In Vitro Study of Composite Cements on Mesenchymal Stem Cells of Palatal Origin.

Uniform filler distribution in composites is an important requirement. Therefore, BaO glass, nano hydroxyapatite and quartz filler distribution was realized through PCL microcapsules which progressively release filler during matrix polymerization. Two composites were realized based on a complex matrix containing BisGMA, UDMA, HEMA and PEG400 mixed with a previously described mineral filler: 33% for C1 and 31% for C2. The spreading efficiency was observed via SEM, revealing a complete disintegration of the microcapsules during C1 polymerization, while C2 preserved some microcapsule parts that were well embedded into the matrix beside BaO filler particles; this was confirmed by means of the EDS spectra. Mesenchymal stem cells of palatal origin were cultured on the composites for 1, 3, 5 and 7 days. The alkaline phosphatase (ALP) level was measured at each time interval and the cytotoxicity was tested after 3, 5 and 7 days of co-culture on the composite samples. The SEM investigation showed that both composites allowed for robust proliferation of the cells. The MSC cell pluripotency stage was observed from 1 to 3 days with an average level of ALP of 209.2 u/L for C1 and 193.0 u/L for C2 as well as a spindle cell morphology. Cell differentiation occurred after 5 and 7 days of culture, implied by morphological changes such as flattened, star and rounded shapes, observed via SEM, which were correlated with an increased ALP level (279.4 u/L for C1 and 284.3 u/L for C2). The EDX spectra after 7 days of co-culture revealed increasing amounts of P and Ca close to the hydroxyapatite stoichiometry, indicating the stimulation of the osteoinductive behavior of MSCs by C1 and C2. The MTT assay test showed a cell viability of 98.08% for C1 and 97.33% for C2 after 3 days, proving the increased biocompatibility of the composite samples. The cell viability slightly decreased at 5 and 7 days but the results were still excellent: 89.5% for C1 and 87.3% for C2. Thus, both C1 and C2 are suitable for further in vivo testing.

Sensitive detection of hydroquinone using exfoliated graphene-Au/glassy carbon modified electrode.

Graphene nanosheets (EGr) were electrochemically prepared through one-step exfoliation of a graphite rod in a mixture of H2SO4:HNO3 (3:1) at low bias (4 V). Subsequently, gold nanoparticles were attached to the graphene surface (EGr-Au) by the reduction of the metal precursor (HAuCl4) in aqueous solution containing dispersed graphene sheets. According to the XRD investigation, the synthesized material consists of a mixture of few-layer (86%) and multi-layer (14%) graphene. The interlayer distance was found to be in the range of 0.466-0.342 nm, which is larger than the interlayer distance in graphite (0.335 nm). The average size of gold nanoparticles in the EGr-Au sample was 24 nm, in excellent agreement with the TEM results. The synthesized material was then employed to modify a glassy carbon (GC) substrate, in order to obtain a modified electrode (GC/EGr-Au). Next, the electrochemical behavior of hydroquinone (HQ) in the presence and absence of interfering species, catechol (CAT) and bisphenol A (BPA) was studied and the corresponding calibration curves were plotted. Thus, in solutions without interfering species, the GC/EGr-Au electrode has a wide linear range (3 × 10-7-10-4 M), high sensitivity (0.089 A M-1) and low detection limit (LOD = 10-7 M; S/N = 3). The presence of either catechol or bisphenol A leads to the increase of LOD to 2 × 10-7 M, and in addition changes the electrode sensitivity, up to 0.146 A M-1.

Enhancing dentin bonding through new adhesives formulations with natural polyphenols, tricalcium phosphate and chitosan.

