Reuse of polymeric waste for the treatment of marine water polluted by diesel.

Accidental diesel spills can occur in marine environments such as harbors, leading to adverse effects on the environmental compartment and humans. This study proposes the surgical mask as an affordable and sustainable adsorbent for the remediation of diesel-contaminated seawater to cope with the polymeric waste generated monthly in hospital facilities. This approach can also be helpful considering a possible future pandemic, alleviating the pressure on the waste management system by avoiding improper mask incineration and landfilling, as instead occurred during the previous COVID-19. Batch adsorption-desorption experiments revealed a complete diesel removal from seawater after 120 min with the intact laceless mask, which showed an adsorption capacity of up to 3.43 g/g. The adsorption curve was better predicted via Weber and Morris's kinetic (R2 = 0.876) and, in general, with Temkin isotherm (R2 = 0.965-0.996) probably due to the occurrence of chemisorption with intraparticle diffusion as one of the rates-determining steps. A hysteresis index of 0.23-0.36 was obtained from the desorption isotherms, suggesting that diesel adsorption onto surgical masks was faster than the desorption mechanism. Also, the effect of pH, ionic strength and temperature on diesel adsorption was examined. The results from the reusability tests indicated that the surgical mask can be regenerated for 5 consecutive cycles while decreasing the adsorption capacity by only approximately 11%.

Phenanthrene removal from a spent sediment washing solution in a continuous-flow stirred-tank reactor.

The issue of polycyclic aromatic hydrocarbons (PAHs) is widespread in marine sediments involving ecological systems and human health. Sediment washing (SW) has proven to be the most effective remediation approach for sediments polluted by PAHs, such as phenanthrene (PHE). However, SW still raises waste handling concerns due to a considerable amount of effluents generated downstream. In this context, the biological treatment of a PHE- and ethanol-containing spent SW solution can represent a highly efficient and environmentally-friendly strategy, but its knowledge is still scarce in scientific literature and no studies have so far been conducted in continuous mode. Therefore, a synthetic PHE-polluted SW solution was biologically treated in a 1 L aerated continuous-flow stirred-tank reactor for 129 days by evaluating the effect of different pH values, aeration flowrates and hydraulic retention times as operating parameters over five successive phases. A PHE removal efficiency of up to 75-94% was achieved by an acclimated PHE-degrading consortium mainly composed of Proteobacteria, Bacteroidota and Firmicutes phyla through biodegradation following the adsorption mechanism. PHE biodegradation, mainly occurring via the benzoate route due to the presence of PAH-related-degrading functional genes and a phthalate accumulation up to 46 mg/L, was also accompanied by a reduction of dissolved organic carbon and ammonia nitrogen above 99% in the treated SW solution.

Removal of emerging pollutants from the environment: From bioadsorbents to nanoparticle-based systems.

In the Call for Papers corresponding to this Virtual Special Issue (VSI), the Editors indicated that, as is well known, emerging pollutants include a variety of substances that pose remarkable risks for the environment and public health. In fact, emerging pollutants are considered a matter of concern deserving increasing efforts to elucidate their occurrence, fate, repercussions, and alternatives to their removal from the various environmental compartments where they can be found after spreading as contaminants. Also, the Editors commented that, among the various alternatives that can be considered for achieving their successful removal, some of them are based on the use of sorbent materials, and, specifically, bioadsorbents, which are attractive due to the efficacy and low cost associated with some of them. Another alternative is related to the utilization of nanoparticle-based systems, which may be considered a promising field of research in this way. In both cases, obtaining new research results, as well as designing and programming new ways of going steps ahead in the investigation of both kinds of materials, would be key objectives. According to the previous considerations, the Editors of the VSI invited researchers having new data concerning these aspects to submit manuscripts with experimental results, discussion, reflections and prospective related to their work. With the Special Issue closed, the number of submissions received was 83, with 40 high-quality works being accepted for publication, increasing the overall knowledge on this topic by providing results that we are sure will be of value for the scientific community and the society.

Exploring the effect on the environment of encapsulated micro- and nano-plastics into asphalt mastics for road pavement.

