Enhancing cellulose acetate biodegradability in cigarette filters: an in-depth analysis of thermal alkaline pretreatment, microbial dynamics, and breakdown pathway prediction.

BACKGROUND: The demand for bioplastics has increased exponentially as they have emerged as alternatives to petrochemical plastics. However, there is a substantial lack of knowledge regarding bioplastic degradation. This study developed a novel pretreatment method to improve the accessibility of a bioplastic substrate for biodegradation. In this study, cellulose acetate, a bioplastic found in the world's most littered waste, e.g. cigarette filters, was selected as a potential substrate. Before anaerobic digestion, three thermal alkaline pretreatments: TA 30 °C, TA 90 °C, and TA 121 °C, were used to evaluate their effects on the chemical alterations of cellulose acetate. RESULT: The ester groups in cellulose acetate were significantly reduced by the TA 30 °C pretreatment, as seen by a decrease in C = O stretching vibrations and shortening of C - O stretches (1,270 ∼ 1,210 cm- 1), indicating effective removal of acetyl groups. This pretreatment significantly enhanced cellulose acetate biodegradability to a maximum of 91%, surpassing the previously reported cellulose acetate degradation. Methane production increased to 695.0 ± 4 mL/g of volatile solid after TA 30 °C pretreatment, indicating enhanced cellulose acetate accessibility to microorganisms, which resulted in superior biogas production compared to the control (306.0 ± 10 mL/g of volatile solid). Diverse microbes in the anaerobic digestion system included hydrolytic (AB240379_g, Acetomicrobium, FN436103_g, etc.), fermentative, and volatile fatty acids degrading bacteria (JF417922_g, AB274492_g, Coprothermobacter, etc.), with Methanobacterium and Methanothermobacter being the sole hydrogenotrophic methanogens in the anaerobic digestion system. Additionally, an attempt to predict the pathway for the effective degradation of cellulose acetate from the microbial community in different pretreatment conditions. CONCLUSIONS: To the best of our knowledge, this is the first study to estimate the maximum cellulose acetate degradation rate, with a simple and cost-effective pretreatment procedure. This approach holds promise for mitigating the environmental impact of cellulose acetate of cigarette filters and presents a sustainable and economically viable waste management strategy.

Preparation of cellulose acetate based flexible separator and its application in zinc-air batteries.

Flexible solid-state zinc-air batteries as a wearable energy storage device with great potential, and their separators, which control ion permeability, inhibit zinc dendrite generation, and regulate catalytic active sites, have been developed as gel electrolyte separators with high retention of electrolyte uptake. However, the gel electrolyte separator still has problems such as poor affinity with the electrolyte and poor ionic conductivity, which limits its further application. In order to further improve the electrolyte absorption, ionic conductivity and mechanical strength of cellulose acetate(CA)/polyvinyl alcohol (PVA) nanofibers, TiO2was added to CA/PVA to increase the porosity, and glutaraldehyde (GA) was used to modify the CA/PVA/TiO2separator by acetal reaction with CA and PVA to make the molecules closely linked. The results shows that the optimal mass fractions of TiO2and GA were 2% and 5%, respectively. At this time, the porosity and absorption rate of the separator increased from 48% to 68.2% and 142.4% to 285.3%, respectively. The discharge capacity reached 179 mA cm-3, and the cycle stability rate was 89% after 7 stable constant current charge/discharge cycles.

Reinforcing decellularized small intestine submucosa with cellulose acetate nanofibrous and silver nanoparticles as a scaffold for wound healing applications.