OBJECTIVES: The aim of the study was to develop new adhesive formulations that include natural polyphenols extracted from green tea (GTE), tricalcium phosphate (TCP) and chitosan to improve dentin bonding characteristics and cytotoxicity. METHODS: Four experimental adhesives were formulated under laboratory conditions. The groups differed in the integration of either GTE and/or TCP + chitosan. The four experimental and one clinically proven reference adhesive underwent shear bond testing after 24 h and 6 months of aging (n = 200) with subsequent fractographic analysis. Bond morphology was analyzed under a scanning electron microscope. The presence of phenolic compounds was validated by high performance liquid chromatography. Cytotoxicity was assessed by the WST-1 colorimetric assay on eluates up to 6 months. Statistical analysis was performed by one- and three-way ANOVA, Games-Howell and Tukey's post-hoc test as well as multiple students t-tests (α = 0.05). Weibull analysis was further conducted. RESULTS: The addition of GTE into the bonding agent did show immediate (p = 0.023, p = 0.013) and long-term (p < 0.001) effects on bond strength. After 24 h, GTE doped groups performed equal to the reference (p = 0.501, p = 0.270) and TCP and chitosan displayed improvements in reliability (m=4.0, m=4.3). Bond strength is retained after aging by adding GTE (p = 0.983). The additional presence of TCP and chitosan reduces it (p = 0.026). Excluding cohesive and mixed failures, the reference adhesive performed statistically equal to three of the four experimental groups. No long-term cytotoxic effects were shown. SIGNIFICANCE: The integration of GTE can enhance bond strength and a calcium source helps to improve immediate bond reliability.

The Precursors Used for Developing Geopolymer Composites for Circular Economy-A Review.

Considering recent climate changes, special importance is given to any attempt to depollute and protect the environment. A circular economy seems to be the ideal solution for the valorization of mineral waste, resulting from various industrial branches, by reintroducing them in the process of obtaining alternative building materials, more friendly to the environment. Geopolymers can be considered as a promising option compared to Portland cement. Information about the influence of the composition of the precursors, the influence of the activation system on the mechanical properties or the setting time could lead to the anticipation of new formulations of geopolymers or to the improvement of some of their properties. Reinforcement components, different polymers and expansion agents can positively or negatively influence the properties of geopolymers in the short or long term.

Mechanical Properties of MiniBars™ Basalt Fiber-Reinforced Geopolymer Composites.

Fly ash-based geopolymers represent a new material, which can be considered an alternative to ordinary Portland cement. MiniBars™ are basalt fiber composites, and they were used to reinforce the geopolymer matrix for the creation of unidirectional MiniBars™ reinforced geopolymer composites (MiniBars™ FRBCs). New materials were obtained by incorporating variable amount of MiniBars™ (0, 12.5, 25, 50, 75 vol.% MiniBars™) in the geopolymer matrix. Geopolymers were prepared by mixing fly ash powder with Na2SiO3 and NaOH as alkaline activators. MiniBars™ FRBCs were cured at 70 °C for 48 h and tested for different mechanical properties. Optical microscopy and SEM were employed to investigate the fillers and MiniBars™ FRBC. MiniBars™ FRBC showed increasing mechanical properties by an increased addition of MiniBars™. The mechanical properties of MiniBars™ FRBC increased more than the geopolymer wtihout MiniBars™: the flexural strength > 11.59-25.97 times, the flexural modulus > 3.33-5.92 times, the tensile strength > 3.50-8.03 times, the tensile modulus > 1.12-1.30 times, and the force load at upper yield tensile strength > 4.18-7.27 times. SEM and optical microscopy analyses were performed on the fractured surface and section of MiniBars™ FRBC and confirmed a good geopolymer network around MiniBars™. Based on our results, MiniBars™ FRBC could be a very promising green material for buildings.

Developing Bioactive Hydrogels with Peptides for Dental Application.

Dental caries is an avoidable and complex condition impacting billions of individuals worldwide, posing a specific concern among younger generations, despite the progress of oral hygiene products. This deterioration occurs due to the acid demineralization of tooth enamel, leading to the loss of minerals from the enamel subsurface. The remineralisation of early enamel carious lesions could prevent the cavitation of teeth. The enamel protein amelogenin constitutes 90% of the total enamel matrix protein and plays a key role in the bio mineralisation process. The aim of this study is to investigate the self-assembly microstructure and reticulation behaviour of a newly developed bioactive hydrogel with leucine-rich amelogenin peptide (LRAP) intended for enamel remineralisation. SEM, AFM, UV-VIS, and FTIR analyses emphasize the ability of peptides to promote cell adhesion and the treatment of early carious lesions. In conclusion, short-chain peptides can be used in hydrogels for individual or professional use.

