Influence of the biomechanical evaluation of rupture using two shapes of same intramedullary implant after proximal interphalangeal joint arthrodesis to correct the claw/hammer pathology: A finite element study.

We used finite element analysis to study the mechanical stress distribution of a new intramedullary implant used for proximal interphalangeal joint (PIPJ) arthrodesis (PIPJA) to surgically correct the claw-hammer toe deformity that affects 20% of the population. After geometric reconstruction of the foot skeleton from claw toe images of a 36-year-old male patient, two implants were positioned, in the virtual model, one neutral implant (NI) and another one 10° angled (10°AI) within the PIPJ of the second through fourth HT during the toe-off phase of gait and results were compared to those derived for the non-surgical foot (NSF). A PIPJA was performed on the second toe using a NI reduced tensile stress at the proximal phalanx (PP) (45.83 MPa) compared to the NSF (59.44 MPa; p < 0.001). When using the 10°AI, the tensile stress was much higher at PP and middle phalanges (MP) of the same toe, measuring 147.58 and 160.58 MPa, respectively, versus 59.44 and 74.95 MPa at corresponding joints in the NSF (all p < 0.001). Similar results were found for compressive stresses. The NI reduced compressive stress at the second PP (-65.12 MPa) compared to the NSF (-113.23 MPa) and the 10°AI (-142 MPa) (all p < 0.001). The von Mises stresses within the implant were also significantly lower when using NI versus 10°AI (p < 0.001). Therefore, we do not recommend performing a PIPJA using the 10°AI due to the increase in stress concentration primarily at the second PP and MP, which could promote implant breakage.

Effects of different switched or not-switched implant and abutment platform designs and marginal bone loss on fracture strength: An in vitro study.

STATEMENT OF PROBLEM: The use of reduced platform sets (implants and abutments) can help to control crestal bone loss around implants, which is essential for optimizing esthetics and biomechanical behavior. However, the information available on the fracture resistance of implants with a reduced platform is sparse. PURPOSE: The purpose of this in vitro study was to analyze the maximum fracture strength value of implants with different platform designs during quasistatic fatigue, followed by a simulation of different bone levels of cervical insertion. MATERIAL AND METHODS: One hundred and twenty sets of dental implants and abutments with different diameters and platform designs were tested. All implants had an internal hexagon connection and conical macrogeometry. Four groups (n=30) were studied: Ø4.0-mm implants with a regular matched platform (rMatch group), Ø4.0-mm implants with a regular switched platform (PSwitch group), Ø5.0-mm implants with a wide matched platform (wMatch group), and Ø5.0-mm implants with a wide switched platform (wSwitch group). Three conditions simulating different levels of bone position around the cervical portion of the implants were proposed: insertion at the implant shoulder level=0 mm (L0), level=3 mm of insertion loss (L3), and level=5 mm of insertion loss (L5). All sets of all groups and proposed insertion level were subjected to a fracture strength test at 30 degrees in relation to the axis of the sets in a universal testing machine. RESULTS: Regardless of the insertion levels tested, the switched platform implants (rSwitch and wSwitch groups) showed similar mean fracture strength values (P>.05), while the implants of matched platforms (rMatch and wMatch groups) showed different fracture strength values for all insertion levels tested (P<.001). CONCLUSIONS: The fracture strength values of the switched platform implants were lower at all insertion levels tested. However, for all insertion levels tested, the implants with a switched platform presented less deformation, whereas, in the matched platform implants, there was significant deformation of the implant structure.

Retracted: Histologic evaluation of new bone in post-extraction sockets induced by melatonin and apigenin: an experimental study in American fox hound dogs.

