A polyimine aerogel separator with electron cloud design to boost Li-ion transport for stable Li metal batteries.

The separator with high Young's modulus can avoid the danger of large-sized dendrites, but regulating the chemical behavior of lithium (Li) at the separator/anode interface can effectively eliminate the dendrite issue. Herein, a polyimine aerogel (PIA) with accurate nitrogen (N) functional design is used as the functional separator in Li metal batteries to promote uniform Li nucleation and suppress the dendrite growth. Specifically, the imine (N1) and protonated tertiary amine (N2) sites in the molecular structure of the PIA are significantly different in electron cloud density (ECD) distribution. The N1 site with higher ECD and the N2 site with lower ECD tend to attract and repulse Li+ through electrostatic interactions, respectively. This synergy effect of the PIA separator accelerates the interfacial Li+ diffusion on the Li anode to sustain a uniform two-dimensional Li nucleation behavior. Meanwhile, the well-defined nanochannels of the PIA separator show high affinity to electrolyte and bring uniform Li+ flux for Li plating/stripping. Consequently, the dendrites are effectively suppressed by the PIA separator in routine carbonate electrolyte, and the Li metal batteries with the PIA separator exhibit high Coulombic efficiency and stable high-rate cycling. These findings demonstrate that the ingenious marriage of special chemical structure designs and hierarchical pores can enable the separator to affect the interfacial Li nucleation behavior.

Microstructure-Reconfigured Graphene Oxide Aerogel Metamaterials for Ultrarobust Directional Sensing at Human-Machine Interfaces.

Graphene aerogels hold huge promise for the development of high-performance pressure sensors for future human-machine interfaces due to their ordered microstructure and conductive network. However, their application is hindered by the limited strain sensing range caused by the intrinsic stiffness of the porous microstructure. Herein, an anisotropic cross-linked chitosan and reduced graphene oxide (CCS-rGO) aerogel metamaterial is realized by reconfiguring the microstructure from a honeycomb to a buckling structure at the dedicated cross-section plane. The reconfigured CCS-rGO aerogel shows directional hyperelasticity with extraordinary durability (no obvious structural damage after 20 000 cycles at a directional compressive strain of ≤0.7). The CCS-rGO aerogel pressure sensor exhibits an ultrahigh sensitivity of 121.45 kPa-1, an unprecedented sensing range, and robust mechanical and electrical performance. The aerogel sensors are demonstrated to monitor human motions, control robotic hands, and even integrate into a flexible keyboard to play music, which opens a wide application potential in future human-machine interfaces.

Tree-Inspired Aerogel Comprising Nonoxidized Graphene Flakes and Cellulose as Solar Absorber for Efficient Water Generation.

As global freshwater shortages worsen, solar steam generation (SSG) emerges as a promising, eco-friendly, and cost-effective solution for water purification. However, widespread SSG implementation requires efficient photothermal materials and solar evaporators that integrate enhanced light-to-heat conversion, rapid water transportation, and optimal thermal management. This study investigates using nonoxidized graphene flakes (NOGF) with negligible defects as photothermal materials capable of absorbing over 98% of sunlight. By combining NOGF with cellulose nanofibers (CNF) through bidirectional freeze casting, we created a vertically and radially aligned solar evaporator. The hybrid aerogel exhibited exceptional solar absorption, efficient solar-to-thermal conversion, and improved surface wettability. Inspired by tree structures, our design ensures rapid water supply while minimizing heat loss. With low NOGF content (∼10.0%), the NOGF/CNF aerogel achieves a solar steam generation rate of 2.39 kg m-2 h-1 with an energy conversion efficiency of 93.7% under 1-sun illumination, promising applications in seawater desalination and wastewater purification.

Biomimetic Design of 3D Fe3O4/V-EVOH Fiber-Based Self-Floating Composite Aerogel to Enhance Solar Steam Generation Performance.

