A novel online analyzer for accurate and rapid measurement of volatile fatty acids in anaerobic wastewater treatment.

Volatile fatty acids (VFAs), which are largely generated during the anaerobic acidification process, are considered to be reliable indicators of the stable process operation. However, the common methods for monitoring VFAs are offline, and they are typically manual requiring time-consuming, costly and complex instruments. This study aims to develop a novel online analyzer for automatic measuring VFAs, which was based on the 5-pH point titration, embedded with a proportional-integral-derivative (PID) feedback control system. The results show that it can achieve accurate and rapid monitoring of VFAs ranging between 0-400 mg/L (<9 min/sample) but simultaneously faces the problems of overtitration and interference of complex characteristics of wastewater. In order to improve its accuracy and stability, the effects of three general coefficients (KI,KP, and KD) of PID on the titration were investigated, and the optimal values of KI, KP, and KD were found to be 1.5, 1.0, and -1.0~0.5, respectively. Besides, the initial titration speed was set at 0.06 mL/min, equal to the minimum speed of the peristaltic pump, and the dichotomy approach was integrated into the PID feedback controller. Owing to the above improvements, the relative mean deviation and standard deviation of measuring VFAs in both synthetic and real wastewaters were mostly lower than 5.0% and 5.0 mg/L, proving the online analyzer is rapid, accurate and reliable.

Biofilm development in a pilot-scale gravity sewer: Physical characteristics, microstructure, and microbial communities.

The existence of abundant biofilms on sewer pipeline walls can lead to negative environmental impacts, such as poisonous gas release and pipe corrosions through transforming various pollutants. Investigating the formation process of sewer biofilms is of importance in advancing knowledge of sewer operation and maintenance. In this study, the changes in physical characteristics, microstructure, and microbial communities of sewer biofilm were analyzed in-depth in a pilot-scale gravity sewer during a 45-day operation. The results show that a high specific surface area at the early stage could channel the substrates for stimulating the primary colonizers (e.g., Cytophagia, Sphingobacteriia, Alpha-, and Betaproteobacteria), which could excrete an extracellular matrix to facilitate biofilm growth. The sewer biofilms were gradually formed with 62 g VS/m2 organic content, 1.2 mm biofilm thickness, and 89 mg/cm3 dry density after 45 days operation. Moreover, the biofilm growth promoted the emergence of facultative bacteria and anaerobes (affiliated with Flavobacteriia, Gemmatimonadetes, Deltaproteobacteria, and Epsilonproteobacteria). Microelectrode analysis further verified that an anaerobic zone existed in mature biofilm with a negative oxidation-reduction potential (-105 mV), where approximately 0.1 µmol/L of sulfide was produced. Our results suggest that the migration of the microbial community correlated with the changes in the evolved physical characteristics and microstructure of sewer biofilm, and this can contribute to the strategies for sulfide control for improving sewer maintenance.

Test of transformation mechanism of food waste and its impacts on sulfide and methane production in the sewer system.

Food waste (FW) management has become an important issue worldwide. Diverting FW into the sewer system is considered promising to tackle the FW issue. However, the transformation of FW in sewers and its impact on the sewer process have not received adequate attention due to the overlooked sewer networks. In this study, a laboratory-scale sewer reactor system was established to investigate the transformation of FW and the production of sulfide and methane under anaerobic conditions. The transformation of FW in the sewer reactor could result in an increase in the substrate level through hydrolyzing and converting biodegradable substances into preferred substrates. Moreover, the generated substrates from the addition of FW were preferable for the metabolism of key microbes in sewer biofilms. As a result, methane production from the sewer reactor could be enhanced from the addition of FW, whereas sulfide production was not affected at a low sulfate concentration. The findings of this study suggest that the diversion of FW may exert an adverse impact on sewers and the environment in terms of greenhouse gas emission. Hence, more research is necessary to clarify the detailed impacts on FW management and wastewater treatment.

A novel approach to quantifying elemental sulfur (S0) in environmental samples.

