Tension Side Fixation for Lapidus Arthrodesis: A Retrospective Analysis.

Moderate to severe hallux valgus deformity often requires a Lapidus procedure (first-tarsometatarsal arthrodesis). Traditional methods include a dorsal approach with dorsal or medial fixation. However, studies demonstrate plantar/tension-side fixation, provides superior load to failure and fixation strength. This could improve outcomes, address comorbidities, and accelerate postoperative protocols; however, a paucity exists for patient outcomes in the literature regarding tension-side-fixation. The purpose of this study is to report the outcomes for tension-side Lapidus fixation. A retrospective analysis was performed of 81 patients who underwent tension-side-fixation Lapidus. Data collection consisted of: time to weight-bear, time to return to regular shoegear, hardware removal rate, revision rate, recurrence rate, relative metatarsal shortening, and nonunion rates. Mean patient age was 44 years old (range: 16-82). There were 65 females, and 16 males. The average time to weightbearing was 10.4 days. Time to return to regular shoegear was a mean of 6 weeks (ranging 2-10 weeks). Hardware removal rate was 1.2%. The recurrence rate was 8.6% (7 of 81 patients) and 5 of those 7 patients experienced recurrence before frontal-plane-correction was adopted by the surgeon. The revision rate was 0% and despite 8.6% recurrence, no patients were dissatisfied or requested a revisional procedure. The first-metatarsal shortening was a mean of 0.42 mm. The complications were as follows: 7% superficial dehiscence, 1.2% superficial wound infection, 0% deep infection, and 1.2% asymptomatic nonunion. This study suggests tension-side-fixation for Lapidus arthrodesis may allow for safe early return to weightbearing, early return to regular shoegear, low hardware removal rate, low revision rate, low metatarsal shortening, and low nonunion rate.

Retrospective Comparison of Preoperative and Postoperative Foot Width in Minimally Invasive Hallux Valgus Surgery.

Minimally invasive surgery (MIS) has gained popularity for hallux valgus correction in the adult population. The advantage of reproducibility of this procedure can aid in lower operating room costs, quicker recovery, and fewer complications. The purpose of this retrospective study was to compare preoperative versus postoperative foot widths in patients that underwent MIS hallux valgus correction. The average preoperative foot width was 101.1 ± 5.67 mm and postoperatively the foot width measured at 12-month follow-up was 95.9 ± 4.92 mm, which was statistically significant (p < .001). Overall, there was a 5.03 ± 3.71% reduction in foot width, with a statistically significant linear relationship between preoperative foot width and percent change in width following the procedure (R = -0.46; p = .003). Based on our results, we can conclude that MIS bunion surgery can effectively narrow the foot postoperatively, particularly in patients with a wider forefoot, adding cosmetic benefit to the procedure.

What Do Patients Report Regarding Their Real-World Function Following Concurrent Arthrodesis of the First Tarsometatarsal and First Metatarsophalangeal Joints.

First metatarsal phalangeal joint and the first Tarsometatarsal arthrodesis have both been used for deformity correction and treatment of pain and arthritis. Concomitant arthrodesis of the first metatarsophalangeal and first tarsometatarsal joints (Double First Ray Arthrodesis) has rarely been described. We surveyed 29 patients who underwent double first-ray arthrodesis for primary or revision correction of hallux valgus. A custom questionnaire was used to assess their activities of daily living and sports activity at a mean follow-up of 19.6 months (median 18.4 months). Secondary endpoints were return to activity, deformity correction, and arthrodesis healing rate. The primary outcomes showed an excellent return to activities of daily living with 96.6% of patients capable of walking as much as they liked after surgery at a normal pace. About 96.6% reported they felt that their surgery was successful, they had no pain, and the loss of motion at the joint fusion sites did not affect their ability to perform daily activities. Protected walking in a fracture boot was initiated at a mean (SD) of 9.8 (9.9) days. Return to an athletic shoe occurred at a mean (SD) of 44.2 (11.7) days. Full unrestricted activity was at a mean (SD) of 105.2 (19.3) days with 65% of the patient group reporting that their recovery was easier than expected. There was 1 nonunion and no other complications. This data set supports the hypothesis that patients undergoing double first-ray arthrodesis can return to activities of daily living and sports with and low complication rate.

The Triplanar Hallux Abducto Valgus Classification System: Is it Valid?

