nozzle opening. We propose that the deposited particles distort the shape of the ink/air meniscus, possibly causing air entrainment, and promote air bubble adhesion to the interior printhead surfaces. The printer's purge-blot cleaning procedure removes air clogs, but the clogs quickly reform when printing is resumed because the adsorbed nanoparticles are not removed by the cleaning procedure. Nondepositing anionic hydrophobic nanoparticles cause much less clogging, possibly because of filtration of trace large aggregates. Colloidal stability is a necessary but not sufficient criterion for ink dispersions; the ink particles must not adsorb onto the printhead surfaces. Thus, alternate surface chemistries for the printhead and ink particle surfaces may be required to print hydrophobic ink materials.

A Colloidal Stability Assay Suitable for High-Throughput Screening.

A library of 32 polystyrene copolymer latexes, with diameters ranging between 53 and 387 nm, was used to develop and demonstrate a high-throughput assay using a 96-well microplate platform to measure critical coagulation concentrations, a measure of colloidal stability. The most robust assay involved an automated centrifugation-decantation step to remove latex aggregates before absorbance measurements, eliminating aggregate interference with optical measurements made through the base of the multiwell plates. For smaller nanoparticles (diameter <150 nm), the centrifugation-decantation step was not required as the interference was less than with larger particles. Parallel measurements with a ChemiDoc MP plate scanner gave indications of aggregation; however, the results were less sensitive than the absorbance measurements.

Stable Aqueous Foams from Cellulose Nanocrystals and Methyl Cellulose.

The addition of cellulose nanocrystals (CNC) greatly enhanced the properties of methylcellulose (MC) stabilized aqueous foams. CNC addition decreased air bubble size, initial foam densities and drainage rates. Mixtures of 2 wt % CNC + 0.5 wt % MC gave the lowest density foams. This composition sits near the onset of nematic phase formation and also near the overlap concentration of methylcellulose. More than 94% of the added CNC particles remained in the foam phase, not leaving with the draining water. We propose that the nanoscale CNC particles bind to the larger MC coils both in solution and with MC at the air/water interface, forming weak gels that stabilize air bubbles. Wet CNC-MC foams were sufficiently robust to withstand high temperature (70 °C for 6 h) polymerization of water-soluble monomers giving macroporous CNC composite hydrogels based on acrylamide (AM), 2-hydroxyethyl methacrylate (HEMA), or polyethylene glycol diacrylate (PEGDA). At high temperatures, the MC was present as a fibrillar gel phase reinforced by CNC particles, explaining the very high foam stability. Finally, our CNC-MC foams are based on commercially available forms of CNC and MC, already approved for many applications. This is a "shovel-ready" technology.

Printed paper sensors for serum lactate dehydrogenase using pullulan-based inks to immobilize reagents.

In this study, a paper-based point-of-care (POC) colorimetric biosensor was developed for the detection of lactate dehydrogenase in serum using a nonporous, oxygen impermeable reversibly gelling polysaccharide material based on pullulan. The pullulan could be printed onto paper surfaces along with all required assay reagents, providing a means for high-stability immobilization of all reagents on paper. Serum containing lactate dehydrogenase (LDH) was directly spotted on to the pullulan-coated bioactive paper and provided quantitative colorimetric data that was comparable to that obtained with a conventional plate-reader method. The paper strip was found to be highly stable and could be stored at 4 °C for at least 10 weeks with no loss in performance, as compared to a complete loss in performance within 1 day when the reagents were printed without the stabilizing polysaccharide. The ease of fabrication coupled with the high stability of the printed reagents provides a facile platform for easily manufactured POC sensors.

Emulsion/Surface Interactions from Quiescent Quartz Crystal Microbalance Measurements with an Inverted Sensor.

Interactions of three oil-in-water emulsion types with polystyrene-coated quartz crystal microbalance (QCM) sensor surfaces were probed with the QCM cell in both the conventional orientation (i.e., polystyrene surface on the bottom, "looking up") and the inverted orientation (polystyrene on top interior surface of sensor chamber, "looking down"). With the conventionally oriented QCM sensors, the adsorption of soluble and/or dispersed species quickly gave steady-state frequency and dissipation outputs. By contrast, the inverted sensors gave changing responses at long times because of the gravity driven buildup of a viscous consolidation layer next to but not necessarily bound to the sensor surface. Three emulsion types (a simple hexadecane/phosphatidylcholine emulsion, 2% homogenized milk, and a diluted commercial ophthalmic emulsion) displayed a wide range of behaviors. We propose that quiescent QCM measurement made with an inverted sample chamber is a new approach to probing emulsion behaviors near solid surfaces.

