Electrochemical versus Photoelectrochemical Water Oxidation Kinetics on Bismuth Vanadate (Photo)anodes.

This study reports a comparison of the kinetics of electrochemical (EC) versus photoelectrochemical (PEC) water oxidation on bismuth vanadate (BiVO4) photoanodes. Plots of current density versus surface hole density, determined from operando optical absorption analyses under EC and PEC conditions, are found to be indistinguishable. We thus conclude that EC water oxidation is driven by the Zener effect tunneling electrons from the valence to conduction band under strong bias, with the kinetics of both EC and PEC water oxidation being determined by the density of accumulated surface valence band holes. We further demonstrate that our combined optical absorption/current density analyses enable an operando quantification of the BiVO4 photovoltage as a function of light intensity.

The effect of illumination on the formation of metal halide perovskite films.

Optimizing the morphology of metal halide perovskite films is an important way to improve the performance of solar cells when these materials are used as light harvesters, because film homogeneity is correlated with photovoltaic performance. Many device architectures and processing techniques have been explored with the aim of achieving high-performance devices, including single-step deposition, sequential deposition and anti-solvent methods. Earlier studies have looked at the influence of reaction conditions on film quality, such as the concentration of the reactants and the reaction temperature. However, the precise mechanism of the reaction and the main factors that govern it are poorly understood. The consequent lack of control is the main reason for the large variability observed in perovskite morphology and the related solar-cell performance. Here we show that light has a strong influence on the rate of perovskite formation and on film morphology in both of the main deposition methods currently used: sequential deposition and the anti-solvent method. We study the reaction of a metal halide (lead iodide) with an organic compound (methylammonium iodide) using confocal laser scanning fluorescence microscopy and scanning electron microscopy. The lead iodide crystallizes before the intercalation of methylammonium iodide commences, producing the methylammonium lead iodide perovskite. We find that the formation of perovskite via such a sequential deposition is much accelerated by light. The influence of light on morphology is reflected in a doubling of solar-cell efficiency. Conversely, using the anti-solvent method to form methyl ammonium lead iodide perovskite in a single step from the same starting materials, we find that the best photovoltaic performance is obtained when films are produced in the dark. The discovery of light-activated crystallization not only identifies a previously unknown source of variability in opto-electronic properties, but also opens up new ways of tuning morphology and structuring perovskites for various applications.

Linking in situ charge accumulation to electronic structure in doped SrTiO3 reveals design principles for hydrogen-evolving photocatalysts.

Recently, high solar-to-hydrogen efficiencies were demonstrated using La and Rh co-doped SrTiO3 (La,Rh:SrTiO3) incorporated into a low-cost and scalable Z-scheme device, known as a photocatalyst sheet. However, the unique properties that enable La,Rh:SrTiO3 to support this impressive performance are not fully understood. Combining in situ spectroelectrochemical measurements with density functional theory and photoelectron spectroscopy produces a depletion model of Rh:SrTiO3 and La,Rh:SrTiO3 photocatalyst sheets. This reveals remarkable properties, such as deep flatband potentials (+2 V versus the reversible hydrogen electrode) and a Rh oxidation state dependent reorganization of the electronic structure, involving the loss of a vacant Rh 4d mid-gap state. This reorganization enables Rh:SrTiO3 to be reduced by co-doping without compromising the p-type character. In situ time-resolved spectroscopies show that the electronic structure reorganization induced by Rh reduction controls the electron lifetime in photocatalyst sheets. In Rh:SrTiO3, enhanced lifetimes can only be obtained at negative applied potentials, where the complete Z-scheme operates inefficiently. La co-doping fixes Rh in the 3+ state, which results in long-lived photogenerated electrons even at very positive potentials (+1 V versus the reversible hydrogen electrode), in which both components of the complete device operate effectively. This understanding of the role of co-dopants provides a new insight into the design principles for water-splitting devices based on bandgap-engineered metal oxides.

Electron Accumulation Induces Efficiency Bottleneck for Hydrogen Production in Carbon Nitride Photocatalysts.