OBJECTIVE: The aim of this study was to evaluate the effect of topical applications of melatonin and apigenin (4',5,7-trihydroxyflavone) on new bone formation in post-extraction sockets after 30, 60 and 90 days. MATERIALS AND METHODS: Six American fox hounds were used in the study, extracting mandibular premolars (P2, P3 and P4) and first molar (M1). Melatonin or apigenin impregnated in collagen sponges were applied at P3, P4 and M1 sites in both hemimandibles; P2 sites were used as control sites. Bone biopsies were taken at 30, 60 and 90 days and stained with hematoxylin-eosin. RESULTS: At 30 days, a higher percentage of immature bone was observed in the control group (58.11 ± 1.76%) than in the apigenin (34.11 ± 1.02%) and melatonin groups (24.9 ± 0.14%) with significant differences between the three groups (P < 0.05). At 60 days, results were significantly better at melatonin sites (10.34 ± 1.09%) than apigenin (19.22 ± 0.35%) and control sites (36.7 ± 1.11%) (P < 0.05). At 90 days, immature bone percentages were similar for all groups. New bone formation was higher in melatonin group (79.56 ± 1.9%) than apigenin (68.89 ± 1.5%) and control group (58.87 ± 0.12%). CONCLUSIONS: Topical applications of either melatonin or apigenin have a potential to accelerate bone tissue in early healing stages; melatonin was seen to have stimulated bone maturation to a greater extent at the 60 days of follow-up.

Effects of Surface Treatment Modification and Implant Design in Implants Placed Crestal and Subcrestally Applying Delayed Loading Protocol.

OBJECTIVES: The aim of this study is to evaluate the effect of the surface modification and cervical implant design on the bone remodeling in implants installed at the crestal and subcrestal bone level. METHODS: Ten American Fox Hound of approximately 1 year of age, each weighing approximately 14 to 15 kg, were used for this study. Two different dental implant macrodesign were used: cylindric-conical with 3.5 mm of diameter and 9 in length (implant A) and conical with 2.9 mm of diameter and 9 mm in length (implant B). Two surfaces were used: sandblasting and acid etching (surface 1) and sandblasting and acid etching, then maintained in an isotonic solution of 0.9% sodium chloride (surface 2). Four groups were performed (n = 20 implants): Group A1 (implant A with the surface 1), Group A2 (implant A with surface 2), Group B1 (implant B with surface 1), and Group B2 (implant B with surface 2). The mandibular premolars and molars (P1, P2, P3, M1) were removed and, after 2 months of healing, implants were inserted at the crestal and 2 mm subcrestal position related to the buccal bone level. Analysis was performed at 4 and 8 weeks. Histomorphometry with longitudinal measurements and bone implant contact, bone remodeling and implant stability quotient analysis were realized. RESULTS: The surface 2 showed to get more close contact between implant and new bone formed after implant placement and more stability surrounding platform both at 4 and 8 weeks. Surface 2 groups and subrestally placed showed to have better results in terms of linear measurements, with less bone loss and soft tissue distance to the IS. The data showed significant differences among the groups (P < 0.001). CONCLUSIONS: Surface modification (surface 2) has shown to be an effective alternative to conventional surface with better results in situations placed subcrestally and combined with implant design.

Anterior loop of the mental nerve, mental foramen and incisive nerve emergency: tridimensional assessment and surgical applications.

PURPOSE: The aim of this study was to investigate the prevalence and length of the anterior loop (AL), the distance from this landmark to the alveolar crest and its relation with the shape of the foramen and emergency pattern in the Spanish population on helical computed tomography scan (helical CT scan) through tridimensional reconstructions. METHODS: Helical CT scan images of 41 patients aged 65 or older were analyzed. A total of 82 human hemi-mandibles were examined in this study. A tridimensional reconstruction of each mandible and Inferior Alveolar Nerve canal was created in AMIRA® software (AMIRA, Mercury Computer Systems, Berlin, Germany). Prevalence, length and distance between the AL, mental foramen and alveolar ridge were measured. This retrospective observational study was performed according to the STROBE guidelines. RESULTS: Prevalence of the AL was 53.7 % (n = 44) and the mean length was 1.3 ± 0.64 mm. The mean distance from the highest point of the loop to the alveolar ridge was 13.4 ± 2.8 mm. The mean diameter of the mental foramen was 3.5 ± 0.65 mm and the proportion of the oval-shaped was 62.2 % (n = 51) and round-shaped was 37.8 % (n = 31). The study found that patients with type 1 pattern emergency pattern had a higher prevalence of the AL (p = 0.03). CONCLUSIONS: Prevalence, location and length of the anterior loop can be overlooked if only two-dimensional pre-surgical studies are performed. Therefore, three-dimensional imaging and modeling of anatomic structures should be used for the pre-operative examination of the interforaminal area. Given the wide variability of the emergency pattern of the mental nerve and the prevalence and location of the anterior loop, it should be studied in every patient individually.

