Brown Coal and Logwood Combustion in a Modern Heating Appliance: The Impact of Combustion Quality and Fuel on Organic Aerosol Composition.

Residential heating with solid fuels is one of the major drivers for poor air quality in Central and Eastern Europe, and coal is still one of the major fuels in countries, such as Poland, the Czech Republic, and Hungary. In this work, emissions from a single-room heater fueled with brown coal briquettes (BCBs) and spruce logs (SLs) were analyzed for signatures of inorganic as well as semivolatile aromatic and low-volatile organic constituents. High variations in organic carbon (OC) emissions of BCB emissions, ranging from 5 to 22 mg MJ-1, were associated to variations in carbon monoxide (CO) emissions, ranging from 900 to 1900 mg MJ-1. Residential BCB combustion turned out to be an equally important source of levoglucosan, an established biomass burning marker, as spruce logwood combustion, but showed distinct higher ratios to manosan and galactosan. Signatures of polycyclic aromatic hydrocarbons emitted by BCB combustion exhibited defunctionalization and desubstitution with increasing combustion quality. Lastly, the concept of island and archipelago structural motifs adapted from petroleomics is used to describe the fraction low-volatile organic compounds in particulate emissions, where a transition from archipelago to island motifs in relation with decreasing CO emissions was observed in BCB emissions, while emissions from SL combustion exhibited the island motif.

Identification and Parametrization of Key Factors Affecting Levoglucosan Emission During Solid Fuel Burning.

Levoglucosan (LG) is a pyrolysis product of cellulose and hemicellulose at low combustion temperatures. However, LG release cannot be determined only by considering the contents of cellulose and hemicellulose exclusively due to the complexity of combustion processes and the physical-chemical properties of the fuel. This study detected the emission factors (EFs) of LG from 22 different solid fuel samples (including coal and biomass) by considering 18 different fuel properties and five combustion parameters. The average LGEFs during solid fuel burning varied in a range of 0.03-136 mg kg-1, with a magnitude difference of 1-4 orders. While the variations in cellulose (59.5-368 mg g-1) and hemicellulose (73.5-165 mg g-1) contents of fuel samples were only one- to 6-fold. A short combustion duration (<150 min) and a medium combustion temperature (200-400 °C) influenced by volatile and ash contents are crucial for the generation and accumulation of LG. A random forest coupled with the Akaike information criterion stepwise regression model successfully explained 96% of the total LG emission variation using three variables (ash content, cellulose content, and modified combustion efficiency). The ash content promoted coke formation and LG chain cracking by increasing the pyrolysis temperature and is considered the most important factor. The alkali metal in ash can reduce the energy barrier of intramolecular ring contraction reactions and inhibit the dehydration reactions, which led to additional heat being utilized by the competitive pathways of LG formation. This study provided a method to address the parametrization and release mechanisms of combustion source emissions.

Development of Spatio-Temporal Land Use Regression Models for Fine Particulate Matter and Wood-Burning Tracers in Temuco, Chile.

Biomass burning is common in much of the world, and in some areas, residential wood-burning has increased. However, air pollution resulting from biomass burning is an important public health problem. A sampling campaign was carried out between May 2017 and July 2018 in over 64 sites in four sessions, to develop a spatio-temporal land use regression (LUR) model for fine particulate matter (PM) and wood-burning tracers levoglucosan and soluble potassium (Ksol) in a city heavily impacted by wood-burning. The mean (sd) was 46.5 (37.4) µg m-3 for PM2.5, 0.607 (0.538) µg m-3 for levoglucosan, and 0.635 (0.489) µg m-3 for Ksol. LUR models for PM2.5, levoglucosan, and Ksol had a satisfactory performance (LOSOCV R2), explaining 88.8%, 87.4%, and 87.3% of the total variance, respectively. All models included sociodemographic predictors consistent with the pattern of use of wood-burning in homes. The models were applied to predict concentrations surfaces and to estimate exposures for an epidemiological study.

Isolation and Characterization of Levoglucosan-Metabolizing Bacteria.

