RESUMO
OBJECTIVE: Stress distribution assessment by finite elements analysis in poly(etheretherketone) (PEEK) implant and abutment as retainers of single crowns in the anterior region. MATERIALS AND METHODS: Five 3D models were created, varying implant/abutment manufacturing materials: titanium (Ti), zirconia (Zr), pure PEEK (PEEKp), carbon fiber-reinforced PEEK (PEEKc), glass fiber-reinforced PEEK (PEEKg). A 50 N load was applied 30o off-axis at the incisal edge of the upper central incisor. The Von Mises stress (σvM) was evaluated on abutment, implant/screw, and minimum principal stress (σmin) and maximum shear stress (τmax) for cortical and cancellous bone. RESULTS: The abutment σvM lowest stress was observed in PEEKp group, being 70% lower than Ti and 74% than Zr. On the implant, PEEKp reduced 68% compared to Ti and a 71% to Zr. In the abutment screws, an increase of at least 33% was found in PEEKc compared to Ti, and of at least 81% to Zr. For cortical bone, the highest τmax values were in the PEEKp group, and a slight increase in stress was observed compared to all PEEK groups with Ti and Zr. For σmin, the highest stress was found in the PEEKc. Stress increased at least 7% in cancellous bone for all PEEK groups. CONCLUSION: Abutments and implants made by PEEKc concentrate less σvM stress, transmitting greater stress to the cortical and medullary bone. CLINICAL RELEVANCE: The best stress distribution in PEEKc components may contribute to decreased stress shielding; in vitro and in vivo research is recommended to investigate this.
Assuntos
Benzofenonas , Coroas , Dente Suporte , Análise do Estresse Dentário , Análise de Elementos Finitos , Cetonas , Teste de Materiais , Polietilenoglicóis , Polímeros , Titânio , Zircônio , Cetonas/química , Polietilenoglicóis/química , Humanos , Zircônio/química , Titânio/química , Fibra de Carbono/química , Projeto do Implante Dentário-Pivô , Incisivo , Materiais Dentários/química , Implantes Dentários para Um Único Dente , Osso Cortical , Vidro/química , Planejamento de Prótese DentáriaRESUMO
PURPOSE: To investigate the influence of different denture-bearing conditions on the masticatory function and patient-reported outcome measures (PROMs) of complete denture wearers. METHODS: Sixty edentulous patients were selected and allocated into two groups according to the American College of Prosthodontics' (ACP) classification: non-atrophic (NAT) (Classes I and II) (n = 24) and atrophic (AT) (Classes III and IV) (n = 36). All patients received new complete dentures (CDs). The objective variables (masticatory performance and swallowing threshold) were assessed as well as the PROMs (oral health-related quality of life (OHIP-EDENT), patient satisfaction) and quality of the prosthesis, at baseline (using the old CD) and after 4 months new prostheses use. Data were analyzed by Mann-Whitney test followed by the Generalized Equations Estimation (GEE), linear regression and Chi-square test. RESULTS: Higher masticatory performance was observed in the NAT group (p < .05) for both time points, baseline and after 4 months. However, compared to baseline, both groups showed significant masticatory improvement after 4 months (p < .05). Satisfaction and overall quality of life improved after 4 months with no difference between groups (p > .05). Regarding the quality of the CD, baseline results were significantly (p < .05) lower in the AT group, but after 4 months, no significant differences were found between groups and in intragroup analysis (p > .05). CONCLUSIONS: The denture-bearing conditions seems to impact masticatory function, but the PROMs are barely affected.
RESUMO
OBJECTIVE: This study aimed to investigate changes in the surface characteristics of two denture resins when disinfected with a vinegar-hydrogen peroxide (VHP) mixture. MATERIALS AND METHODS: Microwave-polymerized or 3D printed acrylic resin disks were immersed for 900 min (simulating 90 daily uses) in the following solutions (N = 10): water; 0.5% sodium hypochlorite; hydrogen peroxide and water dilution (1:1 ratio); vinegar and water dilution (1:1 ratio); and VHP mixture. Surface roughness, Knoop microhardness, surface free energy, and scanning electron microscopic images were assessed before and after the immersions. Results were compared using the 2-way ANOVA for repeated measures and Tukey test, at 5% significance. RESULTS: Surface roughness and microhardness did not differ (P > .05) among the solutions and times. Surface free energy and its dispersive component increased (P < .05) for all solutions. All solutions, except for water and VHP mixture, degraded microtopography. CONCLUSIONS: The VHP mixture was not deleterious to conventional and 3D-printed resin surfaces. CLINICAL RELEVANCE: Conventional and 3D printed resin dentures can be disinfected with a VHP mixture in a 1:1 ratio because this mixture does not substantially affect the surface characteristics after 90 daily immersions. On the contrary, sodium hypochlorite, hydrogen peroxide, and vinegar solutions, even in low concentrations, should be used with caution for denture disinfection because they may alter the resin microtopography over time.
