RESUMO
The use of photochromism to enhance the anti-counterfeiting of a wide range of economic goods is an intriguing prospect. Creating a translucent anti-counterfeiting nanocomposite is critical to improving the engineering procedures of the encoding materials. Herein, we use electrospinning to produce anti-counterfeiting nanofibrous films from nanoparticles of rare-earth aluminate (NREA) and recycled poly(ethylene terephthalate) (PET). Different nanofiber films with distinct emission properties were created using different ratios of NREA. The ultraviolet (UV)-induced photochromism of the NREA@PET nanofibers was proved. Immobilizing NREA at the nanoscale ensures better dispersion without agglomeration in the PET nanofibrous matrix, which is essential for the development of transparent NREA@PET films. Diameters of 4-13 nm for NREA were shown using transmission electron microscopy. X-ray fluorescence spectroscopy, energy-dispersive X-ray spectroscopy, Fourier-transform infrared spectroscopy, scanning electron microscopy, elemental mapping, and other techniques were used to investigate the photochromic nanofibers' morphology, elemental contents, optical transmittance, and mechanical performance. It was observed that the nanofiber diameter in NREA@PET was between 150 and 250 nm. Excitation and emission bands of electrospun NREA@PET nanofibrous films were monitored at 365 and 518 nm, respectively. The superhydrophobicity of NREA@PET increased with increasing NREA concentration. The transparent nanofibers exhibited fast and reversible dual-mode fluorescent photochromism to green emission without fatigue when stimulated beneath a UV source. Using the present anti-counterfeiting films can be regarded as a simple technique to develop flexible materials to launch an ideal marketplace with affordable societal and economic advantages.
Assuntos
Nanofibras , Ácidos Ftálicos , Nanofibras/química , Polietilenotereftalatos , EtilenosRESUMO
The use of photochromism to increase the credibility of consumer goods has shown great promise. To provide mechanically dependable anticounterfeiting nanofibres, it has also been critical to improve the engineering processes of authentication patterns. Mechanically robust and photoluminescent electrospun poly(ethylene oxide)/glass (PGLS) nanofibres (150-350 nm) immobilized with nanoparticles of lanthanide-doped aluminate (NLA; 8-15 nm) were developed using electrospinning technology for anticounterfeiting purposes. The provided nanofibrous membranes changed colour from transparent to green when irradiated with ultraviolet light. By delivering NLA with homogeneous distribution without aggregations, we were able to keep the nanofibrous membrane transparent. When excited at 365 nm, NLA@PGLS nanofibres showed an emission intensity at 517 nm. The hydrophobicity of NLA@PGLS nanofibres improved by raising the pigment concentration as the contact angle was increased from 146.4° to 160.3°. After being triggered by ultraviolet light, NLA@PGLS showed quick and reversible photochromism without fatigue. It was shown that the suggested method can be applied to reliably produce various anticounterfeiting materials.
Assuntos
Vidro , Nanofibras , Polietilenoglicóis , Raios Ultravioleta , Nanofibras/química , Polietilenoglicóis/química , Vidro/química , Tamanho da Partícula , Propriedades de SuperfícieRESUMO
Nano-biocomposites of inorganic and organic components wereprepared to produce long-persistent phosphorescent artificial nacre-like materials. Biodegradable polylactic acid (PLA), graphene oxide (GO), and nanoparticles (13-20 nm) of lanthanide-doped aluminate pigment (NLAP) were used in a simple production procedure of an organic/inorganic hybrid nano-biocomposite. Both polylactic acid and GO nanosheets were chemically modified to form covalent and hydrogen bonding. The high toughness, good tensile strength, and great endurance of those bonds were achieved by their interactions at the interfaces. Long-persistent and reversible photoluminescence was shown by the prepared nacre substrates. Upon excitation at 365 nm, the nacre substrates generated an emission peak at 517 nm. When ultraviolet light was shone on luminescent nacres, they displayed a bright green colour. The high superhydrophobicity of the generated nacres was obtained without altering their mechanical characteristics.