An interfacial solar steam generation evaporator for seawater desalination has attracted extensive interest in recent years. Nevertheless, challenges still remain in relatively low evaporation rate, unsatisfactory energy conversion efficiency, and salt accumulation. Herein, we have demonstrated a biomimetic bilayer composite aerogel consisting of bottom hydrophilic and vertically aligned EVOH channels and an upper hydrophobic conical Fe3O4 array. Thanks to the design merits, the 3D Fe3O4/V-EVOH evaporator exhibits a high evaporation rate of ∼2.446 kg m-2 h-1 and an impressive solar energy conversion efficiency of ∼165.5% under 1 sun illumination, which is superior to those of state-of-the-art evaporators reported so far. Moreover, the asymmetrical wettability not only allows the evaporator to self-float on the water but also facilitates the salt ion diffusion in the channels; thus, the evaporator shows no salt crystals on its surface and only a 6% decrease in evaporation performance even after the salt concentration increases from 0 to 10.0 wt %.

Strong, Lightweight, and Shape-Memory Bamboo-Derived All-Cellulose Aerogels for Versatile Scaffolds of Sustainable Multifunctional Materials.

Strong, lightweight, and shape-memory cellulose aerogels have great potential in multifunctional applications. However, achieving the integration of these features into a cellulose aerogel without harsh chemical modifications and the addition of mechanical enhancers remains challenging. In this study, a strong, lightweight, and water-stimulated shape-memory all-cellulose aerogel (ACA) is created using a combination strategy of partial dissolution and unidirectional freezing from bamboo. Benefiting from the firm architecture of cellulose microfibers bridging cellulose nanofibers /regenerated cellulose aggregated layers and the bonding of different cellulose crystal components (cellulose Iß and cellulose II), the ACA, with low density (60.74 mg cm-3 ), possesses high compressive modulus (radial section: 1.2 MPa, axial section: 0.96 MPa). Additionally, when stimulated with water, the ACA exhibits excellent shape-memory features, including highly reversible compression-resilience and instantaneous fold-expansion behaviors. As a versatile scaffold, ACA can be integrated with hydroxyapatite, carboxyl carbon nanotubes, and LiCl, respectively, via a simple impregnation method to yield functionalized cellulose composites for applications in thermal insulation, electromagnetic interference shielding, and piezoresistive sensors. This study provides inspiration and a reliable strategy for the elaborately structural design of functional cellulose aerogels endows application prospects in various multifunction opportunities.

Hydrosilylation Adducts to Produce Wide-Temperature Flexible Polysiloxane Aerogel under Ambient Temperature and Pressure Drying.

Despite incorporation of organic groups into silica-based aerogels to enhance their mechanical flexibility, the wide temperature reliability of the modified silicone aerogel is inevitably degraded. Therefore, facile synthesis of soft silicone aerogels with wide-temperature stability remains challenging. Herein, novel silicone aerogels containing a high content of Si are reported by using polydimethylvinylsiloxane (PDMVS), a hydrosilylation adduct with water-repellent groups, as a "flexible chain segment" embedded within the aerogel network. The poly(2-dimethoxymethylsilyl)ethylmethylvinylsiloxane (PDEMSEMVS) aerogel is fabricated through a cost-effective ambient temperature/pressure drying process. The optimized aerogel exhibits exceptional performance, such as ultra-low density (50 mg cm-3), wide-temperature mechanical flexibility, and super-hydrophobicity, in comparison to the previous polysiloxane aerogels. A significant reduction in the density of these aerogels is achieved while maintaining a high crosslinking density by synthesizing gel networks with well-defined macromolecules through hydrolytic polycondensation crosslinking of PDEMSEMVS. Notably, the pore/nanoparticle size of aerogels can be fine-tuned by optimizing the gel solvent type. The as-prepared silicone aerogels demonstrate selective absorption, efficient oil-water separation, and excellent thermal insulation properties, showing promising applications in oil/water separation and thermal protection.

Biomimetic Transparent Layered Tough Aerogels for Thermal Superinsulation and Triboelectric Nanogenerator.

Transparent aerogels are ideal candidates for thermally insulating windows, solar thermal receivers, electronics, etc. However, they are usually prepared via energy-consuming supercritical drying and show brittleness and low tensile strength, significantly restricting their practical applications. It remains a great challenge to prepare transparent aerogels with high tensile strength and toughness. Herein, biomimetic transparent tough cellulose nanofiber-based nanocomposite aerogels with a layered nanofibrous structure are achieved by vacuum-assisted self-assembly combined with ambient pressure drying. The nacre-like layered homogeneous nanoporous structures can reduce light scattering and effectively transfer stress and prevent stress concentration under external forces. The aerogels exhibit an attractive combination of excellent transparency and hydrophobicity, high compressive and tensile strengths, high toughness, excellent machinability, thermal superinsulation, and wide working temperature range (-196 to 230 °C). It is demonstrated that they can be used for superinsulating windows of buildings and high-efficient thermal management for electronics and human bodies. In addition, a prototype of transparent flexible aerogel-based triboelectric nanogenerator is developed. This work provides a promising pathway toward transparent tough porous materials for energy saving/harvesting, thermal management, electronics, sensors, etc.

