Wrinkle-bioinspired silver nanowire surface enhanced Raman scattering sensors for pesticide molecule detection.

We demonstrate wrinkle-bioinspired flexible SERS sensor covered by silver nanowire (AgNWs) network for the detection of pesticide molecules. Compared with the silver film deposition substrates, the wrinkle-bioinspired AgNWs SERS substrates show stronger SERS effect, which were attributed to the electromagnetic field enhancement posed by the relatively high density "hot spots" of AgNWs. In order to investigate the adsorption performance of wrinkle-bioinspired flexible sensors, we measured the corresponding contact angles of AgNWs on the substrate surfaces before and after plasma treatment and found that the AgNWs treated with plasma are more hydrophilic than that without plasma treatment. Additionally, the wrinkle-bioinspired SERS sensors show different SERS activities under different tensile strain, and the 10-6 mol/L concentration of Rhodamine dye (R6G) molecules can be detected by portable Raman spectra, reducing greatly detection cost. The surface plasmon resonance of AgNWs is induced by adjusting the deformation of AgNWs substrate, enhancing the SERS signal. This reliability of wrinkle-bioinspired SERS sensors is further verified by in situ detection of pesticide molecules.

Multifunctional Thermally Conductive Composite Films Based on Fungal Tree-like Heterostructured Silver Nanowires@Boron Nitride Nanosheets and Aramid Nanofibers.

Thermal conduction for electronic equipment has grown in importance in light of the burgeoning of 5G communication. It is imperatively desired to design highly thermally conductive fillers and polymer composite films with prominent Joule heating characteristics and extensive mechanical properties. In this work, "solvothermal & in situ growth" method is carried out to prepare "Fungal tree"-like hetero-structured silver nanowires@boron nitride nanosheet (AgNWs@BNNS) thermally conductive fillers. The thermally conductive AgNWs@BNNS/ANF composite films are obtained by the method of "suction filtration self-assembly and hot-pressing". When the mass fraction of AgNWs@BNNS is 50 wt%, AgNWs@BNNS/ANF composite film presents the optimal thermal conductivity coefficient of 9.44 W/(m ⋅ K) and excellent tensile strength of 136.6 MPa, good temperature-voltage response characteristics, superior electrical stability and reliability, which promise a wide application potential in 5G electronic devices.

Highly stretchable and sensitive strain sensors based on modified PDMS and hybrid particles of AgNWs/graphene.

High-performance strain sensors have received extensive attention due to their wide range of applications in pulsebeat detection, speech recognition, motion detection, and blood pressure monitoring. However, it is difficult to simultaneously attain high sensitivity and excellent stretchability. In this work, a strain sensor based on modified polydimethylsiloxane (PDMS) and conductive hybrid particles of silver nanowires (AgNWs)/graphene was successfully fabricated. A facile solvothermal polymerization process was used to change the structure of cross-linking networks and to obtain the PDMS elastomer with excellent stretchability. The application of the modified PDMS endows the strain sensor with a large strain range (∼20%), which is 100% higher than that of the strain sensor with unmodified PDMS. The AgNWs/graphene hybrid particles were prepared by a simple coprecipitation, reduction, and drying method. AgNWs serve as bridges between graphene sheets, endowing the strain sensor with a large gauge factor (GF = 400). The stability of the strain sensor was also verified. Besides, the strain sensor was successfully used in fields such as finger bending and speech recognition. Considering its high sensitivity, excellent stretchability, and high working stability, the sensor has great potential in health monitoring and motion detection.

Low-temperature nanowelding silver nanowire hybrid flexible transparent conductive film for green light OLED devices.

Flexible organic light emitting diodes (OLED) have attracted great attention in many applications. MXene based flexible transparent conductive films (TCFs) are the most promising next-generation electrodes for flexible electronics. Herein, the sandwich conductive structure of silver nanowires (AgNWs) network, new 2D nanosheets with excellent conductivity, hydrophilicity and mechanical flexibility and PEDOT:PSS contributes to a highly transparent and conductive hybrid electrode through a simple, scalable, low-cost spray method. The Ti3C2Tx/AgNWs/PEDOT-PET film shows a low sheet resistance (<30 Ω/sq) and high transmittance (>80%) at 550 nm. Flexible OLED with such hybrid anode has the maximum brightness, current efficiency and current density, as high as 10 040 cd m-2, 3.7 cd A-1and 535.5 mA cm-2, respectively. These results indicate that the novel Ti3C2Tx/AgNWs/PEDOT-PET TCFs have a great potential for high-performance flexible optoelectronic devices.

