Fabrication and Properties of a Biodegradable Zn-Ca Composite.

In recent years, Zn and its alloys have become some of the most promising degradable metals as in vivo implants due to their acceptable biocompatibility and more suitable degradation rate compared with Mg-based and Fe-based alloys. However, the degradation rate of Zn-based materials after implantation in the body for orthopedic applications is relatively slow, leading to long-term retention of the implants after fulfilling their missions. Moreover, the excessive release of Zn2+ during the degradation process of Zn-based implants usually leads to high cytotoxicity and delayed osseointegration. To provide a feasible solution to the problem faced by Zn-based implants, a Zn-Ca composite was fabricated by an air pressure infiltration method in this work. The XRD pattern of the composite suggests that the composite is fully composed of Zn-Ca intermetallic compounds. The degradation tests in vitro show that the composite has a much higher degradation rate than pure Zn, and the high Ca content regions in the composite can preferentially degrade as sacrificial anodes. In addition, the composite can efficiently induce Ca-P deposition during immersion tests in Hank's solution. Cytotoxicity tests indicate that L-929 cells exhibit around 82% cell viability (Grade 1) even after being cultured in the 100% extract prepared from the Zn-Ca composite for 1 day and show excellent cell viability.

The in vivo and in vitro corrosion behavior of MgO/Mg-Zn-Ca composite with different Zn/Ca ratio.

The effect of Zn/Ca ratio on the corrosion behavior of Mg-3Zn-0.2Ca-1.0MgO (3ZX) and Mg-1Zn-0.2Ca-1.0MgO (ZX) was investigated on the as-extruded specimens. Microstructure observations revealed that the low Zn/Ca ratio led to the grain growth from 1.6 µm in 3ZX to 8.1 µm in ZX. At the same time, the low Zn/Ca ratio changed the nature of second phase from the existence of Mg-Zn and Ca2Mg6Zn3 phases in 3ZX to the dominated Ca2Mg6Zn3 phase in ZX. The local galvanic corrosion caused by the excessive potential difference was alleviated obviously due to the missing of MgZn phase in ZX. Besides, the in vivo experiment also showed that ZX composite exhibited a good corrosion performance and the bone tissue around the implant grew well.

Fabrication of biodegradable HA/Mg-Zn-Ca composites and the impact of heterogeneous microstructure on mechanical properties, in vitro degradation and cytocompatibility.

Due to their desirable elastic modulus and density that are similar to natural bone, non-toxic element containing magnesium alloys are regarded as promising bio-degradable materials. A biodegradable HA-particle-reinforced magnesium-matrix composite Mg-3Zn-0.2Ca-1HA (wt%) was fabricated for biomedical application by a combination of high shear solidification (HSS) and hot extrusion technology. The microstructure, mechanical properties, corrosion resistance and cell biocompatibility of the composite were subsequently investigated. In comparison with the matrix alloy, the as-cast Mg-3Zn-0.2Ca-1HA composite obtained by HSS technology exhibited a uniform and fine grained structure, further refined after a hot extrusion ratio of 36:1. The yield strength (0.2%YS), ultimate tensile strength and elongation of the extruded composite were 322 MPa, 341 MPa and 7.6%, respectively. The corrosion rate of the as-extruded Mg-3Zn-0.2Ca-1HA composite was measured to be 1.52 mm/y. Electrochemical and immersion tests showed that the corrosion resistance of the composite is slightly improved comparing to that of the matrix alloy.

Effects of solidification cooling rate on the corrosion resistance of a biodegradable ß-TCP/Mg-Zn-Ca composite.

Biodegradable beta-tricalcium phosphate (ß-TCP) particle reinforced magnesium metal matrix composites (Mg-MMC) have attracted increasing interest for application as implant materials. This investigation was conducted to study the effect of cooling rate on the microstructure and corrosion behavior of a biodegradable ß-TCP/Mg-Zn-Ca composite. The composite was fabricated under a series of cooling rates using a wedge-shaped casting mold. The microstructure of the composite was examined by optical and scanning electron microscopy, and the corrosion behavior was investigated using an electrochemical workstation and immersion tests in a simulated body fluid (SBF). Faster cooling rates were shown to refine the secondary phase and grain size, and produce a more homogenous microstructure. The refined microstructure resulted in a more uniform distribution of ß-TCP particles, which is believed to be beneficial in the formation of a stable and compact corrosion product layer, leading to improved corrosion resistance for the composite.