In situ antimicrobial activity on oral biofilm: essential oils vs. 0.2 % chlorhexidine.

OBJECTIVES: This study aims to evaluate the in situ antibacterial activity of a mouthwash containing essential oils (M-EO) on undisturbed de novo plaque-like biofilm (PL-biofilm) up to 7 h after its application. PATIENTS AND METHODS: An appliance was designed to hold six glass disks on the buccal sides of the lower teeth, allowing PL-biofilm growth. Fifteen healthy volunteers wore the appliance for 48 h and then performed a M-EO. Disks were removed after 30 s and at 1, 3, 5, and 7 h later. After a washout period, the same procedure was repeated with a M-WATER and a M-0.2 % chlorhexidine. After PL-biofilm vital staining, samples were analyzed using a confocal laser scanning microscope. RESULTS: At 30 s after M-EO, the levels of bacterial vitality were 1.18 %, significantly lower than that of the basal sample (p < 0.001). After 7 h, the antibacterial effect of essential oils was still patent with a 47.86 % difference in bacterial vitality compared to the basal sample (p < 0.001). CONCLUSION: A single M-EO presents high antibacterial immediate activity and penetration capacity in situ and a substantivity which lasts for at least 7 h after its application over de novo biofilm. These results were better than those observed with 0.2 % chlorhexidine under the same conditions. CLINICAL RELEVANCE: A single M-EO is an effective measure against the de novo biofilm, presenting a good alternative to clorhexidine such as a preoperative rinse, in periodontal procedures or post-treatment applications.

State anxiety and depression as factors modulating and influencing postoperative pain in dental implant surgery. A prospective clinical survey.

OBJECTIVES: To determine whether preoperative state anxiety and depression modulate or influence objective and subjective postoperative pain following dental implant insertion. STUDY DESIGN: Prospective, clinical study with 7-day follow-up of a sample of 105 subjects who preoperatively completed the state anxiety questionnaire (STAI-E) and Beck Depression Inventory (BDI) and postoperatively, at 2 and 7 days, recorded objective pain with the Semmes-Weinstein mechanical esthesiometer (SW test) and subjective pain with the Visual Analog Scale (VAS). RESULTS: 85.6% and 81.5% of patients, respectively, recorded no signs of state anxiety or depression. The correlation between anxiety and depression for both maxillary bones was the lower (P=0.02). The correlation between subjective and objective pain at 2 and 7 days, and the anatomic regions intervened, was statistically significant in the mandible at day 7 (P<0.01), and highly significant (P<0.001) for the other variables. The correlation between state anxiety and objective pain at day 7 was nearly statistically significant (P=0.07). CONCLUSIONS: The correlation between state anxiety and depression, and objective and subjective pain at day 7 was not statistically significant. A strong correlation was found between objective and subjective pain in the immediate postoperative period.

Mechanical Behavior of Five Different Morse Taper Implants and Abutments with Different Conical Internal Connections and Angles: An In Vitro Experimental Study.

The present study evaluated the mechanical behavior of five designs of Morse taper (MT) connections with and without the application of loads. For this, the detorque of the fixing screw and the traction force required to disconnect the abutment from the implant were assessed. A total of 100 sets of implants/abutments (IAs) with MT-type connections were used, comprising five groups (n = 20/group): (1) Group Imp 11.5: IA sets with a cone angulation of 11.5°; (2) Group SIN 11.5: with a cone angulation of 11.5°; (3) Group SIN 16: with a cone angulation of 16°; (4) Group Neo 16: with a cone angulation of 16°; and (5) Group Str 15: with a cone angulation of 15°. All sets received the torque recommended by the manufacturer. After applying the torque, the counter torque of the fixing screws was measured in ten IA sets of each group without the application of cyclic loads (frequencies ≤ 2 Hz, 360,000 cycles, and force at 150 Ncm). The other ten sets of each group were subjected to cyclic loads, after which the detorque was measured. Afterwards, the force for disconnection between the implant and the abutment was measured by traction on all the samples. The untwisting of the abutment fixation screws showed a decrease in relation to the initial torque applied in all groups. In the unloaded samples, it was found to be -25.7% in Group 1, -30.4% in Group 2, -36.8% in Group 3, -29.6% in Group 4, and -25.7% in Group 5. After the applied loads, it was found to be -44% in Group 1, -43.5% in Group 2, -48.5% in Group 3, -47.2% in Group 4, and -49.8% in Group 5. The values for the IA sets were zero for SIN 16 (Group 3) and Neo16 (Group 4), both without and with loads. In the other three groups, without loads, the disconnection value was 56.3 ± 2.21 N (Group 1), 30.7 ± 2.00 N (Group 2), and 26.0 ± 2.52 N (Group 5). After applying loads, the values were 63.5 ± 3.06 N for Group 1, 34.2 ± 2.45 N in Group 2, and 23.1 ± 1.29 N in Group 5. It was concluded that in terms of the mechanical behavior of the five designs of MT IA sets, with and without the application of loads, the Imp 11.5, SIN 11.5, and Srt 15 groups showed better results compared to the SIN 16 and Neo 16 groups, showing that lower values of cone angulation increase the friction between the parts (IA), thus avoiding the need to maintain the torque of the fixing screw to maintain the union of the sets.

