The character and distribution of physical contaminants found in soil previously treated with mixed waste organic outputs and garden waste compost.

The re-use of waste materials by application to land is an increasingly common practice around the world, but where municipal solid waste materials are applied, it is almost inevitable that physical contaminants such as glass and plastic will be added to the soil. In many jurisdictions, there are prescribed limits for the amounts of physical contaminants that may be present in these materials, but there is little information on whether these limits safeguard soil functional condition. Here, physical contamination of soil is described after varying rates of a mixed waste organic output (MWOO) and garden waste compost (GWC) were incorporated into field plots. At application rates of 100 and 200 t/ha, both treatments resulted in a coarsening of the topsoil particle size distribution, but only in the MWOO-treated soils were physical contaminants largely responsible for this. The physical contaminant particles present were found only to the depth of cultivation, and included glass, rigid and film plastics, and synthetic fibres. These contaminants were most commonly observed in the gravel and coarse sand-sized fractions, and in those soils treated with the highest rates of MWOO application. Physical contaminant particles acted as both enveloping and nucleating agents for mineral grains and organic matter, and blocked some pores. Although soil physical condition is usually improved by the incorporation of organic matter, the extent of pore blockage evident here suggests that soil physical functions such as water percolation may be affected as the organic matter is broken down and the soil undergoes natural re-consolidation.

Application of phytotoxicity data to a new Australian soil quality guideline framework for biosolids.

To protect terrestrial ecosystems and humans from contaminants many countries and jurisdictions have developed soil quality guidelines (SQGs). This study proposes a new framework to derive SQGs and guidelines for amended soils and uses a case study based on phytotoxicity data of copper (Cu) and zinc (Zn) from field studies to illustrate how the framework could be applied. The proposed framework uses normalisation relationships to account for the effects of soil properties on toxicity data followed by a species sensitivity distribution (SSD) method to calculate a soil added contaminant limit (soil ACL) for a standard soil. The normalisation equations are then used to calculate soil ACLs for other soils. A soil amendment availability factor (SAAF) is then calculated as the toxicity and bioavailability of pure contaminants and contaminants in amendments can be different. The SAAF is used to modify soil ACLs to ACLs for amended soils. The framework was then used to calculate soil ACLs for copper (Cu) and zinc (Zn). For soils with pH of 4-8 and OC content of 1-6%, the ACLs range from 8 mg/kg to 970 mg/kg added Cu. The SAAF for Cu was pH dependant and varied from 1.44 at pH 4 to 2.15 at pH 8. For soils with pH of 4-8 and OC content of 1-6%, the ACLs for amended soils range from 11 mg/kg to 2080 mg/kg added Cu. For soils with pH of 4-8 and a CEC from 5-60, the ACLs for Zn ranged from 21 to 1470 mg/kg added Zn. A SAAF of one was used for Zn as it concentrations in plant tissue and soil to water partitioning showed no difference between biosolids and soluble Zn salt treatments, indicating that Zn from biosolids and Zn salts are equally bioavailable to plants.

Modeling the toxicity of copper and zinc salts to wheat in 14 soils.

Interest is mounting in developing and utilizing soil-specific soil quality guidelines. This requires quantifying the effects that soil physicochemical properties have on various ecotoxicological endpoints, including phytotoxicity. To this end, 14 agricultural soils from Australia with differing soil properties were spiked with copper (Cu) and zinc (Zn) salts and used to conduct 21-d plant growth inhibition tests using wheat (Triticum aestivum L.) in pot trials. The toxicity of Cu and Zn was similar with 10% effect concentration (EC10) values ranging from 110 to 945 and from 235 to 965 mg/kg, respectively, while the corresponding median effect concentration (EC50) values ranged from 240 to 1,405 and 470 to 1,745 mg/kg, respectively. Copper toxicity values (EC10, EC20, and EC50) were best modeled by the logarithm of cation exchange capacity (CEC) and either soil pH or electrical conductivity. Zinc EC50 and EC20 values were best modeled using the logarithm of CEC, while the EC10 data were best modeled using soil pH and the logarithm of organic carbon. These models generally estimated toxicity within a factor of two of the measured values.

Bioavailability of zinc and copper in biosolids compared to their soluble salts.

For essential elements, such as copper (Cu) and zinc (Zn), the bioavailability in biosolids is important from a nutrient release and a potential contamination perspective. Most ecotoxicity studies are done using metal salts and it has been argued that the bioavailability of metals in biosolids can be different to that of metal salts. We compared the bioavailability of Cu and Zn in biosolids with those of metal salts in the same soils using twelve Australian field trials. Three different measures of bioavailability were assessed: soil solution extraction, CaCl(2) extractable fractions and plant uptake. The results showed that bioavailability for Zn was similar in biosolid and salt treatments. For Cu, the results were inconclusive due to strong Cu homeostasis in plants and dissolved organic matter interference in extractable measures. We therefore recommend using isotope dilution methods to assess differences in Cu availability between biosolid and salt treatments.

Models for the field-based toxicity of copper and zinc salts to wheat in 11 Australian soils and comparison to laboratory-based models.

Laboratory-based relationships that model the phytotoxicity of metals using soil properties have been developed. This paper presents the first field-based phytotoxicity relationships. Wheat (Triticum aestivum L.) was grown at 11 Australian field sites at which soil was spiked with copper (Cu) and zinc (Zn) salts. Toxicity was measured as inhibition of plant growth at 8 weeks and grain yield at harvest. The added Cu and Zn EC10 values for both endpoints ranged from approximately 3 to 4760 mg/kg. There were no relationships between field-based 8-week biomass and grain yield toxicity values for either metal. Cu toxicity was best modelled using pH and organic carbon content while Zn toxicity was best modelled using pH and the cation exchange capacity. The best relationships estimated toxicity within a factor of two of measured values. Laboratory-based phytotoxicity relationships could not accurately predict field-based phytotoxicity responses.