Photothermal Conversion of the Oleophilic PVDF/Ti3C2Tx Porous Foam Enables Non-Aqueous Liquid System Applicable Actuator.

Various physical and chemical reaction processes occur in non-aqueous liquid systems, particularly in oil phase systems. Therefore, achieving efficient, accurate, controllable, and cost-effective movement and transfer of substances in the oil phase is crucial. Liquid-phase photothermal actuators (LPAs) are commonly used for material transport in liquid-phase systems due to their remote operability and precise control. However, existing LPAs typically rely on materials like hydrogels and flexible polymers, commonly unsuitable for non-aqueous liquids. Herein, a 3D porous poly(vinylidene fluoride) (PVDF)/Ti3C2Tx actuator is developed using a solvent displacement method. It demonstrates directional movement and controlled material transport in non-aqueous liquid systems. When subject to infrared light irradiation (2.0 W cm-2), the actuator achieves motion velocities of 7.3 and 6 mm s-1 vertically and horizontally, respectively. The actuator's controllable motion capability is primarily attributed to the foam's oil-wettable properties, 3D porous oil transport network, and the excellent photothermal conversion performance of Ti3C2Tx, facilitating thermal diffusion and the Marangoni effect. Apart from multidimensional directions, the actuator enables material delivery and obstacle avoidance by transporting and releasing target objects to a predetermined position. Hence, the developed controllable actuator offers a viable solution for effective motion control and material handling in non-aqueous liquid environments.

Precisely Controlled Polymerization of Two-Dimensional Conducting Polymers in Quasi-Liquid Layer Enables Ultrahigh Sensing Performance.

Gas sensors based on conducting polymers offer great potential for high-performance room temperature applications due to their cost-effectiveness, high-sensitivity, and operational advantage. However, their current performance is limited by the deficiency of control in conventional polymerization methods, leading to poor crystallinity and inconsistent material properties. Here, the quasi-liquid layer (QLL) on the ice surface acts as a self-regulating nano-reactor for precise control of thermodynamics and kinetics in the polymerization, resulting in a 7.62 nm thick two-dimensional (2D) polyaniline (PANI) film matching the QLL thickness. The ultra-thin film optimizes the exposure of active sites, enhancing the detection of analyte gases at low concentrations. It is validated by fabricating a chemiresistive gas sensor with the 2D PANI film, demonstrating stable room-temperature detection of ammonia down to 10 ppt in ambient air with an impressive 10% response. This achievement represents the highest sensitivity among sensors of this kind while maintaining excellent selectivity and repeatability. Moreover, the QLL-controlled polymerization strategy offers an alternative route for precise control of the polymerization process for conducting polymers, enabling the creation of advanced materials with enhanced properties.

Metal Halides for High-Capacity Energy Storage.

High-capacity electrochemical energy storage systems are more urgently needed than ever before with the rapid development of electric vehicles and the smart grid. The most efficient way to increase capacity is to develop electrode materials with low molecular weights. The low-cost metal halides are theoretically ideal cathode materials due to their advantages of high capacity and redox potential. However, their cubic structure and large energy barrier for deionization impede their rechargeability. Here, the reversibility of potassium halides, lithium halides, sodium halides, and zinc halides is achieved through decreasing their dimensionality by the strong π-cation interactions between metal cations and reduced graphene oxide (rGO). Especially, the energy densities of KI-, KBr-, and KCl-based materials are 722.2, 635.0, and 739.4 Wh kg-1 , respectively, which are higher than those of other cathode materials for potassium-ion batteries. In addition, the full-cell with 2D KI/rGO as cathode and graphite as anode demonstrates a lifespan of over 150 cycles with a considerable capacity retention of 57.5%. The metal halides-based electrode materials possess promising application prospects and are worthy of more in-depth researches.

Coaxial Graphene/MXene Microfibers with Interfacial Buffer-Based Lightweight Distance Sensors Assisting Lossless Grasping of Fragile and Deformable Objects.