A new environmental problem is represented by the huge transformation of plastic waste released into the environment into small fragments, the so called micro- and nano-plastics, due to atmospheric phenomena. The smaller the size of the plastic fragments, the more their spreading into environmental compartments. The aim of this study is to test encapsulation into asphalt mastics of waste plastic material (WPM) as sustainable strategy to obtain road flexible pavements and to evaluate the potential release in water of micro and nano plastics. A new mastic mixing method was developed to blend the WPM with the bitumen contained into a bitumen emulsion (BE60/40) by adopting low mixing temperatures. Three different WPM contents, equal to 5, 10 and 20% by the weight of the bitumen contained in the BE60/40, were adopted to produce the mastics; the mastics' rheological properties, obtained by frequency sweep and multiple stress creep and recovery tests, were compared to those of a traditional asphalt mastic containing limestone filler. The aging of asphalt mastics was analyzed by soaking them in water and gradually lowering and raising temperature between -10 and 60 °C at predefined intervals. The addition of WPM improved greatly the asphalt mastic performance; in particular, for a WPM content of 10%, the rheological response in terms of stiffness remained unchanged after the mastic underwent thermal excursions in water. Encapsulation of micro and nano plastics into mastics reduced of more than 99% their potential water release.

Soil science and environmental research.

As indicated in the call for papers posted for this Special Issue, Soil Science deals with various environmental compartments, so it is closely related to Environmental Research. It is clear that synergisms and collaboration are keys to reach the most fruitful relations among different sciences and scientists, and especially in all that focused on the Environment. In this line, considering Soil Science, Environmental Research, and the multiple and complex eventual combinations involving them, could give new highly interesting works focused on any of the specific subjects covered, as well as on relations among these sciences. The main objective should be going further in positive interactions that could help in protecting the Environment, proposing solutions to face hazards that are drastically threatening our planet. In view of that, the Editors of this Special Issue invited researchers to submit high-quality manuscripts including new experimental data, as well as scientifically founded discussion and reflections on the matter. The VSI has received 171 submissions, with 27% of them being accepted after peer-review. The Editors think that the papers included in this VSI have high scientific value and provide scientific knowledge on the field. In this editorial piece the Editors include comments and reflections on the papers published in the SI.

The microbial world in copper sulfide flotation plants (CSFP): Novel insights into bacterial communities and their application as potential pyrite bioreagents.

Operations in copper sulfide flotation plants (CSFP) are complex and governed by several variables such as available technologies, reagents, and environmental conditions. However, few investigations are related to studying the microbial communities. These aspects provide a reason to compare the bacterial communities of two CSFP operated with freshwater (FwFlo) and seawater (SwFlo), and study whether indigenous bacteria could be used as pyrite bioreagents. Analyses were determined through next-generation sequencing by Illumina MiSeq System and conducted throughout the entire process: (i) minerals before and after grinding; (ii) final concentrate and concentrate thickener overflow; (iii) final tailings and tailings thickener overflow; and (iv) intake water. Bacterial strains from both plants were tested as potential bioreagents, given their tendency to adhere to pyrite after 5 min. In both CSFP, Proteobacteria (relative abundance from 45.48% to 79.22%), followed by Bacteroidetes (9.37%-44.7%), were the most abundant phyla. Regarding species, Algoriphagus olei (11.35%-43.52%) was present exclusively in FwFlo samples in contact with process water and absent in the mineral before grinding, where Cupriavidus metallidurans (16.05%) and Pseudomonas_uc (11.79%) predominated. In SwFlo samples, Marinobacter flavimaris (3.47%-41.1%), and GU061212-s (10.92%-27.63%), were the most abundant microorganisms. All of them were also detected in intake seawater. The strains with the highest adhesion rate (from 29.84% ± 0.14-100%) were phylogenetically identified as species of the genera Marinobacter, Pseudomonas, Idiomarina, Halomonas, Bacillus, Aerocuccus, and Peribacillus. Our results reveal that bacterial communities are critically dependent on process waters during mining activities, and our data depicted that indigenous bacteria could be used as potential pyrite bioreagents, evidenced by a high adhesion rate. It is thus possible to propose that different indigenous bacterial strains could be considered as new bioreagents to reduce the impact of conventional flotation reagents on health from an environment friendly perspective.