Assuntos
Grafite , Nácar , PoliésteresRESUMO
A smart nanocomposite adhesive was created to facilitate a simple production of long-persistent photoluminescent and hydrophobic commercial products. Even after being left in the dark for up to 90 min, the created photoluminescent adhesive agent continued to generate light. A surface-specific nanocomposite adhesive agent consisting of lanthanide-activated strontium aluminate (LSA) nanoparticles (NPs; 5-14 nm) immobilized in the environmentally friendly Arabic gum (AG) was developed. A light-transmitting nanocomposite adhesive agent was manufactured by dispersing LSA nanoparticles evenly across the AG matrix without agglomeration. An excitation peak at 365 nm and an emission wavelength at 519 nm were observed for the prepared adhesives at different concentrations of LSA NPs. The emission spectra showed either fluorescence or afterglow phosphorescence, depending on the LSA ratio. The photochromic transition from colourless to green beneath an ultraviolet (UV) lamp and greenish yellow in a dark room was tracked. The LSA NPs in the Arabic gum matrix imparted enhanced hydrophobicity and scratch resistance to the LSA@AG nanocomposite. The LSA@AG nanocomposite demonstrated excellent durability and photostability. This study confirmed that the mass production of smart adhesives for applications such as smart windows, smart packaging, and safety directional signs in buildings is possible.
Assuntos
Elementos da Série dos Lantanídeos , Nanopartículas , Interações Hidrofóbicas e HidrofílicasRESUMO
Poly(vinyl chloride) (PVC) was reinforced with electrospun glass nanofibres (EGN) to develop photochromic and afterglow materials such as smart windows and anti-counterfeiting prints. A colourless electrospun glass nanofibres@poly(vinyl chloride) (EGN@PVC) sheet was prepared by physical integration of lanthanide-doped aluminate nanoparticles (LANP). The low concentrations of LANP in the photochromic and photoluminescent EGN@PVC hybrids displayed fluorescence emission with instant reversibility. EGN@PVC with the highest phosphor concentrations showed persistent phosphorescence emission with slow reversibility. Based on the results of the Commission Internationale de l'éclairage Laboratory and luminescence spectroscopy, the translucent EGN@PVC samples became green in the presence of ultraviolet illumination and greenish-yellow in the absence of light. According to scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses, the morphological study of EGN and LANP showed diameters of 75-95 and 11-19 nm, respectively. The morphology of the EGN@PVC substrates was studied using SEM, X-ray fluorescence, and energy-dispersive X-ray spectroscopy. The mechanical characteristics of PVC were enhanced by reinforcement with EGN as a roughening agent. When comparing the scratching resistance of LANP-free substrate to photoluminescent EGN@PVC substrates, it was observed that the latter was much superior. The photoluminescence spectra were reported to have an emission peak at 519 nm when excited at 365 nm. These findings demonstrated that the luminous transparent EGN@PVC composites had improved superhydrophobic and UV-blocking characteristics.
Assuntos
Nanofibras , Cloreto de Vinil , Polímeros , Raios Ultravioleta , LuminescênciaRESUMO
The rapid growth of the dye and textile industry has raised significant public concerns regarding the pollution caused by dye wastewater, which poses potential risks to human health. In this study, we successfully improved the adsorption efficiency of activated carbon derived from pomegranate peel waste (PPAC) through a single-step and surface modification approach using 5-sulfonate-salicylaldehyde sodium salt. This innovative and effective sulfonation approach to produce sulfonated activated carbon (S-PPAC) proved to be highly effective in removing crystal violet dye (CV) from polluted water. The prepared PPAC and S-PPAC were characterized via FESEM, EDS, FTIR and BET surface area. Characterization studies confirmed the highly porous structure of the PPAC and its successful surface modification, with surface areas reaching 1180.63 m2/g and 740.75 m2/g for the PPAC and S-PPAC, respectively. The maximum adsorption capacity was achieved at 785.53 mg/g with the S-PPAC, an increase of 22.76% compared to the PPAC at 45 °C. The isothermic adsorption and kinetic studies demonstrated that the adsorption process aligned well with the Freundlich isotherm model and followed the Elovich kinetic model, respectively. The thermodynamic study confirmed that the adsorption of CV dye was endothermic, spontaneous and thermodynamically favorable onto PPAC and S-PPAC.
