3D chrysanthemum-like g-C3N4/TiO2 as an efficient visible-light-driven Z-scheme hybrid photocatalyst for tetracycline degradation.

Utilization of a solar-driven semiconductor as a photocatalyst to degrade antibiotic pollutants is a feasible and environmentally friendly technology. In this paper, 3D chrysanthemum-like g-C3N4/TiO2 as a visible-light-driven hybrid photocatalyst with a Z-scheme heterostructure was firstly synthesized by the in situ hydrothermal synthesis method. Experiments proved that this 3D chrysanthemum-like g-C3N4/TiO2 had better degradation performance toward tetracycline than TiO2 and g-C3N4. In particular, when optimized g-C3N4/TiO2-2 was applied for tetracycline removal (200 ml, 10 mg L-1), the corresponding degradation efficiency could reach nearly 100% within 60 min. The improved photocatalytic activity was the result of better utilization of the heterostructure-induced visible light, more efficient charge transfer in the Z-scheme heterojunction as well as stronger redox capability. The Z-scheme degradation mechanism was supported by the trapping experiments of active species and ESR radical detection, and the whole photocatalytic process was controlled by the combined action of ˙O2-, h+ and ˙OH radicals. This study may be beneficial for the design of more efficient sunlight-driven hybrid photocatalysts and their applications in wastewater treatment.

Construction of a type-II BiVO4/BiOI heterojunction for efficient photoelectrocatalytic degradation of ß-naphthol and coal gasification wastewater under visible-light irradiation.

Herein, a novel type-II BiVO4/BiOI (BVOI) heterojunction electrode material was successfully fabricated by using a facile two-step electrodeposition approach. The experimental results revealed that BiOI nanosheets were deposited onto the surface of BiVO4 particles successfully, with the special morphology providing more active sites, which was beneficial to the improvement of PEC performance. According to the electrochemical performance tests, it could be observed that the construction of a heterojunction effectively promoted the separation of photoinduced electron-hole pairs and increased the transfer rate of surface charges. Under visible-light irradiation, the BVOI-300 photoanode possessed the highest PEC ß-naphthol degradation rate at pH = 7, which approximately reached 82%, whose corresponding kinetic constant was 1.4 and 1.5 times higher than those of pure BiVO4 and BiOI. After five cycles, the degradation rate still remained at 64.61%. The band structure of the BVOI electrode was deduced, and the PEC mechanism of the BVOI electrode was investigated through the radical trapping quenching experiments and ESR test, which indicated that the ˙OH, h+ and ˙O2- radicals were crucial active species in the PEC ß-naphthol degradation process. For the BVOI-300 working electrode, the TOC content of coal gasification wastewater (CGW) decreased from 94.44 to 54.4 mg L-1, and the removal rate reached 42.4%. GC-MS was used to identify the organic components of coal gasification wastewater, which was expected to provide reference for remedying actual gasification wastewater containing refractory organic pollutants and offer a new development direction for the treatment of actual coal chemical wastewater.

Reclamation of waste coal gangue activated by Stenotrophomonas maltophilia for mine soil improvement: Solubilizing behavior of bacteria on nutrient elements.

The coal gangue has occupied the farmland and caused severe pollution to the surrounding environment, which was discharged with vast amount as a by-product of coal mining and washing. A sustainable and ecological microorganism activation method was proposed to disposal coal gangue as mineral fertilizer. A Stenotrophomonas maltophilia YZ1 bacteria was separated and found to be useful in solubilizing nutrient elements in coal gangue. The contents of available P, available K and available Si in the treated coal gangue reached 278.4 mg/kg, 1305.3 mg/kg and 522.7 mg/kg, respectively. The YZ1 bacteria dissolved the minerals of monetite (CaHPO4), muscovite and annite by the organic acids, which were the metabolism product of YZ1 bacteria. The solubilizing mechanisms of phosphate minerals included the release of protic and the chelation of organic acid with calcium. The microbial activation method can provide nutrient elements for soil, which may realize the reclamation of coal gangue in a harmless way.

A Simple Route to Produce Highly Efficient Porous Carbons Recycled from Tea Waste for High-Performance Symmetric Supercapacitor Electrodes.

High-performance porous carbons derived from tea waste were prepared by hydrothermal treatment, combined together with KOH activation. The heat-treatment-processed materials possess an abundant hierarchical structure, with a large specific surface of 2235 m2 g-1 and wetting-complemental hydrophilicity for electrolytes. In a two-electrode system, the porous carbon electrodes' built-in supercapacitor exhibited a high specific capacitance of 256 F g-1 at 0.05 A g-1, an excellent capacitance retention of 95.4% after 10,000 cycles, and a low leakage current of 0.014 mA. In our work, the collective results present that the precursor crafted from the tea waste can be a promising strategy to prepare valuable electrodes for high-performance supercapacitors, which offers a practical strategy to recycle biowastes into manufactured materials in energy storage applications.

