Towards a Customizable, SLA 3D-Printed Biliary Stent: Optimizing a Commercially Available Resin and Predicting Stent Behavior with Accurate In Silico Testing.

Inflammation of the bile ducts and surrounding tissues can impede bile flow from the liver into the intestines. If this occurs, a plastic or self-expanding metal (SEM) stent is placed to restore bile drainage. United States (US) Food and Drug Administration (FDA)-approved plastic biliary stents are less expensive than SEMs but have limited patency and can occlude bile flow if placed spanning a duct juncture. Recently, we investigated the effects of variations to post-processing and autoclaving on a commercially available stereolithography (SLA) resin in an effort to produce a suitable material for use in a biliary stent, an FDA Class II medical device. We tested six variations from the manufacturer's recommended post-processing and found that tripling the isopropanol (IPA) wash time to 60 min and reducing the time and temperature of the UV cure to 10 min at 40 °C, followed by a 30 min gravity autoclave cycle, yielded a polymer that was flexible and non-cytotoxic. In turn, we designed and fabricated customizable, SLA 3D-printed polymeric biliary stents that permit bile flow at a duct juncture and can be deployed via catheter. Next, we generated an in silico stent 3-point bend test to predict displacements and peak stresses in the stent designs. We confirmed our simulation accuracy with experimental data from 3-point bend tests on SLA 3D-printed stents. Unfortunately, our 3-point bend test simulation indicates that, when bent to the degree needed for placement via catheter (~30°), the peak stress the stents are predicted to experience would exceed the yield stress of the polymer. Thus, the risk of permanent deformation or damage during placement via catheter to a stent printed and post-processed as we have described would be significant. Moving forward, we will test alternative resins and post-processing parameters that have increased elasticity but would still be compatible with use in a Class II medical device.

Multidrug resistance, biofilm formation and detection of bla CTX-M and bla VIM genes in E. coli and Salmonella isolates from chutney served at the street-food stalls of Bharatpur, Nepal.

Antimicrobial resistance (AMR) amid the bacteria found in ready-to-eat foods is a grave concern today warranting an immediate intervention. The current study was undertaken to explore the status of AMR in E. coli and Salmonella species in ready-to-eat Chutney samples (n = 150) served at the street food stalls in Bharatpur, Nepal, with a major focus on detecting extended-spectrum ß-lactamase (ESBL) and metallo ß-lactamase (MBL) genes along with biofilm formation. Average viable counts, coliform counts, and Salmonella Shigella counts were 1.33 × 106±141481.4, 1.83 × 105±91303.6, and 1.24 × 105±63933.19 respectively. Out of 150 samples, 41 (27.33%) harbored E. coli, of which 7 were E. coli O157:H7; whereas Salmonella spp. were found in 31 (20.67%) samples. Bacterial contamination of Chutney by E. coli and Salmonella and ESBL-production were both found significantly affected by different sources of water used, personal hygiene and literacy rate of the vendors as well as by the type of cleaning materials used to wash knives and chopping boards (P < 0.05). Antibiotic susceptibility testing revealed that imipenem was the most effective drug against both types of bacterial isolates. Additionally, 14 (45.16%) Salmonella isolates and 27 (65.85%) E. coli isolates were found to be multi-drug resistant (MDR). Total ESBL (bla CTX-M) producers reported were 4 (12.90%) Salmonella spp. and 9 (21.95%) E. coli. Only 1 (3.23%) Salmonella spp. and 2 (4.88%) E. coli isolates were bla VIM gene carriers. Dissemination of knowledge of personal hygiene amongst the street vendors and consumer awareness regarding ready-to-eat foods are crucial factors that can be suggested to curtail the emergence and transmission of food-borne pathogens.