Determination of Electrical and Mechanical Properties of Liquids Using a Resonator with a Longitudinal Electric Field.

The possibility of determining the elastic modules, viscosity coefficients, dielectric constant and electrical conductivity of a viscous conducting liquid using a piezoelectric resonator with a longitudinal electric field is shown. For the research, we chose a piezoelectric resonator made on an AT-cut quartz plate with round electrodes, operating with a shear acoustic mode at a frequency of about 4.4 MHz. The resonator was fixed to the bottom of a 30 mL liquid container. The samples of a mixture of glycerol and water with different viscosity and conductivity were used as test liquids. First, the frequency dependences of the real and imaginary parts of the electrical impedance of a free resonator were measured and, using the Mason electromechanical circuit, the elastic module, viscosity coefficient, piezoelectric constant and dielectric constant of the resonator material (quartz) were determined. Then, the container was filled with the test sample of a liquid mixture so that the resonator was completely covered with liquid, and the measurement of the frequency dependences of the real and imaginary parts of the electrical impedance of the loaded resonator was repeated. The dependences of the frequency of parallel and series resonances, as well as the maximum values of the electrical impedance and admittance on the conductivity of liquids for various viscosity values, were plotted. It was shown that these dependences can be used to unambiguously determine the viscosity and conductivity of the test liquid. Next, by fitting the theoretical frequency dependences of the real and imaginary parts of the electrical impedance of the resonator loaded with the liquid under study to the experimental dependences, the elastic module of the liquid and its dielectric constant were determined.

The Study of the Acoustic Characteristics of Chitosan Acetate Film Using a Radial Electric Field Excited Resonator.

Currently, the lateral electric field excited resonators are used for the creation of various sensors. We have recently proposed a new type of acoustic resonator called radial electric field excited disk acoustic resonator. The advantage of this type of resonator is its high sensitivity to mechanical and electrical boundary conditions on its free surface. This makes it possible to determine both the acoustic and electrical properties of a thin layer of material deposited on the free end of the resonator. In this work, we used a radial electric field excited disk acoustic resonator of Russian-made barium plumbum zirconate titanate (BPZT) piezoceramics. With the help of this resonator, the material constants for the piezoceramic sample were refined, and their temperature dependencies were determined. Then, this resonator was used to determine the elastic modulus, viscosity, and conductivity of the chitosan acetate film in air and ammonia vapors of various concentrations. It was shown that the chitosan acetate film under the influence of ammonia vapor significantly changes its mechanical properties and increases its electrical conductivity thousands of times, and then completely restores its properties.

The Effect of Glycerol-Based Suspensions on the Characteristics of Resonators Excited by a Longitudinal Electric Field.

This study examines the effect of suspensions based on pure glycerol and diamond powder with different concentrations on the characteristics of resonators with a longitudinal electric field. We used two disk resonators made of the quartz and langasite plates with round electrodes on both sides of the plate and resonant frequencies of 4.4 and 4.1 MHz, operating in shear and longitudinal acoustic modes, respectively. Each resonator was mounted on the bottom of a 30 mL liquid container. During the experiments, the container was filled with the suspension under study in such a way that the resonator was completely immersed in the suspension, and the frequency dependences of the real and imaginary parts of the electrical impedance of the resonator were measured. As a result, the shear modulus of the elasticity and shear coefficient of the viscosity of the studied suspensions were determined. The material constants of the suspensions were found by fitting the theoretical frequency dependences of the real and imaginary parts of the electrical impedance of the resonator to the experimentally measured ones, which was calculated using Mason's equivalent circuit. As a result, the dependencies of the density, shear modulus of elasticity, shear viscosity coefficient, and velocity of the shear acoustic wave on the volume concentration of the diamond particles were constructed.

Microbial Acoustical Analyzer for Antibiotic Indication.