RESUMO
The main objective of this work is to develop biodegradable active films through the combination of the extracts with different solvents sourced from Eucalyptus citriodora leaves, with films made of chitosan (Cs) and polyvinylpyrrolidone (PVP). Chromatographic profiling investigations were carried out to examine the antibacterial characteristics of E. citriodora extracts before their direct incorporation into the polymer films. At this point, the potent antimicrobial properties of the phenol compounds and bioactive components demonstrated an antibacterial activity that was particularly noticeable at a hexane resolution. Different morphological characteristics were seen on films made from these solvent extracts, such as Cs/PVP-AE, Cs/PVP-EAE, and Cs/PVP-HE, when scanning electron microscopy was used. Numerous other outcomes of all the interactions between the extract particles and the film were shown by the pores defined by the Cs/PVP film's porous nature. The addition of the extracts, either alone or in combination, greatly enhanced the Cs/NC/PVP films' mechanical characteristics. It has also been shown that adding plant extracts greatly increased the antibacterial activity of these films. These findings reveal that Cs/PVP films loaded with extract may be utilized as more environmentally acceptable substitutes for possible food packaging application by increasing shelf life of food products.
Assuntos
Antibacterianos , Quitosana , Eucalyptus , Extratos Vegetais , Povidona , Quitosana/química , Eucalyptus/química , Antibacterianos/farmacologia , Antibacterianos/química , Povidona/química , Extratos Vegetais/química , Extratos Vegetais/farmacologia , Embalagem de Alimentos , Testes de Sensibilidade MicrobianaRESUMO
This study presents a novel approach in the synthesis and characterization of nanocomposites comprising cationic chitosan (CCS) blended with varying concentrations of silver nanoparticles/montmorillonite (AgNPs/MMT). AgNPs/MMT was synthesized using soluble starch as a reducing and stabilizing agent. Subsequently, nanocomposites, namely CCS/AgMMT-0, CCS/AgMMT-0.5, CCS/AgMMT-1.5, and CCS/AgMMT-2.5, were developed by blending 2.5 g of CCS with 0, 0.5, 1.5, and 2.5 g of AgNPs/MMT, respectively, and the corresponding nanocomposites were prepared using ball milling technique. Transmission electron microscopy (TEM) analysis revealed the formation of nanocomposites that exhibiting nearly spherical morphologies. Dynamic light scattering (DLS) measurements displayed average particle sizes of 1183 nm, 131 nm, 140 nm, and 188 nm for CCS/AgMMT-0, CCS/AgMMT-0.5, CCS/AgMMT-1.5, and CCS/AgMMT-2.5, respectively. The narrow polydispersity index (~0.5) indicated uniform particle size distributions across the nanocomposites, affirming monodispersity. Moreover, the zeta potential values exceeding 30 mV across all nanocomposites that confirmed their stability against agglomeration. Notably, CCS/AgMMT-2.5 nanocomposite exhibited potent antibacterial and antibiofilm properties against diverse pipeline materials. Findings showed that after 15 days of incubation, the highest populations of biofilm cells, Pseudomonas aeruginosa biofilm, developed over UPVC, MDPE, DCI, and SS, with corresponding HPCs of 4.79, 6.38, 8.81, and 7.24 CFU/cm2. The highest cell densities of Enterococcus faecalis biofilm in the identical situation were 4.19, 5.89, 8.12, and 6.9 CFU/cm2. The nanocomposite CCS/AgMMT-2.5 exhibited the largest measured zone of inhibition (ZOI) against both P. aeruginosa and E. faecalis, with measured ZOI values of 19 ± 0.65 and 17 ± 0.21 mm, respectively. Remarkably, the research indicates that the youngest biofilm exhibited the most notable rate of inactivation when exposed to a dose of 150 mg/L, in comparison to the mature biofilm. These such informative findings could offer valuable insights into the development of effective antibiofilm agents and materials applicable in diverse sectors such as water treatment facilities, medical devices, and industrial pipelines.