Bacteria were isolated from wastewater and soil containing charred wood remnants based on their ability to use levoglucosan as a sole carbon source and on their levoglucosan dehydrogenase (LGDH) activity. On the basis of their 16S rRNA gene sequences, these bacteria represented the diverse genera Microbacterium, Paenibacillus, Shinella, and Klebsiella. Genomic sequencing of the isolates verified that two isolates represented novel species, Paenibacillus athensensis MEC069T and Shinella sumterensis MEC087T, while the remaining isolates were closely related to Microbacterium lacusdiani or Klebsiella pneumoniae. The genetic sequence of LGDH, lgdA, was found in the genomes of these four isolates as well as Pseudarthrobacter phenanthrenivorans Sphe3. The identity of the P. phenanthrenivorans LGDH was experimentally verified following recombinant expression in Escherichia coli. Comparison of the putative genes surrounding lgdA in the isolate genomes indicated that several other gene products facilitate the bacterial catabolism of levoglucosan, including a putative sugar isomerase and several transport proteins. IMPORTANCE Levoglucosan is the most prevalent soluble carbohydrate remaining after high-temperature pyrolysis of lignocellulosic biomass, but it is not fermented by typical production microbes such as Escherichia coli and Saccharomyces cerevisiae. A few fungi metabolize levoglucosan via the enzyme levoglucosan kinase, while several bacteria metabolize levoglucosan via levoglucosan dehydrogenase. This study describes the isolation and characterization of four bacterial species that degrade levoglucosan. Each isolate is shown to contain several genes within an operon involved in levoglucosan degradation, furthering our understanding of bacteria that metabolize levoglucosan.

A fast, single column high-performance anion exchange chromatography with pulsed amperometric detection method for the determination of saccharides in atmospheric aerosol samples.

Saccharides, especially anhydro sugars present in atmospheric aerosols, can be used as tracers to track sources of atmospheric aerosols. High-performance anion-exchange chromatography with pulsed amperometric detection is a commonly used technique for determining these saccharides, but the reported methods suffer from three drawbacks. First, to achieve separation of the complete set of atmospheric saccharides, run times are very long, typically longer than 60 minutes. Second, some methods require two columns to achieve the desired separation. Finally, in an era when electrolytic eluent preparation allows for excellent precision and accuracy, these methods require manually prepared eluents, which can lead to separation inconsistency for closely eluting analytes. These drawbacks make existing methods difficult to automate. To address this issue, we developed a fast method that uses only a single column for separation and electrolytically generated eluent that resolves 12 key atmospheric aerosol saccharides in 20 minutes. The resolved saccharides include anhydro sugars (levoglucosan, galactosan, and mannosan), sugar alcohols (erythritol, xylitol, and mannitol), and mono-/disaccharides (arabinose, galactose, glucose, mannose, fructose, and sucrose). To our knowledge, this report is the first instance of achieving such a significant reduction in run time with good resolution for this set of saccharides.

Accelerated and Natural Aging of Cellulose-Based Paper: Py-GC/MS Method.

Samples of papers artificially (2 to 60 days) and naturally (10, 45, and 56 years) aged were studied by the Py-GC/MS method to identify decomposition products. Possible reaction scenarios for cellulose degradation were developed. One of the degradation products is acetic acid, which can (auto)catalyze the cleavage of cellulose ß(1→4)-glycosidic bonds of cellulose polymer chains. However, during 20 s of Py-GC/MS analysis, temperatures of up to 300 °C did not significantly increase or modify the formation of decomposition products of paper components. At 300 °C, the amount of several cellulose decomposition products increased regularly depending on the number of days of artificial aging and natural aging, demonstrated mainly by the generation of 2-furancarboxaldehyde, 5-hydroxymethylfurfural, and levoglucosan and its consecutive dehydration products. No correlation between the amount of lignin decomposition products and the time of aging was found when the pyrolysis was performed at 300 °C and 500 °C. Compounds present in the products of decomposition at 500 °C bear the imprint of the chemical composition of the sampled paper. Pyrograms taken at 300 °C using the Py-GC/MS method can give additional information on the changes in the chemical structure of paper during natural or artificial aging, mainly about the cleavage of ß(1→4)-glycosidic bonds during aging.