A novel green approach for silver recovery from chloride leaching solutions through photodeposition on zinc oxide.

Silver is extensively used in electronics, industrial catalysis, and biomedical sector owing to its enhanced physicochemical properties. E-waste recycling may contribute significantly to enhance silver recovery in the view of a circular economy and limit the depletion of mineral sources. In this scenario, hydrometallurgical routes represent the most widely used techniques for silver extraction/recovery and require strong acidic solutions, high temperatures, and multiple operating units. An alternative sustainable route for silver recovery from leaching solutions used for silver extraction in industrial applications is herein proposed for the first time. The novel green process of silver recovery is based on the UV/vis light-driven photocatalytic deposition of pure metallic silver over low-cost and non-toxic ZnO photocatalyst. In the second step, ZnO is dissolved by slight acidification and pure metallic silver is easily recovered. Low environmental impact, mild operating conditions, and economic viability are among the major perks of the new silver recovery process developed. In the view of a full-scale implementation, several operating conditions of the recovery process (i.e., photocatalyst load, starting silver concentration, type of hole scavenger and irradiation) were thoroughly investigated. A mathematical model capable of describing the system behaviour under different operating conditions was also developed and allowed to estimate unknown kinetic parameters for the Ag-photodeposition process.

Feasibility study of saffron cultivation using a semi-saline water by managing planting date, a new statement.

In the current study the possibility of saffron (Crocus sativus L.) cultivating using semi-saline water was investigated at different planting dates. The salinity of irrigation water and soil were 2.9 and 5.8 dS m-1, respectively. The results showed that saffron had an acceptable potential for cultivation using semi-saline water in saline soils. The early planting dates went through the developmental stages faster, meaning saffron corms sown in early October sprouted earlier, flowers appeared faster and fully flowering occurred earlier. Nevertheless, plant senescence was the same in all planting dates. The highest percentage of corms sprouting and flowering were obtained in the early October planting dates in both years, which were matched with canopy temperature distribution. The highest flowers weight as well as stigma fresh and dry weight were obtained on the 13 October planting date within the 3 years study reaching the maximum values during the third year. Electrolyte leakage was higher in the last planting date, while photosynthesis pigments were more in early to mid-October planting dates. These effects might be related to damage of freezing temperature to physiological processes. Shoot dry weight and water productivity were the highest in early October planting dates. The shoot biomass on October 13 planting date was enough to be considered as a new forage source in semi-saline conditions. It seems that cultivation of saffron with semi-saline water is possible by considering a proper planting date, adequate leaching requirement and accurate irrigation management.

Role of organic nanoparticles on transport and fate of various dyes in aqueous solution.

This work studies the interaction of organic nanoparticles (ON) with various dyes in aqueous solution, to elucidate the role of ON on transport and fate of dyes in the environment, and on dyes removal from wastewater. Studied dyes are Acid Red 66 (AR66), Methylene Blue (MB), Reactive Black 5 (RB5), and Reactive Violet 5 (RV5). ON are extracted from organic matter of anthropogenic origin through resuspension of its colloidal fraction, and successive filtration and dialysis of the obtained suspension. Mechanisms of interaction are investigated initially through three-dimensional excitation emission matrix (3DEEM) analysis. Obtained data indicate that dynamic interactions occur strongly between dye molecules and ON aggregates. 3DEEM spectra of mixed samples containing ON together with one of the tested dyes, present a shape similar to the one of ON alone, but each of them is characterized by specific differences in terms of peaks quenching and shift. The analysis of these singularities suggests that dye molecules are bound to the functional groups of ON through H-bonds, according to the following steps: i) dyes reach the surface of ON aggregates; ii) the molecules pass through the hydrophilic surface of ON aggregates, and reach their hydrophobic core; iii) the dyes are sequestrated into the hydrophobic core of ON aggregates. Nuclear magnetic resonance (NMR) and electron paramagnetic resonance (EPR) spectroscopies analysis confirm the formation of supramolecular aggregates with stable micellar hydrophobic structure, mainly consisting of aliphatic fractions of ON, which explain the disappearance of aromatic groups signals from dyes.