Fibroblasts and osteoblasts behavior after contact with different titanium surfaces used as implant abutment: An in vitro experimental study.

Background: The goal of this in vitro study was to compare three different surfaces: two types of implant surfaces commercially available ([a] smooth/machined and [b] acid-treated surface) versus (c) anodized surface. Discs were manufactured with commercially pure titanium (CP) grade IV, which were subsequently analyzed by scanning microscopy and fibroblastic and osteoblastic cell cultures. Methods: Ninety-nine discs (5 × 2 mm) were manufactured in titanium grade IV and received different surface treatments: (i) Mach group: machined; (ii) AA group: double acid etch; and (iii) AN group: anodizing treatment. Three discs from each group were analyzed by Scanning Electron Microscopy (SEM) to obtain surface topography images and qualitatively analyzed by EDS. Balb/c 3T3 fibroblasts and pre-osteoblastic cells (MC3T3-E1 lineage) were used to investigate each group's biological response (n = 10/cellular type). The data were compared statistically using the ANOVA one-way test, considered as a statistically significant difference p < 0.05. Results: The AA group had numerous micropores with diameters between 5 and 10 µm, while nanopores between 1 and 5 nm were measured in the AN group. The EDX spectrum showed a high titanium concentration in all the analyzed samples. The contact angle and wetting tension were higher in the AA, whereas similar results were observed for the other groups. A lower result was observed for base width in the AA, which was higher in the other two groups. The AN showed the best values in the fibroblast cells, followed by Mach and AA; whereas, in the culture of the MC3T3 cells, the result was precisely the opposite (AA > Mach > AN). There was similar behavior for cell adhesion for the test groups (Mach and AN), with greater adhesion of Balb/c 3T3 fibroblasts compared to MC3T3 cells; in the AA group, there was greater adherence for MC3T3 cells compared to Balb/c 3T3 fibroblasts. Conclusions: The findings suggest that different surface characteristics can produce different biological responses, possibly cell-line dependent. These findings have important implications for the design of implantable medical devices, where the surface characteristics can significantly impact its biocompatibility.

Infant growth patterns of the mandible in modern humans: a closer exploration of the developmental interactions between the symphyseal bone, the teeth, and the suprahyoid and tongue muscle insertion sites.