Lossless and efficient robotic grasping is becoming increasingly important with the widespread application of intelligent robotics in warehouse transportation, human healthcare, and domestic services. However, current sensors for feedback of grasping behavior are greatly restricted by high manufacturing cost, large volume and mass, complex circuit, and signal crosstalk. To solve these problems, here, we prepare lightweight distance sensor-based reduced graphene oxide (rGO)/MXene-rGO coaxial microfibers with interface buffer to assist lossless grasping of a robotic manipulator. The as-fabricated distance microsensor exhibits a high sensitivity of 91.2 m-1 in the distance range of 50-300 µm, a fast response time of 116 ms, a high resolution of 5 µm, and good stability in 500 cycles. Furthermore, the high-performance and lightweight microsensor is installed on the robotic manipulator to reflect the grasp state by the displacement imposed on the sensor. By establishing the correlation between the microsensing signal and the grasp state, the safe, non-destructive, and effective grasp and release of the target can be achieved. The lightweight and high-powered distance sensor displays great application prospects in intelligent fetching, medical surgery, multi-spindle automatic machines, and cultural relics excavation.

Detection of Various Microplastics in Patients Undergoing Cardiac Surgery.

Microplastics have been detected in human stool, lungs, and placentas, which have direct exposure to the external environment through various body cavities, including the oral/anal cavity and uterine/vaginal cavity. Crucial data on microplastic exposure in completely enclosed human organs are still lacking. Herein, we used a laser direct infrared chemical imaging system and scanning electron microscopy to investigate whether microplastics exist in the human heart and its surrounding tissues. Microplastic specimens were collected from 15 cardiac surgery patients, including 6 pericardia, 6 epicardial adipose tissues, 11 pericardial adipose tissues, 3 myocardia, 5 left atrial appendages, and 7 pairs of pre- and postoperative venous blood samples. Microplastics were not universally present in all tissue samples, but nine types were found across five types of tissue with the largest measuring 469 µm in diameter. Nine types of microplastics were also detected in pre- and postoperative blood samples with a maximum diameter of 184 µm, and the type and diameter distribution of microplastics in the blood showed alterations following the surgical procedure. Moreover, the presence of poly(methyl methacrylate) in the left atrial appendage, epicardial adipose tissue, and pericardial adipose tissue cannot be attributed to accidental exposure during surgery, providing direct evidence of microplastics in patients undergoing cardiac surgery. Further research is needed to examine the impact of surgery on microplastic introduction and the potential effects of microplastics in internal organs on human health.

Anion Concentration Gradient-Assisted Construction of a Solid-Electrolyte Interphase for a Stable Zinc Metal Anode at High Rates.

Coulombic efficiency (CE) and cycle life of metal anodes (lithium, sodium, zinc) are limited by dendritic growth and side reactions in rechargeable metal batteries. Here, we proposed a concept for constructing an anion concentration gradient (ACG)-assisted solid-electrolyte interphase (SEI) for ultrahigh ionic conductivity on metal anodes, in which the SEI layer is fabricated through an in situ chemical reaction of the sulfonic acid polymer and zinc (Zn) metal. Owing to the driving force of the sulfonate concentration gradient and high bulky sulfonate concentration, a promoted Zn2+ ionic conductivity and inhibited anion diffusion in the SEI layer are realized, resulting in a significant suppression of dendrite growth and side reaction. The presence of ACG-SEI on the Zn metal enables stable Zn plating/stripping over 2000 h at a high current density of 20 mA cm-2 and a capacity of 5 mAh cm-2 in Zn/Zn symmetric cells, and moreover an improved cycling stability is also observed in Zn/MnO2 full cells and Zn/AC supercapacitors. The SEI layer containing anion concentration gradients for stable cycling of a metal anode sheds a new light on the fundamental understanding of cation plating/stripping on metal electrodes and technical advances of rechargeable metal batteries with remarkable performance under practical conditions.

Integrated Polypyrrole-Based Smart Clothing with Photothermal Conversion and Thermosensing Functions for Wearable Applications.

