Nano copper in the diet of laying quails: productive performance, metabolism, and tissue concentration.

The study evaluated the use of nano copper in semi-purified diets for laying quails and its effect on performance, metabolic state, and bioavailability. A total of 160 (180-days-old) quails were distributed in a completely randomized design, in a 3x3+1 factorial. The copper sources used were copper sulfate, copper oxide, and nano copper oxide, at levels of 200, 400, and 800 ppm each, totaling nine treatments plus a negative control (with no copper inclusion). The following variables were determined: weight gain, feed intake, egg production, egg weight, hemoglobin, hematocrit, Cu in the tissues and Cu bioavailability. Data were subjected to analysis of variance at 5% probability. The effect of sources and levels, as well as the interaction between the factors were evaluated. When interaction was observed, the effect of sources was evaluated separately by the Tukey's test and the effect of levels by regression, both at 5% probability. Copper nano oxide can be used at up to 800 ppm in the diet of laying quails without altering the productive performance, and with higher bioavailability than conventional copper oxide. Hemoglobin increases with the inclusion of 200 and 400 ppm of nano copper oxide and the hematocrit with 400 ppm.

Influences of the Seasons of the Year and Physiographic Regions on the Levels of Calcium, Copper and Zinc in the Hoof Capsule of Foals Pre- and Postweaning Raised in Native Pasture.

This study evaluated the levels of calcium (Ca), copper (Cu) and zinc (Zn) in the hoof of Criollo foals, pre- and postweaning, correlating them with the concentrations of these inorganic chemical compounds in soil and pasture in the different seasons of the year. We used 41 preweaning foals and 28 postweaning foals. Seventeen forage samples were collected in four seasons, later 10 soil samples per property in five distinct physiographic regions (Santa Maria, Dilermando de Aguiar, Jaguarão, Arroio Grande and Pelotas). There was variability in Ca, Cu and Zn concentrations in the hoof foal between distinct physiographic regions (P < .05), and between seasons. There was no association of preweaning and postweaning Ca levels with forage in the different physiographic regions. The concentrations of Cu and Zn showed positive association (R = 0.69, 0.43; P < .05) with the native pastures in the different physiographic regions in preweaning. In postweaning, only Cu was positively associated (R = 0.74; P < .05). Different season and physiographic regions influence the levels of Ca, Cu and Zn in the hoof capsule and native pasture during the pre- and postweaning stages.

Synthesis of silver-containing calcium aluminate particles and their effects on a MTA-based endodontic sealer.

OBJECTIVE: To synthetize calcium aluminate (C3A) and silver-containing C3A particles (C3A+Ag) testing their effects on the properties of a MTA-based endodontic sealer in comparison to an epoxy resin- and a calcium silicate-based sealer. METHODS: Pure C3A and C3A+Ag particles were synthesized by a chemical method and characterized using XRD to identify crystalline phases. SEM/EDS analysis investigated morphology, particle size, and elemental composition of particles. Setting time, flow, radiopacity, water sorption and solubility of commercial and modified sealers were evaluated according to ISO 6876/2012. The pH and ions release were measured using a pHmeter and a microwave induced plasma optical emission spectrometer. The inhibition of biofilm growth was evaluated by confocal laser scanning microscopy (CLSM). Data were rank transformed and analyzed by ANOVA and Tukey test (P<0.05). RESULTS: The C3A particles showed an irregular grain agglomerated structure with voids and pores. In C3A+Ag particles, Ag modified the material morphology, confirming the deposition of Ag. The physicochemical properties of the modified MTA-based sealer were similar to the commercial material, except for the significant increase in Ca+2 release. However, there was no Ag release. Setting time, flow, radiopacity, water sorption and solubility were adequate for all materials. All the materials showed alkaline pH. Antibiofilm effect was improved in the presence of C3A particles, while the biofilm inhibition was lower in the presence of Ag. SIGNIFICANCE: The modified sealer presented improved antibiofilm properties and calcium release, without dramatic effects on the other characteristics. It is expected a positive effect in its antimicrobial behavior.

Determination of total mercury and methylmercury in biological samples by photochemical vapor generation.

Cold vapor atomic absorption spectrometry (CV-AAS) based on photochemical reduction by exposure to UV radiation is described for the determination of methylmercury and total mercury in biological samples. Two approaches were investigated: (a) tissues were digested in either formic acid or tetramethylammonium hydroxide (TMAH), and total mercury was determined following reduction of both species by exposure of the solution to UV irradiation; (b) tissues were solubilized in TMAH, diluted to a final concentration of 0.125% m/v TMAH by addition of 10% v/v acetic acid and CH(3)Hg(+) was selectively quantitated, or the initial digests were diluted to 0.125% m/v TMAH by addition of deionized water, adjusted to pH 0.3 by addition of HCl and CH(3)Hg(+) was selectively quantitated. For each case, the optimum conditions for photochemical vapor generation (photo-CVG) were investigated. The photochemical reduction efficiency was estimated to be approximately 95% by comparing the response with traditional SnCl(2) chemical reduction. The method was validated by analysis of several biological Certified Reference Materials, DORM-1, DORM-2, DOLT-2 and DOLT-3, using calibration against aqueous solutions of Hg(2+); results showed good agreement with the certified values for total and methylmercury in all cases. Limits of detection of 6 ng/g for total mercury using formic acid, 8 ng/g for total mercury and 10 ng/g for methylmercury using TMAH were obtained. The proposed methodology is sensitive, simple and inexpensive, and promotes "green" chemistry. The potential for application to other sample types and analytes is evident.

Ultrasound-assisted vapor generation of mercury.

Cold vapor generation arising from reduction of both Hg(2+) and CH(3)Hg(+) occurs using ultrasonic (US) fields of sufficient density to achieve both localized heating as well as radical-based attack in solutions of formic and acetic acids and tetramethylammonium hydroxide (TMAH). A batch sonoreactor utilizing an ultrasonic probe as an energy source and a flow through system based on a US bath were optimized for this purpose. Reduction of CH(3)Hg(+) to Hg(0) occurs only at relatively high US field density (>10 W cm(-3) of sample solution) and is thus not observed when a conventional US bath is used for cold vapor generation. Speciation of mercury is thus possible by altering the power density during the measurement process. Thermal reduction of Hg(2+) is efficient in formic acid and TMAH at 70 degrees C and occurs in the absence of the US field. Room temperature studies with the batch sonoreactor reveal a slow reduction process, producing temporally broad signals having an efficiency of approximately 68% of that arising from use of a conventional SnCl(2) reduction system. Molecular species of mercury are generated at high concentrations of formic and acetic acid. Factors affecting the generation of Hg(0) were optimized and the batch sonoreactor used for the determination of total mercury in SLRS-4 river water reference material.