Impacts of non-microbial soils on polychloramide disinfectants.

The presence of some nonmicrobial chemicals and surfaces, herein called "soils", are known to degrade the performance of biocides, and biocidal assays often include mixtures of materials to mimic the effects of soils. We hypothesized that water-soluble anionic polychloramide biocides were less sensitive to soil interference than cationic polymeric biocides. The relationships between soil composition and antimicrobial polymer biocidal activity were compared for an anionic polychloramide, a cationic polychloramide, and a cationic poly(quaternary ammonium) biocide. The nanoscale soil models individually investigated were polyacrylic acid (PAA), cellulose nanocrystals (CNCs), and bovine serum albumin. The low molecular weight model soils were ammonium chloride, glycine, and succinimide. Three types of soil impacts were identified: 1) sequestration, whereby the soil physically inhibited transport of the biocide to microbes; 2) extraction, whereby the soil reduced or extracted oxidative chlorine, decreasing or eliminating the oxidative chlorine strength; and 3) extraction whereby the biocidal activity increases in the presence of a low molecular weight chemical that carries oxidative Cl from the polymer to the microbes. PAA and CNCs inhibit cationic biocides by sequestration but have little impact on anionic polychloramide. Glycine and BSA extract oxidative chlorine, lowering the biocidal activity of the anionic and cationic polychloramides while not impacting the poly(quaternary ammonium) biocide. Finally, the presence of succinimide increased bacteria deactivation of both anionic and cationic polychloramides. We propose that succinimide extracts oxidative chlorine from the polychloramides and transports it to the bacteria.

Water-soluble anionic polychloramide biocides based on maleic anhydride copolymers.

Our goal was to develop film-forming polymers to extend the antimicrobial lifetimes of cleaned and disinfected surfaces. Antimicrobial polymers were prepared by first reacting poly(ethylene-alt-maleic anhydride) with isopropylamine, partially consuming the anhydride groups, followed by hydrolysis to give water-soluble, highly anionic polyamide PC3. Chlorination with NaOCl gave PC3Cl with oxidative chlorine contents up to 9 wt%. Dried, 5 µm thick, PC3Cl films, gave log 4 reductions in the concentration of Escherichia coli or Staphylococcus aureus exposed to films. A unique feature of the maleic anhydride copolymer platform was the ability to form covalent grafts to surfaces via anhydride reactions. PC3 solution was impregnated into cellulosic filter paper, heated to form ester linkages with cellulose, followed by chlorination with sodium dichloroisocyanurate dihydrate giving grafted PC3Cl. The treated paper (0.3 wt% PC3Cl) gave a log 4 reduction of E. coli concentration in 30 min.

Preventing the release of copper chlorophyllin from crop spray deposits on hydrophobic surfaces.

The chlorophyll derivative copper chlorophyllin and related chlorins have promise as environmentally friendly agricultural chemicals, however, spray application is hindered by the propensity of dried spray deposits to wash off leaf surfaces during rain or irrigation. HYPOTHESIS: Polyelectrolyte complexes formed between anionic carboxymethyl cellulose and cationic polyamidoamine-epichlorohydrin can prevent the release of copper chlorophyllin from dried spray deposits on leaf surfaces when exposed to water. EXPERIMENTS: Sessile drops on parafilm and containing polyelectrolyte complex and copper chlorophyllin or Brilliant Sulfaflavine, an anionic water-soluble dye, were dried to form deposits that were physical models for crop spray drop deposits on hydrophobic leaf surfaces. Larger buffer drops were placed on the dried deposits and the release of copper chlorophyllin or the dye were measured. FINDINGS: Copper chlorophyllin showed some immediate (burst) release upon exposure to buffer whereas the remainder was immobilized on the parafilm. By contrast, Brilliant Sulfaflavine displayed rapid release following square root time dependence, typical of a diffusion-controlled process. The unusual behavior of copper chlorophyllin is attributed to the presence of CuChl nanoparticles when dispersed in water. The nanoparticles are encased in the polyelectrolyte complex that adheres to parafilm. The fraction of the added copper chlorophyllin lost in the burst release can be controlled by varying the polyelectrolyte complex composition and concentration.

Development of a bioactive paper sensor for detection of neurotoxins using piezoelectric inkjet printing of sol-gel-derived bioinks.