The quantification of elemental sulfur (S0) is an important part of monitoring and controlling sulfur-involving processes. Existing methods of S0 detection either require significant time or involve the use of toxic chemicals. We have developed and validated a new method to determine S0 in environmental samples using calorimeter-ion chromatography (IC), in which S0 is fully oxidized to sulfur trioxide (SO3) with pure oxygen at 20 atm in a calorimeter. The resulting SO3 is then absorbed by a sodium bicarbonate (NaHCO3) solution and analyzed using IC. To verify this method, standard samples with various sulfur contents (5-200 mg S), possible interfering substances (SO42-, SO32-, S2O32- and S2-), and mixed environmental samples were tested and compared. The high correlation of R2 = 0.999 between the examined and theoretical values was obtained with a high recovery rate of ≥95% and a low relative standard deviation (RSD) of ≤1%. Samples containing at least 25 mg of S0 were accurately measured (recovery error < 5%). Thiosulfate was identified as the main interfering substance, and pretreatment was needed to eliminate it. This new method is more efficient, cost-effective, easier to operate, and more secure and accurate than existing methods.

Sulfur bacteria-reinforced microbial electrochemical denitrification.

Two limiting factors of microbial electrochemical denitrification (MED) are the abundance and efficiency of the functional microorganisms. To supply these microorganisms, MED systems are inoculated with denitrifying sludge, but such method has much room for improvement. This study compared MED inoculated with autotrophic denitrifying inoculum (ADI) versus with heterotrophic denitrifying inoculum (HDI). ADI exhibited electroactivity for 50% less of timethan HDI. The denitrification efficiency of the ADI biocathode was42% higherthan that of the HDI biocathode. The HDI biocathode had high levels of polysaccharides while the ADI biocathode was rich in proteins, suggesting that two biocathodes may achieveMED but via differentpathways. Microbial communities of two biocathodes indicated MED of HDI biocathode may rely on interspecies electron transfer, whereas sulfur bacteria of ADI biocathode take electrons directly from the cathode to achieve MED. Utilizing autotrophic sulfur-oxidizing denitrifiers, this study offers a strategy for enhancing MED.

Comparative life cycle assessment of sewage sludge treatment in Wuhan, China: Sustainability evaluation and potential implications.

Owing to the relentless growth of sewage sludge production, achieving low-carbon development in sewage sludge treatment and disposal (STD) is becoming increasingly challenging and unpredictable. However, the STD varied spatially, and city-specific analysis is deemed necessary for sustainable evaluation. Therefore, a lifecycle-based greenhouse gas (GHG), energy, and economic analysis were conducted by considering six local STD alternatives in Wuhan City, China, as a case study. The findings indicated anaerobic digestion combined with digestate utilization for urban greening (ADL) and incineration in existing power plants (INCP) exhibited the least GHG emissions at 34.073 kg CO2 eq/FU and 644.128 kg CO2 eq/FU, while INCP generated the most energy at -2594 kW.h/FU. The economic evaluation revealed that ADL and INCP were more beneficial without accounting for land acquisition. Scenario analysis showed that the energy recovery from ADL and INCP is significantly influenced by the hydrolysis yielding rate and sludge organic content. Perturbation sensitivity indicates that regional emission factor of electricity and electricity fee highly influence the overall GHG emission and cost. The results of this study could assist policymakers in identifying viable solutions to the cities experiencing the same sludge treatment burdens.

Electrogenerated singlet oxygen and reactive chlorine species enhancing volatile fatty acids production from co-fermentation of waste activated sludge and food waste: The key role of metal oxide coated electrodes.