Assuntos
Quitosana , Nanopartículas Metálicas , Nanocompostos , Prata/farmacologia , Bentonita/farmacologia , Quitosana/farmacologia , Antibacterianos/farmacologia , Cátions/farmacologia , Biofilmes , Testes de Sensibilidade MicrobianaRESUMO
Recent years have seen an increase in research on biodiesel, an environmentally benign and renewable fuel alternative for traditional fossil fuels. Biodiesel might become more cost-effective and competitive with diesel if a solid heterogeneous catalyst is used in its production. One way to make biodiesel more affordable and competitive with diesel is to employ a solid heterogeneous catalyst in its manufacturing. Based on X-ray diffraction (XRD) and Fourier Transform infrared spectroscopy (FTIR), the researchers in this study proved their hypothesis that iron oxide core-shell nanoparticles were generated during the green synthesis of iron-based nanoparticles (FeNPs) from Camellia Sinensis leaves. The fabrication of spherical iron nanoparticles was successfully confirmed using scanning electron microscopy (SEM). As a heterogeneous catalyst, the synthesised catalyst has shown potential in facilitating the conversion of algae oil into biodiesel. With the optimal parameters (0.5 weight percent catalytic load, 1:6 oil-methanol ratio, 60 °C reaction temperature, and 1 h and 30 min reaction duration), a 93.33% yield was attained. This may be due to its acid-base property, chemical stability, stronger metal support interaction. Furthermore, the catalyst was employed for transesterification reactions five times after regeneration with n-hexane washing followed by calcination at 650 °C for 3 h.
Assuntos
Biocombustíveis , Camellia sinensis , Folhas de Planta , Folhas de Planta/química , Catálise , Camellia sinensis/química , Ferro/química , Nanopartículas Metálicas/química , Difração de Raios X , Esterificação , Espectroscopia de Infravermelho com Transformada de FourierRESUMO
The preparation of metallic nanostructures supported on porous carbon materials that are facile, green, efficient, and low-cost is desirable to reduce the cost of electrocatalysts, as well as reduce environmental pollutants. In this study, a series of bimetallic nickel-iron sheets supported on porous carbon nanosheet (NiFe@PCNs) electrocatalysts were synthesized by molten salt synthesis without using any organic solvent or surfactant through controlled metal precursors. The as-prepared NiFe@PCNs were characterized by scanning and transmission electron microscopy (SEM and TEM), X-ray diffraction, and photoelectron spectroscopy (XRD and XPS). The TEM results indicated the growth of NiFe sheets on porous carbon nanosheets. The XRD analysis confirmed that the Ni1-xFex alloy had a face-centered polycrystalline (fcc) structure with particle sizes ranging from 15.5 to 30.6 nm. The electrochemical tests showed that the catalytic activity and stability were highly dependent on the iron content. The electrocatalytic activity of catalysts for methanol oxidation demonstrated a nonlinear relationship with the iron ratio. The catalyst doped with 10% iron showed a higher activity compared to the pure nickel catalyst. The maximum current density of Ni0.9Fe0.1@PCNs (Ni/Fe ratio 9:1) was 190 mA/cm2 at 1.0 M of methanol. In addition to the high electroactivity, the Ni0.9Fe0.1@PCNs showed great improvement in stability over 1000 s at 0.5 V with a retained activity of 97%. This method can be used to prepare various bimetallic sheets supported on porous carbon nanosheet electrocatalysts.
RESUMO
Biomaterials-based adsorbents have emerged as a sustainable and promising solution for water purification, owing to their eco-friendly nature and remarkable adsorption capacities. In this study, a biocomposite hydrogel was prepared by the incorporation of activated carbon derived from pomegranate peels (PPAC) in tragacanth gum (TG). The hydrogel biocomposite (PPAC/TG) showed a porous structure, a negative surface charge at a pH of more than 4.9, and good stability in aqueous media. The adsorption properties of the PPAC/TG hydrogel biocomposite were assessed for the removal of crystal violet dye (CV) from aqueous solutions using a batch adsorption. The equilibrium adsorption data followed the Sips isotherm model, as supported by the calculated R2 (>0.99), r-χ2 (<64), and standard error values (<16). According to the Sips model, the maximum values of the adsorption capacity of PPAC/TG were 455.61, 470.86, and 477.37 mg/g at temperatures of 25, 30, and 35 °C, respectively. The adsorption kinetic of CV onto the PPAC/TG hydrogel biocomposite was well described by the pseudo-second-order model with R2 values more than 0.999 and r-χ2 values less than 12. Thermodynamic studies confirmed that the CV dye adsorption was spontaneous and endothermic. Furthermore, the prepared hydrogel exhibited excellent reusability, retaining its adsorption capacity even after being used more than five times. Overall, this study concludes that the prepared PPAC/TG exhibited a significant adsorption capacity for cationic dyes, indicating its potential as an effective and eco-friendly adsorbent for water treatment.