Assuntos
Ácido Acético , Desinfecção , Peróxido de Hidrogênio , Hipoclorito de Sódio , Resinas Acrílicas , Água , DentadurasRESUMO
STATEMENT OF PROBLEM: Conventional analog methods have been replaced with digital methods for removable partial denture (RPD) frameworks. However, limited information is available regarding the build direction of RPD frameworks and its effect on properties. PURPOSE: The purpose of this in vitro study was to evaluate the mechanical and surface properties of the cobalt chromium (Co-Cr) alloy produced at different build angles by the laser powder bed fusion additive manufacturing (AM) technology used for RPD framework fabrication. MATERIAL AND METHODS: Plate-shaped Co-Cr specimens (n=6) were produced by the AM technology and divided into 3 groups depending on the build angle (0, 45, or 90 degrees). The elastic modulus and fracture properties were evaluated by flexural testing. Additionally, 15 disks were printed by using the same parameters of the plates (n=5) to analyze the surface hardness with microhardness testing, and surface properties were determined by surface free energy by using the contact angle and surface roughness measured by using a profilometer. Twelve Co-Cr cylindrical specimens were produced by using the same parameters (n=4), and their microstructure was examined by using an optical microscope. One-way ANOVA was used to evaluate the overall effects of the interaction between groups, and the Tukey test was applied when the interaction was statistically significant (α=.05). RESULTS: The flexural strength showed a statistically significant difference (P<.05), with the peak value exhibited by the 0-degree group. A statistical difference was also observed between the angulation and modulus of elasticity; however, the highest value was exhibited by the 45-degree group. For the fracture topography, all groups observed a dimple-like fracture, although the 45-degree group showed wider cleavage planes of fractures than other angulations. For microhardness, the 0- and 45-degree groups exhibited a statistical difference in relation to the 90-degree group (P<.05). For surface properties, no statistically significant difference (P>.05) was found in any of the evaluated parameters. Dependence on the build angles was evidenced by the molten pool boundaries during observation of the microstructure. CONCLUSIONS: The build angle influenced the flexural strength and microhardness of the Co-Cr alloy produced by AM; however, it does not affect surface free energy and surface roughness.
Assuntos
Prótese Parcial Removível , Ligas de Cromo/química , Elasticidade , Módulo de Elasticidade , Propriedades de Superfície , Teste de MateriaisRESUMO
STATEMENT OF PROBLEM: The simplified technique has been recommended for the fabrication of removable complete dentures. However, a consensus regarding the performance of the simplified and the traditional techniques is lacking. PURPOSE: The purpose of this randomized clinical trial was to compare the performance of prostheses fabricated with the simplified and the traditional techniques. MATERIAL AND METHODS: Sixty participants were recruited and randomized into 2 groups: traditional technique (control group) and simplified technique (experimental group). The assessments were performed before treatment (baseline) and 2 and 4 months after adaptation to the new complete dentures. The variables evaluated were satisfaction, oral health-related quality of life (OHRQoL) by using the Brazilian version of the OHIP-EDENT, the quality of the prostheses, and, for the functional assessment, the masticatory performance and swallowing threshold. The data were analyzed by the Fisher exact test, the Mann-Whitney test, and the generalized equations estimating (GEE) method. RESULTS: At baseline, the mean ±standard deviation quality of the prostheses was 5.3 ±2.3 for the traditional technique and 4.9 ±2.3 for the simplified technique, and at 4 months, it was 9.3 ±0.9 and 9.1 ±0.9, respectively. For masticatory performance, the mean ±standard deviation X50 at baseline was 5.7 ±1.4 for the traditional technique and 5.7 ±0.9 for the simplified technique, and at 4 months, it was 3.8 ±1.2 and 3.7 ±0.9, respectively. The mean ±standard deviation OHRQoL at baseline was 14.1 ±8.6 for the traditional technique and 12.5 ±9.4 for the simplified technique, and at 4 months, it was 3.2 ±4.3 and 2.6 ±5.1, respectively. The mean ±standard deviation satisfaction at baseline was 9.5 ±3.9 for the traditional technique and 9.3 ±4.2 for the simplified technique; after 4 months, it was 14.8 ±2.0 for both techniques. There was a significant improvement (P<.05) for all variables in the study when comparing them at the baseline to those at the evaluation after provision of new complete dentures. There was no significant difference in all analyzed variables (P>.05) between the 2 techniques for prosthesis fabrication. CONCLUSIONS: The simplified technique appears to be a suitable alternative to the traditional technique for the fabrication of complete dentures, with similar performance.