This study addresses the light intensity dependence of charge accumulation in a photocatalyst suspension, and its impact on both charge recombination kinetics and steady-state H2 evolution efficiency. Cyanamide surface functionalized melon-type carbon nitride (NCNCNx) has been selected as an example of emerging carbon nitrides photocatalysts because of its excellent charge storage ability. Transient spectroscopic studies (from ps to s) show that the bimolecular recombination of photogenerated electrons and holes in NCNCNx can be well described by a random walk model. Remarkably, the addition of hole scavengers such as 4-methylbenzyl alcohol can lead to ∼400-fold faster recombination kinetics (lifetime shortening to ∼10 ps). We show that this acceleration is not the direct result of ultrafast hole extraction by the scavenger, but is rather caused by long-lived electron accumulation in NCNCNx after hole extraction. The dispersive pseudo-first order recombination kinetics become controlled by the density of accumulated electrons. H2 production and steady-state spectroscopic measurements indicate that the accelerated recombination caused by electron accumulation limits the H2 generation efficiency. The addition of a reversible electron acceptor and mediator, methyl viologen (MV2+), accelerates the extraction of electrons from the NCNCNx and increases the H2 production efficiency under one sun irradiation by more than 30%. These results demonstrate quantitatively that while long-lived electrons are essential to drive photoinduced H2 generation in many photocatalysts, excessive electron accumulation may result in accelerated recombination losses and lower performance, and thus highlight the importance of efficient electron and hole extraction in enabling efficient water splitting photocatalysts.

Cu2O Nanowire Photocathodes for Efficient and Durable Solar Water Splitting.

Due to its abundance, scalability, and nontoxicity, Cu2O has attracted extensive attention toward solar energy conversion, and it is the best performing metal oxide material. Until now, the high efficiency devices are all planar in structure, and their photocurrent densities still fall well below the theoretical value of 14.5 mA cm(-2) due to the incompatible light absorption and charge carrier diffusion lengths. Nanowire structures have been considered as a rational and promising approach to solve this issue, but due to various challenges, performance improvements through the use of nanowires have rarely been achieved. In this work, we develop a new synthetic method to grow Cu2O nanowire arrays on conductive fluorine-doped tin oxide substrates with well-controlled phase and excellent electronic and photonic properties. Also, we introduce an innovative blocking layer strategy to enable high performance. Further, through material engineering by combining a conformal nanoscale p-n junction, durable protective overlayer, and uniform catalyst decoration, we have successfully fabricated Cu2O nanowire array photocathodes for hydrogen generation from solar water splitting delivering unprecedentedly high photocurrent densities of 10 mA cm(-2) and stable operation beyond 50 h, establishing a new benchmark for metal oxide based photoelectrodes.

Solution transformation of Cu2O into CuInS2 for solar water splitting.

Though Cu2O has demonstrated high performance as a photocathode for solar water splitting, its band gap is too large for efficient use as the bottom cell in tandem configurations. Accordingly, copper chalcopyrites have recently attracted much attention for solar water splitting due to their smaller and tunable band gaps. However, their fabrication is mainly based on vacuum evaporation, which is an expensive and energy consuming process. Here, we have developed a novel and low-cost solution fabrication method, and CuInS2 was chosen as a model material due to its smaller band gap compared to Cu2O and relatively simple composition. The nanostructured CuInS2 electrodes were synthesized at low temperature in crystalline form by solvothermal treatment of electrochemically deposited Cu2O films. Following the coating of overlayers and decoration with Pt catalyst, the as-fabricated CuInS2 electrode demonstrated water splitting photocurrents of 3.5 mA cm(-2) under simulated solar illumination. To the best of our knowledge, this is the highest performance yet reported for a solution-processed copper chalcopyrite electrode for solar water splitting. Furthermore, the electrode showed good stability and had a broad incident photon-to-current efficiency (IPCE) response to wavelengths beyond 800 nm, consistent with the smaller bandgap of this material.

Solution-processable polymers of intrinsic microporosity for gas-phase carbon dioxide photoreduction.

Four solution-processable, linear conjugated polymers of intrinsic porosity are synthesised and tested for gas phase carbon dioxide photoreduction. The polymers' photoreduction efficiency is investigated as a function of their porosity, optical properties, energy levels and photoluminescence. All polymers successfully form carbon monoxide as the main product, without the addition of metal co-catalysts. The best performing single component polymer yields a rate of 66 µmol h-1 m-2, which we attribute to the polymer exhibiting macroporosity and the longest exciton lifetimes. The addition of copper iodide, as a source of a copper co-catalyst in the polymers shows an increase in rate, with the best performing polymer achieving a rate of 175 µmol h-1 m-2. The polymers are active for over 100 h under operating conditions. This work shows the potential of processable polymers of intrinsic porosity for use in the gas phase photoreduction of carbon dioxide towards solar fuels.

Impact of the Synthesis Route on the Water Oxidation Kinetics of Hematite Photoanodes.