Perovskite oxide for emerging photo(electro)catalysis in energy and environment.

Using solar energy to catalyse photo-driven processes to address the energy crisis and environmental pollution plays a role in the path to a sustainable society. Many oxide-based materials, especially perovskite oxides, have been widely investigated as catalysts for photocatalysis in energy and environment because of the low-cost and earth-abundant and good performance. At this stage, there is a need to present a scientific-based evaluation of the technologies developed so far and identify the most sustainable technologies and the existing limitations and opportunities for their commercialisation. This work comprehensively investigated the outcomes using various scientometric indices on perovskite oxide-based photo(electro)catalysts for water splitting, nitrogen fixation, carbon dioxide conversion, organic pollutant degradation, current trends and advances in the field. According to the results achieved, efforts in both energy and environment based on perovskite oxides have been initiated in the 1990s and accelerated since the 2010s. China and the United States were identified as the most contributing countries. Based on the results achieved in this study, the main milestones and current trends in the development of this field have been identified. The aim of this research is to provide useful guidelines for the further investigation of perovskite oxide-based catalysts for photoelectrocatalysis and photocatalysis both in energy and environment on the applications such as water splitting, nitrogen fixation, carbon dioxide conversion, and wastewater treatment.

New trends on green energy and environmental technologies, with special focus on biomass valorization, water and waste recycling: editorial of the special issue.

In this editorial piece, the Editors of the Virtual Special Issue (VSI) "New Trends on Green Energy and Environmental Technologies, with Special Focus on Biomass Valorization, Water and Waste Recycling", present summarized data corresponding to the accepted submissions, as well as additional comments regarding the thematic of the VSI. Overall, 83 manuscripts were received, with final publication of those having the highest quality, accepted after peer-reviewing. The Editors think that the result is a set of very interesting papers that increase the knowledge on the matter, and which would be useful for researchers and the whole society.

Sustainable asphalt mastics made up recycling waste as filler.

The continuous growth of waste is generating worldwide more and more increasing related environmental concerns. Anything that is not recycled or recuperated from waste represents a loss of raw materials and other production factors used in the manufacture, transport and consumer phases of the product. This research explored the potential of three waste namely Construction and Demolition (CD) waste, Fly Ash (FA), and Jet Grouting (JG) waste as fillers in comparison to the traditional limestone one for making hot asphalt mastics for road pavement, through a rheological analysis and environmental compatibility tests towards the release of potentially toxic elements. A total of eight asphalt mastics were prepared by using two filler-to-binder weight ratios (f/b) of 0.5 and 1 for blending each filler with a neat bitumen 50/70 penetration grade. The Frequency Sweep test and the Multiple Stress Creep and Recovery (MSCR) test were carried out to investigate the rheological properties of the asphalt mastics. Asphalt mastics containing FA and JG fillers were found to be more mechanically and environmentally efficient than traditional limestone mastic in particular by adopting an f/b equal to 1 where it was observed higher complex shear modulus values, G*, (on average 50% compared to the traditional asphalt mastic) and lower non-recoverable creep compliance values, Jnr, (on average 35% compared to the traditional asphalt mastic) at all test temperatures investigated. Based on the suggested ranking methodology, CD emerged as the filler performing in the same way of the traditional one. All the waste containing mastics, showed up noticeable environmental compatibility, being the potentially toxic elements completely immobilized into the mastics' structure e practically not releasable into acidic water, highlighting the waste recycling for road pavements as primary strategy to immobilize hazardous wastes.

Characterising contaminants distribution in marine-coastal sediments through multivariate and nonparametric statistical analyses: a complementary strategy supporting environmental monitoring and control.

This work investigates a statistical approach analysing data from monitoring activities on marine-coastal areas for environmental quality determination and surveillance. Analyses were performed on a database of the Environmental Protection and Prevention Agency of the Puglia Region. As, Cr, Ni, and Pb concentration values in marine sediments and biota from 2013 to 2015 and 2017 were processed to investigate different contaminant characteristics. Hierarchical cluster analysis identified three contaminant distribution classes with (1) highest Cr, Ni, and Pb concentrations, (2) highest As concentration, and (3) lowest contaminants concentration. The Kruskal-Wallis and Friedman tests showed that contaminant distributions were statistically different when considering the monitoring years and classes. However, statistical similarities resulted during the 2013-2017 and 2014-2015 periods. Spearman's coefficients displayed positive correlations among the pollutants in each matrix and mainly negative correlations for matrices comparison. This methodology aims to provide a practical support for monitoring to identify potential environmental deterioration over time and correlations with specific contamination sources.