Integrated smart clothing with photothermal conversion and thermosensing functions is highly desired for next-generation smart wearable applications. Conducting polymer is a promising material that possesses efficient photothermal conversion performance, great sensitivity to temperature change, and excellent processing properties. In this study, we report a new wearable material using the conducting polymer polypyrrole (PPy) as a photothermal and thermosensing layer and nonwoven fabric as flexible textiles to fabricate integrated PPy-based smart clothing (IPSC). The surface temperature of the prepared IPSC can be as high as 68.4 °C with 808 nm near-infrared (NIR) irradiation at a power destiny of 1 kW/m2. Meanwhile, a temperature resolution of 1 °C can be achieved for IPSC. These superiorities are in favor of fabricating multifunctional smart wearables to satisfy the needs in future life.

Highly Selective Wearable Smartsensors for Vapor/Liquid Amphibious Methanol Monitoring.

A wearable screen-printed electrochemical smartsensor with excellent selectivity for methanol quantification has been developed. This smartsensor consists of a printable sensing system modified with platinum (Pt) confined in a reduced graphene oxide (rGO) matrix, as well as a compact electronic interface for data collection. The real-time electrochemical signal from methanol could be remotely detected and transmitted to a smartphone by blue tooth. It performs good environmental adaptability of vapor/liquid amphibious behaviors. Owing to the uniform distribution of Pt loading on the rGO nanosheets, this sensor demonstrates high selectivity, sensitivity, stability, and recoverability both in vapor and liquid during temperature or humidity diversification, compared with other resistance-based sensors. It also achieves good bending and stretching performance, and it could be a possible candidate device for the quantification of methanol in different environments.

Engineering Fast Ion Conduction and Selective Cation Channels for a High-Rate and High-Voltage Hybrid Aqueous Battery.

The rechargeable aqueous metal-ion battery (RAMB) has attracted considerable attention due to its safety, low costs, and environmental friendliness. Yet the poor-performance electrode materials lead to a low feasibility of practical application. A hybrid aqueous battery (HAB) built from electrode materials with selective cation channels could increase the electrode applicability and thus enlarge the application of RAMB. Herein, we construct a high-voltage K-Na HAB based on K2 FeFe(CN)6 cathode and carbon-coated NaTi2 (PO4 )3 (NTP/C) anode. Due to the unique cation selectivity of both materials and ultrafast ion conduction of NTP/C, the hybrid battery delivers a high capacity of 160 mAh g-1 at a 0.5 C rate. Considerable capacity retention of 94.3 % is also obtained after 1000 cycles at even 60 C rate. Meanwhile, high energy density of 69.6 Wh kg-1 based on the total mass of active electrode materials is obtained, which is comparable and even superior to that of the lead acid, Ni/Cd, and Ni/MH batteries.

Size-tunable, highly sensitive microelectrode arrays enabled by polymer pen lithography.

By combining polymer pen lithography (PPL) patterning with in situ polymerization, we report a straightforward and bottom-up approach for bench-top fabrication of microelectrode arrays (MEAs) with well-controlled dimensions. The as-fabricated MEAs can be used to electrodeposit prussian blue in situ and work as a biosensor for H2O2 with a detection limit as low as 5 nM at a sensitivity of 0.7 A cm-2 M-1.

Unlocking the Electrocatalytic Activity of Antimony for CO2 Reduction by Two-Dimensional Engineering of the Bulk Material.

Two-dimensional (2D) materials are known to be useful in catalysis. Engineering 3D bulk materials into the 2D form can enhance the exposure of the active edge sites, which are believed to be the origin of the high catalytic activity. Reported herein is the production of 2D "few-layer" antimony (Sb) nanosheets by cathodic exfoliation. Application of this 2D engineering method turns Sb, an inactive material for CO2 reduction in its bulk form, into an active 2D electrocatalyst for reduction of CO2 to formate with high efficiency. The high activity is attributed to the exposure of a large number of catalytically active edge sites. Moreover, this cathodic exfoliation process can be coupled with the anodic exfoliation of graphite in a single-compartment cell for in situ production of a few-layer Sb nanosheets and graphene composite. The observed increased activity of this composite is attributed to the strong electronic interaction between graphene and Sb.

Colloidal pen lithography.