Electrochemical pretreatment (EPT) has shown to be superior in improving acidogenic co-fermentation (Co-AF) of waste activated sludge (WAS) and food waste (FW) for volatile fatty acids (VFAs). However, the influence of EPT electrode materials on the production of electrogenerated oxidants (such as singlet oxygen (1O2) and reactive chlorine species (RCS)), as well as their effects on properties of electrodes, the microbial community structure and functional enzymes remain unclear. Therefore, this study investigated the effects of various metal oxide coated electrodes (i.e., Ti/PbO2, Ti/Ta2O5-IrO2, Ti/SnO2-RuO2, and Ti/IrO2-RuO2) on EPT and subsequent Co-AF of WAS-FW. The results showed that EPT with Ti/PbO2, Ti/Ta2O5-IrO2, Ti/SnO2-RuO2 and Ti/IrO2-RuO2 electrodes generated 165.3-848.2 mg Cl2/L of RCS and 5.643 × 1011-3.311 × 1012 spins/mm3 of 1O2, which significantly enhanced the solubilization and biodegradability of WAS-FW by 106.4 %-233.6 % and 177.3 %-481.8 %, respectively. Especially with Ti/Ta2O5-IrO2 as the electrode material, an appropriate residual RCS (2.0-10.4 mg Cl2/L) remained in Co-AF step, resulted in hydrolytic and acidogenic bacteria (e.g., Prevotella_7, accounting for 78.9 %) gradually become dominant rather than methanogens (e.g., Methanolinea and Methanothrix) due to their different tolerance to residual RCS. Meanwhile, the functional gene abundances of hydrolytic and acidogenic enzymes increased, while the methanogenic enzymes deceased. Consequently, this reactor produced the highest VFAs up to 545.5 ± 36.0 mg COD/g VS, which was 101.8 % higher than that of the Control (without EPT). Finally, the economic analysis and confirmatory experiments further proved the benefits of WAS-FW Co-AF with EPT.

Thiosulfate/FeCl3 pre-treatment enhances short-chain fatty acid production and mitigates H2S generation during anaerobic fermentation of waste activated sludge: Performance, microbial community and ecological analyses.

Anaerobic fermentation (AF) has been identified as a promising method of transforming waste activated sludge (WAS) into high-value products (e.g., short-chain fatty acids (SCFAs)). This study developed thiosulfate/FeCl3 pre-treatment and investigated the effects of different thiosulfate/FeCl3 ratios (S:Fe = 3:1, 3:2, 1:1, 3:4 and 3:5) on SCFA production and sulfur transformation during the AF of WAS. At a S:Fe ratio of 1:1, the maximal SCFA yield (933.3 mg COD/L) and efficient H2S removal (96.5 %) were obtained. S:Fe ratios ≤ 1:1 not only benefited hydrolysis and acidification but largely mitigated H2S generation. These results were supported by the enriched acidogens and reduced sulfur-reducing bacteria (SRB). Molecular ecological network analysis further revealed that the keystone taxon (g_Saccharimonadales) was found in S:Fe = 1:1, together with reductions in associations among methanogens, acidogens and SRB. This work provides a strategy for enhancing high-value product recovery from WAS and minimising H2S emissions.

Roles of the SOM and clay minerals in alleviating the leaching of Pb, Zn, and Cd from the Pb/Zn smelter soil: Multi-surface model and DFT study.

Soil organic matter (SOM) and clay minerals are important sinks for reactive heavy metals (HMs) and exogenous hydrogen ions (H+). Therefore, HMs are likely to be released into soil porewater under acid rainfall conditions due to the competitive adsorption of H+. However, negligible Lead, Zinc, and Cadmium (<6 ‰) in the Pb/Zn smelter soil were leached, and the effects of SOM and clay minerals on HMs leaching were unclear. Herein, the H+ consumption and HMs redistribution on SOM and clay minerals were quantitated by the multi-surface model and density functional theory calculations to reveal the roles of SOM and clay minerals in alleviating HMs' leaching. Clay minerals consumed 43.2 %-52.0 % of the exogenous H+, serving as the dominant sink for the exogenous H+ due to its high content and hindering H+ competitive adsorption on SOM. Protonation of the functional groups constituted >90 % of the total H+ captured by clay minerals. Meanwhile, some H+ also competed with HMs for adsorption sites on clay minerals due to its 0.497-fold to 1.54-fold higher binding energies than HMs, resulting in the release of HMs. On the contrary, SOM served as an accommodator for taking over the released HMs from clay minerals. The HMs complexation on the low-affinity sites (R-L-) of SOM was responsible for the recapture of HMs. In Ca-enriched soil, the released HMs were also recaptured by SOM via ion exchange on the R-L-Ca+ and the high-affinity sites (R-H-Ca+) sites due to the 30.8 %-178 % higher binding energies of HMs on these sites than those of Ca. As a result, >63.4 % of the released HMs from clay minerals were transferred to the SOM. Thus, the synergy of SOM and clay minerals in alleviating the leaching of HMs in Pb/Zn smelter soils cannot be ignored in risk assessment and soil remediation.