Historically, 2-dimensional radiographic study techniques have been used to classify deformity and guide treatment of hallux valgus deformities in the transverse plane. Recently, a triplanar hallux abducto valgus classification system was proposed. The key elements of this classification system are the pathologic alignments in 3 anatomic planes. The triplanar hallux abducto valgus classification system is intended to clarify the deformity and apply a triplanar anatomic algorithm for treatment. To our knowledge, this classification system has not been validated. Our objective was to assess reliability of the triplanar hallux valgus classification system. Patients with hallux abducto valgus were identified from a foot and ankle registry. Digital radiographs were assembled in a digital slide presentation. The eligibility criteria required complete radiographic studies and represented varying degrees of hallux abducto valgus. The reviewers included 3 board-certified, fellowship-trained orthopedic foot and ankle surgeons. Each reviewer independently classified the hallux abducto valgus deformity for a total of 75 observations. After an 8-week washout period, the order of the hallux abducto valgus cases was randomized in the digital slide presentation and redistributed to the reviewers. The average kappa value from 3 readers was 0.241 with 95% CI (0.093-0.374), indicating a fair agreement. The inter-reader agreement was 0.046 with 95% CI (-0.041 to 0.112), showing poor agreement between readers. Our results indicate the triplanar hallux abducto valgus is not a reliable classification system. While this is the first known triplanar hallux abducto valgus classification system, it lacks prognostic value and reliability.

Immediate Weightbearing Following First Metatarsal Phalangeal Joint Arthrodesis With 2 Nickel Titanium Alloy Staples.

The use of staples has been shown to be a reasonable fixation technique to achieve stability of a first MTPJ arthrodesis. Although it has been shown to be a weaker construct than crossed screws or plate and screw combinations, their ease of insertion, low profile, and stability make them a desirable choice for first MTPJ arthrodesis fixation. However, because of this relative weakness, the question remains whether immediate weightbearing when using staples is advisable. The aim of this study is to determine whether the use of 2 nickel-titanium alloy (NITINOL) staples, placed at 90 degrees to one another is a stable enough construct to support full, immediate weightbearing following first MTPJ arthrodesis. We performed a retrospective chart review of patients undergoing first MTPJ arthrodesis by a single surgeon utilizing 2 NITINOL staples placed at 90 degrees to one another. Patients were allowed to be fully weightbearing immediately postoperatively. Forty-seven of 50 (94%) patients achieved complete radiologic consolidation of fusion at 12 weeks, with only 3 requiring revision surgery for nonunion. All of the patients requiring revision surgery for nonunion, had preoperative diagnosis of hallux abducto valgus. We concluded that the use of 2 NITINOL staples placed at 90 degrees to one another is a viable option for first MTPJ arthrodesis, and immediate weightbearing does not increase rate of nonunion or incidence of revision surgery when compared to other fixation techniques.

Radiological Analysis of the Syndesmosis Concept in Metatarsus Primus Varus and Hallux Valgus Deformities Recurrence Prevention.

Hallux valgus (HV) is a common deformity of the foot. Its postoperative recurrence is not uncommon and is closely related to the recurrence of its underlying metatarsus primus varus (MPV) deformity. The syndesmosis procedure uses 1 to 2 intermetatarsal cerclage sutures to realign the first metatarsal and then induces a biological bonding between the 2 metatarsals to prevent the MPV deformity from recurring. This radiological study aimed to assess its effectiveness in long-term MPV and HV deformities recurrence prevention. Ninety-two feet of 51 consecutive patients had syndesmosis procedures that were prospectively followed up for more than 1 y and up to 14 y, averaging 100.5 (SD 45.2) months. Patients underwent X-ray examinations regularly at fixed intervals of their feet. We used Hardy's methods in measuring the intermetatarsal angle (IMA), hallux valgus angle (HVA), and medial sesamoid position from standing foot X-rays. More than 450 relevant X-ray and photo images were submitted as Supplementary Material for online viewing and reference. There was a significant final correction of IMA from 14.30° (SD 2.70) to 6.70° (SD 1.75) (p < .0001). There was no significant increase in IMA after the sixth postoperative month to their final follow-up endpoints, regardless of their lengths. There was a significant final correction of HVA from 31.95° (SD 7.45) to 19.1° (SD 7.45) (p < .0001). This study reconfirmed past findings that the MPV deformity could be corrected without osteotomies. Creating a syndesmosis-like intermetatarsal bonding was effective for long-term MPV recurrence prevention. Three feet had postoperative stress fracture of the second metatarsal. However, the HV deformity correction was less satisfactory, and the reasons were explained.