BACKGROUND: The formation of chronic wounds accounts for considerable costs in health care systems. Despite the several benefits of decellularized small intestinal submucosa (SIS) as an appropriate scaffold for different tissue regeneration, it has shortcomings such as lack of antibacterial features and inappropriate mechanical properties for skin tissue regeneration. We aimed to examine the efficacy and safety of decellularized SIS scaffold enhanced with cellulose acetate (CA) and silver (Ag) nanoparticles (NPs) for healing full-thickness wounds. METHODS AND RESULTS: The scaffolds were prepared by decellularizing bovine SIS and electrospinning CA/Ag nanoparticles and characterized using a transmission electron microscope (TEM), scanning electron microscope (SEM), tensile testing, and X-ray diffraction. In vivo evaluations were performed using full-thickness excisions covered with sterile gauze as the control group, SIS, SIS/CA, and SIS/CA/Ag scaffolds on the dorsum of twenty male Wistar rats divided into four groups randomly with 21-days follow-up. All in vivo specimens underwent Masson's trichrome (MT) staining for evaluation of collagen deposition, transforming growth factor-ß (TGF-ß) immunohistochemistry (IHC), and Haematoxylin Eosin (H&E) staining. The IHC and MT data were analyzed with the ImageJ tool by measuring the stained area. The TEM results revealed that Ag nanoparticles are successfully incorporated into CA nanofibers. Assessment of scaffolds hydrophilicity demonstrated that the contact angle of SIS/CA/Ag scaffold was the lowest. The in vivo results indicated that the SIS/CA/Ag scaffold had the most significant wound closure. H&E staining of the in vivo specimens showed the formation of epidermal layers in the SIS/CA/Ag group on day 21. The percentage of the stained area of MT and TGF-ß IHC staining's was highest in the SIS/CA/Ag group. CONCLUSION: The decellularized SIS/CA/Ag scaffolds provided the most significant wound closure compared to other groups and caused the formation of epidermal layers and skin appendages. Additionally, the collagen deposition and expression of TGF-ß increased significantly in SIS/CA/Ag group.

Copper oxide(I) nanoparticle-modified cellulose acetate membranes with enhanced antibacterial and antifouling properties.

Cellulose acetate membranes exhibit a potential to be applied in hemodialysis. However, their performance is limited by membrane fouling and a lack of antibacterial properties. In this research, copper oxide (I) nanoparticles were fabricated in situ into a cellulose acetate matrix in the presence of polyvinylpyrrolidone (pore-forming agent) and sulfobetaine (stabilising agent) to reduce the leakage of copper ions from nano-enhanced membranes. The influence of nanoparticles on the membrane structure and their antibacterial and antifouling properties were investigated. The results showed that incorporating Cu2O NPs imparted significant antibacterial properties against Staphylococcus aureus and fouling resistance under physiological conditions. The Cu2O NPs-modified membrane could pave the way for potential dialysis applications.

Biodegradable ultrafiltration membrane enhanced with anti-biofouling agent from Anacardium occidentale extract.

Our research focuses on developing environmentally friendly biodegradable ultrafiltration (UF) membranes for small-scale water purification in areas lacking infrastructure or during emergencies. To address biofouling challenges without resorting to harmful chemicals, we incorporate bio-based extracts, such as methyl gallate from A. occidentale leaves, a Malaysian ulam herb, known for its quorum sensing inhibition (QSI) properties. The methyl gallate enriched extract was purified by solvent partitioning and integrated into cellulose-based UF membranes (0 to 7.5% w w-1) through phase inversion technique. The resulting membranes exhibited enhanced anti-organic fouling and anti-biofouling properties, with flux recovery ratio (FRR) of 87.84 ± 2.00% against bovine serum albumin and FRRs of 76.67 ± 1.89% and 69.57 ± 1.77% against E. coli and S. aureus, respectively. The CA/MG-5 membrane showed a 224% improvement in pure water flux (PWF) compared to the neat CA membrane. Our innovative approach significantly improves PWF, presenting an environmentally friendly method for biofouling prevention in UF membrane applications.

Self-healing and shape-memory polymers based on cellulose acetate matrix.

The creation of self-healing polymers with superior strength and stretchability from biodegradable materials is attracting increasing attention. In this study, we synthesized new biomass-derived cellulose acetate (CA) derivatives by ring-opening graft polymerization of δ-valerolactone followed by the introduction of ureidopyrimidinone (Upy) groups in the polymer side chains. Due to the semicrystalline aliphatic characteristics of the side chain poly(δ-valerolactone) (PVL) and quadruple hydrogen bonds formed by the Upy groups, the stretchability of the resulting polymers was significantly enhanced. Moreover, the shape memory ability and self-healing property (58.3% of self-healing efficiency) were successfully imparted to the polymer. This study demonstrates the great significance of using biomass sources to create self-healing polymers.