Advanced Dentistry Biomaterials Containing Graphene Oxide.

The aim of this study was to obtain three experimental resin-based cements containing GO and HA-Ag for posterior restorations. The samples (S0, S1, and S2) shared the same polymer matrix (BisGMA, TEGDMA) and powder mixture (bioglass (La2O3 and Sr-Zr), quartz, GO, and HA-Ag), with different percentages of graphene oxide (0%, 0.1%, 0.2% GO) and silver-doped hydroxyapatite (10%, 9.9%, 9.8% HA-Ag). The physical-chemical properties (water absorption, degree of conversion), mechanical properties (DTS, CS, FS), structural properties (SEM, AFM), and antibacterial properties (Staphylococcus aureus, Enterococcus faecalis, Streptococcus mutans, Porphyromonas gingivalis, and Escherichia coli) were investigated. The results showed that the mechanical properties, except for the diametral tensile test, increased with the rise in the %GO. After 28 days, water absorption increased with the rise in the %GO. The surface structure of the samples did not show major changes after water absorption for 28 days. The antibacterial effects varied depending on the samples and bacterial strains tested. After increasing the %GO and decreasing the %HA-Ag, we observed a more pronounced antibacterial effect. The presence of GO, even in very small percentages, improved the properties of the tested experimental cements.

Comparative Evaluation of Dental Enamel Microhardness Following Various Methods of Interproximal Reduction: A Vickers Hardness Tester Investigation.

Interproximal enamel reduction, also known as stripping, is a common orthodontic procedure that reduces the mesiodistal diameter of teeth, allowing for a balance of available space in dental arches. The aim of this study was to assess the enamel surface microhardness resulting from the application of currently available methods for interproximal reduction. Forty-two extracted human permanent teeth were divided into six different groups, each subjected to a therapeutic stripping procedure using various methods (i.e., diamond burs, abrasive strips of 90 µm, 60 µm, 40 µm, and 15 µm, and abrasive discs). Stripping was performed by a single individual in accordance with the manufacturers' recommendations for the various systems used. One of the proximal faces of the tooth underwent IPR, while the other side remained untreated for control. The hardness of the enamel surface was measured using a Vickers hardness tester. The control group achieved the hardest enamel surface (354.4 ± 41.02 HV1), while the lowest was observed for enamel surfaces treated with 90 µm abrasive strips (213.7 ± 118.6). The only statistically significant difference was identified in comparisons between the values measured for the control group and those obtained after stripping with diamond burs (p = 0.0159). Enamel microhardness varied depending on the stripping instrument used, but no statistically significant differences were found (p > 0.05). Optimal microhardness values, close to those of healthy enamel, were achieved after mechanical treatment with 15 µm abrasive strips and abrasive discs. Dental stripping is a safe therapeutic procedure that has a relatively minor influence on the microhardness of surface enamel.

Formulation and Characterization of New Experimental Dental Composites with Zirconium Filling in Different Forms.

Short glass fibers are generally used in posterior dental restorations to enhance the mechanical properties and improve the material microstructure. Two resin-based composites (S0 and SF) were formulated and characterized to investigate the influence of zirconium in their characteristics and properties. The organic part of the investigated materials was the same (BisGMA, TEGDMA, and a photochemical polymerization system), and in the inorganic part, besides quart, glassA, and hydroxylapatite with Zn, sample S0 contained strontium glass with zirconium and sample SF contained fiber powder of chopped zirconium. The samples were characterized by the degree of conversion (DC), mechanical properties, water sorption (WS), scanning electron microscopy (SEM), atomic force microscopy (AFM) before and after the WS test, and antimicrobial properties. The results obtained were subjected to one-way ANOVA and Tukey's statistical tests. Both samples had a high DC. Regarding the mechanical properties, both samples were very similar, except DTS, which was higher for the composite without fibers. After 14 days, the WS value of the SF sample was lower than that of the S0 sample. Water caused significant changes in the topography of the SF sample, but thanks to its antimicrobial properties and the diffusion phenomenon, SF had a more pronounced antimicrobial effect. This study shows that the addition of appropriate amounts of Sr-Zr-glass powder gives the material in which it is added similar properties to material containing chopped zirconium glass fiber powder. According to the antimicrobial test results, resin composites containing experimental zirconia fillings can be considered in future in vitro clinical studies for posterior reconstructions with significantly improved mechanical properties.