Accelerated and outdoor weathering of silver nanowire transparent conductors under electrical stress in pseudo-modules.

In realistic applications, silver nanowires (AgNWs) are encapsulated in optoelectrical devices to function as transparent conductors and electrodes. Environmental stressors along with the essential electrical stress are inevitably harmful to the AgNWs inside the devices. Herein, to investigate the degradation behavior discrepancy between materials-level and device-level tests, we adopted pseudo-module to mimic the encapsulation. The pseudo-module allows the application of electrical stress and facilitates the interim specimen access for materials characterization through assembly-disassembly. Indoor accelerated and outdoor weathering tests with applied electrical stress to the pseudo-module encapsulated AgNW networks were performed. The impaired optoelectrical properties and morphological changes of AgNWs due to multiple or individual stressor(s) are investigated. Results indicate UVA exposure at elevated temperature coupled with electrical stress is responsible for the electrical failure of AgNW networks. Sulfidation that depresses optical transparency of AgNW networks is prone to occur at lower temperature. This work provides unambiguous degradation behaviors of AgNWs inside encapsulants, helping to improve the design of AgNWs related optoelectrical devices in the applications of solar irradiation environments.

Porous and nanowire-structured NiO/AgNWs composite electrodes for significantly-enhanced supercapacitive and electrochromic performances.

NiO/AgNWs composite films which specially contain both porous and one-dimensional (1D) nanowire structures are prepared uniformly via a simple chemical bath deposition method. The supercapacitive electrodes constructed by the as-prepared NiO/AgNWs composite films exhibit a high specific capacitance (980 F g-1at 1 A g-1), much higher than that of the pure NiO films. Particularly, a large optical modulation (84.3% at 550 nm) and short switching times for the coloration and bleaching (5.4 and 6.5 s) are also observed if these NiO/AgNWs films serve as the electrochromic materials. The superior capacitive and electrochromic properties of the NiO/AgNWs composite films are attributed to the large electrochemically effective surface areas and enhanced conductivity induced by the addition of 1D AgNWs, which efficiently shorten the ions/electrons diffusion paths and accelerate the reversible redox reactions. Therefore, the NiO/AgNWs composite films hold a great potential for applications as a novel electrode material in supercapacitive and electrochromic devices.

Ultralong AgNWs-induced toxicity in A549 cells and the important roles of ROS and autophagy.

Safety concerns have been raised with regard to silver nanowires (AgNWs) because of their extensive applications. Recently, ultralong AgNWs have shown physical properties superior to those of short AgNWs. However, little is known about their toxicity and potential risks. In this study, we demonstrated a series of ultralong AgNWs-induced biological effects in human lung cancer epithelial cells (A549). Ultralong AgNWs treatments induced ROS generation, mitochondria-mediated apoptosis, and self-protective autophagy at nonlethal concentrations. In contrast to some previous reports, apoptosis was found not to correlate with the reduction of intracellular ROS. Measuring the processing of ROS generation, apoptosis and autophagy, we demonstrated that ROS not only enhance mitochondrial damage, but also raise protective autophagic flux in ultralong AgNW-treated cells. Moreover, ultralong AgNWs were found to be internalized into the cytoplasm of the epithelial cells. This study not only investigates ultralong AgNWs-induced cytotoxicity but also pinpoints ROS as a key signal in mechanisms of their toxicity.

Impacts of sulfidation of silver nanowires on the degradation of bisphenol A in water.