There is an increasing interest in new strategies to rapidly detect analytes of clinical and environmental interest without the need for sophisticated instrumentation. As an example, the detection of acetylcholinesterase (AChE) inhibitors such as neurotoxins and organophosphates has implications for neuroscience, drug assessment, pharmaceutical development, and environmental monitoring. Functionalization of surfaces with multiple reagents, including enzymes and chromogenic reagents, is a critical component for the effective development of "dipstick" or lateral flow biosensors. Herein, we describe a novel paper-based solid-phase biosensor that utilizes piezoelectric inkjet printing of biocompatible, enzyme-doped, sol-gel-based inks to create colorimetric sensor strips. For this purpose, polyvinylamine (PVAm, which captures anionic agents) was first printed and then AChE was overprinted by sandwiching the enzyme within two layers of biocompatible sol-gel-derived silica on paper. AChE inhibitors, including paraoxon and aflatoxin B1, were detected successfully using this sensor by measuring the residual activity of AChE on paper, using Ellman's colorimetric assay, with capture of the 5-thio-2-nitrobenzoate (TNB(-)) product on the PVAm layer. The assay provided good detection limits (paraoxon, approximately 100 nM; aflatoxin B1, approximately 30 nM) and rapid response times (<5 min). Detection could be achieved either by eye or using a digital camera and image analysis software, avoiding the need for expensive and sophisticated instrumentation. We demonstrate that the bioactive paper strip can be used either as a dipstick or a lateral flow-based biosensor. The use of sol-gel-based entrapment produced a sensor that retained enzyme activity and gave reproducible results after storage at 4 degrees C for at least 60 days, making the system suitable for storage and use in the field.

Choosing mineral flotation collectors from large nanoparticle libraries.

Polystyrene nanoparticles can promote froth flotation of mineral particles if the nanoparticles are sufficiently hydrophobic and are colloidally stable in the high ionic strength solutions typical of commercial flotation operations. A library of 80 unique polystyrene nanoparticle types was prepared with click chemistry and used to determine if particles that were sufficiently hydrophilic to be colloidally stable in high ionic strength and high pH solutions, were also capable of promoting flotation. The conflicting requirements of colloidal stability and hydrophobicity can be achieved in 9 mM sodium carbonate, a very challenging environment. Instead of testing all 80 samples with laborious flotation testing, automated assays measuring colloid stability and nanoparticle hydrophobicity were employed. The colloid stability assay measured the critical coagulation concentrations (CCC). Nanoparticle hydrophobicity was characterized by water contact angle, measurements (CA). A smaller cohort of the most promising nanoparticle candidates for detailed flotation testing were identified by mapping nanoparticle properties on the CA versus CCC plain - a "Flotation Domain Diagram". We believe that this work was the first time that combinatorial synthesis and high throughput screening have been used in the development of flotation chemicals. Finally, based on the accumulated evidence, effective nanoparticle flotation collectors are likely to be ∼50 nm in diameter, with a soft hydrophobic polymer shell and with surface functional group densities in the order of magnitude of 0.1 nm-2.

Hydrazide-Derivatized Microgels Bond to Wet, Oxidized Cellulose Giving Adhesion Without Drying or Curing.

Hydrazide-derivatized poly(N-isopropylacrylamide-co-acrylic acid) microgels gave strong adhesion to wet, TEMPO oxidized, regenerated cellulose membranes without a drying or heating step. Adhesion was attributed to hydrazone covalent bond formation with aldehyde groups present on the cellulose surfaces. This is one of only three chemistries we have found that gives significant never-dried adhesion between wet cellulose surfaces. By contrast, for cellulose joints that have been dried and heated before wet testing, the hydrazide-hydrazone chemistry offers no advantages over standard paper industry wet strength resins. The design rules for the hydrazide-microgel adhesives include: cationic microgels are superior to anionic gels; the lower the microgel cross-link density, the higher the adhesion; longer PEG-based hydrazide tethers offer no advantage over shorter attachments; and, adhesion is independent of microgel diameter. Many of these rules were in agreement with predictions of a simple adhesion model where the microgels were assumed to be ideal springs. We propose that the unexpected, high cohesion between neighboring microgels in multilayer films was a result of bond formation between hydrazide groups and residual NHS-carboxyl esters from the preparation of the hydrazide microgels.

Redox Properties of Polyvinylamine-g-TEMPO in Multilayer Films with Sodium Poly(styrenesulfonate).