Advances in aptamer screening and aptasensors' detection of heavy metal ions.

Heavy metal pollution has become more and more serious with industrial development and resource exploitation. Because heavy metal ions are difficult to be biodegraded, they accumulate in the human body and cause serious threat to human health. However, the conventional methods to detect heavy metal ions are more strictly to the requirements by detection equipment, sample pretreatment, experimental environment, etc. Aptasensor has the advantages of strong specificity, high sensitivity and simple preparation to detect small molecules, which provides a new direction platform in the detection of heavy metal ions. This paper reviews the selection of aptamers as target for heavy metal ions since the 21th century and aptasensors application for detection of heavy metal ions that were reported in the past five years. Firstly, the selection methods for aptamers with high specificity and high affinity are introduced. Construction methods and research progress on sensor based aptamers as recognition element are also introduced systematically. Finally, the challenges and future opportunities of aptasensors in detecting heavy metal ions are discussed.

Extraction and removal of vanadium by adsorption with resin 201*7 from vanadium waste liquid.

Resin 201*7 was used to extract and remove vanadium from vanadium waste liquid (VWL). More than 99% of vanadium was adsorbed from the VWL under the condition of resin dosage of 1.6 g/L, pH value of 6.0-8.0, temperature of 40 °C and adsorption time of 20 min. More than 99% of vanadium could be separated from other impurity ions in the VWL. The pure resin 201*7 and loaded resin were analyzed by infrared spectroscopy. The result shows that the resin 201*7 could selectively adsorb vanadium from the VWL. The adsorption process was analyzed with adsorption kinetics and adsorption isotherm curve. The adsorption process was more fitted with pseudo-second adsorption kinetic model and the adsorption isotherm was according to Langmuir isotherm model, respectively.

The Role of Nanotechnology in Food Safety: Current Status and Future Perspective.

Nanotechnology is an emerging science in food production and processing sector, yet the role of nanotechnology in food safety has not been comprehensively reviewed. This study reviewed the types, sources and mode of actions of the nanoparticles used in the food systems. Additionally, the effect of nanoparticles on animal health and safety of the products of animal origin was evaluated. Moreover, retention of nutritionally important nanoparticle minerals in the animal systems and foods of animal origins was analyzed. Furthermore, food safety was critically evaluated in terms of antioxidative ability, antibacterial properties, and toxicological studies. Finally, the scope of nanoparticle-based functional foods and shelf-life enhancement using active packaging was discussed. The article concluded that although significant research has been done on the use of nanoparticles in food systems, yet commercialization of nanoparticle-based foods needs further investigation.

Hierarchical nanosheet-based Ni3S2 microspheres grown on Ni foam for high-performance all-solid-state asymmetric supercapacitors.

The hierarchical nanosheet-based Ni3S2 microspheres directly grew on Ni foam using a two-step hydrothermal method. The microsphere with a diameter of ∼1 microns and a rough surface was well connected to each other without any binders to provide a larger specific surface area, shorter ion/electron diffusion paths, richer electroactive sites as a supercapacitor electrode. As a three-electrode supercapacitor, it delivers a high specific capacity of 981.8 F g-1 at 2 A g-1, an excellent rate capability of 436.4 F g-1 at 12 A g-1, and a good cycling stability of 950.9 F g-1 with 96.9% retention after 1000 cycles at 2 A g-1. Furthermore, an asymmetric supercapacitor based on Ni3S2-microsphere as a positive electrode and active carbon as a negative electrode shows a high energy density of 29.4 Wh kg-1 at 324.5 W kg-1 and a high power density of 3197.6 W kg-1 at 15.1 Wh kg-1. This work demonstrates that nanosheet-based Ni3S2 microspheres coated Ni foam can be an effective electrode for a real supercapacitor.

Utilization of Microcapsule Technology in Foods.

Microencapsulation technology has greatly accelerated the development of food industry and has a bright future for further applications. In this review paper, we introduce the current researches, latest advances and trends of core materials, wall materials, microencapsulation technology, as well as the encapsulation of food additives, bioactive substance, esculent oils, probiotics and other substances, and their application in food industry.

Methoxy poly(ethylene glycol) conjugated doxorubicin micelles for effective killing of cancer cells.