In-situ sulfite treatment promotes solid reduction during aerobic digestion of waste activated sludge: Feasibility for small-scale wastewater treatment plants.

Aerobic digestion remains the preferred choice for small-scale wastewater treatment plants (WWTPs) in some developing countries, largely due to economic viability and operational simplicity. The escalating production of waste activated sludge (WAS) has prompted small-scale WWTPs to improve efficiency. To address this issue, this study employed an in-situ sulfite treatment as a non-intrusive method to augment aerobic digestion. With sulfite-enhanced solubilization and hydrolysis, a 3.6-fold increase in degradation was achieved. Both sludge dewatering properties and pathogens inactivation were improved. Microbial community analysis revealed a preferential enrichment of Actinobacteriota and Firmicutes during sulfite treatment. The desktop scaling-up estimation suggests that implementing this treatment yielded operational cost savings exceeding 40 %. In summary, in-situ sulfite treatment offers a cost-effective strategy for WAS management in small-scale WWTPs.

Net zero greenhouse emissions and energy recovery from food waste: manifestation from modelling a city-wide food waste management plan.

Food waste (FW) being a major solid waste component and of degradable nature is the most challenging to manage and mitigate greenhouse gas emissions (GHEs). Policymakers seek innovative approaches to achieve net zero objectives and recover resources from the FW which requires a comparative and holistic investigation of contemporary treatment methods. This study assessed the lifecycle of six alternative scenarios for reducing net GHEs and energy use potential from FW management in a metropolis, taking Hong Kong as a reference. In both impact categories, the business-as-usual (landfilling) was the worst-case scenario. The combined anaerobic digestion and composting (ADC) technique was ranked best in the global warming impact but was more energy intensive than anaerobic digestion with sludge landfilling (ADL). Incineration ranked second in net GHEs but less favourable for energy recovery from FW alone. The proposed integration of FW and biological wastewater treatment represented an enticing alternative. Integration by co-disposal and treatment with wastewater (CoDT-WW) performed above average in both categories, while anaerobic co-digestion with sewage sludge (AnCoD-SS) ranked fourth. The sensitivity analysis further identified critical parameters inherent to individual scenarios along with biogenic carbon emission and sequestration, revealing their significance on the magnitude of GHEs and scenarios' ranking. Capacity assessment of the studied treatment facilities showed a FW diversion potential of ∼60% while reducing the net GHEs by ∼70% compared to the base-case, indicating potential of net zero carbon emissions and energy footprint by increasing treatment capacity. From this study, policymakers can gain insights and guidelines for low-carbon urban infrastructure development worldwide.

In situ coagulation-electrochemical oxidation of leachate concentrate: A key role of cathodes.

To efficiently remove organic and inorganic pollutants from leachate concentrate, an in situ coagulation-electrochemical oxidation (CO-EO) system was proposed using Ti/Ti4O7 anode and Al cathode, coupling the "super-Faradaic" dissolution of Al. The system was evaluated in terms of the removal efficiencies of organics, nutrients, and metals, and the underlying cathodic mechanisms were investigated compared with the Ti/RuO2-IrO2 and graphite cathode systems. After a 3-h treatment, the Al-cathode system removed 89.0% of COD and 36.3% of total nitrogen (TN). The TN removal was primarily ascribed to the oxidation of both ammonia and organic-N to N2. In comparison, the Al-cathode system achieved 3-10-fold total phosphorus (TP) (62.6%) and metal removals (>80%) than Ti/RuO2-IrO2 and graphite systems. The increased removals of TP and metals were ascribed to the in situ coagulation of Al(OH)3, hydroxide precipitation, and electrodeposition. With the reduced scaling on the Al cathode surface, the formation of Al3+ and electrified Al(OH)3 lessened the requirement for cathode cleaning and increased the bulk conductivity, resulting in increased instantaneous current production (38.9%) and operating cost efficiencies (48.3 kWh kgCOD -1). The present study indicated that the in situ CO-EO process could be potentially used for treating persistent wastewater containing high levels of organic and inorganic ions.