The ontogenetic development of the mental region still poses a number of unresolved questions in human growth, development and phylogeny. In our study we examine the hypotheses of DuBrul & Sicher (1954) (The Adaptive Chin. Springfield, IL: Charles) and Enlow (1990) (Facial Growth, 3rd edn. Philadelphia, PA: Saunders) to explain the presence of a prominent mental region in anatomically modern humans. In particular, we test whether the prominence of the mental region and the positioning of the teeth are both correlated with the developmental relocation of the tongue and the suprahyoid muscles inserting at the lingual side of the symphysis. Furthermore, we test whether the development of the mental region is associated with the development of the back of the vocal tract. Using geometric morphometric methods, we measured the 3D mandibular and tooth surfaces in a cross-sectional sample of 36 CT-scanned living humans, incorporating the positions of the tongue and the geniohyoid and digastric muscle insertions. The specimens' ages range from birth to the complete emergence of the deciduous dentition. We used multivariate regression and two-block partial least squares (PLS) analysis to study the covariation among the mental region, the muscle insertions, and the teeth both across and within age stages. In order to confirm our results from the 3D cross-sectional sample, and to relate them to facial growth and the position of the cervical column and the hyoid bone, we used 46 lateral radiographs of eight children from the longitudinal Denver Growth Study. The 3D analysis demonstrates that the lingual side of the lower border of the symphysis develops downwards and forwards. These shape changes are significantly correlated with the relocation of muscle insertion sites and also with the vertical reorientation of the anterior teeth prior to emergence. The 2D analysis confirms the idea that as the mental region prominence develops, the space of the laryngopharynx becomes restricted due to upper mid-face retraction and the acquisition of upright body posture. In agreement with the hypotheses of DuBrul & Sicher (1954) and Enlow (1990), our results suggest that the presence of a prominent mental region responds to the space restriction at the back of the vocal tract, and to the packaging of the tongue and suprahyoid muscles in order to preserve the functionality of the laryngopharynx during respiration, feeding and speech.

Biomechanical evaluation of abutment stability in morse taper implant connections in different times: A retrospective clinical study compared with an in vitro analysis.

Objectives: Micromotion between a dental implant and abutment can adversely affect clinical performance and compromise successful osseointegration by creating a bacterial harbor, enabling screw loosening, and imparting disruptive lateral forces on the cortical bone. Thus, the aim of the present study was to measure the abutment stability evolution using resonance frequency analysis (RFA) in vivo at four different times (baseline, 3, 4, and 12 months), and compare these data obtained with the RFA measured after mechanical cycling (in vitro) corresponding to the proposed times in numbers of cycles. Methods: To evaluate the abutment stability, RFA was performed in 70 sets of implant/abutment (IA) with a total of 54 patients (31 women, 23 men). These IA sets were divided into three groups, according to the abutment angulation: straight abutment (Abt1 group), 17-degree angled abutment (Abt2 group), and 30-degree angled abutment (Abt3 group). Abutment stability was measured immediately at implant placement and the abutment installation (T1), 3 (T2), 4 (T3), and 12 months (T4) later. For the in vitro analysis, ten sets of each group were submitted to mechanical cycling: T1 = 0 cycles, T2 = 90,000 cycles, T3 = 120,000 cycles, and T4 = 360,000 cycles. All data collected were statistically evaluated using the GraphPad Prism 5.01 software, with the level of significance was α = 0.05. Results: In vivo, the overall data of implant stability quotient (ISQ) values obtained for all groups in each evaluation time were 61.5 ± 3.94 (95% CI: [60-63]) at T1, 62.8 ± 3.73 (95% CI, [61-64]) at T2, 63.4 ± 3.08 (95% CI: [61-64]) at T3, and 65.5 ± 4.33 (95% CI: [63-68]) at T4. Whereas in vitro, the ISQ were 61.5 ± 2.66 (95% CI: [59-63]) at T1, 63.2 ± 3.02 (95% CI, [61-65]) at T2, 63.9 ± 2.55 (95% CI: [62-66]) at T3, and 66.5 ± 2.97 (95% CI: [64-68]) at T4. In both evaluations (in vivo and in vitro), the data showed a significant difference (ANOVA test with p < 0.0001). Conclusions: The RFA to measure the abutment stability used in this study showed that there was a progressive increase in stability among the predetermined times for the measurements, in both analysis (in vivo and in vitro). Furthermore, the values at each time point were similar, with no statistical difference between them.

Anatomical association between wrist extensor musculature and topographical pain sensitivity maps of the elbow area.