Assuntos
Satisfação do Paciente , Qualidade de Vida , Humanos , Prótese Total , Prótese Parcial , Brasil , MastigaçãoRESUMO
Whilst Candida albicans occurs in peri-implant biofilms, its role in peri-implantitis remains unclear. This study therefore examined the virulence of C. albicans in mixed-species biofilms on titanium surfaces. Biofilms of C. albicans (Ca), C. albicans with streptococci (Streptococcus sanguinis, S. mutans) (Ca-Ss-Sm) and those incorporating Porphyromonas gingivalis (Ca-Pg and Ca-Ss-Sm-Pg) were developed. Expression of C. albicans genes associated with adhesion (ALS1, ALS3, HWP1) and hydrolytic enzymes (SAP2, SAP4, SAP6, PLD1) was measured and hyphal production by C. albicans quantified. Compared with Ca biofilms, significant (p<0.05) up-regulation of ALS3, HWP1, SAP2 and SAP6, and hyphal production occurred in biofilms containing streptococci (Ca-Ss-Sm). In Ca-Pg biofilms, down-regulation of HWP1 and SAP4 expression, with reduced hyphal production occurred. Ca-Ss-Sm-Pg biofilms had increased hyphal proportions and up-regulation of ALS3, SAP2 and SAP6. In conclusion, C. albicans expressed virulence factors in biofilms that could contribute to peri-implantitis, but this was dependent on associated bacterial species.
Assuntos
Biofilmes/crescimento & desenvolvimento , Candida albicans , Hifas/crescimento & desenvolvimento , Porphyromonas gingivalis/fisiologia , Streptococcus sanguis/fisiologia , Titânio , Antibiose/genética , Candida albicans/patogenicidade , Candida albicans/fisiologia , Proteínas Fúngicas/genética , Humanos , Glicoproteínas de Membrana/genética , Peri-Implantite/microbiologia , Propriedades de Superfície , Virulência , Fatores de Virulência/metabolismoRESUMO
This study examined the influence of bacteria on the virulence and pathogenicity of candidal biofilms. Mature biofilms (Candida albicans-only, bacteria-only, C. albicans with bacteria) were generated on acrylic and either analysed directly, or used to infect a reconstituted human oral epithelium (RHOE). Analyses included Candida hyphae enumeration and assessment of Candida virulence gene expression. Lactate dehydrogenase (LDH) activity and Candida tissue invasion following biofilm infection of the RHOE were also measured. Candida hyphae were more prevalent (p < 0.05) in acrylic biofilms also containing bacteria, with genes encoding secreted aspartyl-proteinases (SAP4/SAP6) and hyphal-wall protein (HWP1) up-regulated (p < 0.05). Candida adhesin genes (ALS3/EPA1), SAP6 and HWP1 were up-regulated in mixed-species biofilm infections of RHOE. Multi-species infections exhibited higher hyphal proportions (p < 0.05), up-regulation of IL-18, higher LDH activity and tissue invasion. As the presence of bacteria in acrylic biofilms promoted Candida virulence, consideration should be given to the bacterial component when managing denture biofilm associated candidoses.
Assuntos
Bactérias , Biofilmes , Candida albicans/patogenicidade , Epitélio/microbiologia , Ácido Aspártico Proteases/genética , Candida albicans/crescimento & desenvolvimento , Proteínas Fúngicas/genética , Humanos , Hifas/crescimento & desenvolvimento , L-Lactato Desidrogenase/metabolismo , Mucosa Bucal/microbiologia , Estomatite sob Prótese/microbiologia , VirulênciaRESUMO
OBJECTIVES: To evaluate the effect of sodium hypochlorite (NaOCl) on biofilms, colour stability (ΔE) and surface roughness (Ra) of complete dentures and patient acceptability. BACKGROUND: Denture cleansers should be able to reduce the accumulation of biofilms without affecting the acrylic resin properties. Patient satisfaction is important to maintaining their daily use. MATERIALS AND METHODS: Fifteen participants were instructed to keep their dentures immersed daily in a 0.5% NaOCl solution for 3 min over 90 days. Swabs were taken from dentures and inoculated on CHROMagar and blood agar. The number of colony-forming units (cfu) was counted after a 48-h incubation period. ΔE was assessed using the CIE L*a*b* system. Ra was measured using a profilometer. Patient acceptability was checked based on their degree of satisfaction. Cell counts, ΔE and Ra were analysed using anova, Friedman's and Kruskal-Wallis tests, respectively (α = 0.05). RESULTS: A significant reduction in the total number of microorganisms (p = 0.001) and Candida spp. was noticed. No significant differences were found for ΔE (p = 0.68) and for Ra (p = 0.47). The level of the patient satisfaction increased throughout the follow-up period. CONCLUSION: The 0.5% NaOCl solution was effective in reducing microorganisms without significant changes in colour or roughness of denture resin. The participants reported satisfaction with the cleaning results.