Negligible Quantities of Particulate Low-Temperature Pyrogenic Carbon Reach the Atlantic Ocean via the Amazon River.

Particulate pyrogenic carbon (PyC) transported by rivers and aerosols, and deposited in marine sediments, is an important part of the carbon cycle. The chemical composition of PyC is temperature dependent and levoglucosan is a source-specific burning marker used to trace low-temperature PyC. Levoglucosan associated to particulate material has been shown to be preserved during riverine transport and marine deposition in high- and mid-latitudes, but it is yet unknown if this is also the case for (sub)tropical areas, where 90% of global PyC is produced. Here, we investigate transport and deposition of levoglucosan in suspended and riverbed sediments from the Amazon River system and adjacent marine deposition areas. We show that the Amazon River exports negligible amounts of levoglucosan and that concentrations in sediments from the main Amazon tributaries are not related to long-term mean catchment-wide fire activity. Levoglucosan concentrations in marine sediments offshore the Amazon Estuary are positively correlated to total organic content regardless of terrestrial or marine origin, supporting the notion that association of suspended or dissolved PyC to biogenic particles is critical in the preservation of PyC. We estimate that 0.5-10 × 106 g yr-1 of levoglucosan is exported by the Amazon River. This represents only 0.5-10 ppm of the total exported PyC and thereby an insignificant fraction, indicating that riverine derived levoglucosan and low-temperature PyC in the tropics are almost completely degraded before deposition. Hence, we suggest caution in using levoglucosan as tracer for past fire activity in tropical settings near rivers.

Impacts of Chemical Degradation on the Global Budget of Atmospheric Levoglucosan and Its Use As a Biomass Burning Tracer.

Levoglucosan has been widely used to quantitatively assess biomass burning's contribution to ambient aerosols, but previous such assessments have not accounted for levoglucosan's degradation in the atmosphere. We develop the first global simulation of atmospheric levoglucosan, explicitly accounting for its chemical degradation, to evaluate the impacts on levoglucosan's use in quantitative aerosol source apportionment. Levoglucosan is emitted into the atmosphere from the burning of plant matter in open fires (1.7 Tg yr-1) and as biofuels (2.1 Tg yr-1). Sinks of atmospheric levoglucosan include aqueous-phase oxidation (2.9 Tg yr-1), heterogeneous oxidation (0.16 Tg yr-1), gas-phase oxidation (1.4 × 10-4 Tg yr-1), and dry and wet deposition (0.27 and 0.43 Tg yr -1). The global atmospheric burden of levoglucosan is 19 Gg with a lifetime of 1.8 days. Observations show a sharp decline in levoglucosan's concentrations and its relative abundance to organic carbon aerosol (OC) and particulate K+ from near-source to remote sites. We show that such features can only be reproduced when levoglucosan's chemical degradation is included in the model. Using model results, we develop statistical parametrizations to account for the atmospheric degradation in levoglucosan measurements, improving their use for quantitative aerosol source apportionment.

PM10 chemical composition at a residential site in the western mediterranean: Estimation of the contribution of biomass burning from levoglucosan and its isomers.

The composition of PM10, including molecular markers of biomass burning (levoglucosan, mannosan and galactosan), was determined at a residential site in southeastern Spain during winter and early spring. The average PM10 concentration was 25.0 µg m-3, being organic carbon (OC, 6.77 µg m-3), NO3- (2.02 µg m-3), SO42- (1.36 µg m-3) and Ca2+ (1.01 µg m-3) the main components. Levoglucosan was the dominant anhydrosugar (143 ng m-3), accounting for 81% of the total concentration of monosaccharide anhydrides. The average contribution of biomass combustion to OC, estimated from the levoglucosan data, was 23%. This value agreed well with that calculated by Positive Matrix Factorization (PMF, 25%). The PMF model resolved six factors that were assigned to road traffic (28%), secondary aerosols (27%), soil dust (14%), fresh sea salt (13%), aged sea salt (10%) and biomass burning (8%). This model was used to estimate the OC/Levoglucosan and PM10/Levoglucosan emission ratios for the study area.