Silver nanowires (AgNWs) are widely produced in many electronic and optical products, and could be inevitably discharged into the aquatic environments. Sulfidation is one of the most important transformation processes of AgNWs, and could significantly affect their fate and interactions with other pollutants in aquatic environment. In the present study, the sulfidation products of AgNWs with different atomic ratio of Ag and S were prepared under environmentally relevant conditions. The crystal structure, elemental composition, morphology and size of the sulfidation products were comprehensively characterized by powder X-ray diffraction, UV-vis spectroscopy, X-ray photoelectron spectroscopy and transmission electron microscope. The products were heterostructured nanowires and the Ag2S/Ag molar ratio increased with extension of the reaction time. The produced Ag2S-Ag nanowires displayed a good photocatalytic activity and facilitated the degradation of the copresent organic pollutant bisphenol A (BPA) under simulated sunlight irradiation. As sulfidation time increased, more Ag2S was generated and the Ag2S-Ag composites displayed high promotion effect on BPA degradation. This effect could be ascribed to the favorable synergistic effects between Ag2S and AgNWs, such as high electron-hole separation efficiency and low charge transfer resistance. The chemical scavenger experiments demonstrated that superoxide anion radicals and photogenerated holes in the sulfidation products of AgNWs could be the main reactive species for photocatalytic degradation.

Highly Conformable, Transparent Electrodes for Epidermal Electronics.

We present a highly conformable, stretchable, and transparent electrode for application in epidermal electronics based on polydimethylsiloxane (PDMS) and Ag nanowire (AgNW) networks. With the addition of a small amount of a commercially available nonionic surfactant, Triton X, PDMS became highly adhesive and mechanically compliant, key factors for the development of conformable and stretchable substrates. The polar functional groups present in Triton X interacted with the Pt catalyst present in the PDMS curing agent, thereby hindering the cross-linking reaction of PDMS and modulating the mechanical properties of the polymer. Due to the strong interactions that occur between the polar functional groups of Triton X and AgNWs, AgNWs were effectively embedded in the adhesive PDMS (a-PDMS) matrix, and the highly enhanced conformability, mechanical stretchability, and transparency of the a-PDMS matrix were maintained in the resulting AgNW-embedded a-PDMS matrix. Finally, wearable strain and electrocardiogram (ECG) sensors were fabricated from the AgNW-embedded a-PDMS. The a-PDMS-based strain and ECG sensors exhibited significantly improved sensing performances compared with those of the bare PDMS-based sensors because of the better stretchability and conformability to the skin of the former sensors.

Bio-Based Transparent Conductive Film Consisting of Polyethylene Furanoate and Silver Nanowires for Flexible Optoelectronic Devices.

Exploiting biomass has raised great interest as an alternative to the fossil resources for environmental protection. In this respect, polyethylene furanoate (PEF), one of the bio-based polyesters, thus reveals a great potential to replace the commonly used polyethylene terephthalate (PET) on account of its better mechanical, gas barrier, and thermal properties. Herein, a bio-based, flexible, conductive film is successfully developed by coupling a PEF plastic substrate with silver nanowires (Ag NWs). Besides the appealing advantage of renewable biomass, PEF also exhibits a good transparency around 90% in the visible wavelength range, and its constituent polar furan moiety is revealed to enable an intense interaction with Ag NWs to largely enhance the adhesion of Ag NWs grown above, as exemplified by the superior bending and peeling durability than the currently prevailing PET substrate. Finally, the efficiency of conductive PEF/Ag NWs film in fabricating efficient flexible organic thin-film transistor and organic photovoltaic (OPV) is demonstrated. The OPV device achieves a power conversion efficiency of 6.7%, which is superior to the device based on ITO/PEN device, manifesting the promising merit of the bio-based PEF for flexible electronic applications.

Deep Learning Enabled SERS Identification of Gaseous Molecules on Flexible Plasmonic MOF Nanowire Films.