Assuntos
Anti-Infecciosos Locais/química , Biofilmes/efeitos dos fármacos , Higienizadores de Dentadura/química , Prótese Total/microbiologia , Hipoclorito de Sódio/química , Resinas Acrílicas/química , Idoso , Bactérias/efeitos dos fármacos , Fenômenos Fisiológicos Bacterianos/efeitos dos fármacos , Candida/efeitos dos fármacos , Candida/fisiologia , Contagem de Colônia Microbiana , Feminino , Humanos , Masculino , Pessoa de Meia-Idade , Satisfação do Paciente , Saliva/microbiologia , Propriedades de Superfície/efeitos dos fármacosRESUMO
INTRODUCTION: The surface free energy of conditioned-dentin is one of the factors that interfere with monomeric infiltration of the interfibrillar spaces. Saturation of the tooth matrix with different substances may modulate this energy and, consequently, the wettability of the dentin. AIM: To evaluate the influence of different substances used to saturate conditioned-dentin on surface free energy (SFE) of this substrate. MATERIALS AND METHODS: Dentin blocks (4 × 7 × 1 mm, n = 6/ group), obtained from the roots of bovine incisors, were etched using phosphoric acid for 15 seconds, rinsed and gently dried. The surfaces were treated for 60 seconds with: ultra-purified water (H20-control); ethanol (EtOH), acetone (ACT), chlorhexidine (CHX), ethylenediaminetetraacetic acid (EDTA); or sodium hypochlorite (NaOCl). The tooth surfaces were once again dried with absorbent paper and prepared for SFE evaluation using three standards: water, formamide and bromonaphthalene. Analysis of variance (ANOVA) and Dunnet's tests (a = 0.05) were applied to the data. RESULTS: Ethylenediaminetetraacetic acid was the only substance that caused a change to the contact angle for the standards water and formamide, while only EtOH influenced the angles formed between formamide and the dentin surface. None of the substances exerted a significant effect for bromonaphtha-lene. In comparison to the control, only EDTA and NaOCl altered both polar components of the SFE. Total SFE was increased by saturation of the collagen matrix by EDTA and reduced when NaOCl was used. CONCLUSION: Saturation of the collagen matrix by EDTA and EtOH changed the surface free energy of the dentin. In addition, the use of NaOCl negatively interfered with the properties evaluated. CLINICAL SIGNIFICANCE: The increase of surface free energy and wettability of the dentin surface would allow higher penetration of the the adhesive system, which would be of importance to the clinical success of resin-dentin union.
Assuntos
Colágeno/efeitos dos fármacos , Dentina/efeitos dos fármacos , Irrigantes do Canal Radicular/farmacologia , Solventes/farmacologia , Acetona/farmacologia , Condicionamento Ácido do Dente/métodos , Animais , Bovinos , Clorexidina/farmacologia , Colágeno/ultraestrutura , Dentina/ultraestrutura , Ácido Edético/farmacologia , Etanol/farmacologia , Formamidas/química , Teste de Materiais , Naftalenos/química , Ácidos Fosfóricos/química , Hipoclorito de Sódio/farmacologia , Tensão Superficial , Água/química , MolhabilidadeRESUMO
Candida albicans colonizes sites with different environmental pH. However, it is unclear how these conditions can interfere on biofilms. This study aimed to evaluate the influence of environmental pH on behavior of C. albicans regarding its structure, virulence and susceptibility to fluconazole (FLZ). Minimal inhibitory concentration, minimal fungicidal concentration and time kill were used to evaluate the susceptibility to FLZ in planktonic cells under three pH values (4.0, 5.5, 7.0). These pH values were used for biofilms analysis. C. albicans ATCC 90028 was developed on poly(methlymethacrylate) resin for 48 h. Then, 2.56 µg/mL of FLZ was added to experimental groups for 24 h, and biofilms were analyzed by cell quantification, bioactivity, secretion of proteinases and phospholipases and structure. All data were analyzed by two-way ANOVA, followed by Tukey's test (α = 0.05). For planktonic cells, changes in environmental pH decreased the susceptibility to FLZ. C. albicans biofilms developed at pH 5.5 showed higher cell counts, bioactivity, bio-volume, average thickness and roughness coefficient (p < 0.05). In contrast, the presence of FLZ at pH 4.0 did not influence the structural parameters (p > 0.05), but increased secretion of proteinase and phospholipase (p < 0.05). Within the conditions studied, it was shown that environmental pH modulates the structure, virulence and susceptibility of C. albicans to FLZ.