OBJECTIVE: High-density topographical sensitivity maps have been developed to visualize nonuniformity deep tissue pain sensitivity in, for example, lateral epicondylitis (LE). The aim of this cadaveric study was to determine the anatomical association between the topographical sensitivity maps over the elbow area and wrist extensor musculature. METHODS: A topographical pressure sensitivity map consisting of 12 points forming a 3 × 4 matrix: 4 points in the superior part, 4 points in the middle, and 4 points in the lower part around the lateral epicondyle was marker on a 50-year embalmed cadaver. Color marker pins were inserted into each point. Pins were removed during the process of dissection, but the small holes created by their removal assured accurate relocation. RESULTS: Progressive dissection revealed that points 1 to 4 (superior line) were placed over the musculotendinous junction and belly of the extensor carpi radialis brevis (ECRB) muscle, points 6 to 8 (middle line) were placed over the musculotendinous junction and belly of the extensor digitorum communis muscle, and points 9 to 12 (inferior line) were located over the musculotendinous junction and belly of the extensor carpi ulnaris muscle. It was also observed that the superficial branch of the radial nerve runs between the belly of the ECRB and extensor digitorum communis muscles. CONCLUSIONS: This study confirmed that anatomical location previously assumed supporting the important wrist extensor muscles, particularly the ECRB, in patients with LE as depicted by pressure pain sensitivity maps. This study also suggests a potential role of the superficial branch of the radial nerve in LE.

Are Panoramic Images a Good Tool to Detect Calcified Carotid Atheroma? A Systematic Review.

To investigate the reliability of panoramic dental images to detect calcified carotid atheroma, electronic databases (PubMed, IEEE/Xplore and Embase) were searched. Outcomes included cerebrovascular disease events, cardiovascular disease events, patient previous diseases, and combined endpoints. Risk of bias was evaluated using the Newcastle-Ottawa Scale. Hence, 15 studies were selected from 507 potential manuscripts. Five studies had a low risk of bias, while the remaining nine studies were found to have a moderate risk. Heterogeneous results were obtained but showed that patients with risk factors, such as obesity, diabetes mellitus, hypertension, and smoking, and with calcified carotid atheroma on panoramic images, have a higher prevalence than healthy patients. The evidence in the literature was found to be equivocal. However, the findings of this systematic review exhibit that panoramic radiographs can be used for dental diagnosis and treatment planning, as well as to detect calcified carotid artery atheroma.

Vertical bone augmentation with 3D-synthetic monetite blocks in the rabbit calvaria.

INTRODUCTION: Long-term success of osteointegrated dental implants requires sufficient volume of healthy bone at the recipient sites. However, this is frequently lacking as a result of trauma, tooth loss, or infection. Onlay autografting is amongst the most predictable techniques for craniofacial vertical bone augmentation, however, complications related to donor site morbidity are common and alternatives to onlay autografts are desirable. AIM: To develop and evaluate a new synthetic onlay block for vertical bone augmentation. MATERIAL AND METHODS: Sixteen synthetic monetite monolithic discs-shaped blocks were prepared using a 3D-printing technique. The blocks were computer-designed, and had a diameter of 9.0 mm, a thickness of either 4.0 mm (n = 8) or 3.0 mm (n = 8) and one 0.5-mm wide central hole that enabled their surgical fixation with osteosynthesis screws. The blocks were randomly allocated to each side of the calvaria (right or left) of eight New Zealand rabbits and fixed with screws to achieve vertical bone augmentation. Eight weeks after the surgical intervention, the animals were sacrificed and the calvaria were retrieved for histological analysis. The following parameters were analysed: the interaction between the graft and the original bone surface, the amount of bone ingrowth within the graft and the gain in bone height achieved by the procedure. Wilcoxon t-test was used to evaluate significant differences between the two types of monetite bone block grafts. RESULTS: The blocks were easy to handle and no damage or fracture was registered while being screw-fixated to the calvarial bone. As a result, the surgical procedure was easy and quick. After a healing of 8 weeks, the synthetic blocks were strongly fused to the calvarial bone surface. Upon histological observation, the monetite blocks appeared to be infiltrated by newly formed bone, without histological signs of necrosis, osteolysis or foreign body reaction. Histomorphometry revealed that bone augmentation occurred within and over the monetite block. The 4.0- and 3.0-mm high blocks were filled with newly formed bone with 35% and 41% of their respective volumes. These observations indicated that craniofacial bone augmentations of at least 4 mm could be achieved with synthetic monetite blocks. CONCLUSION: Within the limits of our study, this novel material may be able to eliminate the need for autologous bone transplantation for the augmentation of large vertical bone defects.

Evaluation of the Efficacy of Lacer HaliTM Treatment on the Management of Halitosis: A Randomized Double-Blind Clinical Trial.