Identification, functional characterization, and crystal structure determination of bacterial levoglucosan dehydrogenase.

Levoglucosan is the 1,6-anhydrosugar of d-glucose formed by pyrolysis of glucans and is found in the environment and industrial waste. Two types of microbial levoglucosan metabolic pathways are known. Although the eukaryotic pathway involving levoglucosan kinase has been well-studied, the bacterial pathway involving levoglucosan dehydrogenase (LGDH) has not been well-investigated. Here, we identified and cloned the lgdh gene from the bacterium Pseudarthrobacter phenanthrenivorans and characterized the recombinant protein. The enzyme exhibited high substrate specificity toward levoglucosan and NAD+ for the oxidative reaction and was confirmed to be LGDH. LGDH also showed weak activities (∼4%) toward l-sorbose and 1,5-anhydro-d-glucitol. The reverse (reductive) reaction using 3-keto-levoglucosan and NADH exhibited significantly lower Km and higher kcat values than those of the forward reaction. The crystal structures of LGDH in the apo and complex forms with NADH, NADH + levoglucosan, and NADH + l-sorbose revealed that LGDH has a typical fold of Gfo/Idh/MocA family proteins, similar to those of scyllo-inositol dehydrogenase, aldose-aldose oxidoreductase, 1,5-anhydro-d-fructose reductase, and glucose-fructose oxidoreductase. The crystal structures also disclosed that the active site of LGDH is distinct from those of these enzymes. The LGDH active site extensively recognized the levoglucosan molecule with six hydrogen bonds, and the C3 atom of levoglucosan was closely located to the C4 atom of NADH nicotinamide. Our study is the first molecular characterization of LGDH, providing evidence for C3-specific oxidation and representing a starting point for future biotechnological use of LGDH and levoglucosan-metabolizing bacteria.

Separating spatial patterns in pollution attributable to woodsmoke and other sources, during daytime and nighttime hours, in Christchurch, New Zealand.

During winter nights, woodsmoke may be a predominant source of air pollution, even in cities with many sources. Since two major earthquakes resulted in major structural damage in 2010 and 2011, reliance on woodburning for home heating has increased substantially in Christchurch, New Zealand (NZ), along with intensive construction/demolition activities. Further, because NZ is a relatively isolated western country, it offers the unique opportunity to disentangle multiple source impacts in the absence of long-range transport pollution. Finally, although many spatial saturation studies have been published, and levoglucosan is an established tracer for woodburning emissions, few studies have monitored multiple sites simultaneously for this or other organic constituents, with the ability to distinguish spatial patterns for daytime vs. nighttime hours, in complex urban settings. We captured seven-day integrated samples of PM2.5, and elemental and organic tracers of woodsmoke and diesel emissions, during "daytime" (7 a.m. - 5:30 p.m.) and "nighttime" (7 p.m. - 5:30 a.m.) hours, at nine sites across commercial and residential areas, over three weeks in early winter (May 2014). At a subset of six sites, we also sampled during hypothesized "peak" woodburning hours (7 p.m. - 12 a.m.), to differentiate emissions during "active" residential woodburning, vs. overnight smouldering. Concentrations of PM2.5 were, on average, were twice as high during nighttime than daytime [µâ€¯= 18.4 (SD = 6.13) vs. 9.21 (SD = 6.13) µg/m3], with much greater differences in woodsmoke tracers (i.e., levoglucosan [µâ€¯= 1.83 (SD = 0.82) vs. 0.34 (SD = 0.17) µg/m3], potassium) and indicators of treated- or painted-wood burning (e.g., arsenic, lead). Only nitrogen dioxide, calcium, iron, and manganese (tracers of vehicular emissions) were higher during daytime. Levoglucosan and most PAHs were higher during "active" woodburning, vs. overnight smouldering. Our time-stratified spatial saturation detected strong spatial variability throughout the study area, which distinctly differed during daytime vs. night time hours, and quantified the substantial contribution of woodsmoke to overnight spatial variation in PM2.5 across Christchurch. Daytime vs. nighttime differences were greater than those observed across sites. Traffic, especially diesel, contributed substantially to daytime NO2 and spatial gradients in non-woodsmoke constituents.