Achieving efficient methane production from protein-rich organic waste in anaerobic digestion: Using conductive materials or regulating inoculum-to-substrate ratios?

The contribution of inoculum-to-substrate ratios (ISRs) and conductive materials (CMs) on the productivity of anaerobic digestion (AD) remains unclear, particularly for protein-rich organic waste. This study investigated whether the addition of CMs, i.e., biochar and iron powder, can overcome the limitations imposed by varying ISRs for the AD of protein as the sole substrate. Results indicate the ISR plays a decisive role in hydrolysis, acidification, and methanogenesis for protein conversion, irrespective of CMs addition. Methane production increased stepwise as the ISR escalated to 3:1. The addition of CMs provided limited improvement, and iron powder even inhibited methanogenesis at a low ISR. Bacterial community variations were contingent on the ISR, while iron powder supplementation significantly elevates the proportion of hydrogenotrophic methanogen. This study demonstrates that the addition of CMs could affect methanogenic efficiency but can not overcome the limitation of ISRs for the AD of protein.

Optimizing waste activated sludge disintegration by investigating multiple electrochemical pretreatment conditions: Performance, mechanism and modeling.

The complex and rigid floc structure often limits the reutilization of waste activated sludge (WAS). Electrochemical pretreatment (EPT) is one of the most effective technologies that can enhance WAS disintegration. But a comprehensive investigation into how multiple EPT conditions work was rarely reported. The study evaluated the effects of multiple EPT conditions, i.e., different electrolytes (NaCl, Na2SO4, and CaCl2), electrolytes dosage (0 g/L, 0.5 g/L, 1.0 g/L, and 3.0 g/L), EPT current (0 A, 0.5 A, 1.0 A, and 3.0 A) and EPT time (0 min, 30 min, 60 min, and 90 min) on WAS disintegration. The results showed that NaCl was outstanding from other electrolytes in promoting more WAS disintegration. Besides, a relatively higher NaCl dosage, a higher EPT current, and a longer EPT time promoted more reactive chlorine species (RCS), thus enhancing WAS disintegration in terms of extracellular polymeric substances (EPS) structure destruction and biodegradable organic matter release. After EPT for 60 min at NaCl dosage of 1.0 g/L and current of 1.0 A, the EPS multilayer structure destruction, biodegradable organic matters release, and soluble chemical oxygen demand (SCOD) increase in the supernatant were enhanced by 17.2 %, 130.5 %, and 238.7 %, respectively. Then a predictive quadratic model was established and the impact significance of the above EPT factors for enhancing WAS disintegration followed dosage of NaCl > current > EPT time. Furthermore, response surface methodology (RSM) suggested NaCl dosage of 2.75 g/L, current of 2.0 A, and EPT time of 30 min were the optimal EPT conditions, bringing a 42.0 % increase in the net economic benefit of WAS treatment compared to without EPT.

Short-chain fatty acid production and phosphorous recovery from waste activated sludge via anaerobic fermentation: A comparison of in-situ and ex-situ thiosulfate-assisted Fe2+/persulfate pretreatment.