Boosting Photocatalytic CO2 Methanation through Interface Fusion over CdS Quantum Dot Aerogels.

In the field of photocatalytic CO2 reduction, quantum dot (QD) assemblies have emerged as promising candidate photocatalysts due to their superior light absorption and better substrate adsorption. However, the poor contacts within QD assemblies lead to low interfacial charge transfer efficiency, making QD assemblies suffer from unsatisfactory photocatalytic performance. Herein, a novel approach is presented involving the construction of strongly interfacial fused CdS QD assemblies (CdS QD gel) for CO2 reduction. The novel CdS QD gel demonstrates outstanding photocatalytic performance for CO2 methanation, achieving a CH4 generation rate of ≈296 µmol g-1 h-1, with a selectivity surpassing 76% and an apparent quantum yield (AQY) of 1.4%. Further investigations reveal that the robust interfacial fusion in these CdS QDs not only boosts their ability to absorb visible light but also significantly promotes charge separation. The present work paves the way for utilizing QD gel photocatalysts in realizing efficient CO2 reduction and highlights the critical role of interfacial engineering in photocatalysts.

Spin Effect to Regulate the Electronic Structure of Ir─Fe Aerogels for Efficient Acidic Water Oxidation.

"Spin" has been recently reported as an important degree of electronic freedom to promote catalysis, yet how it influences electronic structure remains unexplored. This work reports the spin-induced orbital hybridization in Ir─Fe bimetallic aerogels, where the electronic structure of Ir sites is effectively regulated by tuning the spin property of Fe atoms. The spin-optimized electronic structure boosts oxygen evolution reaction (OER) electrocatalysis in acidic media, resulting in a largely improved catalytic performance with an overpotential of as low as 236 mV at 10 mA cm-2. Furthermore, the gelation kinetics for the aerogel synthesis is improved by an order of magnitude based on the introduction of a magnetic field. Density functional theory calculation reveals that the increased magnetic moment of Fe (3d orbital) changes the d-band structure (i.e., the d-band center and bandwidth) of Ir (5d orbital) via orbital hybridization, resulting in optimized binding of reaction intermediates. This strategy builds the bridge between the electron spin theory with the d-band theory and provides a new way for the design of high-performance electrocatalysts by using spin-induced orbital interaction.

Metal Halide Nanocrystals@Silica Aerogel Composite with Enhanced Dispersion Stability and Light Output for Efficient X-Ray Imaging in Harsh Environment.

Metal halide nanocrystals (MHNCs) embedded in a polymer matrix as flexible X-ray detector screens is an effective strategy with the advantages of low cost, facile preparation, and large area flexibility. However, MHNCs easily aggregate during preparation, recombination, under mechanical force, storage, or high operating temperature. Meanwhile, it shows an unmatched refractive index with polymer, resulting in low light yield. The related stability and properties of the device remain a huge unrevealed challenge. Herein, a composite screen (CZBM@AG-PS) by integrating MHNCs (Cs2ZnBr4: Mn2+ as an example) into silica aerogel (AG) and embedded in polystyrene (PS) is successfully developed. Further characterization points to the high porosity AG template that can effectively improve the dispersion of MHNCs in polymer detector screens, essentially decreasing nonradiative transition, Rayleigh scattering, and performance aging induced by aggregation in harsh environments. Furthermore, the higher light output and lower optical crosstalk are also achieved by a novel light propagation path based on the MHNCs/AG and AG/PS interfaces. Finally, the optimized CZBM@AG-PS screen shows much enhanced light yield, spatial resolution, and temperature stability. Significantly, the strategy is proven universal by the performance tests of other MHNCs embedded composite films for ultra-stable and efficient X-ray imaging.