Combined Distal Metatarsal and Akin Osteotomies for Concomitant Metatarsophalangeal and Interphalangeal Hallux Valgus: Clinical and Radiological Outcomes.

Combined metatarsal and Akin-type proximal phalanx osteotomies represent a surgical solution for concomitant metatarso-phalangeal and inter-phalangeal hallux valgus. This retrospective observational study aimed to evaluate clinical and radiographic outcomes following combined distal linear metatarsal and Akin osteotomies. The study included 42 feet from 37 patients, with a mean follow-up of 27.1 (range 24-37) months. Mean surgical time was 16.54 ± 4.17 minutes. Pre- and postoperative clinical scores and radiological parameters were collected. Positive outcomes with a low recurrence and complications rates were reported. A statistically significant improvement in the Manchester-Oxford foot questionnaire, the EuroQol 5D-5L dimensions instrument, the visual analogue scale, the intermetatarsal angle, the hallux valgus angle, the distal metatarsal articular angle, and the interphalangeal angle correction was observed. Despite the results reported, further prospective studies are needed to identify the most suitable patients for this combined osteotomy approach.

Cannulated screws versus nitinol staple for tarsometatarsal fusion: A cadaveric biomechanical comparison model.

BACKGROUND: The objective of this study was to evaluate the biomechanical stability of a medially placed nitinol staple compared to two crossed-screws in the first TMT-1 joint fusion in a cadaveric cyclic loading model. METHODS: Seven matched pairs (N = 7) of lower limb cadaveric specimens were utilized. TMT-1 joints from each donor were fixed with a medially placed nitinol staple or dorsally placed two 3.5 mm partially threaded cannulated crossed-screws. Specimens were tested in a 4-point bending setting with increasing cyclic forces. RESULTS: The mean plantar gapping was not significantly different between the two groups at any loading stage below 200 N. Specimens fixed with a nitinol staple failed at a mean load of 305 ± 57 N. Conversely, those fixed with crossed-screws failed at 373 ± 86 N. (P = .09). CONCLUSION: There was no statistical difference between a medially placed nitinol staple and dorsally placed crossed-screws in failure loads and plantar gapping under cyclic loads at the TMT-1 joint, however, the staple fixation was much more variable. LEVEL OF EVIDENCE: Level V, basic science study, biomechanics.

Learning curve in relation to radiation exposure, procedure duration and complications rate for Minimally Invasive Chevron Akin (MICA) osteotomy.

BACKGROUND: Minimally invasive chevron Akin osteotomy (MICA) has become increasingly common and is compatible with the traditional open approaches for hallux valgus correction. However, it is impeded by concerns regarding the steep learning curve, increased radiation exposure and some specific complications. No standardized method for identifying a learning curve exists. We used a reproducible mathematical model to accurately define the learning curve of MICA with a focus on fluoroscopy time, procedure duration and complications rate. METHODS: We conducted a retrospective study of MICA procedure performed by a single surgeon during his initial experience with this procedure. The chronologic case number was plotted against variables of interest and learning was identified as the point at which instantaneous rate of change of a curve fit to the data set equalled the average rate of change of the data set. RESULTS: One hundred cases have been analysed. Learning plateau in operation time was achieved after 29 cases, with the first 29 cases requiring a median of 60 min compared to 40 min for the latter 71 cases. Proficiency in fluoroscopy application occurred in case 30. The median fluoroscopy time for the first 30 cases was 86 seconds compared to 70 seconds in another 70 cases. The complication rate plateau was reached after 42 cases, with 15 of 22 complications occurring in the group operated first. CONCLUSION: Results demonstrate surgeon's comfort with MICA to minimize operative time and radiation exposure after 30 cases. The plateau is achieved later for complications. Findings impose lag between surgeon feeling comfortable with procedure and a decrease in complications. Further research is reasonable to analyse several surgeons learning curve and to generate a potential reference learning curve that could serve as a normative. TRIAL REGISTRATION: UKC-MB-KME-33/19, retrospectively registered.

