Melatonin and serotonin: Mediators in the symphony of plant morphogenesis.

Melatonin and serotonin are important signaling and stress mitigating molecules that play important roles across growth and development in plants. Despite many well-documented responses, a systematic investigation of the entire metabolic pathway (tryptophan, tryptamine, and N-acetylserotonin) does not exist, leaving many open questions. The objective of this study was to determine the responses of Hypericum perforatum (L.) to melatonin, serotonin, and their metabolic precursors. Two well-characterized germplasm lines (#4 and 112) created by mutation and a haploid breeding program were compared to wild type to identify specific responses. Germplasm line 4 has lower regenerative and photosynthetic capacity than either wild type or line 112, and there are documented significant differences in the chemistry and physiology of lines 4 and 112. Supplementation of the culture media with tryptophan, tryptamine, N-acetylserotonin, serotonin, or melatonin partially reversed the regenerative recalcitrance and growth impairment of the germplasm lines. Quantification of phytohormones revealed crosstalk between the indoleamines and related phytohormones including cytokinin, salicylic acid, and abscisic acid. We hypothesize that melatonin and serotonin function in coordination with their metabolites in a cascade of phytochemical responses including multiple pathways and phytohormone networks to direct morphogenesis and protect photosynthesis in H. perforatum.

Variation and correlation of properties in different grades of maple syrup.

Thirty five commercial maple syrups from twelve producers in Southern Ontario were evaluated for properties including light transmittance, autofluorescence, density, pH, total soluble solids (TSS), glucose and fructose content, total phenol content, antioxidant potential and mineral content (Mg, Mn, P, Zn, Ca, K, Fe and Pb). A high degree of variability was found in many characteristics, often exceeding an order of magnitude. Syrups were categorized based on light transmission at 560 nm into amber (12), dark (13) and very dark (10) using International Maple Syrup Institute (IMSI) guidelines. No statistical differences were found among grades of syrup for density, pH, TSS, glucose, fructose, total reducing sugars, glucose:fructose ratio, magnesium, manganese or potassium. Darker syrups showed significantly higher autofluorescence, total phenol content, antioxidant potential, phosphorous, calcium and total mineral content. Significant negative correlations of percent transmission with total phenol content, antioxidant potential and total mineral content are reported. Significant positive correlations among total phenol content, antioxidant potential and total mineral content are also described. The results from this study suggest that darker syrups tend to contain more beneficial traits and may be applied in developing functional foods and value added products.

Assessment of genetic fidelity of micropropagated date palm (Phoenix dactylifera L.) plants by RAPD and ISSR markers assay.

RAPD (Random Amplified Polymorphic DNA) and ISSR (Inter-Simple Sequence Repeats) markers assay were employed to validate the genetic stability of date palm (Phoenix dactylifera L.) plants multiplied through somatic embryogenesis with upto forty two in vitro subcultures. Out of the 160 RAPD and 21 ISSR primers screened, 30 RAPD and 12 ISSR primers produced a total of 347 (246 RAPDs + 101 ISSRs) clear, distinct and reproducible amplicons, which were monomorphic across all micropropagated plants (27) studied. Thus, a total 8592 bands (number of plants analysed x number of amplicons with all the primers) were generated which exhibited homogeneous banding patterns with both RAPD and ISSR markers. These results indicate that the micropropagation protocol developed by us for rapid in vitro multiplication is appropriate and suitable for clonal propagation of date palm and corroborated the fact that somatic embryogenesis can also be used as one of the safest modes for production of true-to-type plants.

Application of 3D printing to prototype and develop novel plant tissue culture systems.

BACKGROUND: Due to the complex process of designing and manufacturing new plant tissue culture vessels through conventional means there have been limited efforts to innovate improved designs. Further, development and availability of low cost, energy efficient LEDs of various spectra has made it a promising light source for plant growth in controlled environments. However, direct replacement of conventional lighting sources with LEDs does not address problems with uniformity, spectral control, or the challenges in conducting statistically valid experiments to assess the effects of light. Prototyping using 3D printing and LED based light sources could help overcome these limitations and lead to improved culture systems. RESULTS: A modular culture vessel design in which the fluence rate and spectrum of light are independently controlled was designed, prototyped using 3D printing, and evaluated for plant growth. This design is compatible with semi-solid and liquid based culture systems. Observations on morphology, chlorophyll content, and chlorophyll fluorescence based stress parameters from in vitro plants cultured under different light spectra with similar overall fluence rate indicated different responses in Nicotiana tabacum and Artemisia annua plantlets. This experiment validates the utility of 3D printing to design and test functional vessels and demonstrated that optimal light spectra for in vitro plant growth is species-specific. CONCLUSIONS: 3D printing was successfully used to prototype novel culture vessels with independently controlled variable fluence rate/spectra LED lighting. This system addresses several limitations associated with current lighting systems, providing more uniform lighting and allowing proper replication/randomization for experimental plant biology while increasing energy efficiency. A complete procedure including the design and prototyping of a culture vessel using 3D printing, commercial scale injection molding of the prototype, and conducting a properly replicated experiment are discussed. This open source design has the scope for further improvement and adaptation and demonstrates the power of 3D printing to improve the design of culture systems.

Micropropagation and Biomass Production of True-to-Type Stevia rebaudiana Bertoni.

Here we describe an efficient micropropagation protocol for Stevia rebaudiana Bertoni. We present experiments carried out to optimize the suitable media for in vitro shoot multiplication and root induction and to study the effect of culture vessel on shoot multiplication. Among all different media tested for in vitro shoot multiplication, hormone-free liquid medium is most suitable. The highest number of nodes per shoot (5.4) and length of shoot (4.76 cm) at 4 weeks after subculturing are observed when single node explants are placed on modified MS medium supplemented with 1 % sucrose and 0.7 % agar. The highest response of multiplication rate (9.56) is observed on half strength of macroelement of MS with full strength of microelement of MS and 170 mg/l KH2PO4, and 185 mg/l MgSO4 in plastic growth container. Further, RAPD marker analysis of in vitro-raised plants maintained their clonal fidelity and true-to-type without showing any somaclonal variation.