Methods for the determination of levoglucosan and other sugar anhydrides as biomass burning tracers in environmental samples - A review.

Nowadays, there is a great pressure on finding an alternative source of energy. One such source is biomass combustion. Biomass is any organic matter such as wood, crops, seaweed, and animal wastes that during combustion emits energy but also smoke and solid residue. Biomass burning tracers, such as levoglucosan, mannosan and galactosan, are sugar anhydrides produced during burning of biomass that contain cellulose and hemicellulose. Analysis of environmental samples for tracers is the source of information about the type of biofuel burned. In this article, a literature review of the preparation and determination of biomass burning tracers for environmental samples was presented. The review discusses the preparation of different samples (particulate matter, soils, sediments, biological samples), extraction, derivatization, and determination. Amongst determination methods the most popular was gas chromatography with mass spectrometry but other techniques were also used, such as high-performance liquid chromatography with aerosol charge detection, capillary electrophoresis with pulsed amperometric detection, and ion chromatography with pulsed amperometric detection.

A Study of Intramolecular Hydrogen Bonding in Levoglucosan Derivatives.

Organofluorine is a weak hydrogen-bond (HB) acceptor. Bernet et al. have demonstrated its capability to perturb OH···O intramolecular hydrogen bonds (IMHBs), using conformationally rigid carbohydrate scaffolds including levoglucosan derivatives. These investigations are supplemented here by experimental and theoretical studies involving six new levoglucosan derivatives, and complement the findings of Bernet et al. However, it is shown that conformational analysis is instrumental in interpreting the experimental data, due to the occurrence of non-intramolecular hydrogen-bonded populations which, although minor, cannot be neglected and appears surprisingly significant. The DFT conformational analysis, together with the computation of NMR parameters (coupling constants and chemical shifts) and wavefunction analyses (AIM, NBO), provides a full picture. Thus, for all compounds, the most stabilized structures show the OH groups in a conformation allowing IMHB with O5 and O6, when possible. Furthermore, the combined approach points out the occurrence of various IMHBs and the effect of the chemical modulations on their features. Thus, two-center or three-center IMHB interactions are observed in these compounds, depending on the presence or absence of additional HB acceptors, such as methoxy or fluorine.

Producing glucose 6-phosphate from cellulosic biomass: structural insights into levoglucosan bioconversion.

The most abundant carbohydrate product of cellulosic biomass pyrolysis is the anhydrosugar levoglucosan (1,6-anhydro-ß-d-glucopyranose), which can be converted to glucose 6-phosphate by levoglucosan kinase (LGK). In addition to the canonical kinase phosphotransfer reaction, the conversion requires cleavage of the 1,6-anhydro ring to allow ATP-dependent phosphorylation of the sugar O6 atom. Using x-ray crystallography, we show that LGK binds two magnesium ions in the active site that are additionally coordinated with the nucleotide and water molecules to result in ideal octahedral coordination. To further verify the metal binding sites, we co-crystallized LGK in the presence of manganese instead of magnesium and solved the structure de novo using the anomalous signal from four manganese atoms in the dimeric structure. The first metal is required for catalysis, whereas our work suggests that the second is either required or significantly promotes the catalytic rate. Although the enzyme binds its sugar substrate in a similar orientation to the structurally related 1,6-anhydro-N-acetylmuramic acid kinase (AnmK), it forms markedly fewer bonding interactions with the substrate. In this orientation, the sugar is in an optimal position to couple phosphorylation with ring cleavage. We also observed a second alternate binding orientation for levoglucosan, and in these structures, ADP was found to bind with lower affinity. These combined observations provide an explanation for the high Km of LGK for levoglucosan. Greater knowledge of the factors that contribute to the catalytic efficiency of LGK can be used to improve applications of this enzyme for levoglucosan-derived biofuel production.

Bioconversion of anhydrosugars: Emerging concepts and strategies.