Interreader reliability assessment of hallux valgus evaluation on dorsoplantar weightbearing radiographs from a prospective multi-center trial and correlation with patient-reported outcome measures.

OBJECTIVE: To determine inter-reader reliability (IRR) of hallux valgus (HV) related parameters, i.e. intermetatarsal angle (IMA), hallux valgus angle (HVA), lateral round sign of the first metatarsal, tibial sesamoid position (TSP), metatarsus adductus angle (MAA), transverse osseous foot width, 1st MT length, MTP osteoarthritis (OA), and distal metatarsal articular angle (DMAA). These were correlated with patient-reported outcome measures (PROMs). MATERIALS AND METHODS: A prospective single-arm Level 3 multicenter clinical trial in which standardized radiographs and PROMs were collected at the time of the initial patient visit for pre-operative assessment. Two musculoskeletal radiologists performed measurements blinded to each other's reads and clinical information. Intraclass coefficient and kappa were obtained for inter-reader analysis. A partial spearman rank order was used to correlate the measurements with PROMs. RESULTS: The final cohort size of 183 patients had mean age of 40.77 years, mean body mass index was 26.11 kg/m2, with 91.2% females and 8.7% males. There was excellent IRR for HVA (0.96, CI: [0.94,0.97]), IMA (0.92, CI: [0.89,0.94]), transverse osseous foot width (0.99, CI: [0.98,1.00]), and DMAA (0.80, CI: [0.74, 0.85]), good agreement for TSP (0.73, CI:[0.67,0.79]) and MAA (0.67, CI: [0.16, 0.84]), fair agreement for MTP OA (0.48, CI: [0.36,0.59]), and poor agreement for lateral round sign (0.32, CI: [0.11, 0.52]. The negative correlation of increasing transverse osseous foot width with worsening PROMIS physical but better MOxFQ and VAS scores is likely spurious. CONCLUSION: Good to excellent inter-reader reliability was observed for the most often used measurements for HV assessment without major trends in their correlations with PROMs. Lateral round sign is not a reliable finding in HV deformity.

The distal metatarsal screw is not always necessary in third-generation MICA: a case-control study.

INTRODUCTION: To evaluate the clinical and radiological results after fixation of the first metatarsal head (MTH) with one or two screws as part of the third-generation minimally invasive Chevron-Akin osteotomy (MICA) for hallux valgus deformities. MATERIALS AND METHODS: Between August 2020 and November 2021, 55 MICA procedures (50 patients, male:female = 7:43), 22 with two (MICA2), 33 with one screw (MICA1) were performed for mild to severe hallux valgus deformities. Exclusion criteria were a concomitant pes adductus (Sgarlato angle > 20°) or hindfoot/midfoot deformities requiring treatment. In 27 cases, additional procedures on the forefoot (small toe corrections or metatarsal osteotomies II-V) were necessary. Pre- and post-operatively, hallux valgus angle (HVA) and intermetatarsal I/II angle (IMA) were measured. Clinically, subjective satisfaction, range of motion (ROM) of the first metatarsophalangeal joint (MTPJ), and pain level (NRS score) were evaluated. The minimum follow-up was 12 months. RESULTS: Displacement of MTH was 70-90% on average, all osteotomies showed full consolidation at latest follow-up. In one case of either group, a slight subsidence of MTH was documented. The radiological and clinical parameters showed no differences between the groups. The pain level improved by an average of three points. The mobility of the MTPJ showed a slight reduction in nine cases after three months (4 MICA2, 5 MICA1) which persisted in three cases. Fifty-two of 55 patients (95%) would opt again for the operation. CONCLUSIONS: Fixation of the first MTH with a single bicortical screw in MICA with moderate lateralization of MTH shows stable anchoring and good clinical results. The routine use of a second metatarsal screw can be omitted.

Surgical management of clubfoot overcorrection: a case series.