In this study, a compact acoustic analyzer for express analysis of antibiotics based on a piezoelectric resonator with a lateral electric field and combined with a computer was developed. The possibility of determining chloramphenicol in aqueous solutions in the concentration range of 0.5-15 µg/mL was shown. Bacterial cells that are sensitive to this antibiotic were used as a sensory element. The change in the electrical impedance modulus of the resonator upon addition of the antibiotic to the cell suspension served as an analytical signal. The analysis time did not exceed 4 min. The correlation of the experimental results of an acoustic sensor with the results obtained using the light phase-contrast microscopy and standard microbiological analysis was established. The compact biological analyzer demonstrated stability, reproducibility, and repeatability of results.

The Radial Electric Field Excited Circular Disk Piezoceramic Acoustic Resonator and Its Properties.

A new type of piezoceramic acoustic resonator in the form of a circular disk with a radial exciting electric field is presented. The advantage of this type of resonator is the localization of the electrodes at one end of the disk, which leaves the second end free for the contact of the piezoelectric material with the surrounding medium. This makes it possible to use such a resonator as a sensor base for analyzing the properties of this medium. The problem of exciting such a resonator by an electric field of a given frequency is solved using a two-dimensional finite element method. The method for solving the inverse problem for determining the characteristics of a piezomaterial from the broadband frequency dependence of the electrical impedance of a single resonator is proposed. The acoustic and electric field inside the resonator is calculated, and it is shown that this location of electrodes makes it possible to excite radial, flexural, and thickness extensional modes of disk oscillations. The dependences of the frequencies of parallel and series resonances, the quality factor, and the electromechanical coupling coefficient on the size of the electrodes and the gap between them are calculated.

Acoustical Slot Mode Sensor for the Rapid Coronaviruses Detection.

A method for the rapid detection of coronaviruses is presented on the example of the transmissible gastroenteritis virus (TGEV) directly in aqueous solutions with different conductivity. An acoustic sensor based on a slot wave in an acoustic delay line was used for the research. The addition of anti-TGEV antibodies (Abs) diluted in an aqueous solution led to a change in the depth and frequency of resonant peaks on the frequency dependence of the insertion loss of the sensor. The difference in the output parameters of the sensor before and after the biological interaction of the TGE virus in solutions with the specific antibodies allows drawing a conclusion about the presence/absence of the studied viruses in the analyzed solution. The possibility for virus detection in aqueous solutions with the conductivity of 1.9-900 µs/cm, as well as in the presence of the foreign viral particles, has been demonstrated. The analysis time did not exceed 10 min.

The Experimental Registration of the Evanescent Acoustic Wave in YX LiNbO3 Plate.

Evanescent acoustic waves are characterized by purely imaginary or complex wavenumbers. Earlier, in 2019 by using a three dimensional (3D) finite element method (FEM) the possibility of the excitation and registration of such waves in the piezoelectric plates was theoretically shown. In this paper the set of the acoustically isolated interdigital transducers (IDTs) with the different spatial periods for excitation and registration of the evanescent acoustic wave in Y-cut X-propagation direction of lithium niobate (LiNbO3) plate was specifically calculated and produced. As a result, the possibility to excite and register the evanescent acoustic wave in the piezoelectric plates was experimentally proved for the first time. The evanescent nature of the registered wave has been established. The theoretical results turned out to be in a good agreement with the experimental ones. The influence of an infinitely thin layer with arbitrary conductivity placed on a plate surface was also investigated. It has been shown that the frequency region of an evanescent acoustic wave existence is very sensitive to the changes of the electrical boundary conditions. The results obtained may be used for the development of the method of the analysis of thin films electric properties based on the study of evanescent waves.

Sensor Based on PZT Ceramic Resonator with Lateral Electric Field for Immunodetectionof Bacteria in the Conducting Aquatic Environment.

A biological sensor for detection and identification of bacterial cells, including a resonator with a lateral electric field based on PZT ceramics was experimentally investigated. For bacterial immunodetection the frequency dependencies of the electric impedance of the sensor with a suspension of microbial cells were measured before and after adding the specific antibodies. It was found that the addition of specific antibodies to a suspension of microbial cells led to a significant change in these frequency dependencies due to the increase in the conductivity of suspension. The analysis of microbial cells was carried out in aqueous solutions with a conductivity of 4.5-1000 µS/cm, as well as in the tap and drinking water. The detection limit of microbial cells was found to be 103 cells/mLand the analysis time did not exceed 4 min. Experiments with non-specific antibodies were also carried out and it was shown that their addition to the cell suspension did not lead to a change in the analytical signal of the sensor. This confirms the ability to not only detect, but also identify bacterial cells in suspensions.