Operando spectroelectrochemical analysis is used to determine the water oxidation reaction kinetics for hematite photoanodes prepared using four different synthetic procedures. While these photoanodes exhibit very different current/voltage performance, their underlying water oxidation kinetics are found to be almost invariant. Higher temperature thermal annealing was found to correlate with a shift in the photocurrent onset potential toward less positive potentials, assigned to a suppression of both back electron-hole recombination and of charge accumulation in intra-bandgap states, indicating these intra-bandgap states do not contribute directly to water oxidation.

In situ observation of picosecond polaron self-localisation in α-Fe2O3 photoelectrochemical cells.

Hematite (α-Fe2O3) is the most studied artificial oxygen-evolving photo-anode and yet its efficiency limitations and their origin remain unknown. A sub-picosecond reorganisation of the hematite structure has been proposed as the mechanism which dictates carrier lifetimes, energetics and the ultimate conversion yields. However, the importance of this reorganisation for actual device performance is unclear. Here we report an in situ observation of charge carrier self-localisation in a hematite device, and demonstrate that this process affects recombination losses in photoelectrochemical cells. We apply an ultrafast, device-based optical-control method to resolve the subpicosecond formation of small polarons and estimate their reorganisation energy to be ~0.5 eV. Coherent oscillations in the photocurrent signals indicate that polaron formation may be coupled to specific phonon modes (<100 cm-1). Our results bring together spectroscopic and device characterisation approaches to reveal new photophysics of broadly-studied hematite devices.

Rational design of a neutral pH functional and stable organic photocathode.

In this work we lay out design guidelines for catalytically more efficient organic photocathodes achieving stable hydrogen production in neutral pH. We propose an organic photocathode architecture employing a NiO hole selective layer, a PCDTBT:PCBM bulk heterojunction, a compact TiO2 electron selective contact and a RuO2 nanoparticle catalyst. The role of each layer is discussed in terms of durability and function. With this strategically designed organic photocathode we obtain stable photocurrent densities for over 5 h and discuss routes for further performance improvement.

Low-Temperature Atomic Layer Deposition of Crystalline and Photoactive Ultrathin Hematite Films for Solar Water Splitting.

We developed a low-temperature atomic layer deposition route to deposit phase pure and crystalline hematite (α-Fe2O3) films at 230 °C without the need for postannealing. Homogenous and conformal deposition with good aspect ratio coverage was demonstrated on a nanostructured substrate and analyzed by transmission electron microscopy. These as-deposited α-Fe2O3 films were investigated as photoanodes for photoelectrochemical water oxidation and found to be highly photoactive. Combined with a TiO2 underlayer and a low-cost Ni(OH)2 catalyst, hematite films of less than 10 nm in thickness reached photocurrent densities of 0.3 mA cm(-2) at 1.23 V vs RHE and a photocurrent onset potential of less than 0.9 V vs RHE, previously unseen for films this thin and without high temperature annealing. In a thickness-dependent photoelectrochemical analysis, we identified a hematite thickness of only 10 nm to yield the highest internal quantum efficiency when using a suitable underlayer such as TiO2 that induces doping of the hematite film and reduces electron/hole recombination at the back contact. We find that, at high bias potentials, photocurrent density and quantum efficiency proportionally increase with light absorption in films thinner than 10 nm and are limited by the space charge layer width in thicker films. Thus, we propose to apply hematite films of 10 nm in thickness for future developments on suitable nanostructured conductive scaffolds that can now be extended to organic scaffolds due to our low-temperature process.

Efficient photosynthesis of carbon monoxide from CO2 using perovskite photovoltaics.

Artificial photosynthesis, mimicking nature in its efforts to store solar energy, has received considerable attention from the research community. Most of these attempts target the production of H2 as a fuel and our group recently demonstrated solar-to-hydrogen conversion at 12.3% efficiency. Here, in an effort to take this approach closer to real photosynthesis, which is based on the conversion of CO2, we demonstrate the efficient reduction of CO2 to carbon monoxide driven solely by simulated sunlight using water as the electron source. Employing series-connected perovskite photovoltaics and high-performance catalyst electrodes, we reach a solar-to-CO efficiency exceeding 6.5%, which represents a new benchmark in sunlight-driven CO2 conversion. Considering hydrogen as a secondary product, an efficiency exceeding 7% is observed. Furthermore, this study represents one of the first demonstrations of extended, stable operation of perovskite photovoltaics, whose large open-circuit voltage is shown to be particularly suited for this process.