INTRODUCTION: Overcorrection is a possible complication of clubfoot treatment, whose prevalence varies from 5 to 67%. Overcorrected clubfoot usually presented as a complex flatfoot with different degrees of hindfoot valgus, flat top talus, dorsal bunion, and dorsal navicular subluxation. The management of clubfoot overcorrection is challenging, and both conservative and surgical treatments are available. This study aims to present our experience in the surgical management of overcorrected clubfoot and to provide an overview of actual treatment options for each specific sub-deformity. MATERIALS AND METHODS: A retrospective cohort study of patients surgically treated for an overcorrected clubfoot from 2000 to 2015 at our Institution was conducted. Surgical procedures were tailored to the type and symptomatology of the deformity. A medializing calcaneal osteotomy or subtalar arthrodesis was performed for hindfoot valgus. Subtalar and/or midtarsal arthrodesis were considered in cases of dorsal navicular subluxation. The first metatarsus elevatus was addressed through a proximal plantarflexing osteotomy, sometimes associated with a tibialis anterior tendon transfer. Clinical scores and radiographic parameters were obtained pre-operatively and at the last follow-up. RESULTS: Fifteen consecutive patients were enrolled. The series included 4 females and 11 males, with a mean age at surgery of 33,1 (18-56) years, and a mean follow-up of 4,46 (2-10) years. Seven medializing calcaneal osteotomies, 5 subtalar arthrodesis, 11 first metatarsal plantarflexing osteotomies, and 7 anterior tibialis tendon transfers were performed. A statistically significant improvement in both clinical and radiographic scores was observed. CONCLUSIONS: Management of overcorrected clubfoot involves many surgical techniques because of the high interpersonal variability of the deformities. The surgical approach showed positive results, as long as the indication is based on clinical symptoms and functional impairment rather than morphological alterations and radiographic findings.

Incidence of Nonunion Following First Metatarsophalangeal Joint Arthrodesis for Hallux Valgus Deformity: A Retrospective Analysis of Four Different Constructs.

Arthrodesis of the great toe joint is a valuable procedure for hallux valgus deformities. The primary aim of this study was to determine nonunion rates of a first metatarsophalangeal joint (MTPJ) arthrodesis for bunion deformity. This was a retrospective review of 166 consecutive limbs that underwent a first metatarsal phalangeal joint arthrodesis at Wake Forest Baptist Medical Center (WFBMC). Procedures were performed using 4 different constructs for the arthrodesis. Incidence of nonunion, intermetatarsal correction, infection, and recurrence were measured. Overall, 20 patients (12%) experienced nonunion following a first metatarsophalangeal joint arthrodesis. Eighty-seven patients (86%) of plate and screw patients achieved union while 14 (78%) of crossing screw patients achieved union. The minimum time of follow-up was 3 months and the maximum time was 15.4 months. The mean change in intermetatarsal and hallux valgus angle correction was 3.4° and 20.3°, with no statistical difference based on hardware construct or being diabetic. First metatarsophalangeal joint arthrodesis is a viable option for hallux valgus. However, the results of the present study suggest that there is a lower fusion rate of the first MTPJ using crossing screws for bunion deformities.

Correlation Analysis Between Clinical Hypermobility Measurement and Radiographic Parameters of the Hallux Valgus Deformity.

The finding of "hypermobility" has conventionally been considered as a dichotomous categorical variable in both clinical practice and in the literature. In other words, it is defined as being either "present" or "absent" in patients with hallux valgus. Yet it might be far more likely that this represents a continuous variable described by a bell-shaped distribution. Therefore the objective of this investigation was to consider hypermobility as a continuous variable, and to compare the sagittal plane first ray motion to radiographic parameters commonly used in the evaluation of the hallux valgus deformity by means of correlation analyses. The radiographs and measurements of 86 feet were included and measurement of sagittal plane first ray motion was performed with the validated Klaue device. No statistically significant correlation was observed between the total first ray motion with the first intermetatarsal angle (Pearson correlation coefficient 0.106; p = .333), hallux valgus angle (Pearson correlation coefficient -0.106; p = .330), nor sesamoid position (Pearson correlation coefficient 0.155; p = .157). The results of this investigation uniquely consider measurement of hypermobility as a continuous variable, and find no correlation between first ray sagittal plane motion and radiographic parameters associated with the hallux valgus deformity. These results might indicate that although the concept of hypermobility has traditionally been coupled with presentation of the hallux valgus deformity, this might simply represent the result of a historical confirmation bias.

Maintenance of Correction of the Modified Lapidus Procedure With a First Metatarsal to Second Metatarsal Screw With "Spot Weld" Technique: A Retrospective and Radiographic Analysis.