Colloidal pen lithography, a low-cost, high-throughput scanning probe contact printing method, has been developed, which is based on self-assembled colloidal arrays embedded in a soft elastomeric stamp. Patterned protein arrays are demonstrated using this method, with a feature size ranging from 100 nm to several micrometers. A brief study into the specificity reorganization of protein gives evidence for the feasibility of this method for writing protein chips.

In situ characterisation for nanoscale structure-performance studies in electrocatalysis.

Recently, electrocatalytic reactions involving oxygen, nitrogen, water, and carbon dioxide have been developed to substitute conventional chemical processes, with the aim of producing clean energy, fuels and chemicals. A deepened understanding of catalyst structures, active sites and reaction mechanisms plays a critical role in improving the performance of these reactions. To this end, in situ/operando characterisations can be used to visualise the dynamic evolution of nanoscale materials and reaction intermediates under electrolysis conditions, thus enhancing our understanding of heterogeneous electrocatalytic reactions. In this review, we summarise the state-of-the-art in situ characterisation techniques used in electrocatalysis. We categorise them into three sections based on different working principles: microscopy, spectroscopy, and other characterisation techniques. The capacities and limits of the in situ characterisation techniques are discussed in each section to highlight the present-day horizons and guide further advances in the field, primarily aiming at the users of these techniques. Finally, we look at challenges and possible strategies for further development of in situ techniques.

Superconductivity in potassium-doped few-layer graphene.

Here we report the successful synthesis of superconducting potassium-doped few-layer graphene (K-doped FLG) with a transition temperature of 4.5 K, which is 1 order of magnitude higher than that observed in the bulk potassium graphite intercalation compound (GIC) KC(8) (T(c) = 0.39 K). The realization of superconductivity in K-doped FLG shows the potential for the development of new superconducting electronic devices using two-dimensional (2D) graphene as a basis material.

A Novel Ionic Conductive Polyurethane Based on Deep Eutectic Solvent Continuing Traditional Merits.

Artificial intelligence (AI) has become increasingly popular along with the development of the bionic neural system. Ionic conductors play an important role in the AI system due to the ability of bionic sensing and signal transporting. Traditional low-polarity elastomers possess outstanding mechanical strength and stability, such as polyurethane, which is difficult to be directly endowed with ionic conductivity without impairing its properties. Herein, we have first put forward a new approach to synthesize a liquid-free ionic conductive polyurethane (CPU) through one-step copolymerization between a green deep eutectic solvent (DES) and a prepolymer of polyurethane. The as-prepared CPU can retain the native properties of the traditional polyurethane (PU) such as the homogeneous phase, ease of molding, high transparency (about 93.3%), and excellent mechanical properties. By introducing the DES as the covalent cross-linking agent and ionic conductor at the same time, the CPU also has fine ionic conductivity (3.78 × 10-5 S cm-1), environmental resistance like anti-freezing (-20 °C), and solvent resistance. Based on the excellent conductivity and mechanical strength, the flexible CPU can be applied as a sensing element in pressure sensors. The CPU-based sensor has presented long-term stability, high sensitivity, and wide-ranging response (0.17-3.28 MPa) to the applied pressure, which will be suitable for the industrial demands for practical applications.

Facile patterning of reduced graphene oxide film into microelectrode array for highly sensitive sensing.

In this study, we develop a new technique to fabricate a reduced graphene oxide (rGO)-based microelectrode array (MEA) with low-cost soft lithography. To prepare patterned rGO, a polydimethylsiloxane (PDMS) mold with an array of microwells on its surface is fabricated using soft lithography, and GO is assembled on an indium tin oxide (ITO) electrode with a layer-by-layer method. The rGO pattern is formed by closely contacting the assembled GO film onto the ITO electrode with the PDMS mold filled with hydrazine solution in the microwells to selectively reduce the localized GO into the rGO. The MEA with patterned rGO as the microelectrode is characterized with Kelvin probe force microscopy (KFM), atomic force microscopy (AFM), and cyclic voltammetry (CV) with ferricyanide in aqueous solution as the redox probe. The KFM and AFM results demonstrate that each rGO pattern prepared under the present conditions is 3 µm in diameter, which is close to that of the PDMS mold we use. The CV results show that the rGO patterned onto the ITO exhibits a sigmoid-shaped voltammogram up to 200 mVs(-1) with a microampere level current response, suggesting that the rGO-based electrode fabricated with soft lithography behalves like a MEA. To demonstrate the potential electroanalytical application of the rGO-based MEA, prussian blue (PB) is electrodeposited onto the rGO-based MEA to form the PB/rGO-based MEA. Electrochemical studies on the formed PB/rGO-based MEA reveal that MEA shows a lower detection limit and a larger current density for the detection of H(2)O(2), as compared with the macroscopic rGO electrode. The method demonstrated here provides a simple and low-cost strategy for the fabrication of graphene-based MEA that are useful for electroanalytical applications.