Methoxy poly(ethylene glycol) conjugated doxorubicin (mPEG-DOX) micelles are prepared for delivering drug effectively. The core of the unimolecular micelle is a DOX (doxorubicin) which is an anti-cancer chemotherapy drug, while the outer hydrophilic shell is composed of poly(ethylene glycol) (PEG) segments. Dynamic light scattering (DLS) analysis shows that the unimolecular micelles are uniform with a mean hydrodynamic diameter around 250 nm. The mPEG-DOX micelles can be internalized by the cancer cells and exhibit good cell uptake by the fluorescence microscopy. Obvious cytotoxicity is also observed when the concentration (count on DOX) is over 1 µg/mL. These findings indicate that these unique unimolecular micelles may offer a very promising approach for targeted cancer therapy.

Synthesis of LiYF4:Yb, Er upconversion nanoparticles and its fluorescence properties.

LiYbF4:Yb, Er nanoparticles have been successfully synthesized by thermal decomposition of multiple trifluoroacetic acid salts. The SEM and TEM results show the size of the LiYF4:Yb, Er nanoparticles is about 100 nm in diagonal line, and the morphology of the LiYF4:Yb, Er nanoparticles is highly uniform with octahedral structure. Under the excitation of 980 nm, the LiYF4:Yb, Er nanoparticles have higher upconversion luminescence efficiency compared with that of NaYF4:Yb, Er. The results indicate that the as-prepared LiYbF4:Yb, Er nanoparticles may have potential applications in bio-probes and displays.

Preparation of high quality carbon nanotubes by catalytic pyrolysis of waste plastics using FeNi-based catalyst.

Plastic waste pollution is the serious environmental problem, and catalytic pyrolysis of waste plastics is an effective way to solve this problem. Carbon nanotubes (CNTs) are prepared by catalytic pyrolysis of low-density polyethylene (LDPE) waste plastics by one-stage method using iron nitrate and nickel nitrate as catalyst. The growth mechanism of CNTs is analyzed in detail. TPO, XRD, SEM and Raman analyses show that increasing Ni content contributes to the production of CNTs with good morphology and high graphitization degree. While the increasing Fe content contributes to improving the yield of CNTs. The outer and inner diameters of the FeNi12-CNTs-800 are about 21 nm and 8 nm with the length of 18.9 µm, respectively. LDPE pyrolysis gases are analyzed to determine that the primary carbon source required for CNTs growth is C2H4. The C2H4 adsorption and decomposition processes on FeNi alloys are performed to reveal the growth mechanism of CNTs, based on density functional theory calculation. Three kinds of the growth models are proposed to explain the difference of the CNTs tubular shape. FeNi12-CNTs-800 are used to remove microplastics from wastewater due to existence of magnetic. PVC can be quickly removed from wastewater with removal of 100 % at 20 min. This study provides an effective way for recycling and treatment of waste plastic.

An electrochemical aptasensor based on silver-thiolated graphene for highly sensitive detection of Pb2.

The presence of lead ions (Pb2+) in the environment not only leads to environmental contamination but also poses a significant risk to public health through their migration into food and drinking water. Therefore, the development of rapid and effective techniques for detection of trace amounts of Pb2+ is crucial for safeguarding both the environment and biosafety. In this study, an aptamer-based electrochemical sensor was developed for specific detection of Pb2+ by modifying a polylysine (PLL) coated silver-thiolated graphene (Ag-SH-G) nanocomposite (PLL/Ag-SH-G) on the surface of a glassy carbon electrode, which was further modified with gold nanoparticles (AuNPs) for attachment of aptamers (Apt) that specifically recognized Pb2+. The Ag-SH-G particles were synthesized using a one-step in situ method, resulting in significantly enhanced electrochemical properties upon incorporating Ag nanoparticles into the PLL/Ag-SH-G composite. Coating of the covalently or no-covalently bonded Ag-SH-G particles with PLL provides an excellent supporting matrix, facilitating the assembly of AuNPs and a thiol-modified aptamer for Pb2+. Under optimized conditions, Apt/AuNPs/PLL/Ag-SH-G/GCE exhibited excellent sensing performance for Pb2+ with a wide linear response range (10-1000 nM), a low detection limit (0.047 nM) and extraordinary selectivity. The sensor was employed and satisfactory results were obtained in river water, soil and vegetable samples for the detection of Pb2+.

Ultrasensitive, Label-Free Voltammetric Detection of Dibutyl Phthalate Based on Poly-l-lysine/poly(3,4-ethylenedioxythiophene)-porous Graphene Nanocomposite and Molecularly Imprinted Polymers.