Antimicrobial Poly (Lactic Acid)/Copper Nanocomposites for Food Packaging Materials.

Composites based on polylactic acid (PLA) and copper for food packaging applications were obtained. Copper clusters were synthesized in polyethylene glycols 400 and 600, respectively, using ascorbic acid as a reducing agent, by reactive milling. Copper clusters were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FT-IR), and Ultraviolet-Visible (UV-VIS) spectroscopy. Copper/PLA composites containing Proviplast as plasticizer were characterized by FT-IR spectroscopy, mechanical tests, Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), absorption of the saline solution, contact angle, and antibacterial properties. It was observed that the concentration of Copper/PEG influenced the investigated properties. The mechanical properties of the samples decreased with the increasing of Copper/PEG concentration. We recorded the phase transformation temperatures and identified the exothermic or endothermic processes. The lowest absorption values were recorded in the case of the sample containing 1% Cu. The contact angle decreases with the increase in the concentration of the PEG 600-Cu mixture in the recipes. The increase in the content of Cu clusters favors the decrease in the temperature, taking place 15% wt mass losses. The obtained composites showed antibacterial properties for all tested strains. These materials could be used as alternative materials for obtaining biodegradable food packaging.

Mechanical Properties and Liquid Absorption of Calcium Phosphate Composite Cements.

Calcium phosphate cements present increased biocompatibility due to their chemical composition being similar to that of the hydroxyapatite in the hard tissues of the living body. It has certain limitations due to its poor mechanical properties, such as low tensile strength and increased brittleness. Thus, the optimal way to improve properties is through the design of novel composite cements. The purpose was fulfilled using a 25% hydroxyethyl methacrylate (HEMA) mixed with 3% urethane dimethacrzlate (UDMA) base matrix with various ratios of polyethylene glycol (PEG 400) and polycaprolactone (PCL). Mineral filler is based on tricalcium phosphate (TCP) with different chitosan ratio used as bio-response enhancer additive. Four mixtures were prepared: S0-unfilled polymer matrix; S1 with 50% TCP filler; S2 with 50% chitosan + TCP filler; and S3 with 17.5% chitosan + TCP mixed with 17.5% nano hydroxyapatite (HA). The mechanical properties testing revealed that the best compressive strength was obtained by S2, followed by S3, and the worst value was obtained for the unfilled matrix. The same tendency was observed for tensile and flexural strength. These results show that the novel filler system increases the mechanical resistance of the TCP composite cements. Liquid exposure investigation reveals a relative constant solubility of the used filler systems during 21 days of exposure: the most soluble fillers being S3 and S2 revealing that the additivated TCP is more soluble than without additives ones. Thus, the filler embedding mode into the polymer matrix plays a key role in the liquid absorption. It was observed that additive filler enhances the hydrophobicity of UDMA monomer, with the matrix resulting in the lowest liquid absorption values, while the non-additivated samples are more absorbent due to the prevalence of hydrolytic aliphatic groups within PEG 400. The higher liquid absorption was obtained on the first day of immersion, and it progressively decreased with exposure time due to the relative swelling of the surface microstructural features. The obtained results are confirmed by the microstructural changes monitored by SEM microscopy. S3 and S2 present a very uniform and compact filler distribution, while S1 presents local clustering of the TCP powder at the contact with the polymer matrix. The liquid exposure revealed significant pore formation in S0 and S1 samples, while S3 and S2 proved to be more resistant against superficial erosion, proving the best resistance against liquid penetration.

Advanced Geopolymer-Based Composites for Antimicrobial Application.