This paper describes the first successful demonstration of self-healing polymers with superior strength and stretchability from a biodegradable material, cellulose acetate (CA). We initially introduced the ureidopyrimidinone (Upy) groups in the side chains of CA. However, the resulting polymer was not soluble and processable. In order to solve this issue, a new strategy based on the ring-opening graft polymerization of δ-valerolactone followed by the introduction of ureidopyrimidinone (Upy) groups was adopted. Due to the semicrystalline aliphatic characteristics of the side chain poly(δ-valerolactone) (PVL), the resulting polymers were soluble and processable. In addition, the quadruple hydrogen bonds formed by the Upy groups enhanced the stretchability of the resulting polymers. Moreover, the shape memory ability and self-healing property were successfully achieved due to the presence of PVL and Upy. The developed new strategy can be applied to a variety of polymers including biomass-based polymers and materials.

Flexible Force Sensor Based on a PVA/AgNWs Nanocomposite and Cellulose Acetate.

Nanocomposites are materials of special interest for the development of flexible electronic, optical, and mechanical devices in applications such as transparent conductive electrodes and flexible electronic sensors. These materials take advantage of the electrical, chemical, and mechanical properties of a polymeric matrix, especially in force sensors, as well as the properties of a conductive filler such as silver nanowires (AgNWs). In this work, the fabrication of a force sensor using AgNWs synthesized via the polyol chemical technique is presented. The nanowires were deposited via drop-casting in polyvinyl alcohol (PVA) to form the active (electrode) and resistive (nanocomposite) sensor films, with both films separated by a cellulose acetate substrate. The dimensions of the resulting sensor are 35 mm × 40 mm × 0.1 mm. The sensor shows an applied force ranging from 0 to 3.92 N, with a sensitivity of 0.039 N. The sensor stand-off resistance, exceeding 50 MΩ, indicates a good ability to detect changes in applied force without an external force. Additionally, studies revealed a response time of 10 ms, stabilization of 9 s, and a degree of hysteresis of 1.9%. The voltage response of the sensor under flexion at an angle of 85° was measured, demonstrating its functionality over a prolonged period. The fabricated sensor can be used in applications that require measuring pressure on irregular surfaces or systems with limited space, such as for estimating movement in robot joints.

Porous microneedle arrays as promising tools for the quantification of drugs in the skin: a proof of concept study.

This study aimed to demonstrate the potential of using porous microneedles (PMNs) as a promising tool for the noninvasive quantification of topically applied pharmaceutical products. We fabricated a porous microneedle (PMN) from a blend of cellulose acetate and dimethyl sulfoxide by casting and phase separation; it was characterized using scanning electron microscopy, Raman spectroscopy, differential scanning calorimetry, and a Texture Analyzer. An ex vivo study was conducted as a proof-of-concept study to assess whether this PMN could be used to quantify drug absorption through the skin after the topical administration of two nonequivalent products of sodium ibuprofen (gel and dissolving microneedles). Three cellulose acetate formulations (PMN1: 37.5%, PMN-2: 44.4%, and PMN-3: 50%) were used to prepare PMN patches; subsequently, these were evaluated for their morphological and insertion properties. Only PMN-2 microneedle patches were chosen to continue with the ex vivo study. The ex vivo study results demonstrated that PMNs could absorb and release sodium ibuprofen (SDIB) and differentiate between two different SDIB topical products. This can be attributed to the porous and interconnected architecture of these microneedles. This developmental study highlights the potential success of such a tool for the quantification of dermal drug concentration and supports moving to in vivo tests.

Implications of Drug-Polymer Interactions on Time-Temperature-Transformation: A Tool to Assess the Crystallization Propensity in Amorphous Solid Dispersions.