Facile fabrication of metallic nanostructures by tunable cracking and transfer printing.

You crack me up: A topographically patterned PDMS stamp was coated with thin metal film and swelled under organic vapor to induce the tunable cracking of the brittle film into metallic nanostructures (see SEM images, scale bars 1 µm). UV/Vis spectra, OLED efficiency, and SERS spectra demonstrate the fine controllability of the metallic nanostructures, the well-ordered and highly regulable surface plasmons, and the facile fabrication process.

In Situ Construction of a Multifunctional Quasi-Gel Layer for Long-Life Aqueous Zinc Metal Anodes.

Aqueous zinc (Zn)-ion batteries are considered very promising in grid-scale energy storage systems. However, the dendrite, corrosion, and H2 evolution issues of Zn anode have restricted their further applications. Herein, to solve these issues, a hydrophilic layer, consisting of a covalent organic polymer (COP) and carboxylmethyl cellulose (CMC), is designed to in situ construct a multifunctional quasi-gel (COP-CMC/QG) interface between Zn metal and the electrolyte. The COP-CMC/QG interface can significantly improve the rechargeability of the Zn anode through enhancing Zn2+ transport kinetics, guiding uniform nucleation, and suppressing Zn corrosion and H2 evolution. As a result, the COP-CMC-Zn anode exhibits a reduced overpotential (12 mV at 0.25 mA cm-2), prolonged cycle life (over 4000 h at 0.25 mA cm-2 and 2000 h at 5 mA cm-2 in symmetrical cells), and elevated full-cell (Zn/MnO2) performance. This work provides an efficient approach to achieve long-life Zn metal anodes and paves the way toward high-performance Zn-based and other metal-ion batteries.

Reduced Graphene Oxide-Polypyrrole Aerogel-Based Coaxial Heterogeneous Microfiber Enables Ultrasensitive Pressure Monitoring of Living Organisms.

Pressure sensors for living organisms can monitor both the movement behavior of the organism and pressure changes of the organ, and they have vast perspectives for the health management information platform and disease diagnostics/treatment through the micropressure changes of organs. Although pressure sensors have been widely integrated with e-skin or other wearable systems for health monitoring, they have not been approved for comprehensive surveillance and monitoring of living organisms due to their unsatisfied sensing performance. To solve the problem, here, we introduce a novel structural design strategy to manufacture reduced graphene oxide-polypyrrole aerogel-based microfibers with a typical coaxial heterogeneous structure, which significantly enhances the sensitivity, resolution, and stability of the derived pressure microsensors. The as-fabricated pressure microsensors exhibit ultrahigh sensitivities of 12.84, 18.27, and 4.46 kPa-1 in the pressure ranges of 0-20, 20-40, and 40-65 Pa, respectively, high resolution (0.2 Pa), and good stability in 450 cycles. Furthermore, the microsensor is applied to detect the movement behavior and organic micropressure changes for mice and serves as a platform for monitoring micropressure for the integrative diagnosis both in vivo and in vitro of organisms.

A hybrid superconcentrated electrolyte enables 2.5 V carbon-based supercapacitors.

A hybrid solvent in salt electrolyte was developed by hybridizing aqueous and organic solvents in concentrated lithium bis(fluorosulfonyl)imide (LiFSI) salts, such an electrolyte provides an unprecedented electrochemical window of 5.35 V, which is even comparable to traditional organic electrolytes, and enables a super-stable carbon-based symmetric supercapacitor with a long life of 10 000 cycles at an operating voltage of 2.5 V.