Through the capture of a target molecule at the metal surface with a highly confined electromagnetic field induced by surface plasmon, surface enhanced Raman spectroscopy (SERS) emerges as a spectral analysis technology with high sensitivity. However, accurate SERS identification of a gaseous molecule with low density and high velocity is still a challenge due to its difficulty in capture. In this work, a flexible paper-based plasmonic metal-organic framework (MOF) film consisting of Ag nanowires@ZIF-8 (AgNWs@ZIF-8) is fabricated for SERS detection of gaseous molecules. Benefiting from its micronanopores generated by the nanowire network and ZIF-8 shell, the effective capture of the gaseous molecule is achieved, and its SERS spectrum is obtained in this paper-based flexible plasmonic MOF nanowire film. With optimal structure parameters, spectra of gaseous 4-aminothiophenol, 4-mercaptophenol, and dithiohydroquinone demonstrate that this film has good SERS performance, which could maintain obvious Raman signals within 30 days during reproducible detection. To realize SERS identification of gaseous molecules, deep learning is performed based on the SERS spectra of the mixed gaseous analyte obtained in this flexible porous film. The results point out that an artificial neural network algorithm could identify gaseous aldehydes (gaseous biomarker of colorectal cancer) in simulated exhaled breath with high accuracy at 93.7%. The integration of the flexible paper-based film sensors with deep learning offers a promising new approach for noninvasive colorectal cancer screening. Our work explores SERS applications in gaseous analyte detection and has broad potential in clinical medicine, food safety, environmental monitoring, etc.

Stretchable Electrodes with Interfacial Percolation Network.

Stretchable electrodes are an essential component that determines the functionality and reliability of stretchable electronics, but face the challenge of balancing conductivity and stretchability. This work proposes a new conducting concept called the interfacial percolation network (PN) that results in stretchable electrodes with high conductivity, large stretchability, and high stability. The interfacial PN is composed of a 2D silver nanowires (AgNWs) PN and a protruding 3D AgNWs PN embedded on the surface and in the near-surface region of an elastic polymer matrix, respectively. The protruded PN is obtained by changing the arrangements of AgNWs from horizontal to quasi-vertical through introducing foreign polymer domains in the near-surface region of the polymer matrix. The resulting electrode achieves a conductivity of 13 500 S cm-1 and a stretchability of 660%. Its resistance changes under stretched conditions are orders of magnitude lower than those of conventional 2D PN and 2D + 3D PN. An interfacial PN electrode made from liquid metal remained its conductivity at 46 750 S cm-1 after the electrode underwent multiple stretch-release cycles with a deformation of >600%. The concept of interfacial PN provides fruitful implications for the design of stretchable electronics.

A Sandwich Structural Filter Paper-AgNWs/MXene Composite for Superior Electromagnetic Interference Shielding.

A thin, lightweight and flexible electromagnetic interference (EMI) shielding paper composite is an urgent need for modern military confrontations. Herein, a sandwich-structured EMI shielding paper composite with an easy pavement consisting of a filter paper layer, middle AgNWs/MXene layer, and polyvinyl butyral (PVB) layer was constructed by vacuum-assisted filtration, spraying and air-drying. The middle AgNWs/MXene compound endowed the filter paper with excellent electrical conductivity (166 S cm-1) and the fabricated filter paper-AgNWs/MXene-PVB composite exhibits superior EMI shielding (30 dB) with a 141 µm thickness. Remarkably, the specific EMI shielding effectiveness (SSE/t) of the filter paper-AgNWs/MXene-PVB composite reached 13,000 dB cm2 g-1 within the X-band frequency range. This value represents one of the highest reported for cellulose-based EMI shielding materials. Therefore, our sandwich-structured filter paper composite with superior EMI shielding performance can be used in the medical and military fields.

Flexible Sandwich-Shaped Cellulose Nanocrystals/Silver Nanowires/MXene Films Exhibit Efficient Electromagnetic-Shielding Interference Performance.

The electromagnetic pollution problem is becoming increasingly serious due to the speedy advance of electronic communication devices. There are broad application prospects for the development of flexible, wearable composite films with high electromagnetic interference (EMI)-shielding performance. The MX@AC composite films were prepared from MXene, silver nanowires (AgNWs) and cellulose nanocrystals (CNCs) with a sandwich structure. Benefiting from the upper and lower frame structure formed by winding 1D AgNWs and CNC, the tensile strength of the MX@AC was improved to 35 MPa (12.5 wt% CNC content) from 4 MPa (0 wt% CNC content). The high conductivity of MXene and AgNWs resulted in the MX@AC composite film conductivity up to 90,670 S/m, EMI SE for 90 dB, as well as SSE/t up to 7797 dB cm2 g-1. And the MX@AC composite film was tested for practical application, showing that it can effectively isolate electromagnetic waves in practical application.