Lapidus first tarsometatarsal (TMT) arthrodesis gained popularity for its ability to correct large deformities especially in cases of medial column instability. Despite solid first TMT fusion, instability between the first and second columns can result in loss of intermetatarsal (IM) angle correction over time. A "spot weld" or fusion between the first and second metatarsal may improve maintenance of correction. This retrospective study reviewed cases of Lapidus arthrodesis with first to second metatarsal base screw fixation for maintenance of IM correction and determine whether a "spot weld" is predictive of maintenance. A total of 90 cases (77 patients) performed by a single surgeon met inclusion with average follow-up of 309 days. First TMT fusion occurred in 87/90 (96.7%) cases with 76 dorsal plate, 10 dorsal staple, and 4 all screws. No incidence of complications related to the 1-2 screw was noted. Mean preoperative IM 1-2 angle 14.90°, mean correction to 6.22° post-operative and final maintained correction at 7.10°, mean loss of correction 0.87°. There were "spot welds" in 65/90 (72.2%) with mean loss of 0.48° versus loss of 1.88° in "no spot weld" subgroup (p < .001). Cases with no spot weld and screw lucency lost 2.25° (p < .001). Loss of IM 1-2 correction can occur due to first and second ray intra-column instability even in cases of solid first TMT arthrodesis. Incorporating a completed "spot weld" with bone grafting and first to second metatarsal screw was found to maintain correction with minimal loss (0.87°).

Are Radiographs Associated With Patient Satisfaction After Scarf Bunionectomy?

There are over 350,000 bunion surgeries performed in the USA annually, making it one of the most common elective forefoot surgeries. Studies have suggested that as many as 10% of patients remain dissatisfied after bunion surgery. The purpose of this study is to evaluate if radiographic variables are associated with patient satisfaction at 1 year postoperatively. We performed a secondary analysis of prospectively collected data on 69 consecutive adult patients (mean age 45 ± 14 years, 91% female [63/69]) who underwent isolated hallux valgus surgery from January 2016 to January 2017. Subjects completed a standardized 4-item survey inquiring about their satisfaction with regards to pain relief, overall operative result, cosmetic appearance, and ability to wear desired shoe gear. Conventional radiographic indices for hallux valgus were examined preoperatively and 3 months postoperatively. An association model using backward stepwise logistic regression was utilized to determine which variables, if any, are most important in explaining patient satisfaction after surgery. Sixty-nine subjects completed the 4-item satisfaction survey with 53.6% (37/69) of subjects answering they were fully satisfied on all aspects of the survey at 12 months postoperatively. In the final regression model, no radiographic or demographic variables were associated with patient satisfaction including shoe gear, cosmetic appearance, pain relief, and overall operative result. Radiographic variables did not appear to be associated with patient satisfaction at one year postoperatively in our study. Factors such as quality of life, anxiety levels, fear of surgery, and/or preoperative expectations may offer more insight into satisfaction; however, further research should be performed to examine this further.

The Learning Curve of Third-Generation Percutaneous Chevron and Akin Osteotomy (PECA) for Hallux Valgus.

The learning curve to reach technical proficiency for third-generation percutaneous or minimally invasive chevron and Akin osteotomies (PECA/MICA) is recognized to be steep however it is poorly defined in the literature. This study is a retrospective review of the first 58 consecutive PECA cases of a single surgeon. The primary outcome was the number of cases required to reach technical proficiency as defined by the operation time. Secondary outcomes included radiation exposure, radiographic deformity correction, and complication rates. Between November 2017 and March 2019, 61 consecutive PECA cases were performed with outcome data available for 58 of these (95%). Technical proficiency was reached after 38 cases. Operation time and radiation exposure significantly decreased after this transition point (p < .05). There was no difference in complication rate or radiographic deformity correction regardless of position along the learning curve (p > .05). In conclusion, the mean number of cases required to reach technical proficiency in third-generation PECA is 38 cases. The complication rate does not correlate to the number of cases performed, therefore surgeons interested in learning minimally invasive surgery can be reassured that there is unlikely to be an additional risk of harm to a patient during the learning curve.

Radiographic Assessment of Relationship Between Medial Cuneiform Obliquity and Hallux Valgus.