BACKGROUND: Halitosis of oral origin is very common in the general population. Due to their antimicrobial properties, chlorhexidine-based products are widely used in the management of this condition, but these are associated with reversible side effects. In this study we evaluated the efficacy of Lacer HaliTM mouthrinse and toothpaste in subjects with intraoral halitosis after several applications under normal conditions of use. METHODS: In this randomized clinical trial with mouth rinse and toothpaste, single-center, double-blinded, parallel participants were assigned to an experimental group (Lacer HaliTM,, n = 20), a positive control group (HalitaTM, n = 20), and a placebo group (n = 20). The active duration of the study was 18 days. The clinical follow-up evaluations were performed at five time points (T0, T1, T2, T3, and T4). The intensity of halitosis was evaluated by organoleptic measurement and the portable gas chromatograph OralChromaTM. The data were analyzed using generalized mixed linear models. RESULTS: Sixty patients completed the study. Lacer HaliTM, in comparison with HalitaTM, did not show statistically significant differences at any time during the study except for the levels of hydrogen sulfide and total volatile sulfur compounds at 15 days, where HalitaTM was better. Compared to the placebo treatment, Lacer HaliTM, was significantly more efficient, in terms of both the organoleptic evaluations at 8 days and the levels of hydrogen sulfide. CONCLUSIONS: Lacer HaliTM is an alternative to chlorhexidine-based toothpaste and mouthwashes in the management of halitosis.

Clinical Behavior and Complications of Mandibular Full-Arch Fixed Dental Prostheses Supported by Three Dental Implants. A Systematic Review and Meta-Analysis.

This systematic review and meta-analysis set out to assess the clinical behavior of mandibular implant-supported fixed complete dental prostheses (ISFCDP) on three dental implants by analyzing implant and prosthetic survival rates, marginal bone loss, biological/technical complications, and patient-reported outcomes. The review was conducted according to PRISMA guidelines. Electronic searches were conducted in the Medline (PubMed), Web of Science, and Cochrane databases, complimented by a manual search in specialist journals for relevant articles published up to February 2021. The Newcastle-Ottawa Quality Assessment Scale tool was used to assess the quality of evidence in the studies reviewed. The study included 13 articles with 728 patients treated with 2184 implants. A mean implant survival rate of 95.9% (95% CI: 94.6-97.3%) and a prosthetic survival rate of 97.0% (95% CI: 95.7-98.3%) were obtained over 1-6-year follow-up periods. Mandibular implant-supported fixed complete dental prostheses on three dental implants would appear to be a viable option for restoring the edentulous mandible in comparison with mandibular ISFCDP on more than three implants. Further comparative studies are needed, with adequate protocols, as well as sufficient sample sizes and follow-up periods to confirm these findings.

Long-Term Clinical Behavior and Complications of Intentionally Tilted Dental Implants Compared with Straight Implants Supporting Fixed Restorations: A Systematic Review and Meta-Analysis.

The aim of this study was to assess the long-term clinical behavior of straight implants in comparison with intentionally tilted dental implants (ITDI) supporting fixed restorations in partial or total edentulous arches, analyzing implant survival and success rates, complications, and marginal bone loss (MBL) after >5 years of function. An electronic search was conducted in five electronic databases (MEDLINE/Pubmed, Embase, Web of Science, Scopus, and Cochrane Central Register of Controlled Trials) supplemented by a manual search. The electronic and manual search identified 1853 articles, of which 8 articles were selected for analysis. Out of a total of 3987 dental implants, 2036 were axial dental implants and 1951 tilted. Similar results were found in implant survival or overall implant success rates. Moreover, no statistically significant differences were found in MBL (p = 0.369; MD 0.116 mm (-0.137; 0.369) 95% CI) The prosthodontic/biological complications reported in the articles were very diverse and irregularly distributed. This systematic review suggests that there is no difference between tilted compared with straight dental implants in the medium-long term (>5 years). However, further research is needed to generate long-term data and confirm the present review's findings.

Sucrose Is Not the Whole Story: Risk Factors and Oral Health at the Contact (Yakutia, Siberia-16th/19th).