RESUMO
The necessity for reliable and efficient multifunctional optical and optoelectronic devices is always calling for the exploration of new fertile materials for this purpose. This study leverages the exploitation of dyed environmentally friendly biopolymeric thin films as a potential optical absorber in the development of multifunctional opto-(electronic) and solar cell applications. Uniform, stable thin films of dyed chitosan were prepared using a spin-coating approach. The molecular interactivity between the chitosan matrix and all the additive organic dyes was evaluated using FTIR measurements. The color variations were assessed using chromaticity (CIE) measurements. The optical properties of films were inspected using the measured UV-vis-NIR transmission and reflection spectra. The values of the energy gap and Urbach energy as well as the electronic parameters and nonlinear optical parameters of films were estimated. The prepared films were exploited for laser shielding as an attenuated laser cut-off material. In addition, the performance of the prepared thin films as an absorbing organic layer with silicon in an organic/inorganic heterojunction architecture for photosensing and solar energy conversion applicability was studied. The current-voltage relation under dark and illumination declared the suitability of this architecture in terms of responsivity and specific detectivity values for efficient light sensing applications. The suitability of such films for solar cell fabrications is due to some dyed films achieving open-circuit voltage and short-circuit current values, where Saf-dyed films achieved the highest Voc (302 mV) while MV-dyed films achieved the highest Jsc (0.005 mA/cm2). Finally, based on all the obtained characterization results, the engineered natural cost-effective dyed films are considered potential active materials for a wide range of optical and optoelectronic applications.
RESUMO
Ruthenium (Ru) electrocatalysts suffer from excessive aggregation during the hydrogen evolution reaction (HER), which hinders their practical application for hydrogen production. Hexagonal boron nitride (h-BN) is a potential carrier that could solve the above problem, but its wide band gap and low conductivity become obstacles. Herein, we provide a new, facile, low-cost, and effective strategy (killing two birds with one stone) to overcome the above issues. After modifying h-BN with reduced graphene oxide (rGO), a small amount of Ru nanoparticles (NPs) (2.2 %) are dispersed into BN with approximately uniform distribution and size control of Ru nanoparticles (â¼3.85 nm). The strong synergy between Ru NPs and BN@C in the optimal Ru/BN@C (Ru wt.% = 2.22 %) electrocatalyst endows it an outstanding HER activity, with small HER overpotentials (η10 = 32 mV, 35 mV) and low Tafel slopes (33.89 mV dec-1, 37.66 mV dec-1) in both 1 M KOH and 0.5 M H2SO4 media, respectively, along with good long-term stability for 50 h. Based on density functional theory (DFT) calculations, the addition of Ru to BN has been successful in creating fresh active sites for H*, with good possible adsorption/desorption ability (ΔGH* = -0.24 eV) while preserving low water dissociation (ΔGb = 0.46 eV) in an alkaline environment. As a result, the Ru/BN composite exhibits outstanding HER activity in both acidic and alkaline conditions. Furthermore, this study provides, for the first time, a template-free strategy to develop a good and low-cost supporter (BN) for dispersing other noble metals and the formation of highly efficient HER/OER electrocatalysts.