The critical cooling rate (CRcrit) to prevent drug crystallization during the preparation of nifedipine amorphous solid dispersions (ASDs) was determined through the time-temperature-transformation (TTT) diagram. ASDs were prepared with polyvinylpyrrolidone, hydroxypropylmethyl cellulose acetate succinate, and poly(acrylic acid). ASDs were subjected to isothermal crystallization over a wide temperature range, and the time and temperature dependence of nifedipine crystallization onset time (tC) was determined by differential scanning calorimetry (DSC) and synchrotron X-ray diffractometry. TTT diagrams were generated for ASDs, which provided the CRcrit for the dispersions prepared with each polymer. The observed differences in CRcrit could be explained in terms of differences in the strength of interactions. Stronger drug-polymer interactions led to longer tC and decreased CRcrit. The effect of polymer concentrations (4-20% w/w) was also influenced by the strength of the interaction. The CRcrit of amorphous NIF was ∼17.5 °C/min. Addition of 20% w/w polymer resulted in a CRcrit of ∼0.05, 0.2, and 11 °C/min for the dispersions prepared with PVP, HPMCAS, and PAA, respectively.

Small Butt Harmful: Individual- and Population-Level Impacts of Cigarette Filter Particles on the Deposit-Feeding Polychaete Capitella teleta.

In the marine environment, discarded cigarette filters (CFs) deteriorate and leach filter-associated chemicals. The study aim was to assess the effects of smoked CFs (SCFs) and non-smoked CFs (NCFs) particles on individual life-history traits in the deposit-feeding polychaete Capitella teleta and extrapolate these to possible population-level effects. C. teleta was exposed to sediment-spiked particles of NCFs and SCFs at an environmentally realistic concentration (0.1 mg particles g-1 dw sed) and a 100-fold higher (10 mg particles g-1 dw sed) concentration. Experimental setup incorporated 11 individual endpoints and lasted approximately 6 months. There were significant effects on all endpoints, except from adult body volume and egestion rate, in worms exposed to 10 mg SCF particles g-1 dw sed. Although not statistically significant, there was ≥50% impact on time between reproductive events and number of eggs per female at 0.1 mg SCF particles g-1 dw sed. None of the endpoints was significantly affected by NCFs. Results suggest that SCFs are likely to affect individual life-history traits of C. teleta, whereas the population model suggests that these effects might not transform into population-level effects. The results further indicate that chemicals associated with CFs are the main driver causing the effects rather than the CF particles.

Synthesis & fabrication of O-linked polymeric hybrids for recovery of textile dyes: Closed loop economy.

Dyes are an important resource employed for the production systems in textile, paper, paint and leather industry. An estimate of 200,000 tons of dyes are discharged as textile effluent each year worldwide. It becomes imperative to recover these dyes by treating the effluents using economically viable routes. The present research was undertaken with the objective to attain zero emission and zero waste through development of novel polymeric hybrids as adsorbents. For this purpose, metal moieties (Al3+, Si4+, Ti4+ and Zr4+) were hybridized with polyacrylic acid, and cellulose acetate for the uptake of selected dyes under optimized parameters. The structural elucidation of four synthesized hybrids (MP-Al, MP-Si, MP-Ti and MP-Zr) by FTIR, EDX and TGA confirmed O-linked grafting of metal moieties with polymers and thermally stable porous materials. SEM micrographic images displayed void spaces providing channels for effective adsorption. The batch experiments demonstrated removal of malachite green (77-96%) and congo red (70-82%) upon contact of initial 45 min on polymeric hybrids On the other hand, pristine polyacrylic acid and cellulose acetate showed remarkably low removal of dyes. The adsorption mechanism is proposed as physical in nature following type II isotherm. Further, Langmuir and Ho's pseudo second order fitness was evaluated. In order to determine the economic viability of the present research, the real textile dyes were recovered in three consecutive cycles of adsorption and chemical treatment of hybrids. The results propose a system with positive impact on economy by maximum utilization of hybrids as adsorbents and recovery of textile dyes for reuse in textile processing.

Preparation of silver nanoparticles/polymethylmethacrylate/cellulose acetate film and its inhibitory effect on Cronobacter sakazakii in infant formula milk.