The research results are inconsistent that assessing whether the increased obliquity of the distal articular surface of the medial cuneiform leads to an increase in hallux valgus angle. Thus, this study investigated the relationship between distal medial cuneiform obliquity and hallux valgus by measuring various angles in weightbearing anteroposterior radiographs of the foot. In total, 679 feet of 538 patients with the radiographs were included in the study. We measured radiographic parameters including hallux valgus angle, first to second intermetatarsal angle, metatarsus adductus angle, first metatarsus cuneiform angle, distal medial cuneiform angle, and first proximal metatarsal articular angle. The surface morphology (flat or curved) of the first tarsometatarsal joint was also recorded. Our results analysis revealed a weak negative correlation between distal medial cuneiform angle and both hallux valgus angle and first to second intermetatarsal angle, contrary to our assumption. So we believe that distal medial cuneiform angle was relatively constant and it cannot be used as a characteristic angle for quantifying hallux valgus. First metatarsus cuneiform angle was a characteristic indicator of hallux valgus and was positively correlated with its severity (p < .000), indicating that it can be used to measure the size of hallux valgus. It can also be used as a reference factor for the first metatarsal osteotomy in clinical bunion orthopedics. First tarsometatarsal joint morphology was unrelated to hallux valgus, whereas metatarsus adductus angle, and first proximal metatarsal articular angle should be considered in hallux valgus.

The Incidence of Complications Following Scarf Osteotomy for the Treatment of Hallux Valgus: A Systematic Review With Meta-Analysis.

The Scarf osteotomy is a surgical procedure performed to correct a hallux valgus deformity. Multiple studies have supported use of the procedure with favorable outcomes. In contrast, there have been studies showing a significant complication rate with the procedure. Incidence of complications remains underreported in the literature. We performed a systemic review and meta-analysis examining a wide range of reported complications and associated clinical outcomes from the Scarf osteotomy. One hundred and sixteen publications were identified and 25 (21.6%) met our inclusion criteria. A total of 1583 Scarf procedures were included. Weighted mean follow-up was 26.4 months [range 12-168 months]. We found a 5.1% rate of recurrence, 3.5% rate of troughing, 1.0% rate of avascular necrosis, 1.8% rate of nonunion, 2.7% rate of malunion, 2.4% rate of infection, 5.3% rate of complex regional pain syndrome, and 3.4% rate of hallux varus. An average decrease in intermetatarsal angle of 6.3° was observed. No statistical difference was found in outcomes when comparing Scarf versus Scarf with additional procedure performed at time of surgery. To our knowledge, this systematic review and meta-analysis contains the highest number of Scarf procedures analyzed and presents complication rates on multiple adverse outcomes.

Hemiepiphysiodesis for juvenile hallux valgus deformity: A systematic review.

BACKGROUND: Among the numerous surgical interventions for correcting hallux valgus deformity in skeletally immature patients, hemiepiphysiodesis is a simple technique with a low complication rate yet its effectiveness remains unclear. This systematic review evaluates hemiepiphysiodesis of the first metatarsal for treating juvenile hallux valgus (JHV) deformities with respect to radiological outcomes, postoperative clinical outcomes, and postoperative complications. METHODS: EMBASE, MEDLINE, PubMed, Cochrane Central Register of Controlled Trials (CENTRAL), and Cumulative Index to Nursing and Allied Health Literature (CINAHL) database were searched from inception to September 15th, 2022, for studies investigating hemiepephysiodesis for JHV and its effect on clinical and radiological outcomes. The search, data extraction and methodologic assessment were performed in duplicate for all included studies. RESULTS: Six studies out of 488 with a total of 147 feet in 85 patients were included in the final qualitative synthesis. The American Orthopaedic Foot & Ankle Society hallux metatarsophalangeal interphalangeal scale (AOFAS Hallux MTP-IP scale) was used in two studies. The mean pooled preoperative score was 62.2 ± 8.9 and improved to 88.6 ± 4.8 postoperatively in 33 patients. All six studies reported significant improvement in the hallux valgus angle (HVA) from mean preoperative angle of 29.2° ± 3.7-23.8° ± 4.5° postoperatively, while the intermetatarsal angle (IMA) preoperative and postoperative means corrected from 13.9° ± 1.1-11.4° ± 1.2°, respectively. Out of 147 feet, 21 (14.2%) had reported complications including recurrence and need for revision surgery. CONCLUSION: This systematic review confirms that hemiepiphysiodesis of the first metatarsal in patients with JHV has improved clinical and radiological outcomes. LEVEL OF EVIDENCE: Level IV, Systematic review.