Recently, increasing attention is given on the resource and energy recovery (e.g. short-chain fatty acids (SCFAs) and phosphorus (P)) from waste active sludge (WAS) under the "Dual carbon goals". This study compared four thiosulfate-assisted Fe2+/persulfate (TAFP) pretreatments of WAS, i.e. in-situ TAFP pretreatment (R1), ex-situ TAFP pretreatment (R2), in-situ TAFP pretreatment + pH adjustment (R3) and ex-situ TAFP pretreatment + pH adjustment (R4), followed by anaerobic fermentation over 20 days for SCFA production and P recovery. The results showed that the maximal SCFA yields in R1-4 were 730.2 ± 7.0, 1017.4 ± 13.9, 860.1 ± 40.8, and 1072.0 ± 33.2 mg COD/L, respectively, significantly higher than Control (365.2 ± 17.8 mg COD/L). The findings indicated that TAFP pretreatments (particularly ex-situ TAFP pretreatment) enhanced WAS disintegration and provided more soluble organics and subsequently promoted SCFA production. The P fractionation results showed the non-apatite inorganic P increased from 11.6 ± 0.2 mg P/g TSS in Control to 11.8 ± 0.5 (R1), 12.4 ± 0.3 (R2), 13.2 ± 0.7 (R3) and 12.7 ± 0.7 mg P/g TSS (R4), suggesting TAFP pretreatments improved P bioavailability due to formation of Fe-P mineral (Fe(H2PO4)2·2H2O), which could be recycled through magnetic separators. These findings were further strengthened by the analysis of microbial community and related marker genes that fermentative bacteria containing SCFA biosynthesis genes (e.g. pyk, pdhA, accA and accB) and iron-reducing bacteria containing iron-related proteins (e.g. feoA and feoB) were enriched in R1-4 (dominant in ex-situ pretreatment systems, R2 and R4). Economic evaluation further verified ex-situ TAFP pretreatment was cost-effective and a better strategy over other operations to treat WAS for SCFA production and P recovery.

Achieving superior nitrogen removal in an air-lifting internal circulating reactor for municipal wastewater treatment: Performance, kinetic analysis, and microbial pathways.

Anticipated growth in living standards has accentuated higher requirements for effluent quality from municipal wastewater treatment. In this study, an air-lifting internal circulating reactor with a high internal circulation ratio (36:1) was established to treat municipal wastewater with a long-term operation. In the bioreactor, the average effluent chemical oxygen demand, total nitrogen, and ammonium nitrogen could be 13.1, 5.7, and lower than 1 mg/L, respectively. Further analysis of nitrogen removal showed that traditional nitrification and denitrification, simultaneous nitrification and denitrification (SND), and nitrogen assimilation accounted for 27.4 %, 68.7 %, and 3.9 % respectively. The proportion of aerobic bacteria (Saprospiraceae) and facultative bacteria (Comamonadaceae) were significantly increased, indicating a higher capacity for organic degradation in the reactor. The relative abundance of denitrifying bacteria and bacterial groups with SND (Comamonadaceae) increased. These results suggested the air-lifting internal circulating reactor could be a viable and efficient option for superior nitrogen removal in wastewater treatment.

In-situ sulfite treatment enhanced the production of short-chain fatty acids from waste activated sludge in the side-stream anaerobic fermentation.

Sulfite-based technology could enhance methane production from anaerobic sludge digestion. However, its potential for in-situ direct sludge treatment without anaerobic sludge addition in the side-stream remains unclear. This study investigated the feasibility of using in-situ sulfite treating sludge for short-chain fatty acids (SCFAs) production via anaerobic fermentation of waste activated sludge (WAS) as a side-stream treatment. In-situ sulfite direct sludge treatment enhanced SCFAs and acetic acid production by 2.03 and 4.89 times at 500 mg S/L compared to the control. With in-situ sulfite treatment, WAS hydrolysis and acidification were enhanced while methanogenesis was spontaneously hindered. The in-situ sulfite treatment inactivated pathogens and improved the sludge dewatering properties. The relative abundances of SCFAs-production microbial were stimulated, facilitating the sludge bioconversion. The produced SCFAs from in-situ sulfite side-stream treatment could be applied as an "internal carbon source" to enhance biological nutrient removal to improve economic and environmental value from sludge treatment.

Enhancing anaerobic fermentation of waste activated sludge by investigating multiple electrochemical pretreatment conditions: Performance, modeling and microbial dynamics.