In most studies about geopolymeric materials used in construction, the antibacterial properties of the building materials are treated as secondary features. Today, antimicrobial properties are a key feature in many building applications. The main objective of this article is to summarize the state-of-the-art in the area of design, development, and applications of nanoparticles as additives to geopolymer composites used in construction to improve their physical mechanical properties and induce a potential antibacterial effect, protecting them against alkali-resistant bacteria. On the basis of the literature and authors' experience, the most important methods of obtaining especially the porous geopolymers, of nanomaterials used as additives, with potential antibacterial effect but also the potential mechanism of action against bacterial development were presented. The main findings show that using graphene oxide (GO) in geopolymer composites, but also other nanoparticles such as silver (Ag), zinc oxide (ZnO), silica (SiO2), titanium dioxide (TiO2), copper (Cu) as additives, is an effective way to induce a potential antibacterial effect and to improve the physical and mechanical properties in building materials.

Chemical and Structural Assessment of New Dental Composites with Graphene Exposed to Staining Agents.

Among the newest trends in dental composites is the use of graphene oxide (GO) nanoparticles to assure better cohesion of the composite and superior properties. Our research used GO to enhance several hydroxyapatite (HA) nanofiller distribution and cohesion in three experimental composites CC, GS, GZ exposed to coffee and red wine staining environments. The presence of silane A-174 on the filler surface was evidenced by FT-IR spectroscopy. Experimental composites were characterized through color stability after 30 days of staining in red wine and coffee, sorption and solubility in distilled water and artificial saliva. Surface properties were measured by optical profilometry and scanning electron microscopy, respectively, and antibacterial properties wer e assessed against Staphylococcus aureus and Escherichia coli. A colour stability test revealed the best results for GS, followed by GZ, with less stability for CC. Topographical and morphological aspects revealed a synergism between GZ sample nanofiller components that conducted to the lower surface roughness, with less in the GS sample. However, surface roughness variation due to the stain was affected less than colour stability at the macroscopic level. Antibacterial testing revealed good effect against Staphylococcus aureus and a moderate effect against Escherichia coli.

Gradual Drug Release Membranes and Films Used for the Treatment of Periodontal Disease.

Periodontitis is an inflammatory disease that, if not treated, can cause a lot of harm to the oral cavity, to the patients' quality of life, and to the entire community. There is no predictable standardized treatment for periodontitis, but there have been many attempts, using antibiotics, tissue regeneration techniques, dental scaling, or root planning. Due to the limits of the above-mentioned treatment, the future seems to be local drug delivery systems, which could gradually release antibiotics and tissue regeneration inducers at the same time. Local gradual release of antibiotics proved to be more efficient than systemic administration. In this review, we have made a literature search to identify the articles related to this topic and to find out which carriers have been tested for drug release as an adjuvant in the treatment of periodontitis. Considering the inclusion and exclusion criteria, 12 articles were chosen to be part of this review. The selected articles indicated that the drug-releasing carriers in periodontitis treatment were membranes and films fabricated from different types of materials and through various methods. Some of the drugs released by the films and membranes in the selected articles include doxycycline, tetracycline, metronidazole, levofloxacin, and minocycline, all used with good outcome regarding their bactericide effect; BMP-2, Zinc-hydroxyapatite nanoparticles with regenerative effect. The conclusion derived from the selected studies was that gradual drug release in the periodontal pockets is a promising strategy as an adjuvant for the treatment of periodontal disease.

New Composite Hydrogel Based on Whey and Gelatin Crosslinked with Copper Sulphate.

By-products from the meat and dairy industries are important sources of high biological value proteins. This paper explores possibilities for improving the swelling and integrity of a cross-linked whey and gelatin hydrogel with different amounts of CuSO4 × 5H2O. Overall, swelling tests demonstrate that cross-linked samples show a better hydration capacity and stability in the hydration medium, but different copper concentrations lead to different swelling behavior. At concentrations smaller than 0.39%, the sample lasts for 75 h in a water environment before beginning to disintegrate. At a concentration of copper sulphate higher than 0.55%, the stability of the sample increased substantially. The swelling kinetics has been investigated. The diffusion constant values increased with the increase in copper concentration, but, at the highest concentration of copper (0.86%), its value has decreased. Spectroscopy analyses such as Fourier transform infrared (FT-IR), X-ray diffraction (XRD), ultraviolet-visible spectroscopy (UV-VIS), and nuclear magnetic resonance (NMR) relaxometry analyses revealed changes in the secondary and tertiary structure of proteins as a result of the interaction of Cu2+ ions with functional groups of protein chains. In addition to its cross-linking ability, CuSO4 × 5H2O has also shown excellent antibacterial properties over common bacterial strains responsible for food spoilage. The result of this research demonstrates the potential of this hydrogel system as a unique material for food packaging.