Assuntos
Antifúngicos/farmacologia , Biofilmes/efeitos dos fármacos , Biofilmes/crescimento & desenvolvimento , Candida albicans/efeitos dos fármacos , Candida albicans/fisiologia , Fluconazol/farmacologia , Contagem de Colônia Microbiana , Concentração de Íons de Hidrogênio , Testes de Sensibilidade Microbiana , Viabilidade Microbiana/efeitos dos fármacosRESUMO
Although Streptococcus mutans biofilms have been useful for evaluating the cariogenic potential of dietary carbohydrates and the effects of fluoride on dental demineralization, a more appropriate biofilm should be developed to demonstrate the influence of other oral bacteria on cariogenic biofilms. This study describes the development and validation of a three-species biofilm model comprising Streptococcus mutans, Actinomyces naeslundii, and Streptococcus gordonii for the evaluation of enamel and dentin demineralization after cariogenic challenges and fluoride exposure. Single- or three-species biofilms were developed on dental substrata for 96 h, and biofilms were exposed to feast and famine episodes. The three-species biofilm model produced a large biomass, mostly comprising S. mutans (41%) and S. gordonii (44%), and produced significant demineralization in the dental substrata, although enamel demineralization was decreased by fluoride treatment. The findings indicate that the three-species biofilm model may be useful for evaluating the cariogenic potential of dietary carbohydrates other than sucrose and determining the effects of fluoride on dental substrata.
Assuntos
Actinomyces/fisiologia , Biofilmes/efeitos dos fármacos , Esmalte Dentário/microbiologia , Dentina/microbiologia , Streptococcus gordonii/fisiologia , Streptococcus mutans/fisiologia , Desmineralização do Dente/microbiologia , Actinomyces/efeitos dos fármacos , Fluoretos/farmacologia , Modelos Biológicos , Saliva/microbiologia , Streptococcus gordonii/efeitos dos fármacos , Streptococcus mutans/efeitos dos fármacosRESUMO
STATEMENT OF PROBLEM: Different surface treatment protocols of poly(methyl methacrylate) have been proposed to improve the adhesion of silicone-based resilient denture liners to poly(methyl methacrylate) surfaces. PURPOSE: The purpose of this study was to evaluate the effect of different poly(methyl methacrylate) surface treatments on the adhesion of silicone-based resilient denture liners. MATERIAL AND METHODS: Poly(methyl methacrylate) specimens were prepared and divided into 4 treatment groups: no treatment (control), methyl methacrylate for 180 seconds, acetone for 30 seconds, and ethyl acetate for 60 seconds. Poly(methyl methacrylate) disks (30.0 × 5.0 mm; n = 10) were evaluated regarding surface roughness and surface free energy. To evaluate tensile bond strength, the resilient material was applied between 2 treated poly(methyl methacrylate) bars (60.0 × 5.0 × 5.0 mm; n = 20 for each group) to form a 2-mm-thick layer. Data were analyzed by 1-way ANOVA and the Tukey honestly significant difference tests (α = .05). A Pearson correlation test verified the influence of surface properties on tensile bond strength. Failure type was assessed, and the poly(methyl methacrylate) surface treatment modifications were visualized with scanning electron microscopy. RESULTS: The surface roughness was increased (P < .05) by methyl methacrylate treatment. For the acetone and ethyl acetate groups, the surface free energy decreased (P < .05). The tensile bond strength was higher for the methyl methacrylate and ethyl acetate groups (P < .05). No correlation was found regarding surface properties and tensile bond strength. Specimens treated with acetone and methyl methacrylate presented a cleaner surface, whereas the ethyl acetate treatment produced a porous topography. CONCLUSION: The methyl methacrylate and ethyl acetate surface treatment protocols improved the adhesion of a silicone-based resilient denture liner to poly(methyl methacrylate).
Assuntos
Materiais Dentários/química , Reembasadores de Dentadura , Polimetil Metacrilato/química , Silicones/química , Acetatos/química , Acetona/química , Resinas Acrílicas/química , Adesividade , Colagem Dentária , Humanos , Teste de Materiais , Metilmetacrilato/química , Microscopia Eletrônica de Varredura , Porosidade , Elastômeros de Silicone/química , Solventes/química , Estresse Mecânico , Propriedades de Superfície , Tensão Superficial , Resistência à Tração , Fatores de TempoRESUMO
BACKGROUND: It is well known that the use of denture cleansers can reduce Candida albicans biofilm accumulation; however, the efficacy of citric acid denture cleansers is uncertain. In addition, the long-term efficacy of this denture cleanser is not well established, and their effect on residual biofilms is unknown. This in vitro study evaluated the efficacy of citric acid denture cleanser treatment on C. albicans biofilm recolonization on poly(methyl methacrylate) (PMMA) surface. METHODS: C. albicans biofilms were developed for 72 h on PMMA resin specimens (n = 168), which were randomly assigned to 1 of 3 cleansing treatments (CTs) overnight (8 h). CTs included purified water as a control (CTC) and two experimental groups that used either a 1:5 dilution of citric acid denture cleanser (CT5) or a 1:8 dilution of citric acid denture cleanser (CT8). Residual biofilms adhering to the specimens were collected and quantified at two time points: immediately after CTs (ICT) and after cleaning and residual biofilm recolonization (RT). Residual biofilms were analyzed by quantifying the viable cells (CFU/mL), and biofilm architecture was evaluated by confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). Denture cleanser treatments and evaluation periods were considered study factors. Data were analyzed using two-way ANOVA and Tukey's Honestly Significant Difference (HSD) test (α = 0.05). RESULTS: Immediately after treatments, citric acid denture cleansing solutions (CT5 and CT8) reduced the number of viable cells as compared with the control (p < 0.01). However, after 48 h, both CT groups (CT5 and CT8) showed biofilm recolonization (p < 0.01). Residual biofilm recolonization was also detected by CLSM and SEM analysis, which revealed a higher biomass and average biofilm thickness for the CT8 group (p < 0.01). CONCLUSION: Citric acid denture cleansers can reduce C. albicans biofilm accumulation and cell viability. However, this CT did not prevent biofilm recolonization.