Evaluation of Elastic Properties and Conductivity of Chitosan Acetate Films in Ammonia and Water Vapors Using Acoustic Resonators.

Novel bio-materials, like chitosan and its derivatives, appeal to finding a new niche in room temperature gas sensors, demonstrating not only a chemoresistive response, but also changes in mechanical impedance due to vapor adsorption. We determined the coefficients of elasticity and viscosity of chitosan acetate films in air, ammonia, and water vapors by acoustic spectroscopy. The measurements were carried out while using a resonator with a longitudinal electric field at the different concentrations of ammonia (100-1600 ppm) and air humidity (20-60%). It was established that, in the presence of ammonia, the longitudinal and shear elastic modules significantly decreased, whereas, in water vapor, they changed slightly. At that, the viscosity of the films increased greatly upon exposure to both vapors. We found that the film's conductivity increased by two and one orders of magnitude, respectively, in ammonia and water vapors. The effect of analyzed vapors on the resonance properties of a piezoelectric resonator with a lateral electric field that was loaded by a chitosan film on its free side was also experimentally studied. In these vapors, the parallel resonance frequency and maximum value of the real part of the electrical impedance decreased, especially in ammonia. The results of a theoretical analysis of the resonance properties of such a sensor in the presence of vapors turned out to be in a good agreement with the experimental data. It has been also found that with a growth in the concentration of the studied vapors, a decrease in the elastic constants, and an increase in the viscosity factor and conductivity lead to reducing the parallel resonance frequency and the maximum value of the real part of the electric impedance of the piezoelectric resonator with a lateral electric field that was loaded with a chitosan film. This leads to an increase in the sensitivity of such a sensor during exposure to these gas vapors.

Influence of Humidity on the Acoustic Properties of Mushroom Mycelium Films Used as Sensitive Layers for Acoustic Humidity Sensors.

The influence of humidity on the density, shear elastic module, viscosity, and thickness of the mushroom Pleurotus eryngii and Ganoderma lucidum mycelium films was studied. These data were obtained by comparing the theoretical and experimental frequency dependencies of the complex electrical impedance of bulk acoustic wave (BAW) resonator loaded by mycelium film using the least-squares method. This procedure was performed for the BAW resonator with pointed films for the relative humidity range of 17%-56% at the room temperature. As a result, the changes of the density, shear elastic module, viscosity, and thickness of the films under study, due to the water vapor adsorption, were determined. It has been established that the properties of mycelium films are restored after removing from the water vapor. So, these results show the possibility of using investigated mycelium films as sensitive layers for acoustic humidity sensors.

The study of the influence of the geometry of a lateral electric field resonator on its resonant characteristics.

An experimental study of the dependence of the electrical impedance of a lateral electric field resonator on its thickness and the size of the gap between the electrodes was carried out. The resonator was made of PZT-19 piezoceramics in the form of a rectangular parallelepiped with the shear dimensions of 18 × 20 mm2. Two rectangular electrodes with a gap that varied in the range from 4 to 14 mm were applied on one side of the resonator. For each gap width, the frequency dependences of the real and imaginary parts of the electrical impedance were measured using an impedance analyzer. It has been found that increasing the gap width leads to an increase in the resonant frequency and to an increase in the maximum value of the real part of the impedance. Three series of such experiments were carried out for three values of the resonator thickness: 3.02, 2.38 and 1.9 mm. The resonant characteristics of the resonator were also theoretically analyzed by finite element analysis using two models. One resonator model was based on a two-dimensional finite element method. In this case, the vibration modes that existed due to the finite size of the plate in the direction parallel to the gap between the electrodes were not taken into account. The second model of the resonator used a three-dimensional finite element method, which correctly took into account all vibration modes existing in the resonator. Comparison of theory with experiment has shown that the three-dimensional model provides a better agreement between theoretical and experimental results.