Development of an efficient technique for accurate and sensitive dibutyl phthalate (DBP) determination is crucial for food safety and environment protection. An ultrasensitive molecularly imprinted polymers (MIP) voltammetric sensor was herein engineered for the specific determination of DBP using poly-l-lysine/poly(3,4-ethylenedioxythiophene)/porous graphene nanocomposite (PLL/PEDOT-PG) and poly(o-phenylenediamine)-imprinted film as a label-free and sensing platform. Fabrication of PEDOT-PG nanocomposites was achieved through a simple liquid-liquid interfacial polymerization. Subsequently, poly-l-lysine (PLL) functionalization was employed to enhance the dispersibility and stability of the prepared PEDOT-PG, as well as promote its adhesion on the sensor surface. In the presence of DBP, the imprinted poly(o-phenylenediamine) film was formed on the surface of PLL/PEDOT-PG. Investigation of the physical properties and electrochemical behavior of the MIP/PLL/PEDOT-PG indicates that the incorporation of PG into PEDOT, with PLL uniformly wrapping its surface, significantly enhanced conductivity, carrier mobility, stability, and provided a larger surface area for specific recognition sites. Under optimal experimental conditions, the electrochemical response exhibited a linear relationship with a logarithm of DBP concentration within the range of 1 fM to 5 µM, with the detection limit as low as 0.88 fM. The method demonstrated exceptional stability and repeatability and has been successfully applied to quantify DBP in plastic packaging materials.

Hybrid supercapacitors using metal-organic framework derived nickel-sulfur compounds.

HYPOTHESIS: Metal-organic frameworks (MOFs) are highly suitable precursors for supercapacitor electrode materials owing to their high porosity and stable backbone structures that offer several advantages for redox reactions and rapid ion transport. EXPERIMENTS: In this study, a carbon-coated Ni9S8 composite (Ni9S8@C-5) was prepared via sulfuration at 500 ℃ using a spherical Ni-MOF as the sacrificial template. FINDING: The stable carbon skeleton derived from Ni-MOF and positive structure-activity relationship due to the multinuclear Ni9S8 components resulted in a specific capacity of 278.06 mAh·g-1 at 1 A·g-1. Additionally, the hybrid supercapacitor (HSC) constructed using Ni9S8@C-5 as the positive electrode and the laboratory-prepared coal pitch-based activated carbon (CTP-AC) as the negative electrode achieved an energy density of 69.32 Wh·kg-1 at a power density of 800.06 W·kg-1, and capacity retention of 83.06 % after 5000 cycles of charging and discharging at 5 A·g-1. The Ni-MOF sacrificial template method proposed in this study effectively addresses the challenges associated with structural collapse and agglomeration of Ni9S8 during electrochemical reactions, thus improving its electrochemical performance. Hence, a simple preparation method is demonstrated, with broad application prospects in supercapacitor electrodes.

Fixating lead in coal gangue with phosphate using phosphate-dissolving bacteria: Phosphorus dissolving characteristics of bacteria and adsorption mechanism of extracellular polymer.

Controlling and preventing lead pollution is currently the focus of environmental remediation. Coal gangue contains large quantities of lead, and its environmental impact cannot be ignored. This study investigated the tolerance of Stenotrophomonas maltophilia (YZ-1 train) to lead ion and its fixation effect on lead in coal gangue. The fixation mechanism of lead ions by using the YZ-1 train was studied with CaHPO4 and Ca3(PO4)2. The tolerance mechanism and fixation characteristics of the three bacterial extracellular polymers and cell components to lead were analyzed. The results show that the YZ-1 train had a strong resistance to lead ions. The amount of lead released from coal gangue can be reduced by up to 91.1% upon treatment with the YZ-1 train, which can dissolve phosphate minerals to form stable hydroxyapatite (Pb5(PO4)3(OH)) and pyromorphite (Pb5(PO4)3Cl) with lead ions. Tryptophan and tyrosine from cellular components and extracellular polymers with loosely and tightly bound proteins are the main participants in the fixation of lead ions. The by-products of soluble microbes affect the fixation of lead ions in soluble extracellular polymers. The carboxylic acids and carboxylates secreted by bacteria are involved in the adsorption and fixation of lead ions.

Stable lithium metal anode enabled by in situ formation of a Li3N/Li-Bi alloy hybrid layer.

A hybrid protective layer containing a Li3N and Li-Bi alloy is fabricated on a Li-metal anode as an artificial SEI layer to guide dendrite-free Li deposition. Noteworthily, the hybrid interface could not only facilitate homogeneous Li plating but also provide rapid Li+ transportation, enabling a long-term stability of ∼2400 h at 0.5 mA cm-2 with a low steady overpotential of 10 mV.