Cronobacter sakazakii is a harmful foodborne pathogen, and its contaminated food will pose a huge threat to human health. Prevention of C. sakazakii contamination of food is valuable for food safety as well as for human health. In this study, silver nanoparticles (AgNP) were successfully immobilized on the surface of cellulose acetate (CA) and polymethylmethacrylate (PMMA) composite to obtain AgNP/PMMA/CA film. Through the inhibition zone and growth curve experiments, we found that AgNP/PMMA/CA films has excellent antibacterial activity on C. sakazakii. The AgNP/PMMA/CA film can prolong the lag phase of the growth curve of C. sakazakii from 2 to 8 h. The antibacterial films were found to reduce the survival of C. sakazakii in Luria-Bertani and infant formula by combining it with a mild heat treatment (45°C, 50°C, and 55°C). The AgNP/PMMA/CA film combined with 55°C water bath can completely inactivate C. sakazakii in infant formula within 120 min. Finally, the potential mechanism by which AgNP/PMMA/CA films reduce the heat tolerance of C. sakazakii was investigated by quantitative real-time PCR. The results showed that AgNP/PMMA/CA films could reduce the expression of environmental tolerance-related genes in C. sakazakii. The current research shows that AgNP/PMMA/CA film has strong antibacterial activity, and the antibacterial film combined with mild heat treatment can accelerate the inactivation of C. sakazakii and effectively reduce the harm of foodborne pathogens. The AgNP/PMMA/CA film can be used as a potential packaging material or antibacterial surface coating.

Dual-mode security authentication of SrAl2 O4 :Eu,Dy phosphor encapsulated in electrospun cellulose acetate nanofibrous films.

Photochromic inks have been an attractive authentication strategy to improve the anti-counterfeiting efficiency of commercial products. However, recent reports have shown significant disadvantages with photochromic inks, including poor durability and high cost. In this context, we developed novel photochromic nanofibres for advanced anti-counterfeiting applications. Lanthanide-doped strontium aluminate (LdSA) nanoparticles (NPs) were prepared and immobilized into electrospun cellulose acetate nanofibres (CANF). Authentication materials immobilized with inorganic photochromic agents can warranty durability and photostability. Therefore, the ultraviolet-stimulated photochromism of LdSA-encapsulated cellulose acetate nanofibres (LdSA@CANF) demonstrated high reversibility and photostability. A broad range of cellulose acetate nanofibres with unique emission characteristics was developed when applying different ratios of LdSA NPs. LdSA@CANF appeared colourless under visible daylight, whereas a green emission was monitored under ultraviolet-light illumination. The shape and chemical content of the photochromic fibrous films were examined using various analytical techniques. The mechanical characteristics of LdSA@CANF-coated paper were investigated. The emission wavelength was detected at 514 nm to designate green colour, whereas the excitation wavelength was detected at 369 nm to indicate transparency. The prepared cellulose acetate nanofibrous film can be described as an efficient strategy for the anti-counterfeiting of commercialized items.

Graphene nanoplatelet/cellulose acetate film with enhanced antistatic, thermal dissipative and mechanical properties for packaging.

With the increased concern over environment protection, cellulose acetate (CA) has drawn great interests as an alternative for packaging material due to its biodegradability and abundant resources; whereas, the poor antistatic property and thermal conductivity restrict its application in packaging. In this work, we proposed a simple but effective strategy to produce high performance graphene nanoplatelet (GNP)/CA composite films via the consecutive homogenization and solvent casting processes. Relying on the spontaneous absorption of CA during homogenization, the GNP/CA produced shows an excellent dispersibility in the N,N-Dimethylformamide (DMF) solution and many fewer structural defects compared with GNPs alone. As a result, the composite films obtained exhibit simultaneously and significantly enhanced antistatic, heat dissipative and mechanical properties compared with CA. Specifically, the GNP/CA composite with the optimal formula has promising overall performances (namely, surface resistivity of 3.33 × 107 Ω/sq, in-plane thermal conductivity of 5.359 W ( m · K ) , out-of-plane thermal conductivity of 0.785 W ( m · K ) , and tensile strength of 37.1 MPa). Featured by its promising overall properties, simple production processes and biodegradability, the as-prepared GNP/CA composite film shows a great potential for application in packaging. Supplementary Information: The online version contains supplementary material available at 10.1007/s10570-023-05155-2.