Haloculture: A system to mitigate the negative impacts of pandemics on the environment, society and economy, emphasizing COVID-19.

COVID-19 (coronavirus disease) is a global pandemic that started in China in 2019 and has negatively affected all economic sectors of the world, including agriculture. However, according to estimates in different countries, agriculture has suffered less than other sectors such as construction, industry and tourism, so agricultural development can be a good option to compensate for the economic damage caused to other sectors. The quality of available water and soil resources for agricultural development is not only limited, but is also decreasing incrementally, so the use of saline and unconventional soil and water resources is inevitable. Biosaline agriculture or haloculture is a system in which highly saline water and soil resources are used sustainably for the economic production of agricultural crops. It seems that in the current situation of the world (with COVID-19's impact on agriculture on the one hand and the quantitative and qualitative decline of freshwater and soil on the other), haloculture with a re-reading of territorial capabilities has good potential to provide a part of human food supply. In this review article, the potential of haloculture to offset the adverse impacts of the pandemic is analyzed from five perspectives: increasing the area under cultivation, using unconventional water, stabilizing dust centers, increasing the body's immune resistance, and reducing losses in agribusiness due to the coronavirus. Overall, haloculture is an essential system, which COVID-19 has accelerated in the agricultural sector.

New research on water, waste and energy management, with special focus on antibiotics and priority pollutants.

The Editors of the Virtual Special Issue (VSI) "New Research on Water, Waste and Energy Management, with Special Focus on Antibiotics and Priority Pollutants" (VSI WWEM-20) here present details corresponding to papers that have been accepted, as well as further comments on the matter. It should be noted that the VSI should be associated to a Conference that had been initially programmed to be held in Rome during the summer of 2020, Unfortunately, it was postponed due to the COVID-19 pandemic. That conference was one of those within the series called "International Congress on Water, Waste and Energy Management". Although the Conference was postponed, the Call for Papers for the VSI was maintained by this journal. As a result, a set of very interesting papers were accepted after a careful peer-review process. We hope that it will be complemented with additional VSIs associated to future conferences corresponding to the series, increasing the knowledge on the topic.

New research on reduction and/or elimination of hazardous substances in the design, manufacture and application of chemical products.

The Virtual Special Issue (VSI) "New research on reduction and/or elimination of hazardous substances in the design, manufacture and application of chemical products" was initially associated to the "International Conference on Green Chemistry and Sustainable Engineering, GreenChem-20" that was postponed due to the COVID-19 pandemic. Anyway, the international conference will take place in the near future. However, the VSI was maintained in this journal, received a high number of submissions, and selected manuscripts have been accepted after peer-reviewing. The published papers constitute a set of high-quality contributions, which, in the future, could be complemented with others related to additional conferences about similar topics. In this editorial piece, the Editors include brief comments on papers accepted for publication in the Special Issue, as well as additional aspects of interest related to the subject.

SARS-CoV-2 and other viruses in soil: An environmental outlook.

In the present review, the authors shed light on the SARS-CoV-2 impact, persistence, and monitoring in the soil environment. With this purpose, several aspects have been deepened: i) viruses in soil ecosystems; ii) direct and indirect impact on the soil before and after the pandemic, and iii) methods for quantification of viruses and SARS-CoV-2 monitoring in soil. Viruses are present in soil (i.e. up to 417 × 107 viruses per g TS-1 in wetlands) and can affect the behavior and ecology of other life forms (e.g. bacteria), which are remarkably important for maintaining environmental equilibrium. Also, SARS-CoV-2 can be found in soil (i.e. up to 550 copies·g-1). Considering that the SARS-CoV-2 is very recent, poor knowledge is available in the literature on persistence in the soil and reference has been made to coronaviruses and other families of viruses. For instance, the survival of enveloped viruses (e.g. SARS-CoV) can reach 90 days in soils with 10% of moisture content at ambient. In such a context, the possible spread of the SARS-CoV-2 in the soil was evaluated by analyzing the possible contamination routes.