(1) Background: contact between indigenous and European populations has often resulted in changes in oral health attributed to the introduction of sucrose. Most studies are per tooth over considerable periods and with few ethnological references. (2) Aim: dental epidemiology of 96 autochthonous frozen bodies from Yakutia between the early 17th century and the late 19th century; comparisons with historical texts and ethnographic data. (3) Material and methods: we use descriptive statistics and discriminant factorial analyses to identify dominant variables in the dataset and compare periods and subjects, considering all variables. (4) Results: the peculiarities of the population are the rarity of cavities and the relative frequency of dental pathologies leading to death. Assimilation into the Russian Orthodox culture has led to decreased tooth wear and an increase in tooth loss. Dental health evolves only two centuries after the contact. (5) Conclusions: the confrontation with historical data suggests that changes are not related to the growing importance of sucrose but to a combined action: the substitution of dendrophagy by cereal flour; the decrease in immunity linked to the development of chronic infectious diseases; tobacco addiction and the mandibular torus: a risk factor promoting apical cysts.

Platelet-rich plasma may prevent titanium-mesh exposure in alveolar ridge augmentation with anorganic bovine bone.

OBJECTIVE: Bone augmentation with the titanium-mesh (Ti-mesh) technique is susceptible to a large rate of complications such as morbidity of bone graft donor site, and mesh exposure to the oral cavity. The purpose of this study was to evaluate the effectiveness of anorganic bovine bone (ABB) in alveolar bone augmentation with the Ti-mesh technique. In addition, we investigated the effect of platelet-rich plasma (PRP) in preventing mesh exposure by using it to cover the Ti-mesh. PATIENTS AND METHODS: Patients included in the clinical trial were randomly allocated by a blinded assistant into two groups. The 30 patients recruited for this study underwent 43 alveolar bone augmentation with the Ti-mesh technique using ABB as graft material in all of them. In 15 patients, the Ti-meshes were covered with PRP (PRP group) whereas in the other 15 the Ti-meshes were not (control group). After 6 months, patients were called for clinical, radiographic, and histological evaluation, and implant placement surgery. A total of 97 implants were placed in the augmented bone and their evolution was followed up for a period of 24 months. RESULTS: Significant differences were found between the two study groups in terms of complications and bone formation. In the control group, 28.5% of the cases suffered from mesh exposure, while in the PRP group, no exposures were registered. Radiographic analysis revealed that bone augmentation was higher in the PRP group than in the control group. Overall, 97.3% of implants placed in the control group and 100% of those placed in the PRP group were successful during the monitoring period. We suggest that the positive effect of PRP on the Ti-mesh technique is due to its capacity to improve soft tissue healing, thereby protecting the mesh and graft material secured beneath the gingival tissues. CONCLUSIONS: Alveolar bone augmentation using ABB alone in the Ti-mesh technique is sufficient for implant rehabilitation. Besides, covering the Ti-meshes with PRP was a determining factor in avoiding mesh exposure. Ti-mesh exposure provoked significant bone loss, but in most cases it did not affect the subsequent placement of implants.

Advantages and drawbacks of proximal interphalangeal joint fusion versus flexor tendon transfer in the correction of hammer and claw toe deformity. A finite-element study.

Correction of claw or hammer toe deformity can be achieved using various techniques, including proximal interphalangeal joint arthrodesis (PIPJA), flexor digitorum longus tendon transfer (FDLT), and flexor digitorum brevis transfer. PIPJA is the oldest technique, but is associated with significant complications (infection, fracture, delayed union, and nonunion). FDLT eliminates the deformity, but leads to loss of stability during gait. Flexor digitorum brevis tendon transfer (FDBT) seems to be the best surgical alternative, but it is a recent technique with still limited results. In this work, these three techniques have been analyzed by means of the finite-element method and a comparative analysis was done with the aim of extracting advantages and drawbacks. The results show that the best technique for reducing dorsal displacement of the proximal phalanx is PIPJA (2.28 mm versus 2.73 mm for FDLT, and 3.31 mm for FDBT). However, the best technique for reducing stresses on phalanges is FDLT or FDBT (a reduction of approximately 35% regarding the pathologic case versus the increase of 7% for the PIPJA in tensile stresses, and a reduction of approximately 40% versus 25% for the PIPJA in compression stresses). Moreover, the distribution of stresses in the entire phalanx is different for the PIPJA case. These facts could cause problems for patients, in particular, those with pain in the surgical toe.