Cellulose Acetate-Supported Copper as an Efficient Sustainable Heterogenous Catalyst for Azide-Alkyne Cycloaddition Click Reactions in Water.

A new sustainable heterogeneous catalyst for copper-catalyzed azide-alkyne cycloaddition reaction (CuAAC) was investigated. The preparation of the sustainable catalyst was carried out through the complexation reaction between the polysaccharide cellulose acetate backbone (CA) and copper(II) ions. The resulting complex [Cu(II)-CA] was fully characterized by using different spectroscopic methods such as Fourier-transform infrared spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Energy Dispersive X-ray (EDX), Ultraviolet-visible (UV-vis), and Inductively Coupled Plasma (ICP) analyses. The Cu(II)-CA complex exhibits high activity in the CuAAC reaction for substituted alkynes and organic azides, leading to a selective synthesis of the corresponding 1,4-isomer 1,2,3-triazoles in water as a solvent and working at room temperature. It is worth noting that this catalyst has several advantages from the sustainable chemistry point of view including no use of additives, biopolymer support, reactions carried out in water at room temperature, and easy recovery of the catalyst. These characteristics make it a potential candidate not only for the CuAAC reaction but also for other catalytic organic reactions.

Impact of Ag/ZnO Reinforcements on the Anticancer and Biological Performances of CA@Ag/ZnO Nanocomposite Materials.

In this study, an unpretentious, non-toxic, and cost-effective dissolution casting method was utilized to synthesize a group of anticancer and biologically active hybrid nanocomposite materials containing biopolymer cellulose acetate. Pristine ZnO and Ag(0.01, 0.05, 0.1)/ZnO hybrid nanofillers based on variable Ag NP loadings were prepared via green procedures in the presence of gum arabic (GA). The chemical structures and the morphological features of the designed nanocomposite materials were investigated by PXRD, TEM, SEM, FTIR, TGA, and XPS characterization techniques. The characterization techniques confirmed the formation of CA@Ag(0.01, 0.05, 0.1)/ZnO hybrid nanocomposite materials with an average crystallite size of 15 nm. All investigated materials showed two degradation steps. The thermal stability of the fabricated samples was ranked in the following order: CA/ZnO < CA@Ag(0.01)/ZnO < CA@Ag(0.05)/ZnO = CA@Ag(0.1)/ZnO. Hence, the higher Ag doping level slightly enhanced the thermal stability. The developed nanocomposites were tested against six pathogens and were used as the target material to reduce the number of cancer cells. The presence of Ag NPs had a positive impact on the biological and the anticancer activities of the CA-reinforced Ag/ZnO composite materials. The CA@Ag(0.1)/ZnO hybrid nanocomposite membrane had the highest antimicrobial activity in comparison to the other fabricated materials. Furthermore, the developed CA@Ag(0.1)/ZnO hybrid nanocomposite material effectively induced cell death in breast cancer.

In Situ Decoration of Bi2S3 Nanosheets on Zinc Oxide/Cellulose Acetate Composite Films for Photodegradation of Dyes under Visible Light Irradiation.

A novel Bi2S3-zinc oxide/cellulose acetate composite film was prepared through a blending-wet phase conversion and in situ precipitate method. The results revealed that the incorporation of Bi2S3 in the film increased the cavity density and uniformity, which provided additional space for the growth of active species and improved the interaction between dye pollutants and active sites. Zinc oxide acted as a mediator to facilitate the separation of electron-hole pairs effectively preventing their recombination, thus reducing the photo-corrosion of Bi2S3. As a result, the Bi2S3-ZnO/CA composite film exhibited favorable photocatalytic activity in the degradation of various dyes. Additionally, the composite film displayed effortless separation and recovery without the need for centrifugation or filtration, while maintaining its exceptional catalytic performance even after undergoing various processes.

Review of industrially recognized polymers and manufacturing processes for amorphous solid dispersion based formulations.