RESUMO
Innovative and facile methods for the preparation of metal nanoparticles (MNPs) with A highly uniform distribution and anchored on a unique substrate are receiving increasing interest for the development of efficient and low-cost catalysts in the field of alternative and sustainable energy technologies. In this study, we report a novel and facile metal-ions adsorption-pyrolysis method based on a hydrogel nanocomposite for the preparation of well-distributed nickel nanoparticles on 3D porous carbon frameworks (Ni@PCFs). The pyrolysis temperature effect on electrocatalytic activity toward methanol oxidation and catalyst stability was investigated. Physicochemical characterizations (SEM, TEM, and XRD) were used to determine the morphology and composition of the prepared electrocatalyst, which were then linked to their electrocatalytic activity. The experimental results indicate that the catalyst synthesized by pyrolysis at 800 °C (Ni@PCFs-8) exhibits the highest electrocatalytic activity for oxidation of methanol in alkaline media. Additionally, prepared Ni@PCFs-8 displays a remarkable increase in electrocatalytic activity after activation in 1 M KOH and excellent stability. The adsorption-pyrolysis pathway ensures that the Ni NPs are trapped in the PCFs, which can provide highly reactive surface sites. This work may provide a facile and effective strategy for preparing uniformly distributed metallic NPs on a 3D PCF substrate with high catalytic activity for energy applications.
RESUMO
In this study six new s-triazine bishydrazino and bishydrazido-based polymers were synthesized via condensation of bishydrazino s-triazine derivatives with terephthaldehyde or via nucleophilic substitution of dichloro-s-triazine derivatives with terephthalic acid hydrazide. The synthesized polymers were characterized by different techniques. The new polymers displayed good thermal behavior with great values in terms of limited oxygen indexed (LOI) 27.50%, 30.12% for polymers 5b,c (bishydrazino-s-triazine based polymers) and 27.23%, 29.86%, 30.85% for polymers 7a-c (bishydrazido-s-triazine based polymers) at 800 °C. Based on the LOI values, these polymers could be classified as flame retardant and self-extinguishing materials. The thermal results also revealed that the type of substituent groups on the triazine core has a considerable impact on their thermal behavior. Accordingly, the prepared polymers were mixed with ammonium polyphosphate (APP) in different proportions to form an intumescent flame-retardant (IFRs) system and were introduced into polypropylene (PP) to improve the flame-retardancy of the composites. The best results were obtained with a mass ratio of APP: 5a-c or 7a-c of 2:1, according to the vertical burning study (UL-94). In addition, the presence of 25% "weight ratio" of IFR in the composite showed great impact and passed UL-94 V-0 and V-1 tests.
RESUMO
The fabrication of electrocatalysts with high catalytic activity, high durability and low cost towards urea oxidation by a facile method is a great challenge. In this study, non-precious NiCoFe trimetallic supported on porous carbon (NiCoFe@PC) was prepared via gelation and pyrolysis method, presenting a remarkable electrocatalytic activity with low onset potential for urea oxidation in an alkaline medium. Field-emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) were used to clarify the morphology of the NiCoFe@PC nanostructure and its nanoparticle size of 17.77 nm. The prepared catalyst with the composition ratio of 24.67, 5.92 and 5.11% for Ni, Fe and Co, respectively, with highly crystalline nanoparticles, fixed on porous carbon, according to energy-dispersive X-ray (EDX) and X-ray diffraction (XRD) analysis. The FeCoNi@PC catalyst showed a catalytic activity of 44.65 mA/cm2 at 0.57 V vs. Ag/AgCl and a low onset potential of 218 mV, which is superior to many other transition bi/trimetallic-based catalysts previously reported.
RESUMO
The development of bioactive polymer nanofiber sheets based on eco-friendly components is required to meet the needs of various medical applications as well as to preserve the environment. This study aimed to fabricate biohybrid nanofibers based on water-soluble polymers and aqueous extract of myrrh. The myrrh extract was incorporated into poly(vinyl alcohol)/tragacanth gum nanofiber mats (myrrh@PVA/TG) by the green electrospinning technique. Various characteristics of the prepared fibers such as morphology, fiber diameter distribution, crystallinity, and thermal stability were studied. The results confirmed that the morphology of biohybrid nanofibers was uniform without beads and tragacanth gum plays an important role in controlling the average diameter of fibers and the crystallinity. The antibacterial properties of the developed biohybrid nanofibers were investigated against common pathogens of Gram-positive and Gram-negative bacteria by the standard disc diffusion method. A significant antibacterial activity was observed toward bacterial strains after incorporation of aqueous myrrh extract into nanofibers, which increased on increasing the extract ratio. Due to their eco-friendly components and significant antibacterial activity, the prepared biohybrid nanofibers will open new avenues toward incorporating aqueous herbal extracts into degradable polymer fibers for use in many antibacterial applications.