Layer-by-layer (LbL) assemblies of polyvinylamine with grafted TEMPO moieties (PVAm-T) with sodium polystyrenesulfonate (PSS) were prepared on gold-sulfonate surfaces, and the redox properties were measured by cyclic voltammetry. LbL compositions were probed by quartz crystal microbalance (wet) and ellipsometric (dry) film measurements. Approximately 30% of the TEMPO moieties in the LbL assemblies were redox-active when the total TEMPO coverage was varied up to 6 µmol/m2, by either varying the TEMPO content in PVAm-T or by varying the number of LbL bilayers. Three non-redox-active PVAm/PSS blocking bilayers were required to prevent the electrode from oxidizing PVAm-T in the exterior LbL layer. This suggests significant intermixing between the layers in the LbL film. In addition to contributing to the small but growing body of work on redox polymers based on grafted TEMPO, this work serves as a reference point for understanding the redox properties of colloidal PVAm-T-laccase complexes in future work.

Automating multi-step paper-based assays using integrated layering of reagents.

We describe a versatile and simple method to perform sequential reactions on paper analytical devices by stacking dry pullulan films on paper, where each film contains one or more reagents or acts as a delay layer. Exposing the films to an aqueous solution of the analyte leads to sequential dissolution of the films in a temporally controlled manner followed by diffusive mixing of the reagents, so that sequential reactions can be performed. The films can be easily arranged for lateral flow assays or for spot tests (reactions take place sequentially in the z-direction). We have tested the general feasibility of the approach using three different model systems to demonstrate different capabilities: 1) pH ramping from low to high and high to low to demonstrate timing control; 2) rapid ready-to-use two-step Simon's assays on paper for detection of drugs of abuse utilizing a 2-layer stack containing two different reagents to demonstrate the ability to perform assays in the z-direction; and 3) sequential cell lysing and colorimetric detection of an intracellular bacterial enzyme, to demonstrate the ability of the method to perform sample preparation and analysis in the form of a spot assay. Overall, these studies demonstrate the potential of stacked pullulan films as useful components to enable multi-step assays on simple paper-based devices.

Simple and ultrastable all-inclusive pullulan tablets for challenging bioassays.

Many biodetection systems employ labile enzymes and substrates that need special care, making it hard to routinely use them for point-of-care or field applications. In this work we provide a simple solution to this challenging problem through the creation of all-inclusive pullulan assay tablets. The proposed tablet system not only enhances the long-term stability of both enzymes and organic substrates, but also simplifies the assay procedure. The enhanced stability is attributed to two factors: the restriction of the molecular motion of proteins and impermeability to molecular oxygen afforded by the tables. These tablets dissolve rapidly upon addition to testing samples, making the test very easy to perform. Using the ATP-detecting luciferase-luciferin system as an example, we show that the tablet-based assay can achieve highly sensitive detection of ATP in biological samples and that the activity of the assay tablets remains unchanged for over a month at room temperature.

Towards high throughput screening of nanoparticle flotation collectors.

To function as flotation collectors for mineral processing, polymeric nanoparticles require a delicate balance of surface properties to give mineral-specific deposition and colloidal stability in high ionic strength alkaline media, while remaining sufficiently hydrophobic to promote flotation. Combinatorial nanoparticle surface modification, in conjunction with high throughput screening, is a promising approach for nanoparticle development. However, efficient automated screening assays are required to reject ineffective particles without having to undergo time consuming flotation testing. Herein we demonstrate that determining critical coagulation concentrations of sodium carbonate in combination with measuring the advancing water contact angle of nanoparticle-saturated glass surfaces can be used to screen ineffective nanoparticles. Finally, none of our first nanoparticle library based on poly(ethylene glycol) methyl ether methacrylate (PEG-methacrylate) were effective flotation collectors because the nanoparticles were too hydrophilic.

Design Rules for Fluorocarbon-Free Omniphobic Solvent Barriers in Paper-Based Devices.

The utility of hydrophobic wax barriers in paper-based lateral flow and multiwell devices for containment of aqueous solvents was extended to organic solvents and challenging aqueous surfactant solutions by preparation of a three layer barrier, consisting of internal pullulan impregnated paper barriers surrounded by external wax barriers. When paper impregnated with pullulan solution dries, the polymer forms solvent blocking lenses in the paper structure. Lens formation was illustrated by forming pullulan lenses in glass capillaries. The lens shapes were less curved compared to the predictions of a model based upon minimizing surface area. For barriers on Whatman # 1 filter paper, the pullulan molecular weight must be greater than ∼70 kDa, the mass fraction of pullulan in the barrier zone must be at least 32%, and there are restrictions on the minimum width of the pullulan impregnated zone.