Preparation of pyrolysis products by catalytic pyrolysis of poplar: Application of biochar in antibiotic wastewater treatment.

Poplar waste is acted as feedstock to produce renewable biofuel and green chemical by catalytic pyrolysis using ferric nitrate and zinc chloride as additive. The additive contributes to the generation of furfural in bio-oil. Additive promotes the generation of H2 and inhibits the generation of CO with bio-gas heating value of 12.16 MJ (Nm3)-1. Biochar exists ZnO and Fe3O4 with large surface area, which could be used as absorbent and photocatalyst for tetracycline and ciprofloxacin removal. The tetracycline and ciprofloxacin adsorption amount of biochar are 316.41 and 255.23 mg g-1 respectively. While the photocatalytic degradation removal of the tetracycline and ciprofloxacin is close to 100%. The adsorption and photocatalytic degradation mechanism are investigate and analyzed using the density functional theory and electron paramagnetic resonance analysis. Biochar can be quickly recycled and regenerated after use. Besides, biochar can be used in lithium ion battery industry for energy storage, which specific capacity is 535 mAh g-1.

An Effective Strategy to Synthesize Well-Designed Activated Carbon Derived from Coal-Based Carbon Dots via Oxidation before Activation with a Low KOH Content as Supercapacitor Electrodes.

The development of coal-based activated carbon for supercapacitors provides a robust and effective approach toward the clean and efficient use of coal, and it also offers high-quality and low-cost raw materials for energy storage devices. However, the one-step activation method for preparing coal-based activated carbon has problems, such as difficulty in introducing surface-functional groups and high KOH dosage. In our work, activated carbon was prepared through an effective strategy of oxidation and KOH activation with a low KOH content by employing coal-based carbon dots as raw material. The influence of temperature during the KOH activation of carbon dots on a specific surface area, pore structure, and various quantities and types of surface-functional groups, as well as on the electrochemical performance of supercapacitors, was systematically studied. The as-prepared sample, with the alkali-carbon ratio of 0.75, processes a large specific surface area (1207 m2 g-1) and abundant surface-functional groups, which may provide enormous active sites and high wettability, thus bringing in high specific capacitance and boosted electrochemical performances. The oxygen and nitrogen content of the activated carbon decreases while the carbon content increases, and the activation temperature also increases. The as-prepared activated carbon reaches the highest specific capacitance of 202.2 F g-1 in a 6 M KOH electrolyte at a current density of 10 A g-1. This study provides new insight into the design of high-performance activated carbon and new avenues for the application of coal-based carbon dots.

Neuroprotective effects of PRG on Aß25-35-induced cytotoxicity through activation of the ERK1/2 signaling pathway.

ETHNOPHARMACOLOGICAL RELEVANCE: Phylloporia ribis (Schumach:Fr.)Ryvarden is a genus of needle Phellinus medicinal fungi, parasitic on the living rhizomes of hawthorn and pear trees. As a traditional Chinese medicine, Phylloporia ribis was used in folklore for long-term illness, weakness and memory loss in old age. Previous studies have shown that polysaccharides from Phylloporia ribis (PRG) significantly promoted synaptic growth in PC12 cells in a dose-dependent manner, exhibiting "NGF"-like neurotrophic activity. Aß25-35 damage to PC12 cells produced neurotoxicity and decreased cell survival, and PRG reduced the apoptosis rate, suggesting that PRG has neuroprotective effects. The studies confirmed that PRG had the potential to be a neuroprotective agent, but its neuroprotective mechanism remained unclear. AIM OF THE STUDY: We aimed to elucidate the neuroprotective effects of PRG in an Aß25-35-induced Alzheimer's disease (AD) model. MATERIALS AND METHODS: Highly-differentiated PC12 cells were treated with Aß25-35 (AD model) and PRG, and were assessed for cellular apoptosis, inflammatory factors, oxidative stress, and kinase phosphorylation. RESULTS: The results showed that the PRG groups effectively inhibited the neurotoxicity, mainly manifested by inhibiting mitochondrial oxidative stress, attenuating neuroinflammatory responses, and improving mitochondrial energy metabolism, eventually resulting in higher cell survival. The expression of p-ERK, p-CREB and BDNF proteins was increased in the PRG groups compared to the model group, which confirmed that PRG reversed the inhibition of the ERK pathway. CONCLUSION: We provide evidence for neuroprotection conferred by PRG and its mechanism by inhibiting ERK1/2 hyper-phosphorylation, prevention of mitochondrial stress, and subsequent prevention of apoptosis. The study highlights PRG as a promising candidate with neuroprotective effects, the potential of which can be harnessed for identifying novel therapeutic targets.