Human Enamel Fluorination Enhancement by Photodynamic Laser Treatment.

Poor oral hygiene leads to serious damages of theteeth's surface enamel such as micro-abrasions and acid erosion. These alterations combined with bacterial plaque result in cavity appearance. Prophylactic measures include various techniques for enamel surface restoration. Fluorination is one of the most important treatments for this purpose. Therefore, in the present research, we investigated the classical fluorination treatment compared with laser photodynamic fluorination performed on human enamel samples with poor surface quality. Three sample groups were investigated: veneer (F), inlay (I), and crowns (C). The general morphologic aspect was investigated by scanning electron microscopy (SEM), and the specific details such as the fine microstructure and nanostructure were investigated by atomic force microscopy (AFM) of the surface roughness. The samples were also investigated by Fourier transformed infrared attenuated total reflectance (FTIR-ATR) to evidence the fluorination effect on the enamel surface. Results showed that all initial samples had an altered state with micro-abrasions and erosion with mineral loss, which increase the surface roughness. The F group was the most damaged, having a higher roughness, and the I group was less damaged. Classic fluorination treatment partially restored the enamel by local re-mineralization, but did not obtain the parameters of healthy enamel. However, a significant decrease of the roughness was observed (statistical relevance p = 0.001 with the Breusch-Pagan Test). This fact was supported by the presence of newly formed fluorides in the FTIR-ATR spectra. The photodynamic laser fluorination restores the enamel in an enhanced manner by a strong re-mineralization, which implies a significant roughness value decrease comparable to healthy enamel. The Breusch-Pagan Test confirmed the relevance with p = 0.001. This is due to an extended re-mineralization abundant in fluoride crystals as observed by AFM and FTIR. Statistical p-values regarding laser application were in the range of 0.02-0.06, supporting its relevance in the fluorination effect. The final conclusion is that the photodynamic effect is able to favor the newly formed fluoride deposition onto the affected sites of the enamel surface.

Photodynamic Therapy with Natural Photosensitizers in the Management of Periodontal Disease Induced in Rats.

This study aims to investigate the effect of new natural photosensitizers (PS) (based on oregano essential oil, curcuma extract, and arnica oil) through in vitro cytotoxicity and biological tests in rat-induced periodontal disease, treated with photodynamic therapy (aPDT). The cytotoxicity of PS was performed on human dental pulp mesenchymal stem cells (dMSCs) and human keratinocyte (HaCaT) cell lines. Periodontal disease was induced by ligation of the first mandibular molar of 25 rats, which were divided into 5 groups: control group, periodontitis group, Curcuma and aPDT-treated group, oregano and aPDT-treated group, and aPDT group. The animals were euthanized after 4 weeks of study. Computed tomography imaging has been used to evaluate alveolar bone loss. Hematological and histological evaluation showed a greater magnitude of the inflammatory response and severe destruction of the periodontal ligaments in the untreated group.. For the group with the induced periodontitis and treated with natural photosensitizers, the aPDT improved the results; this therapy could be an important adjuvant treatment. The obtained results of these preliminary studies encourage us to continue the research of periodontitis treated with natural photosensitizers activated by photodynamic therapy.

Synthesis and characterization of graphene oxide-zirconia (GO-ZrO2) and hydroxyapatite-zirconia (HA-ZrO2) nano-fillers for resin-based composites for load-bearing applications.