As methods for the use of anhydrosugars in chemical and biofuel production continue to develop, our collective knowledge of anhydrosugar processing enzymes continues to improve, including their mechanistic details, structural dynamics and modes of substrate binding. Of particular interest, anhydrosugar kinases, such as levoglucosan kinase (LGK) and 1,6-anhydro-N-acetylmuramic acid kinase (AnmK), utilize an unusual mechanism whereby the sugar substrate is both cleaved and phosphorylated. The phosphorylated sugar can then be routed to other metabolic pathways, thereby allowing its further bioconversion. Advanced engineering efforts to improve the catalytic efficiency and stability of LGK have been steadily progressing. Other enzymes that cleave the glycosidic bond of disaccharide sugars containing an anhydrosugar component are also being identified and characterized. Accordingly, the potential future use of these enzymes in large-scale production strategies is becoming increasingly viable. Here, a mini-review of the observed characteristics of anhydrosugar processing enzymes is presented along with recent developments in the bioconversion of these sugars. © 2016 IUBMB Life 68(9):700-708, 2016.

Production of biorenewable styrene: utilization of biomass-derived sugars and insights into toxicity.

Fermentative production of styrene from glucose has been previously demonstrated in Escherichia coli. Here, we demonstrate the production of styrene from the sugars derived from lignocellulosic biomass depolymerized by fast pyrolysis. A previously engineered styrene-producing strain was further engineered for utilization of the anhydrosugar levoglucosan via expression of levoglucosan kinase. The resulting strain produced 240 ± 3 mg L(-1) styrene from pure levoglucosan, similar to the 251 ± 3 mg L(-1) produced from glucose. When provided at a concentration of 5 g L(-1), pyrolytic sugars supported styrene production at titers similar to those from pure sugars, demonstrating the feasibility of producing this important industrial chemical from biomass-derived sugars. However, the toxicity of contaminant compounds in the biomass-derived sugars and styrene itself limit further gains in production. Styrene toxicity is generally believed to be due to membrane damage. Contrary to this prevailing wisdom, our quantitative assessment during challenge with up to 200 mg L(-1) of exogenously provided styrene showed little change in membrane integrity; membrane disruption was observed only during styrene production. Membrane fluidity was also quantified during styrene production, but no changes were observed relative to the non-producing control strain. This observation that styrene production is much more damaging to the membrane integrity than challenge with exogenously supplied styrene provides insight into the mechanism of styrene toxicity and emphasizes the importance of verifying proposed toxicity mechanisms during production instead of relying upon results obtained during exogenous challenge.

Engineering levoglucosan metabolic pathway in Rhodococcus jostii RHA1 for lipid production.

Oleaginous strains of Rhodococcus including R. jostii RHA1 have attracted considerable attention due to their ability to accumulate triacylglycerols (TAGs), robust growth properties and genetic tractability. In this study, a novel metabolic pathway was introduced into R. jostii by heterogenous expression of the well-characterized gene, lgk encoding levoglucosan kinase from Lipomyces starkeyi YZ-215. This enables the recombinant R. jostii RHA1 to produce TAGs from the anhydrous sugar, levoglucosan, which can be generated efficiently as the major molecule from the pyrolysis of cellulose. The recombinant R. jostii RHA1 could grow on levoglucosan as the sole carbon source, and the consumption rate of levoglucosan was determined. Furthermore, expression of one more copy of lgk increased the enzymatic activity of LGK in the recombinant. However, the growth performance of the recombinant bearing two copies of lgk on levoglucosan was not improved. Although expression of lgk in the recombinants was not repressed by the glucose present in the media, glucose in the sugar mixture still affected consumption of levoglucosan. Under nitrogen limiting conditions, lipid produced from levoglucosan by the recombinant bearing lgk was up to 43.54 % of the cell dry weight, which was comparable to the content of lipid accumulated from glucose. This work demonstrated the technical feasibility of producing lipid from levoglucosan, an anhydrosugar derived from the pyrolysis of lignocellulosic materials, by the genetically modified rhodococci strains.

Gas chromatography-mass spectrometry metabolomics of goat milk with different polymorphism at the αS1-casein genotype locus.