Assuntos
Biofilmes/efeitos dos fármacos , Candida albicans/efeitos dos fármacos , Ácido Cítrico/farmacologia , Materiais Dentários/química , Higienizadores de Dentadura/farmacologia , Polimetil Metacrilato/química , Biofilmes/crescimento & desenvolvimento , Biomassa , Candida albicans/crescimento & desenvolvimento , Contagem de Colônia Microbiana , Película Dentária/fisiologia , Humanos , Técnicas In Vitro , Teste de Materiais , Viabilidade Microbiana , Microscopia Confocal , Microscopia Eletrônica de Varredura , Propriedades de Superfície , Fatores de Tempo , Água/químicaRESUMO
OBJECTIVE: This study evaluated the influence of the area of Candida albicans biofilm on denture disinfection by microwave energy. MATERIALS AND METHODS: Candida albicans biofilm was allowed to form for 72 h on resin discs, and three small coverage or seven large coverage discs were placed onto the palatal surface of sterile maxillary dentures. Each denture was immersed in 200 ml distilled water and individually irradiated at a power of 450, 630 or 900 W for different time intervals (1, 2 or 3 min) (n = 6). The effectiveness of disinfection was evaluated by counting the residual cells. The data were analysed by anova and Tukey's HSD test (α = 0.05). Pearson's correlation test was performed to determine the correlation between effectiveness of sterilisation and temperature. RESULTS: Dentures with a larger area of biofilm demanded a longer irradiation exposure to achieve disinfection (p < 0.001), irrespective of power setting, and in this time no yeast growth was detected. Dentures with small areas of biofilm were disinfected after 1 min at 900 W and 2 min at 450 or 630 W. A positive correlation was found between water temperature and effectiveness of disinfection (r = 0.6170; p < 0.001). CONCLUSION: The C. albicans biofilm area influenced disinfection by microwave energy; therefore dentures with larger biofilm areas required longer irradiation exposure to be disinfected.
Assuntos
Biofilmes/efeitos da radiação , Candida albicans/efeitos da radiação , Dentaduras/microbiologia , Desinfecção/métodos , Micro-Ondas/uso terapêutico , Contagem de Colônia Microbiana , Película Dentária/microbiologia , Humanos , Imersão , Teste de Materiais , Polimetil Metacrilato/química , Doses de Radiação , Método Simples-Cego , Propriedades de Superfície , Temperatura , Fatores de Tempo , Água/químicaRESUMO
STATEMENT OF PROBLEM: Although new materials have emerged as options to fabricate removable dental prostheses, the development of Candida biofilms on these materials and the effectiveness of methods to control these pathogenic biofilms are poorly understood. PURPOSE: The purpose of this study was to evaluate the efficacy of denture cleansers on Candida single- and dual-species biofilms formed on polyamide resin. MATERIAL AND METHODS: Polymethyl methacrylate (PMMA) resin (Acron MC) and polyamide resin (Flexite M.P.) specimens (n=116) were prepared, and their surface roughness was standardized (0.34 ±0.02 µm). Surface free energy (SFE) was measured for some specimens (n=20 per resin), while the remainder were randomly divided by lottery into 24 groups (n=8) for biofilm assay. C. albicans and/or C. glabrata biofilm was formed for 72 hours, and then specimens were treated with an enzymatic cleanser solution (Polident 3 Minutes), a cleanser solution (Corega Tabs), or 0.5% sodium hypochlorite (NaOCl) solution. Water served as the negative control. Remaining adherent microorganisms were removed from the treated specimens by ultrasonic waves, and colony-forming units (CFU) of each microorganism were calculated. SFE data were analyzed by 1-way ANOVA, and Candida species data were analyzed by 3-way ANOVA followed by the Tukey-Kramer test (P=.05). RESULTS: All tested biofilms displayed significantly higher growth on polyamide resin (P<.001), which presented the lowest SFE. Denture cleansers significantly decreased Candida levels; however, the 0.5% NaOCl solution was the only effective cleanser. C. glabrata revealed significantly higher CFU counts under all experimental conditions (P<.001). CONCLUSIONS: The highest Candida spp. biofilm growth was shown to occur on polyamide resin when compared with PMMA. Denture cleansers were able to remove Candida spp. biofilm formed on both denture base resins.