Evolving therapeutic landscape through combinatorial chemistry and high throughput screening have resulted in an increased number of poorly soluble drugs. Drug delivery strategies quickly adapted to convert these drugs into successful therapies. Amorphous solid dispersion (ASD) technology is widely employed as a drug delivery strategy by pharmaceutical industries to overcome the challenges associated with these poorly soluble drugs. The development of ASD formulation requires an understanding of polymers and manufacturing techniques. A review of US FDA-approved ASD-based products revealed that only a limited number of polymers and manufacturing technologies are employed by pharmaceutical industries. This review provides a comprehensive guide for the selection and overview of polymers and manufacturing technologies adopted by pharmaceutical industries for ASD formulation. The various employed polymers with their underlying mechanisms for solution-state and solid-state stability are discussed. ASD manufacturing techniques, primarily implemented by pharmaceutical industries for commercialization, are presented in Quality by Design (QbD) format. An overview of novel excipients and progress in manufacturing technologies are also discussed. This review provides insights to the researchers on the industrially accepted polymers and manufacturing technology for ASD formulation that has translated these challenging drugs into successful therapies.

Optimization of whole-cell bacterial bioreporter immobilization on electrospun cellulose acetate (CA) and polycaprolactone (PCL) fibers for arsenic detection.

Arsenic contamination is a critical global problem, and its widespread environmental detection is becoming a prominent issue. Herein, electrospun fibers of cellulose acetate (CA) and polycaprolactone (PCL) were successfully fabricated and used as the support material for immobilization of arsenic-sensing bacterial bioreporter for the first time. To date, no attempt has been made to immobilize fluorescent whole-cell bioreporter cells on electrospun fibers for arsenic detection. CA and PCL electrospun fibers were fabricated via traditional electrospinning technique and characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and contact angle meter. Following immobilization of the bacterial bioreporter cells, the immobilized bacteria were also characterized by viability assay using AlamarBlue. The effects of growth phase and cell concentration on the fluorescence response of fiber-immobilized arsenic bioreporters to arsenic were also investigated. After immobilization of arsenic bioreporters on 10 wt% PCL fiber, 91% of bacterial cells remained viable, while this value was 55.4% for cells immobilized on 12.5 wt% CA fiber. Bioreporter cells in the exponential growth phase were shown to be more sensitive to arsenic compared to aged cells. While both the electropsun PCL- and CA-immobilized bioreporters successfully detected 50 and 100 µg/L of arsenite (As (III)) concentrations, the PCL-immobilized bioreporter showed better fluorescence performance which should be investigated in future studies. This study helps to fill some gaps in the literature and demonstrates the potential for using electrospun fiber-immobilized arsenic whole-cell bioreporter for arsenic detection in water.

Cellulose-Acetate Coating by Integrating Ester Group with Zinc Salt for Dendrite-Free Zn Metal Anodes.

Zinc (Zn) metal is considered a potential anode owing to its high theoretical capacity, safety, and low cost. However, the dendrites and corresponding side reactions in aqueous electrolytes hinder their further development in environmentally-friendly energy storage. Herein, ion-affiliative cellulose acetate (CA) coating with Zn(CF3 SO3 )2 is constructed on Zn anode (CAZ@Zn). Owing to the complexation effect between the polar ester group (CO) and Zn salt (Zn2+ ), the CAZ polymer coating enhances the hydrophilicity of the Zn anode and reduces the interfacial resistance, allowing the rapid Zn2+ diffusion and homogenizing the Zn deposition in an aqueous electrolyte to suppress zinc dendrite formation and growth. Therefore, the symmetric CAZ@Zn//CAZ@Zn battery achieves reversible plating/stripping over 2800 h at 1 mA cm-2 with 1 mAh cm-2 , about sevenfold higher than bare Zn. The full cell fabricated with an optimized Zn anode and the NH4 V4 O10 cathode achieves substantially stable performance, superior to that of bare Zn. This work provides a straightforward, effective, and scalable method to suppress the zinc dendrites and corresponding side reactions for aqueous Zn-ions batteries.