RESUMO
Tungsten oxide (WO3) as an efficient heterogeneous catalyst was prepared via a simple hydrothermal route for the synthesis of a wide range of bioactive heterocyclic compounds. The present investigation deals with the rapid and low-cost synthesis of C-3-alkylated 4-hydroxycoumarin, chromene, and xanthene derivatives. WO3 nanorods (NRs) are successfully envisaged to catalyze desired transformations, demonstrating the wide range of their potential applications in catalysis. Synthetic transformation details, smallest catalytic amounts, excellent product yields, and plausible reaction mechanisms for the formation of these heterocyclic scaffolds are elicidated. As-prepared WO3 NRs are characterized to confirm their structural, chemical, and morphological parameters by X-ray diffraction, X-ray photoelectron spectroscopy, and field emission scanning electron microscopy measurements, respectively. We discuss the factors that govern the formation of products, and the active role of WO3 NRs, which are essential for the activation of substrates in the present study of thermal conditions. Herein, detailed synthesis and spectroscopic information of the prepared compounds are reported.
Assuntos
Compostos Heterocíclicos/química , Nanotubos/química , Óxidos/química , Tungstênio/química , Catálise , Química Verde , Porosidade , Propriedades de SuperfícieRESUMO
The burst release of drug is a problem associated with the use of common blending electrospinning. This problem can be avoided via fabrication of core-shell nanofibers where drug can be coated with polymer nanofibers as a shell. Moreover, there is a need to provide wound dressing with prolonged system of sustained release to accelerate the recovery of the wound. Currently, electrospun ciprofloxacin loaded poly(acrylic acid)/Dextran (Cipro@PAA/Dex) core-shell nanofibers can be prepared in green method using emulsion electrospinning. For comparison study, blend electrospun nanofibers (Cipro/PAA/Dex) was also prepared. The entrapment of drug into the polymeric material and the interaction between polymer blends were confirmed by FT-IR. Moreover, DSC was used to identify the type of interaction between polymeric chains. Field emission scanning electron microscope (FE-SEM) was used to study the nanofiber morphology and transmission electron microscope (TEM) and confocal laser scanning microscope (CLSM) were used to confirm the formation of core-shell structure. In vitro drug release profile was monitored by UV-Vis spectrophotometer and the results showed that Cipro@PAA/Dex exhibited controlled release behavior whereas Cipro/PAA/Dex showed burst release behavior. Moreover, the release mechanism is kinetically followed diffusion.
Assuntos
Nanofibras , Resinas Acrílicas , Bandagens , Preparações de Ação Retardada , Dextranos , Emulsões , Espectroscopia de Infravermelho com Transformada de FourierRESUMO
The high surface area and porosity of self-nitrogen-doped porous carbons (SNPCs) nominates them for potential application in water treatment due to their high efficiency towards the removal of various pollutants. In this study, SNPCs were fabricated from poly(1,5-diaminonaphthalene) (P(1,5-DANPh) by single and simultaneous carbonization at the activation step at different temperatures (600, 700, and 800 °C). The carbonization's temperature plays a vital role in controlling the nitrogen-doping, surface area, porosity, and morphology of SNPCs. The SNPCs-7 sample prepared at 700 °C showed the highest surface area (1678.8 m2 g-1) with pore volume (0.943 cm3 g-1) with a micro/meso porous structure. The prepared SNPCs were used as an effective adsorbent for removal of crystal violet dye (CV) from contaminated water. SNPCs-7 showed the highest adsorption of 487.53 mg g-1 and the adsorption capacity of the SNPCs samples follows the order SNPCs-7 > SNPCs-8 > SNPCs-6, which is consistent with the results of their surface area and porosity. The adsorption for CV dye followed Freundlich isotherm models and a pseudo second order kinetic model. The negative values of Gipps free energy (ΔG°) and positive value of enthalpy (ΔH°) indicated that the adsorption of CV dye onto the surface of SNPCs was a spontaneous and endothermic process, respectively. Based on the results, the adsorption mechanism of CV dye onto the surface of SNPCs was proposed.