A new liquid sensor based on a piezoelectric resonator with a radial electric field.

The possibility of development a liquid sensor based on a piezoelectric resonator with radial concentric electrodes is shown. The specified resonator has a large number of resonance peaks corresponding to different vibrational modes. The influence of two types of liquid container with distilled water on the resonance characteristics of these vibrational modes is experimentally investigated. As a result, the optimal type of container and two vibrational modes with frequencies of 0.128 and 0.317 MHz were selected, which retain acceptable Q-factors in the presence of distilled water. The dependences of the resonance frequency and the maximum value of the real part of the electrical impedance of these resonance peaks on the conductivity of the liquid were measured. It has been found that with an increase in the conductivity of the liquid, the resonance frequency of the parallel resonance initially remains practically unchanged, but after reaching a certain value of the conductivity of water, it decreases for both resonances. In this case, the maximum value of the real part of the electrical impedance first decreases, reaches a minimum, and then increases in all cases. It is shown that using these dependences as calibration curves, one can unambiguously determine the conductivity of a liquid in the range of 45-5000 µS/cm.

Liquid sensor based on a piezoelectric lateral electric field-excited resonator.

The influence of viscous and conducting liquid on the characteristics of a piezoelectric lateral electric field-excited resonator based on the X-cut lithium niobate plate has been investigated. It has been found that the contact of a free surface of such resonator with conducting or viscous liquid leads to the substantial variation of its electrical impedance/admittance. The analysis has shown the modulus of electrical impedance or admittance at any frequency near the parallel or series resonance to be a parameter unambiguously associated with the conductivity or the viscosity. This parameter is more sensitive to the variation of the liquid conductivity or viscosity as compared to the widely used for this purpose resonant frequency whose variation area is essentially smaller. By this means the liquid conductivity and viscosity affects unambiguously on the change of electrical impedance and admittance modulus whose measurement at a fixed frequency should present no problem in practice. Consequently, the lateral field excited resonator we have described may be employed as a liquid conductivity and viscosity meter with an appropriate graduation.

The study of piezoelectric lateral-electric-field-excited resonator.

The piezoelectric lateral-electric-field-excited resonator based on an X-cut lithium niobate plate has been investigated. Two rectangular electrodes were applied on one side of the plate so that the lateral electric field components were parallel to the crystallographic Y-axis and excited the longitudinal wave in the gap between the electrodes. The region around the electrodes was covered with a special absorbing varnish to suppress the spurious oscillations. The effect of the absorbing coating width on the resonant frequency and Q-factor of the lateral field-excited resonator was studied in detail with the series and parallel resonances for different width of the gap between the electrodes. As a result, we found experimentally the parameter regions of pure resonances and the boundaries of value variation for resonance frequency, Q-factor, and effective electromechanical coupling coefficient.

Acoustic waves in a structure containing two piezoelectric plates separated by an air (vacuum) gap.

This paper presents experimental results for the characteristics of acoustic waves propagating in a structure containing two parallel piezoelectric plates (I and II) separated by an air gap. Plate I, made of Y-X lithium niobate, contained two interdigital transducers that excited and received an acoustic wave with shear-horizontal polarization. Piezoelectric plate II, made of lithium niobate, was placed above and between the transducers, separated by a fixed gap. For its certain orientation, the amplitude-frequency characteristic showed sharply defined resonant attenuation peaks, which were situated at an equidistant separation from each other. The depth of the peaks was observed to decrease with a wider gap between the plates. It has been stated that these peaks are associated with the resonant reflections of a slot acoustic wave across the width of plate II. Experimentally determined phase velocities and electromechanical coupling coefficient for the slot wave in the structure under study are in a good agreement with theoretical values for various crystallographic orientations of plate II. A comparison between the experimental and theoretical results has allowed us to state two conditions for the slot wave to exist. The structures described may be employed for noncontact excitation of acoustic waves in the plates and for the development of various liquid, gas, and temperature sensors.