Electrochemical pretreatment (EPT) is an efficient technology to improve volatile fatty acids (VFAs) production during anaerobic fermentation of waste activated sludge (WAS). This study investigated the co-effects of different current intensities, electrolyte NaCl dosage and pretreatment time for promoting VFAs production. The results showed that it was considerably enhanced by 51.6 % when EPT was performed at 1.0 A, 1.0 g/L and 60 min, and response surface methodology strategy adjusted the optimal EPT conditions to 1.0 A, 1.2 g/L and 66 min. The potential mechanisms were proposed that EPT at optimal conditions greatly enhanced solubilization and hydrolysis of WAS and selectively inactivated methanogens, causing the enrichment of acidogenic bacteria (i.e., Lactobacillus, Saccharimonadales, Tetrasphaera and Prevotella) due to generated reactive chlorine species. Finally, the economic analysis indicated the promising application potential with the profit of EPT at optimal conditions increasing by 36.0 %.

Evaluation on leachability of heavy metals from tailings: risk factor identification and cumulative influence.

The leachability of heavy metals (HMs) in tailings is significantly affected by multivariate factors associated with environmental conditions. However, the leaching patterns of HMs in molybdenum (Mo) tailings due to environmental change and cumulative influences of multi-leaching factors remain unclear. The leaching behaviors of HMs in Mo tailings were studied through static leaching tests. The key leaching factors were discussed via simulating acid rain leaching scenario in terms of global and local environmental conditions. The potential risk factors were identified, and their cumulative influences on the leachability of HMs were evaluated with boosted regression trees (BRT) and generalized additive model (GAM) analyses. Environmental factors showed interactive effects on the leachability of HMs in tailings. The leachability of HMs in tailings decreased significantly with the interaction of increasing liquid/solid (L/S) ratio and pH. Rebound of leachability was observed with high L/S ratio (> 60) and long-time leaching (> 30 h). L/S ratio and pH were the most sensitive factors to the leachability of HMs with the corresponding contribution of 40.8% and 27.1%, respectively, followed by leaching time and temperature (~ 16%). The total contribution of global climate-associated factors, i.e., L/S ratio, leaching time, and temperature to the leachability of HMs was up to 70%, while leachate pH shared the other 30%. With the increase of persistent heavy rain in summer globally, As and Cd were found to having higher leaching risks than the other HMs in tailings, although an obvious decrease in their leachability was obtained due to the improvement of acid rain pollution in China. The study provides a valuable method for the identification of potential risk factors and their associations with the leaching behaviors of HMs in tailings under the background of obvious improvement on acid rain pollution in China and global climate change.

Thiosulfate pretreatment enhancing short-chain fatty acids production from anaerobic fermentation of waste activated sludge: Performance, metabolic activity and microbial community.

A novel strategy based on thiosulfate pretreatment for enhancing short-chain fatty acids (SCFAs) from anaerobic fermentation (AF) of waste activated sludge (WAS) was proposed in this study. The results showed that the maximal SCFA yield increased from 206.1 ± 4.7 to 1097.9 ± 17.2 mg COD/L with thiosulfate dosage increasing from 0 to 1000 mg S/L, and sulfur species contribution results revealed that thiosulfate was the leading contributor to improve SCFA yield. Mechanism exploration disclosed that thiosulfate addition largely improved WAS disintegration, due to thiosulfate serving as a cation binder for removing organic-binding cations, especially Ca2+ and Mg2+, dispersing the extracellular polymeric substance (EPS) structure and further entering into the intracellularly by stimulated carrier protein SoxYZ and subsequently caused cell lysis. Typical enzyme activities and related functional gene abundances indicated that both hydrolysis and acidogenesis were remarkably enhanced while methanogenesis was substantially suppressed, which were further strengthened by the enriched hydrolytic bacteria (e.g. C10-SB1A) and acidogenic bacteria (e.g. Aminicenantales) but severely reduced methanogens (e.g. Methanolates and Methanospirillum). Economic analysis confirmed that thiosulfate pretreatment was a cost-effective and efficient strategy. The findings obtained in this work provide a new thought for recovering resource through thiosulfate-assisted WAS AF for sustainable development.