Assuntos
Biofilmes/efeitos dos fármacos , Candida/efeitos dos fármacos , Materiais Dentários/química , Higienizadores de Dentadura/farmacologia , Nylons/química , Polimetil Metacrilato/química , Resinas Acrílicas/química , Biofilmes/crescimento & desenvolvimento , Boratos/farmacologia , Candida/fisiologia , Candida albicans/efeitos dos fármacos , Candida albicans/fisiologia , Candida glabrata/efeitos dos fármacos , Candida glabrata/fisiologia , Contagem de Colônia Microbiana , Desinfetantes de Equipamento Odontológico/farmacologia , Humanos , Umidade , Teste de Materiais , Micologia/métodos , Método Simples-Cego , Hipoclorito de Sódio/farmacologia , Sulfatos/farmacologia , Propriedades de Superfície , Temperatura , Fatores de Tempo , MolhabilidadeRESUMO
PURPOSE: This study evaluated the cumulative effects of different microwave power levels on the physical properties of two poly(methylmethacrylate) (PMMA) denture base resins. MATERIALS AND METHODS: Eight sets of four PMMA specimens each (two polymerized in a water bath and two using microwave energy) were immersed in beakers containing 200 ml of distilled water. Each beaker was subjected to microwave irradiation for 3 minutes at a power level of 450,630, or 900 W. The surface roughness, surface hardness, linear stability, flexural strength, elastic modulus, impact strength, and fractographic properties were evaluated after either 6 or 36 simulated disinfection cycles. The data were statistically analyzed using ANOVA and the Tukey post hoc test (α= 0.05). RESULTS: The polymerization method did not influence any property (p > 0.05) except linear stability. The surface roughness (p < 0.001) and hardness (p= 0.011) increased after 36 irradiation cycles at 630 or 900 W. The resin polymerized using microwave energy exhibited greater linear distortion (p= 0.012), and there was a cumulative effect on linear stability for both resins (p < 0.001). No significant change (p > 0.05) was observed in flexural strength; however, the elastic modulus decreased (p= 0.008) after 36 disinfection cycles. The impact strength and crack propagation angles displayed no significant differences (p > 0.05). CONCLUSION: Within the limitations of this study, it can be concluded that microwave disinfection at 450 W to 630 W for 3 minutes is safe for PMMA.
Assuntos
Bases de Dentadura , Desinfecção/métodos , Micro-Ondas , Polimetil Metacrilato/efeitos da radiação , Análise do Estresse Dentário , Módulo de Elasticidade , Dureza , Teste de Materiais , Maleabilidade , Polimerização , Propriedades de SuperfícieRESUMO
OBJECTIVE: To evaluate the influence of hydrophilicity on the surface integrity of implants after insertion in low-density artificial bone and to determine the distribution of titanium (Ti) particles along the bone bed. METHODS: Forty-eight dental implants with different designs (Titamax Ex, Facility, Alvim, and Drive) and surface treatments (Neoporos® and Aqua™) were inserted into artificial bone blocks with density compatible with bone type III-IV. Hydrophobic Neoporos® surfaces were obtained by sandblasting and acid etching while hydrophilic Aqua™ surfaces were obtained by sandblasting, acid etching, and storage in an isotonic 0.9% NaCl solution. The surface integrity was evaluated by Scanning Electron Microscope (SEM) and the surface roughness parameters (Sa, Sp, Ssk, Sdr, Spk, Sk, and Svk) and surface area were measured with Laser Scanning Confocal Microscopy before and after installation. Bone beds were inspected with Digital Microscopy and micro X-Ray Fluorescence (µ-XRF) to analyze the metallic element distribution along the bone bed. RESULTS: Acqua™ implants had higher initial Sa and a pronounced reduction of Sa and Sp during insertion, compared to NeoPoros® implants. After insertion, Sa and Sp of Acqua™ and NeoPoros® implants equalized, differing only between designs of Acqua™ implants. Surface damage was observed after insertion, mainly in the apical region. Facility implants that are made of TiG5 released fewer debris particles, while the highest Ti intensity was detected in the cervical region of the Titamax Ex Acqua™ and Drive Acqua™ implants. SIGNIFICANCE: Physicochemical modifications to achieve surface hydrophilicity created a rougher surface that was more susceptible to surface alterations, resulting in more Ti particle release into the bone bed during surgical insertion. The higher Ti intensities detected in the cervical region of bone beds may be related to peri-implantitis and marginal bone resorption.