Thorough Optimization for Intrinsically Stretchable Organic Photovoltaics.

The development of intrinsically stretchable organic photovoltaics (is-OPVs) with a high efficiency is of significance for practical application. However, their efficiencies lag far behind those of rigid or even flexible counterparts. To address this issue, an advanced top-illuminated OPV is designed and fabricated, which is intrinsically stretchable and has a high performance, through systematic optimizations from material to device. First, the stretchability of the active layer is largely increased by adding a low-elastic-modulus elastomer of styrene-ethylene-propylene-styrene tri-block copolymer (SEPS). Second, the stretchability and conductivity of the opaque electrode are enhanced by a conductive polymer/metal (denoted as M-PH1000@Ag) composite electrode strategy. Third, the optical and electrical properties of a sliver nanowire transparent electrode are improved by a solvent vapor annealing strategy. High-performance is-OPVs are successfully fabricated with a top-illuminated structure, which provides a record-high efficiency of 16.23%. Additionally, by incorporating 5-10% elastomer, a balance between the efficiency and stretchability of the is-OPVs is achieved. This study provides valuable insights into material and device optimizations for high-efficiency is-OPVs, with a low-cost production and excellent stretchability, which indicates a high potential for future applications of OPVs.

Preparation and Performance of AgNWs/PDMS Film-Based Flexible Strain Sensor.

Flexible strain sensors are widely used in the fields of personal electronic equipment and health monitoring to promote the rapid development of modern social science and technology. In this paper, silver nanowires (AgNWs) prepared via the polyol reduction method were used to construct a flexible strain sensor. The AgNWs/PDMS film was obtained by transfer printing using AgNWs as a conductive layer and polydimethylsiloxane (PDMS) as a flexible substrate. The morphology of AgNWs was characterized by SEM and TEM. The aspect ratio of the AgNWs was more than 700. The strain sensitivity factor of the sensor was 2.8757, with a good linear relationship between the resistance and the strain. Moreover, the strain sensor showed good response results in human activity monitoring and the LED lamp response test, which provides a new idea for the construction of flexible wearable devices.

Synthesis and Deposition of Silver Nanowires on Porous Silicon as an Ultraviolet Light Photodetector.

The applications of silver nanowires (AgNWs) are clearly relevant to their purity and morphology. Therefore, the synthesis parameters should be precisely adjusted in order to obtain AgNWs with a high aspect ratio. Consequently, controlling the reaction time versus the reaction temperature of the AgNWs is crucial to synthesize AgNWs with a high crystallinity and is important in fabricating optoelectronic devices. In this work, we tracked the morphological alterations of AgNWs during the growth process in order to determine the optimal reaction time and temperature. Thus, here, the UV-Vis absorption spectra were used to investigate how the reaction time varies with the temperature. The reaction was conducted at five different temperatures, 140-180 °C. As a result, an equation was developed to describe the relationship between them and to calculate the reaction time at any given reaction temperature. It was observed that the average diameter of the NWs was temperature-dependent and had a minimum value of 23 nm at a reaction temperature of 150 °C. A significant purification technique was conducted for the final product at a reaction temperature of 150 °C with two different speeds in the centrifuge to remove the heavy and light by-products. Based on these qualities, a AgNWs-based porous Si (AgNWs/P-Si) device was fabricated, and current-time pulsing was achieved using an ultra-violet (UV) irradiation of a 375 nm wavelength at four bias voltages of 1 V, 2 V, 3 V, and 4 V. We obtained a high level of sensitivity and detectivity with the values of 2247.49% and 2.89 × 1012 Jones, respectively. The photocurrent increased from the µA range in the P-Si to the mA range in the AgNWs/P-Si photodetector due to the featured surface plasmon resonance of the AgNWs compared to the other metals.

Multifunctional Flexible AgNW/MXene/PDMS Composite Films for Efficient Electromagnetic Interference Shielding and Strain Sensing.