Hyphenated gas chromatography-mass spectrometry (GC-MS) and multivariate data analysis techniques were used to uncover milk metabolite differences in different αS1-casein genotypes of goats. By a discriminant GC-MS metabolomics approach, we characterized milk polar metabolites of 28 goats. Animals were selected on the basis of their genotypes as 7 goats classified heterozygous for weak or null alleles, 5 for the genotype EE, 9 for the genotypes AE and BE, and finally 7 for the strong genotype AA. Low molecular weight polar metabolite profile was tightly related to the different goat genotypes, milk production, and protein levels. Results of multivariate statistical analysis of GC-MS data demonstrate that different heterozygous and homozygous genotypes expressed different metabolites such as citric and aconitic acid for the strong allele class with different sugars and polyols for the weak class.

Compound-specific stable carbon isotopic signature of carbohydrate pyrolysis products from C3 and C4 plants.

BACKGROUND: Pyrolysis-compound specific isotopic analysis (Py-CSIA: Py-GC-(FID)-C-IRMS) is a relatively novel technique that allows on-line quantification of stable isotope proportions in chromatographically separated products released by pyrolysis. Validation of the Py-CSIA technique is compulsory for molecular traceability in basic and applied research. In this work, commercial sucrose from C4 (sugarcane) and C3 (sugarbeet) photosystem plants and admixtures were studied using analytical pyrolysis (Py-GC/MS), bulk δ(13)C IRMS and δ(13)C Py-CSIA. RESULTS: Major pyrolysis compounds were furfural (F), furfural-5-hydroxymethyl (HMF) and levoglucosan (LV). Bulk and main pyrolysis compound δ(13)C (‰) values were dependent on plant origin: C3 (F, -24.65 ± 0.89; HMF, -22.07 ± 0.41‰; LV, -21.74 ± 0.17‰) and C4 (F, -14.35 ± 0.89‰; HMF, -11.22 ± 0.54‰; LV, -11.44 ± 1.26‰). Significant regressions were obtained for δ(13)C of bulk and pyrolysis compounds in C3 and C4 admixtures. Furfural (F) was found (13)C depleted with respect to bulk and HMF and LV, indicating the incorporation of the light carbon atom in position 6 of carbohydrates in the furan ring after pyrolysis. CONCLUSION: This is the first detailed report on the δ(13)C signature of major pyrolytically generated carbohydrate-derived molecules. The information provided by Py-CSIA is valuable for identifying source marker compounds of use in food science/fraud detection or in environmental research.

Microbial conversion of pyrolytic products to biofuels: a novel and sustainable approach toward second-generation biofuels.

This review highlights the potential of the pyrolysis-based biofuels production, bio-ethanol in particular, and lipid in general as an alternative and sustainable solution for the rising environmental concerns and rapidly depleting natural fuel resources. Levoglucosan (1,6-anhydrous-ß-D-glucopyranose) is the major anhydrosugar compound resulting from the degradation of cellulose during the fast pyrolysis process of biomass and thus the most attractive fermentation substrate in the bio-oil. The challenges for pyrolysis-based biorefineries are the inefficient detoxification strategies, and the lack of naturally available efficient and suitable fermentation organisms that could ferment the levoglucosan directly into bio-ethanol. In case of indirect fermentation, acid hydrolysis is used to convert levoglucosan into glucose and subsequently to ethanol and lipids via fermentation biocatalysts, however the presence of fermentation inhibitors poses a big hurdle to successful fermentation relative to pure glucose. Among the detoxification strategies studied so far, over-liming, extraction with solvents like (n-butanol, ethyl acetate), and activated carbon seem very promising, but still further research is required for the optimization of existing detoxification strategies as well as developing new ones. In order to make the pyrolysis-based biofuel production a more efficient as well as cost-effective process, direct fermentation of pyrolysis oil-associated fermentable sugars, especially levoglucosan is highlly desirable. This can be achieved either by expanding the search to identify naturally available direct levoglusoan utilizers or modify the existing fermentation biocatalysts (yeasts and bacteria) with direct levoglucosan pathway coupled with tolerance engineering could significantly improve the overall performance of these microorganisms.