Assuntos
Implantação Dentária Endóssea , Implantes Dentários , Interações Hidrofóbicas e Hidrofílicas , Implantes Experimentais , Microscopia Eletrônica de Varredura , Osseointegração , Propriedades de Superfície , TitânioRESUMO
This study investigated the influence of implant macrogeometry and bone type on insertion torque (IT), primary stability (ISQ), surface topography damage, and the amount of titanium (Ti) released during insertion. Forty implants with different macrogeometries (Facility - Cylindrical with spiral-shaped threads; Alvim - Tapered with buttress-shaped threads) were inserted into artificial bone types I-II and III-IV. Surface morphology was evaluated by Scanning Electron Microscope (SEM) and roughness parameters with Laser Scanning Confocal Microscopy (LSCM) before and after insertion (AI). Implant macrogeometry was characterized by LSCM. The chemical composition of bone beds was determined by SEM associated with Energy Dispersive X-Ray Spectroscopy. The amount of Ti released was analyzed with Energy Dispersive X-Ray Fluorescence. Alvim had greater IT and ISQ than Facility. Bone types I-II require higher IT of implants. Alvim also had greater internal threads angle, higher initial roughness, and significant reduction of roughness AI, compared to Facility. The functional surface height reduced AI, especially in flank and valley of threads. Height of surface roughness of Alvim and Facility implants was similar AI. Implants surface morphology changes and metallic particles on bone beds were observed after implant insertion, mainly into bone types III-IV. Implants inserted into bone types I-II showed less surface damage. Alvim implants released more Ti (37.52 ± 25.03 ppm) than Facility (11.66 ± 28.55 ppm) on bone types III-IV. The implant macrogeometry and bone types affect IT, ISQ, surface damage, and Ti amount released during insertion. Alvim implants were more wear susceptible, releasing higher Ti concentration during insertion into bone types III-IV.
Assuntos
Implantes Dentários , Titânio , Osso e Ossos , Planejamento de Prótese Dentária , Osseointegração , Propriedades de Superfície , TorqueRESUMO
OBJECTIVES: New strategies for implant surface functionalization in the prevention of peri-implantitis while not compromising osseointegration are currently explored. The aim of this in vivo study was to assess the osseointegration of a titanium-silica composite implant, previously shown to enable controlled release of therapeutic concentrations of chlorhexidine, in the Göttingen mini-pig oral model. MATERIAL AND METHODS: Three implant groups were designed: macroporous titanium implants (Ti-Porous); macroporous titanium implants infiltrated with mesoporous silica (Ti-Porous + SiO2 ); and conventional titanium implants (Ti-control). Mandibular last premolar and first molar teeth were extracted bilaterally and implants were installed. After 1 month healing, the bone in contact with the implant and the bone regeneration in the peri-implant gap was evaluated histomorphometrically. RESULTS: Bone-to-implant contact and peri-implant bone volume for Ti-Porous versus Ti-Porous + SiO2 implants did not differ significantly, but were significantly higher in the Ti-Control group compared with Ti-Porous + SiO2 implants. Functionalization of titanium implants via infiltration of a SiO2 phase into the titanium macropores does not seem to inhibit implant osseointegration. Yet, the importance of the implant macro-design, in particular the screw thread design in a marginal gap implant surgery set-up, was emphasized by the outstanding results of the Ti-Control implant. CONCLUSIONS: Next-generation implants made of macroporous Ti infiltrated with mesoporous SiO2 do not seem to compromise the osseointegration process. Such implant functionalization may be promising for the prevention and treatment of peri-implantitis given the evidenced potential of mesoporous SiO2 for controlled drug release.
Assuntos
Próteses e Implantes , Animais , Antibacterianos , Implantes Dentários , Peri-Implantite/prevenção & controle , Dióxido de Silício , Propriedades de Superfície , Suínos , Porco Miniatura , TitânioRESUMO
OBJECTIVE: To evaluate, in vitro, the effect of two glucose concentrations (0.1 mM and 1.0 mM, simulating glucose concentration in saliva of healthy and diabetic individuals) on Candida albicans biofilm grown on epithelial monolayer. MATERIAL AND METHODS: C. albicans was inoculated on epithelial monolayers supplemented with 0.1 mM, 1.0 mM or no glucose. Control groups without C. albicans were also evaluated. Tissue response was assessed through the production of Interleukin-1α, Interleukin-8, Interleukin-6, Interleukin-10 and tumor necrosis factor-α. The complex of monolayer and biofilms were evaluated by quantitative reverse transcription polymerase chain reaction for expression of E-cadherin (CDH1), Caspase-3 (CASP3), ß-defensin-1 (DEFB-1) and ß-defensin-3 (DEFB-3). The biofilm architecture was visualized by confocal laser scanning microscopy. RESULTS: The production of Interleukin-1α and Interleukin-8 were increased in the presence of C. albicans (p < 0.05). Glucose did not interfere in the release of any cytokine evaluated. C. albicans downregulated transcripts for CDH1 (p < 0.05). Glucose did not induce a significant change in CDH1, CASP3, DEFB-1 and DEFB-3 messenger RNA expression. The biofilms were more structured in the presence of glucose, but no difference in the diffusion of hyphae through the epithelial cells were observed. CONCLUSIONS: The data suggest that glucose concentration does not affect the behavior of C. albicans during tissue invasion and other mechanisms must be related to the greater susceptibility of diabetic individuals to candidiasis.