With the rapid development of electronic information technology, composite materials with outstanding performance in terms of electromagnetic interference (EMI) shielding and strain sensing are crucial for next-generation smart wearable electronic devices. However, the fabrication of flexible composite films with dual functionality remains a significant challenge. Herein, multifunctional flexible composite films with exciting EMI shielding and strain sensing properties were constructed using a facile vacuum-assisted filtration process and transfer method. The films consisted of ultrathin AgNW/MXene (Ti3C2Tx)/AgNW conductive networks (1 µm) attached to a flexible polydimethylsiloxane (PDMS) substrate. The obtained AgNW/MXene/PDMS composite film exhibited an exceptional EMI shielding effectiveness of 50.82 dB and good flexibility (retaining 93.67 and 90.18% of its original value after 1000 bending and stretching cycles, respectively), which are attributed to the enhanced multilayer internal reflection network created by the AgNWs and MXene as well as the synergistic effect of PDMS. Besides EMI shielding, the composite films also displayed remarkable strain sensing properties. They exhibited a wide linear range of tensile strain up to 68% with a gauge factor of 468. They also showed fast response, ultralow detection limit, and high mechanical stability. Interestingly, the composite films could also detect motion and voice recognition, demonstrating their potential as wearable sensors. This study highlights the effectiveness of multifunctional flexible AgNW/MXene/PDMS composite films in resisting electromagnetic radiation and monitoring human motion, thereby providing a promising solution for the development of flexible wearable electronic devices in complex electromagnetic environments.

Facile Transfer of Spray-Coated Ultrathin AgNWs Composite onto the Skin for Electrophysiological Sensors.

Disposable wearable sensors that ultrathin and conformable to the skin are of significant interest as affordable and easy-to-use devices for short-term recording. This study presents a facile and low-cost method for transferring spray-coated silver nanowire (AgNW) composite films onto human skin using glossy paper (GP) and liquid bandages (LB). Due to the moderately hydrophobic and rough surface of the GP, the ultrathin AgNWs composite film (~200 nm) was easily transferred onto human skin. The AgNW composite films conformally attached to the skin when applied with a LB, resulting in the stable and continuous recording of wearable electrophysiological signals, including electromyogram (EMG), electrocardiogram (ECG), and electrooculogram (EOG). The volatile LB, deposited on the skin via spray coating, promoted rapid adhesion of the transferred AgNW composite films, ensuring stability to the AgNWs in external environments. The AgNWs composite supported with the LB film exhibited high water vapor breathability (~28 gm-2h-1), which can avoid the accumulation of sweat at the skin-sensor interface. This approach facilitates the creation of rapid, low-cost, and disposable tattoo-like sensors that are practical for extended use.

Large-Scale Fabrication of Tunable Sandwich-Structured Silver Nanowires and Aramid Nanofiber Films for Exceptional Electromagnetic Interference (EMI) Shielding.

The recent advancements in communication technology have facilitated the widespread deployment of electronic communication equipment globally, resulting in the pervasive presence of electromagnetic pollution. Consequently, there is an urgent necessity to develop a thin, lightweight, efficient, and durable electromagnetic interference (EMI) shielding material capable of withstanding severe environmental conditions. In this paper, we propose an innovative and scalable method for preparing EMI shielding films with a tunable sandwich structure. The film possesses a nylon mesh (NM) backbone, with AgNWs serving as the shielding coating and aramid nanofibers (ANFs) acting as the cladding layer. The prepared film was thin and flexible, with a thickness of only 0.13 mm. AgNWs can easily form a conductive network structure, and when the minimum addition amount was 0.2 mg/cm2, the EMI SE value reached 28.7 dB, effectively shielding 99.884% of electromagnetic waves and thereby meeting the commercial shielding requirement of 20 dB. With an increase in dosage up to 1.0 mg/cm2, the EMI SE value further improved to reach 50.6 dB. The NAAANF film demonstrated remarkable robustness in the face of complex usage environments as a result of the outstanding thermal, acid, and alkali resistance properties of aramid fibers. Such a thin, efficient, and environmentally resistant EMI shielding film provided new ideas for the broad EMI shielding market.