Supramolecular aggregation of colloidal natural organic matter masks priority pollutants released in water from peat soil.

Natural organic matter (NOM) from Sphagnum peat soil is extracted in water and subjected to several investigations to obtain structural and conformational information. Data show that the extracted NOM is self-organized in colloidal aggregates of variable sizes (from nano to micro scales, depending on the solvent composition, i.e., ultrapure water, solutions with denaturing agents, acetone, ethanol). Aggregates are formed by highly heterogeneous classes of organic compounds. According to the results of nuclear magnetic resonance and fluorescence measurements, the three-dimensional structure of aggregates, revealed by scanning electron microscope imaging, is supposed to be stabilized by the exposition of polar functional groups to the solvent, with consequent formation of hydrogen bonds, dipole-interactions and cation bridging. In contrast, the inner part of the aggregates displays hydrophobic features and is hypothesized to be further reinforced by the establishment of π-stacking interactions. The structure is assumed to be a supramolecular aggregation of small-medium oligomeric fragments (Max 750 Da) in which priority pollutants are entrapped by dispersive forces. The structures are shown to be nanosized spheroidal particles further aggregated to form higher dimension supra-structures. Carbohydrates play primary role, stabilizing the structure and giving marked hydrophilic properties to the aggregates.

Phytoremediation of pyrene-contaminated soils: A critical review of the key factors affecting the fate of pyrene.

Soil contamination by pyrene has increased over the years due to human-related activities, urgently demanding for remediation approaches to ensure human and environment safety. Within this frame, phytoremediation has been successfully applied over the years due to its green and cost-effectiveness features. The scope of this review includes the main phytoremediation mechanisms correlated with the removal of pyrene from contaminated soils and sediments to highlight the impact of different parameters and the supplement of additives on the efficiency of the treatment. Soil organic matter (SOM), plant species, aging time, environmental parameters (pH, soil oxygenation, and temperature) and bioavailability are among the main parameters affecting pyrene removal through phytoremediation. Phytoextraction only accounts for a small part of the entire phytoremediation process, but the addition of surfactants and chelating agents in planted soils could increase pyrene accumulation in plant tissues by 20% as a consequence of the increased pyrene bioavailability. Rhizodegradation is the main phytoremediation mechanism involved due to the activity of bacteria capable of degrading pyrene in the root area. Inoculated-planted soil treatments have the potential to decrease pyrene accumulation in shoots and roots by approximately 30 and 40%, respectively, further stimulating the proliferation of pyrene-degrading bacteria in the rhizosphere. Plant-fungi symbiotic association results in an enhanced accumulation of pyrene in shoots and roots of plants as well as a higher biodegradation. Finally, pyrene removal from soil can be improved in the presence of amendments, such as natural non-ionic surfactants, biochar, and bacterial mixtures.

Evaluation of the potential for caesium transfer from contaminated soil to the food chain as a consequence of uptake by edible vegetables.

This paper analyzes the effect of caesium (Cs) concentration on seed germination, seedling growth, root uptake, and leaf uptake of Lactuca sativa to understand the potential transfer of the metal from contaminated soil to humans through the food chain. The results of germination experiments show that seed germination and seedling growth strongly depend on increasing Cs concentration, with a decrease in the number of germinated seeds compared to the control up to 13.6% and a reduction in seedling growth up to 10.3% at the highest Cs tested concentration (15 mM). Uptake experiments indicate a low transfer of Cs from soil to leaves and roots of the plants, ranging between 0.06% and 2.2%. The transfer is found to be a not-monotone function of soil potassium (K) content, with highest values corresponding to 1-2 mM K2SO4. Increasing concentrations of K lead to lower translocation of Cs from roots to leaves. Values above the average amount applied (20 and 40 mM K2SO4) almost stop the translocation, suggesting the use of a high amount of K2SO4 protects the food chain from Cs contamination.