OBJECTIVES: The study aims to synthesize two different types of nano-fillers based on zirconia (ZrO2), which was functionalized with graphene oxide (GO-ZrO2), and hydroxyapatite (HA-ZrO2), and to implement them in an experimental methacrylate matrix containing new dimethacrylic oligomers. METHODS: Nano-particles were synthesized via a modified Hummer's method and a sol-gel route. Bisphenol A-glycidyl methacrylate oligomers (Bis-GMA336[0-1]) were synthesized from an epoxy resin that reacted with methacrylic acid in the presence of a basic catalyst. Traditional dental glass-fillers (Barium oxide/BaO and Barium fluoride/BaF2) were synthesized to create an experimental resin-based composite (RBC) used as reference. Filler morphology was evaluated via Transmission Electron Microscopy. RBCs were characterised by real-time Fourier transform infrared spectroscopy (degree of cure/DC, polymerisation kinetics), real-time spectrometry (light transmittance), 3-point bending test (flexural strength and modulus, Weibull parameters), and depth-sensing indentation test (plastic and elastic deformation parameters). RESULTS: The synthesized nanohybrid fillers proved good dispersing performance. Mechanical properties and materials' reliability are within or above the mean values reported in the literature for RBCs. Addition of HA-ZrO2-fillers resulted in a decrease light transmission, DC and mechanical properties. Except for the HA-ZrO2 RBC, materials showed a high resistance to softening in solvent. CONCLUSIONS: The synthesis of GO-ZrO2 and HA-ZrO2 nanohybrid particles and their implementation in experimental RBCs has proven successful. Adjustments of the light transmission through suitable co-fillers in addition to GO-ZrO2 as well as adjustments of the amount of HA-ZrO2 are necessary to enable reduced curing time (<20 s). CLINICAL SIGNIFICANCE: The addition of nanofillers with tailor-made properties can help improving the performance of modern restoratives.

Dental Sealant Composition-Retention Assessment in Young Permanent Molars.

Tooth decay in children and adolescents remains a public health problem, despite prophylaxis and preventive measures being largely available. The aim of our study was to evaluate the clinical behavior of four dental sealants, related to first permanent molar topography and patient age (when sealant was applied for the first time). We assessed, by means of visual inspection and palpation with a dental probe, a group of 200 children, enrolled corresponding to school age-grade (mean age of 7 years at baseline) and randomly divided according to the material used as dental sealant (Admira seal©, Embrace Wet Bond©, Fotoseal©, GC Fuji Triaje©) in 4 groups (n = 50). Sealant clinical evaluation was made at 6-, 12-, 18-month intervals for dental material retention assessment. At 6 months, the sealant detached the most from 3.6 molars, and the material used was Fotoseal© (27.6%). At 12 months, Fotoseal© (48.3%) and GC Fuji Triaje© (41.4%) from 3.6 molars express detachment. At 18 months, 4.6. molars sealed with Admira Seal© (25.7%) and Embrace Wet Bond© (28.6%) lost the sealant. We noticed less detachment in maxillary molars and if sealant was applied around 7 years of age. In conclusion, sealant application on first permanent molars must be encouraged and practitioners can choose between various materials available.

Surface Characteristics, Fluoride Release and Bond Strength Evaluation of Four Orthodontic Adhesives.

Orthodontic adhesives have similar properties in terms of fluoride release, roughness, shear bond strength or cement debris for specific clinical conditions. Three commercial consecrated orthodontic adhesives (Opal Seal®, Blugloo®, Light Bond®) were compared with an experimental orthodontic material (C1). Brackets were bonded to enamel using a self-etch technique followed by adhesive application and then de-bonded 60 days later. Share bond strength evaluation, scanning electron microscopy, atomic force microscopy and fluoride release analysis were performed. The highest amount of daily and cumulative fluoride release was obtained for the experimental material, while the lowest value was observed for Opal Seal®. The materials evaluated in the current study presented adequate shear bond strength, with the experimental material having a mean value higher than Opal Seal and Blugloo. The atomic force microscopy measurements indicated that the smoothest initial sample is Opal Seal® followed by Light Bond®. Scanning electron microscopy evaluation indicated different aspects of cement debris on the enamel and/or bracket surface, according to the type of adhesive. The experimental material C1 presented adequate properties in terms of shear bond strength, fluoride release, roughness and enamel characteristics after de-bonding, compared to the commercial materials. Under these circumstances, it can be considered for clinical testing.